PROVN OF TRG SHED STORAGE SHED AND CHAIN LINK FENCING AT VARIOUS LOCATIONS UNDER GE CENTRAL BANGALORE

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed.

Surface excavation averaging 15cm deep and n.exc 30cm deep and getting out in soft/loose soil complete all as specified and directed

Excavating in post holes (or similar holes) each not exceeding 0.5 cu. m, getting out in soft/ loose soil and removing surplus soil outside MD land complete all as directed.

Excavation in trenches and not exe. 1.5 m wide and not exe. 1.5 m in depth for foundation of drain, man hole , laying of cables , stay etc. not exe. 10 Sq. m on plan and not exe. 1.5 m depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft rock complete all as specified and directed

M&L for earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick. Note :- Approved soft soil suitable for filling in floors shall be brought by the contractor from outside MD land

Removing excavated surplus soil to a distance exceeding 250 mts but not exceeding 500 mts & depositing where directed complete all as directed.

M&L moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering complete all as specified. (Measurements shall be taken after compaction).

M & L for Hard core of broken hard stone or boulders of guage not exceeding 63 mm , deposited spread in layers n.exc 15cm thick , watered & well rammed to true surface complete all as specified and directed.

M&L for anti-termite treatment to the bottom and sides of excavation in contact with foundation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified & as directed

M&L for anti-termite treatment to the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified & as directed

M&L for anti-termite treatment to the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified & as directed

M & L for PCC 1:4:8, type D2 using 40 mm graded crushed stone aggregate as in foundation filling mass concrete complete all as specified and directed

M & L for PCC 1:3:6, type C2 using 40 mm graded crushed stone aggregate as in foundation filling mass concrete complete all as specified and directed

Precast cement concrete 1:3:6 type C1 (20mm garded aggregate) as kerb stone set in cement mortar 1:6 complete all as directed

M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified.

Providing precast ce- ment concrete Type B1 1:2 :4 using 20 mm graded crushed stone aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry),string courses, copings. kneelers, apex stones, pier caps, columns, posts , boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets,etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match Set in cement mortar 1:4 complete all as directed.

.M&L for reinforced cement concrete M-25 (Nominal Mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

.M&L for reinforced cement concrete M-25 (Nominal Mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

.M&L for reinforced cement concrete M-25 (Nominal Mix) ) using 20mm graded crushed stone aggregate in chajjas and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO, Acco Proof, Impermo, Aqua flex as approved.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete.

Formwork to flat surfaces of chajjas, chullah hoods, troughs and similar items including edges for rough finished surfaces

SF for Powder coated aluminium (minmum1mm thickness of powder coating 50 micron) wo or doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming t IS 733 and IS: 1285,fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions

S&F for powder coated aluminium window and ventilator shutters.fixedtype/sliding type without sash bar,aluminium section weighing 0.55 Kg/m including necessary joining cleats.glazing clips.rubber packing.anodised aluminium snap beading, screws etc.. complete all as directed

S&F Stainless steel wire cloth.0.24 mm nominal dia of wireand average width of aperture1.40mm and fixed with stainless steel wire staples including supply & fix with aluminium fillet complete all as directed.

S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness, complete as specified & as directed.

S &F 35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats.

S&F 35mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified.

S & F150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S&F150 mm size butt hinges, medium weight cold rolled mild steel and fixed .

S&F 150 mm size aluminium alloy handles (ISI Marked) fabricated type anodised and fixed.

S&F in repair 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified

S&F aluminium anodised snap grid frame work for false ceiling of grid size 605x605 mm including hangers and cleats with Armstrong Optra tiles for insula-tion and accoustic purposes,60x60 cm in size, fixed aluminium fillets or with stapleson snap gridcomplete all as specified and as directed.

S & F 10 mm dia and over TMT bars cut to length bent to shape required cranking including bending , hooking ends etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per item No. 37 here- in – above but 5 mm dia and over upto 10 mm dia as in stirrups - do -

S&F Mild steel iron framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fit-tings (exclusive of steel sheeting or other cover-ing, running rails and guides) and hanging; al-so fastening and fixing complete all as directed . Steel conforming to Fe 410 -W (Gde E- 250 Quality A)

S&F rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats and gusset plates etc., conforming to Fe 410-W (Gde E-250) quality-B.

S&F mild steel tubular work in tubular trusses, roof trusses (framed), trussed, purlins, crane gantries, rails and fastemings and heavy bracket framing ( Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 with one coat of zinc chromate primer paint.

M&L Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc.

S&F mild steel work in hard rails , winds ties post and struts in fencing screwed or welded to shaped as directed , including all necessary drilling ,bolting or welding etc, and similar work confroming Fe-290 Gde-E-165.

M & L for Mild steel plate (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290, Grade E-165 complete all as directed.

S&F pre-painted galvalume (zincalume) aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to walls fixed with self tapping screws as specified.

Supply and fix Pre- painted galvalume aluminum zinc coating GI plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction all as specified and as directed.

Supply and fixing 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc complete all as specified & as directed

S&F PVC Coated Chain link fencing of dia 2.5 to 3 mm wire with 50 mm x 50 mm mesh complete all as directed .

Supply and fixing mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, length of bolt exc 15cm and not exc 30cm long and dia of neck 20 mm complete all as specified

M & L for 75 mm thick plain cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in sub base of floor and finished the surface complete all as directed.

M & L for 75 mm thick plain cement concrete 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in sub base of floor and finished the surface complete all as directed.

M&L for 25 mm thick plain cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in floor and finished the surface suitable to receive floor tiles complete all as directed.

