PROVN OF SPL REPAIR/REPLACEMENT OF ACB,INTERNAL WIRING AND CONSTN OF NIGHT PICKET UNDER GE SATWARI

Amount

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes,cables,pipe line,pole etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out, in any type of soil, complete all as specified and as directed by Engineer-In-Charge.

Surface dressing n exc 15cm deep and getting out in any type of soil complete all as specified.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil, all as specified.

Material and labour for earth filling inside the basement including rough excavation and removing soil upt to 10 KM including spreading levelling and well ramming complete all as specified and directed

Material and labour for hardcore of broken stone of gauge n.exc 63mm, deposited spread and leveled in layers n.exc 15cm thick watered and well rammed to a true surface, complete all as specified and directed

Returning filling in, trenches including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type of soil complete all as specified

Removing excavated surplus materials to a distance not exceeding 50mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point Note : During excavation/taking out any damage to the existing services like telephone cable,sewage line,electric cable,water supply pipe will be repaired by the contractor at his own arrangement.No extra payment will be born by the deptt on this account.

Material and labour for ATT treating in contact with foundation at the rate of 7.5 ltrs of emulsion per sqm of vertical surface area

Material and labour for ATT treating the top surfaces of filled earth at the rate of 5 ltrs of emulsion per sqm of surface area

Material and labour for ATT treating under the soil surfaces of plinth protecion at the rate of 5 ltrs of emulsion per sqm of surface area

Material and labour for ATT treating the bottom and sides of excavation at the rate of 5 ltrs of emulsion per sqm of surface area

Supply and spreading sand Dry cushioning to cable providing with a layer of sand 8cm deep before laying the cable and 15cm deep after laying and stretching the cable in trenches complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid.

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation for sub base of PCC poles etc complete all as specified and directed

Material and labour for PCC 1:2:4 type B 1 using (20 mm graded aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering slightly rounded or chamfered angles and throating all as specified and direct. Note: Form work required for these items included in the unit rate of this item.

Pre-cast reinforced cement concrete 1:2:4, type B-1, (using 20mm graded crushed stone aggregate), nominal mix, as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs and similar articles with plain faces as specified in clause No- 4.11.16 of SSR Part-I (2009), set in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge.

Material and labour RCC (Design Mix) M-25 as in columns, pillars, peris, posts and struts etc completed all as specified ad directed

Material and labour for RCC M-25 design mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns complete all as directed.

Material and labour for RCC M-25 design mix as in column foundations complete all as directed.

Material and labour for RCC (Design Mix) M-25 as in in beams , cantilevers, bressummers, lintel over 1.5 m span complete all as directed.

Material and labour for RCC (Design Mix) M-25 as in in slabs supported on walls beams and clumns in floors, roofs, landings, balcony, canopies, deck slabs and in slaves and like complete all as directed.

Material and labour RCC (Design Mix) M-25 as in chajjas fins, facias,etc completed all as specified ad directed

Use and waste formwork to chullah, chajjas, troughs and similar items including edges. Rough finished surfaces of concrete .

Use and waste formwork to sides of concrete foundation footing base of columns and raft beams sides and soffits (if any) of plinth beams.

Use and waste formwork to sides of pillar, posts, struts, pier, column square, restangular or polygonal fair finished surface of concrete

Supply only Integral water proofing compound, complete all as specified and as directed by Engineer-In-Charge.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves etc with fair finished surface of concrete.

Cutting into existing manholes for connecting new drains,making good to pipe(internal dia 150 to 200mm), rendering,cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required

Material and labour for plain cement concrete PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specfied.

Plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation filling of stay assembly and couping of poles complete all as specified and directed

Material and labour for PCC 1:4:8 type D-2 (40mm graded aggregate) as in floor , 75mm thick completed all as specified ad directed

Machine cut kota stone 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete, , set and jointed in neat cement slurry and pointed in grey cement to match, including 20mm thick screed in cement mortar 1:3 complete all as specified and as directed by Engineer-In-Charge.

Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over screed 10mm thick in cement mortar 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, all as specified.

Material and labour Non - skid Ceramic joint less coloured tiles 400X400 X7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over 15mm thick screed bed in C:M 1:4. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

Material and labour glazed ceramic tiles in vertical surface 450x300x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 15 mm thick CM 1:4 all as specified. Make : Somany,Kajaria ( sample as approved & kept in GE's sample room)

Material and labour for precast factory made designer tiles (Rectified interlocking tiles) glazed top made in white cement and pigment base of thickness not less than 20mm in different colour and pattern (compressive strength not less than 250 kg/sqcm) set and jointed in neat cement slurry (colour and pattern as per sample kept in GE office as approved by GE) including 15 mm thick screed bed in CM 1:6 all as specified and directed by Engr-in-Charge

Plain cement concrete (1:3:6) type C-2 (using 40mm crushed stone aggregates) as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested; complete all as specified and as directed by Engineer-In-Charge.

Material and labour for salt glazed stone ware grade A 150mm bore drain pipe laid in trenches on concrete bed and jointed in cement mortar 1:2 complete all as specified and directed by Engr-in-Charge

Supply and fixing TMT bars 10 mm dia and over cut to length bent to shape required including cranking hooking ends & binding with and including MS wire (annealed) not ness than 0.9 mm dia etc. all as specified.

Supply and fixing TMT bars 6 to 8 mm dia and over cut to length bent to shape required including cranking hooking ends & binding with and including MS wire (annealed) not ness than 0.9 mm dia etc. all as specified.

Material and labour for TMT steel bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) all as specified and directed.

Material and labour for brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6mtr mean radius built in CM (1:6) complete all as directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan any radius half brick thick wall built in CM (1:4) complete all as directed.

Supply and fixing magic eye in wooden door of approved quality as per sample kept in GE sample room and as directed and specified.

Material & labour for 18/19 mm thick MDF board as in shutters/shelves etc interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed to frame work with leaping (15mm thick three side and 20 mm thick leaping hinge side, complete all as specified and directed.

Supply and fixing steel ventilators with top hung shutters including projecting type hinges with steel handle, and steel peg stay, complete all as directed.

Supply and fixing 100 mm size hasp and staple, safety type aluminium anodised with mild steel hing pin including bolt to hinge plate and fixed with screws

Supply and fixing Pressed steel frame(factory made) of size125x60mm for doors with single rebated including mild steel hinge medium weight 100 mm long and 25x3 mm flat iron in holdfast , tie bar all necessary fixing arrangement complete including back filling of chowkats in PCC 1:3:6 and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as spd and as directed.

Supply and fixing Pressed steel frame(factory made) of size105x60mm for doors with single rebated including mild steel hinge medium weight 100 mm long and 25x3 mm flat iron in holdfast , tie bar all necessary fixing arrangement complete including back filling of chowkats in PCC 1:3:6 and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as spd and as directed.

Material and labour for cement concrete type B-1, 1:2:4 (20 mm graded aggregate) in cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like incl weathering slightly rounded our chamfered angles and threading complete all as specified and directed.

Supply and fixing Factory made, plain framed, panelled shutter (two panel) 35mm thick, 2nd class hardwood with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and as directed by Engineer-In-Charge

Supply and fixing 35 mm thick glazed and skeleton shutters 2nd class hardwood as in windows, ventilators etc, open rebated and prepared to receive glass, gauze etc (with out sash bars) edges of framing plain, chamfered or roundedfitted with cut and mitred beads for scuring glass, etc size of members of shutters as specified in SSR-I, section 8, clause 8.24 (a) fixed to chowkhats complete all as directed.

Solid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing, including making good to disturbed surface of walls, complete all as specified and as directed by Engineer-In-Charge.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing butt hinges of mild steel cold rolled medium weight of size 100mm as specified.

Supply and fixing Aluminium alloy, anodised, sliding door bolt of size 300 mm with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. . (ISI Marked)

Supply and fixing Aluminium anodised, barrel tower bolts size 100 mm of extruded section and fixed complete all as specified. (ISI Marked)

Supply and fixing Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked)

Supplied and fixing fixed steel window with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.

Supplied and fixing steel window with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars.

Material & labour for framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 all as directed by the Engineer-in-Charge.