M & L for 75 mm thick plain cement conctere 1: 3 : 6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection finished the surface fair and even complete all as directed.

M&L for 18-20mm thick Sadherhali stone slab flooring, steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit laid over and including 15 mm thick screed bedding in cement mortar 1 : 4including Rounding to edges complete.

All same as per item No 54 here - in - above but as in dado & skirting with 10 mm thick 1 : 3 cement mortar screed - do -(Note for item No 54 & 55 : i) Quoted rate is deemed to be inclusive of cement screed.)

M&L Machine pressed rubberised moulded Chequered cement concrete tiles 40cm x 40cm x 25 mm thick with grey cement and pigment set, jointed and pointed in neat cement slurry, tiles laid over and including 20 mm thick screed bed in cement mortar 1 :6 complete all as directed and specified. (Note : i) Quoted rate is deemed to be inclusive of cement screed. ii) Colour of tiles shall be got appproved before incorporation in the work)

M&L for rendering 15 mm thick in CM 1:6 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15 mm thick in CM 1:4 on stone or block masonry surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified.

All sameas per item No 58 here-in-above but 10 mm thick in cement mortar 1:6 -do-

M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work/ stone work or concrete surfaces mixed with WPC as per manufacturer instruction, and finished the surface fair and even complete all as specified and directed. (Note : WPC shall be measured and paid separately).

M&L preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as directed.

M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified.

Material & Labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces applied by mechanical means i.e Airless spray including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed.

S & F sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beads in square exc. 0.5 sqm in each pane complete all as directed.

M & L Two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed.

M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation of new steel surface complete all as directed.

M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface not exceeding 10 cm in width or girth including necessary preparation of new steel surface complete all as directed.

E&M Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium Grade) concealed conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-(a) One light / One CF or Ex fan point controlled by one 5 Amps switch one way

(b) One 3 pin socket point 5 Amp on independent board

(c) One 3 pin socket point 5 Amp on same board with other switches.(to be provide new point as user reqairment)

All as per item No. 69 here-in-above but with 2.5sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor for 3 pin 15 A socket outlet on independent board complete all as specified and directed.

Supply and fix modular switch 1 way 6A,1 module Make : Anchor/Havell/Polycab

Supply and fix modular switch 1 way 16A,1 module Make : Anchor/Havell/Polycab

Supply and fix socket, 6A-2/3 pin combined 2 modules Make : Anchor/Havell/Polycab

Supply and fix socket, 6A/16A-2/3 pin combined 2 modules Make : Anchor/Havell/Polycab

Supply and fix moduler fan Requlator, 120 W-2 modules

Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC square blocks.

S&F of LED Luminarire 600mmx600mm 35/36 Watt , 230 volt, with recessed type with high efficiency PMMA diffuser soft glare free light complete with driver holders & LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm with all as specified and directed by Engr-in-charge. Make : Crompton Greaves/Bajaj/ Philips

S&F bldg security light light fittings 1x 35 Watt Ac 230v out door type LED street light with high pressure die cast aluminium and heat ressistent complete with driver ,lamp bracket with impact and corrosion resistent including thermal managment in multiple optics complete , IP65/66 and wired with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed. Make : Crompton Greaves/Bajaj/ Philips

S&F steet light bracket made out of 25 / 36 mm mm bore GI Light grade 1.00 M long to required shape as in bracket suitable for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S & F Exhaust fans steel body Ac single phase 230 v of size 300mm sweep with blades, frame and louvers with Provn of twin core cable of suitable size for ceiling rose to connector connecting of earth wire as complete all as directed,NOTE: Quoted rate deemed to be included for Core cutting machine hole by opening in any type of walls (Stone/Bricks) in the building including neccessary plastering, grouting of nuts & bolts and washers suitable size and neccessary fixing arrangement for fixing louvre and including making good to disturbed surface area to its original position. including Mouse safty mesh to be close from out side. Make: Bajaj/ Usha.

S & F ceiling fans complete with blades, down rods,electronic regulator and accessaries 230v,1200mm sweep, Min air delivery 210 CFM with service Value 6.00 BEE Five star rated with Brushless direct current motor (BLDC) Provn of twin core cable of suitable size for ceiling rose to connector connecting of earth wire as complete all as directed

S&F Sheet metal enclosure (ISI marked) distribution board for 240 volts, SP 4 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

S & F MCB single pole 6 to 32 Amps 240 volts, 10 kA rupturing capacity providing in DB complete and old MCBs Deposit to store with all as specified and directed by Engr-in-charge. Make Indoasian

S & F MCB single pole & neutral 32 Amps 240 volts, 10 kA rupturing capacity providing in DB complete and old MCBs Deposit to store all as specified. Make Indoasian

M&L for Sand cushioning/sand covering for underground cable protection complete all as specified. Note: Punned thickness only will be measured and paid.

Supply and laying sub class 'B' bricks of old size (standard size as per local availability) laid along alignment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-Charge

S&Fmild steel galvanized pipe light grade for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site all as specified for size of 50mm bore dia.

Supply, fixing ,Teting and commissioning XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminum conductor, 1100Volt grade on walls with fixing acessories of 10 Sqmm 4 Core all as specified and directed.

M & L for Earthing to Main panel complete with galvanized steel earth plate electrode 600x600x6. mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanised earth Strip 25x4 mm as earthing lead of bolts,nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point all as specified or indicated including testing on completion including dismantling of old earthing materials.(for existing Main pillar box)

Harish Constructions

PRAGATHI BUILDERS

Aavani BUILDERS AND CONTRACTORS

Srisrinivasaenterprises

P M Constructions

D NAGI REDDY