Supply and fixing WC Orissa pattern white with integral foot rest 580x 440 mm including L bend, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified Make:- Jaquar ESSCO, Cat Part No- ECS-WHT-451LE.

Vitreous China wash basin, white, flat back, size 550x410X190 mm including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32mm dia, waste coupling of chromium plated brass, complete all as specified and as directed by Engineer-In-Charge.Make : Cera,Essco,Hindware ( sample as approved & kept in GE's sample room)

PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets,PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/ damaged floor/ surfaces, fixing in repair, complete all as specified and as directed by Engineer-In-Charge.Make : Cera,Essco,Hindware ( sample as approved & kept in GE's sample room)

Supply and fixing PVC(SWR) Type B double floor trap 75 mm dia with grating including jointing with solvent cement complete all as directed.Make;Finoex/Kisan

Supply and fixing 75 mm bore PVC (SWR)Type B pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in trenches or fixed with wall complete all as directed.Make:Finoex/Kisan

Supply and fixing 110 mm bore UPVC (SWR)Type B pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in trenches or fixed with wall complete all as directed.Make:Finoex/Kisan

Supply and fixing 75 mm bore PVC (SWR) bends any radius, all as specified.

Supply and fixing 110 mm bore PVC (SWR) bends any radius, all as specified.

Supply and fixing PVC (SWR) branch bends single 'T' equal or unequal for 110 mm bore complete all as specified.

Supply and fixing PVC (SWR) branch bends single 'T' equal or unequal for 75 mm bore complete all as specified.

Supply and fixing PVC (SWR) branch piece double double 'y' equal or unequal for 75mm bore complete all as specified.

Supply and fixing PVC (SWR) branch piece double double 'y' equal or unequal for 110 mm bore complete all as specified.

Supply and fixing PVC (SWR) vent cowl of 75 mm dia complete all as specified.

Supply and fixing PVC (SWR) vent cowl of 110 mm dia complete all as specified.

Supply and fixing PVC (SWR) reducer of 110mm dia complete all as specified.

Material and labour for salt glazed stone ware gully traps square mouthed type 'P' 150mmx150mm with excavation & earth work, set in PCC M-10 (nominal mix) block measuring 45cmx45cm and cast iron grating including joints in cement mortar (1:1) complete all as specified.

Supply and fixing Rotational moulded polyethylene water storage tanks of 500 liters capacity, (cylindrical vertical with closed top) triple layered,white,hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, including making connections complete all as specified.

Material and labour for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces including preparation of new surface over 10cm width or girth complete all as directed by Engr-in-Charge

Material and labour for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces including preparation of new surface over 10cm width or girth complete all as directed by Engr-in-Charge

Material and labour for preparation of newly plastered surfaces and applying three coats of white wash on surface of walls complete all as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces and applying three coats of white wash on ceilings complete all as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper over two coat of Birla wall care putty 2 to 3 mm thick and one coat of primer complete all as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over one coat of primer complete all as directed by Engineer-in-Charge.

Vitreous China Half stall urinal flat back, size of 465x355x265mm white colour (minimum), with grating and union for discharge pipe (excluding flushing cistern and flush pipe but including of waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe grating and union for discharge pipe, fixing in repair, complete all as specified and as directed by Engineer-In-Charge.Make : Cera,Essco,Hindware ( sample as approved & kept in GE's sample room)

Supply and fixing Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed Make: essco cat No -MQT-507 or equivalent in GEM,Mark,Jaquar

Bib taps with wall flange,cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe complete all as specified and as directed by Engineer-In-Charge.Make: essco cat No -SQT-512KN or equivalent in GEM,Mark,Jaquar

Supply and fixing CP brass stop cock 15mm dia fancy type chromium plated with long sank and cup concealed type complete all as specified Make: essco cat No -MQT-514 E or equivalent in GEM,Mark,Jaquar

Supply and fixing Angle valves cast copper alloy, chromium plated fancy type half turn screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing Cromium plated, single towel rail 600mm long complete all as specified. Make:- Jaquar Cat No- AKP-CHR-35711P.

Supply and fixing ABS shower rose with swivel joints 125mm size for 15mm bore pipe, complete all as specified and as directed by Engineer-In-Charge. essco cat No -EOS-541 N or equivalent in GEM,Mark,Jaquar

S&F soap dish holder complete all as specified. Make:- Jaquar, Cat No- AKP-CHR-35731P.

Supply and fixing 150 mm dia steel grating doom with or without waste hole of PTMT (Min weights 40 gms).

Supply and fixing PVC connection 450 mm long with brass nuts and PVC washer.

Supply and fixing waste fittings (coupling) brass chromium plated 32 mm for glazed ware sink basins etc with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed.

Material and labour for urinal spreader of brass, chromium plated fixing with 15mm dia pipe.

Supply and fixing PVC Waste pipe 32mm bore for required length complete with waste coupling .Make: Prayag Cat No 3271,Hindware,Somany,CERA,Jaquar

Supply and fixing GI tubes medium grade bore of pipe 15mm fixed to wall or laid in floors etc. complete with all fittings complete all as specified.

Supply and fixing GI tubes medium grade bore of pipe 20 mm fixed to wall or laid in floors etc. complete with all fittings complete all as specified.

Material and labour PCC 1:3:6 75mm thick type C-2 using 40mm graded crused stone aggregate finished even and fair in plinth protection complete all as directed.

Material and labour for Rendering 5mm thick on concrete surface as in ceiling cement mortar 1:3 finishing even and smooth without using extra cement as in ceiling complete all as specified and directed.

Material and labour Rendering 15 mm thick in CM 1:6 up to three story building on brick wall surface or concrete surface finished even and smooth without using extra cement including all necessary scaffolding complete all as directed.

Material and labour for Rendering 10mm thick on fair faces of concrete surfaces , in cement mortar 1:4 finishing even and smooth without using extra cement complete all as specified.

Material and labour for Rendering 15mm thck in CM 1:4 mixed with integral WPA on concrete surface in roofs incl applying cement slurry @ 3 Kg per Sqm finishing even and fair without using extra cement ( WPA shall be measured separately) and then Applying Polymeric Polypropylene polymer membrane “APP” (Atactic poly propylene polymer ) modified prefabricated five layer 3mm thick not less than 3 Kg/Sqm over a coat of bitumen primer membrane 0.4ltr/sqm by the same membrane manufactured of density at 25 degree C’ 0.87-0.89Kg/Liter and viscosity 70-160 CPS, applying a coat of bitumen 85/25 grade @ 1.2 Kg/Sqm of surface and then laying APP membrane using butane torch with 10cm over laps which shall be thermo fused by flame and over the APP membrane and then Applying a coat of bitumen 85/25 @ 1.2 Kg/Sqm over the APP membrane all as specified. MAKE-IWL/Pidilite

Cutting of existing cast iron pipe line of 100/80/50 mm bore in position for inserting CI Special such as tees,bend,coller,tail piece etc for fixing of sluice valves/for branch connection etc. Note:- Exc & earth work,CI Special & sluice valves of size & lead joint shall be measured and paid separately under respective item of shedule 'A'.

Supplying, laying, jointing & testing galvanised steel tubing 20 mm bore medium grade with screwed joint together with all fitting such as bends, elbows,tees,short pieces and union etc fixed to wall,cieling,floor including taking out old unserviceable,cracked steel tubing including all fittings complete all as specified and directed. Make:- Prakash surya/TATA/Jindal.

Supply and fixing in repair Gun-metal, globe or gate valves, 20mm dia with iron wheel head, screwed both ends for iron pipe and fixedcomplete all as specified. (ISI Marked)

Material & labour 3mm thick sheet glass ordinary quality and glazing with oil putty in area n.exc 0.5 sqm each pane complete all as specified. (Make Saint Gobin)

Supply and fixing Galvanised stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified.

Supply and fixing pressed steel cup board frame of MS sheet 1.25mm thick size of frame 60 x 40 mm with rebate of 20mm wide and 12mm deep, including PCC 1:2:4 as in filling to back of chowkats including butt hinges 100mm long, paino hinges measured separately

Supply and fixing Continuous (piano) hinges, mild steel, bright finish or electro galvanised, suitable for 19mm thick shutter, all as specified .

Supply and fixing Aluminium handles cast type anodized size of 75 mm long.

Supply and fixing 25mm dia stainless steel exterior garde best quality drapery rod with 10 rings per RM fancy type as approved by the GE complete all as directed.

E/M ITEMS- Taking down carefully aluminium conductor point wiring (light, fan, light socket, power socket) complete fitting such as switches, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good disturbed surface of walls and roofs to the existing surface & finish complete all as specified and as directed.

Dismantling and taking down carefully by unscrewing unserviceable TPN/SPN DBs, main switches complete with bus bar and rails along with MCB's complete all as specified and directed.

Dismantling and taking down carefully sub-main any size and making good the disturbed surfaces of wall/ floor to match the existing wall/ floor etc complete all as specified & directed.

Material and labour for point wiring one light/fan point controlled by one, one way switch 5/6 Amp complete with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , terminated into modular galvanised suitable size sunken basex incl white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed.

Description all as per srl item No 118 but one 3 pin socket outlet 5 amp independent board.

Description all as per srl item No 118 but one 3 pin socket outlet 5 amp same board

Description all as per srl item No 118 above but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

Supply and fixing Switch piano flush botton single pole one way, 5/6 Amps, 240 V.

Supply and fixing Socket outlet 2-in-1 3/5 pin, 5/6 Amps flush type complete all as specified and as directed.

Supply and fixing switch socket outlet 2 in 1, 3 pin 5 Amp piano flush type 240 volts complete all as specified.

Supply only Switch socket combination 5 in 1, 5 and 15 Amps flush type made of polycarbonate. Make: Legrand, HPL , Havells

Supply only Socket outlet 5/6 pin, 15 Amps flush type made of polycarbonate complete all as specified and as directed. Make: Legrand, HPL , Havells

Supply only Switch piano made of polycarbonate flush button single pole one way, 15 Amps, 230 V . Make: Indoasian , HPL , Havells

Supply and fix Fan regulator 2 Module stepped type (electronic ) polycarbonate for AC ceiling fan all as specified and directed. Make: Legrand, HPL , Havells

Supply and fixing AC single phase 240 Volt 50Hz ceiling fan of size 1200mm sweep complete in white colour 5 star rating with canopy with all accessories incl nuts, bolts, clamps etc., complete all as specified and directed. Make : Havells cat part No ES-50 premium 5 star ISI marked, Crompton cat part No : Entrust 50 or equivalent in Bajaj Excel star

S & F bell push piano flush type polycarbonate 5 amps, 240 V. Make:Legrand, HPL , Havells

Supply and fixing bell Ding Dong AC 230 volts Single Phase all as specified and directed. Make: Legrand, HPL , Havells

Supply and fixing ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

Supply and fixing only lamp holder, PVC /Polycarbonate type with back plate for batten fitting.

Supply and fixing LED lamp 7watt B-22 holder base with polycarbonate body and aluminium heat sink warm white cat part No LTHPLEDLAMP7W/B22 in C&S or equivalent in Havell's/Philips.

Supply and fixing of energy saving and environmently friendly pressure die cast aluminium IP66 luminaire with high power LED as light source of rating 30 Watt LED 5000K suitable for pole dia 35mm complete .Make C&S Cat Part No LTESS12X2.5HPLED or equivalent in Bajaj,Philips,Crompton, Havell's

S & F of lamp holder,PVC /Polycarbonate type with back plate for batten fitting including bulb LED 9 Watts

Supply and fixing energy saving new generation 10W LED IP65 bulk head luminaire with opal diffuser complete all as specified and directed. Make : Havells Cat part No LHEOAOP7UZ6W010 or equivalant in Crompton/ Philips/ Wipro

Supply, Laying , connecting, testing and commissioning XLPE insulated screened PVC bedded , galvanised steel strip or wire, electric power cable (heavy duty) with aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm x 2 core, laid in trenches/passing through pipe/fixed on pole complete all as specified and as directed by the Engineer-in-Charge.

Supply & erecting in truly vertical position steel tubular swaged poles 410 SP-31 (9.00 mtrs long) complete with 300 x300x 6 mm thick MS base plate continuously welded at bottom of pole and MS sheet 2 mm thick plug welded at top, bolts, nuts & screws including one shop coat of red oxide primer and painting with two coats of aluminium paint and black and white strips 30 cm upto 1.5mtr height from top of coping in strips all as directed (Earth work & PCC shall be measured & paid for separately).

Supply & fixing GI pipe bracket 1.2mtr long, made out of GI pipe light grade 40mm dia bent to required shape, drill, welded of fixing of street light fitting including MS clamps of flat iron(40mmx4mm),nuts,bolts ,washers including painting with two coats of aluminium paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Supply & fix junction box of size 250x200x150mm made of MS Sheet 1.6 mm thick, front door openable with fixing screw painting with two coats of synthetic enamel paint over a coat or red oxide including alumn bus bar 2 Nos of size 20x3mm mounted on epoxy based post insulators and drilled holes for connection all as required and fixed to poles using MS clamp made out of 25mmx3mm MS strip and nuts & bolts of required size,MCB 10 A single pole as directed by Engr-in-charge.

Supply and fixing Exhaust fan 300 mm sweep, heavy duty, Single phase AC 230/240V, with energy efficient motor, pre lubricated double ball bearing, speed 900 rpm complete with louvers for wall mounting incl grouting, holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan incl cutting of the hole of required size for fixing of the exhaust fan along with plastering, finishing and making good complete all as specified and directed. Make : Bajaj/Havells.

Supply LED tuberod fitting 1x20 W LED, 230V, Box type complete in all respect . Cat part No DMLN1LT8-16 of Crompton or equivalent in Havells, Jaquar alongwith LED tubeRod with heat dissipation capability suitable for G-13 base tube lights base fluorescent T8/T12 luminaries, 20 watt LED wattage with colour temp of 6000 K 1800 lumens and with surge arrestor complete in all respect. Cat Part No LTT8-20 of Crompton or equivalent in Havells, Jaquar . Note:- The LED batten and LED tube rod shall be of same make.

Supply and fixing LED tube light fitting 1X20 W LED, 230V, Batten type complete with retrofit T8 Polycarbonate/Glass tube with bi-pin holder connector block etc complete with all accessories internally rewired and including connected up with twin core twisted flexible copper conductor cable with twisted flexible copper conductor cable with suitable size cat part No is LTDC30120WLED/WDI in C&S or equivalent of Philips/ Havell's/CG. Note : 1. The LED batten and LED tube rod shall be of same make. 2. Each fittings shall be marked with the CA No in black paint clearly visible to the naked eye when fitted in position.

Supply and fixing sheet metal enclosure factory made for MCBs DB SPN single pole and neutral double door 240 volts 08 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing, and commissioning and making good of wall, surfaces all as specified and directed. Make:- Legrand,Havells/Scheinder

Supply and fixing sheet metal enclosure factory made for MCBs DB SPN triple pole and neutral double door 240 volts 04 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing, and commissioning and making good of wall, surfaces all as specified and directed. Make:- Legrand,Havells/Scheinder

Supply and fixing MCB SPN complete 32 Amp with rupturing capacity 10 KA 'C' series, ISI Marked complete all as specified and directed. Make:- IndoAsian Optipro or equivalent in Havells/ Legrand

Supply and fixing MCB 4 pole 63 Amp with rupturing capacity 415-10 KA 'C' series, ISI Marked complete all as specified and directed. Make:- IndoAsian Optipro or equivalent in Havells/ Legrand

Supply and fixing MCB single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series, ISI Marked complete all as specified and directed. Make:- IndoAsian Optipro or equivalent in Havells/ Legrand

S&F E-lite LED 9 Watts tube light fitting with tube rod incl its connection with 2 core flexible copper conductor cable with suitable size complete with all accessories all as specified and directed.Make Havells/CG

Supply & laying XLPE PVC insulated, armoured, heavy duty LT electric cable with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed ,rating1100 volts grade of size 16 sqmm. 2 core including disconnecting & taking out from trenches/wall/duct carefully complete all as directed.

Supply and laying wire of size 1.5 Sqmm with PVC insulated ,PVC sheathed cable with stranded copper conductor for working Voltage 1100 Volts single core of 1.5 Sqmm .

Supply and fixing in street light fighting LED type 60 W, IP66 powder coated pressure die cast aluminium compact High power with heat resistant toughened glass with making electric connections. Make : C&S Model No LTESS24X2.5HPLED/LS or equivalent in Havell's/ HPL/ Indo asian

Material and labour for sub main wiring with single core copper conductor cable FRLS-PVC insulated and unsheathed of size 2x6 Sqmm and one No 1x4sqmm as in continuous earth wire drawn into and including PVC concealed conduit 20mm dia medium grade 1.5mm wall thickness ISI marked with all conduit fitting and fixing accessories including chesing, cutting and making good to match with existing surface complete all as specified and as directed by Engineer-in-Charge (Note:- Two single core PVC insulated 6 Sqmm cable and one single core PVC insulated 4sqmm cable with PVC conduit 20mm dia shall be measured as one length)

Material and labour for sub main wiring with single core copper conductor cable FRLS-PVC insulated and unsheathed of size 2x4 Sqmm and one No 1x2.5sqmm as in continuous earth wire drawn into and including PVC concealed conduit 20mm dia medium grade 1.5mm wall thickness ISI marked with all conduit fitting and fixing accessories including chesing, cutting and making good to match with existing surface complete all as specified and as directed by Engineer-in-Charge (Note:- Two single core PVC insulated 4 Sqmm cable and one single core PVC insulated 2.5 sqmm cable with PVC conduit 20mm dia shall be measured as one length)

Supply and fix in replacement of ACB 4 pole, 415 V, Electrical Drawout type with thermal magnetic release with over load protection, no volt release with necessary CTs, meter and cable boxes of capacity 800 Amp 50 kA with following specification:- Auxiliary switch 7a 7b ie 7NO+7NC Safty Shutter, 36 Way Auxiliary isolating contacts, AC/DC Charging Motor, Closing coil, Shunt trip, Anti-pumping Relay, Micro switches as required for operation, Cat No: AHA08N4P*TM(S) of Make: C&S or its equivalent.

Supply and fix in replacement of ACB 4 pole, 415 V, Electrical Drawout type with thermal magnetic release with over load protection, no volt release with necessaryCTs, meter and cable boxes of capacity 1000 Amp 50 kA with following specification:- Auxiliary switch 7a 7b ie 7NO+7NC Safty Shutter, 36 Way Auxiliary isolating contacts, AC/DC Charging Motor, Closing coil, Shunt trip, Anti-pumping Relay, Micro switches as required for operation, Cat No: AHA010N4P*TM(S) of make: C&S or its equivalent.

Supply and fix servo votlage stabiliser for automatic opereation, three phase, neturally oil cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilised at 415 V with accuracy + 2.5% and speed of correction 8 Volts per second and of capacity 200 KVA with following specification:- Class of insulation: A class, Additional facility: Manual operation, Degree of protection: IP 30, No load loss: less than 0.4%, Efficiency: 98-99%, Transformer Oil: New insulating Transformer oil ISI 335 marked, Input/ output termination: On copper Bus bar, Winding and wiring materials: Copper EC grade (99.9% pure), Wide Ambient temperature operation from -20oC to 50oC, Digital maltifunction Meter with manual Bypass & auto correction, Phase missing/ phase reversal alarm or cut off, overload cut-off and short circuit protection, Controlls: All the three phase controlled individually for better voltage and load management, Technology: Torridily wound variable auto transformer for linear control and greater effiiency, Applicable standard: IS 9815, ISO 9001-2015, ISO 14001-2015, International marking: CE conformity, EN61558-1:2005+A1:2009. Model SVS34L3300 Make: Hindustan power products (P) Ltd VENERT or its equivalent.

Supply, laying, testing and commissioning cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable 1100 Volts grade with standard aluminium conductor of size 150 sqmm 3.5 core all as specified and directed.

Supply & fixing cable jointing kit 11 KV (earthed) grade for indoor termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured cable of size120 sqmm to 185 sqmm complete all as specified and directed.

Material and labour for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick buried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinforcement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

M/S S K Electricals Regd

CELMAC REGD

M/S K D Construction Co

M/S RAJ ENGINEERS

M/S MANJIT SINGH AND SONS

M/S PARAMJEET SINGH