Construction of Technology Incubation Centre (TIC) of Guwahati Biotech Park at Amingaon (Phase-II)

Amount

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). 500 mm dia piles

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Single pile upto 50 tonne Safe capacity Routine test (Test Load 1.5 times the Safe capacity)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All work upto plinth level

All work above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 300x16x5 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:(c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc.gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)cum-smoke seals, microwave cured EPDM gaskets for water tightness,pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames,shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any other accreditation body which operates in accordance with ISO/ IEC 17011 and accredits labs as per ISO/IEC 17025 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm Thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado andpillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile (600 x 600 mm)

Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -inCharge. (Material shall confirm to ASTM 6063). Floor Joint of 100 mm gap

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063). Roof Joint of 100 mm gap

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length 1200 mm and secondaryintermediate cross-T of size 24x32 mm of length 600mm to formgrid module of size 600 x 600 mm, suspended from ceiling usinggalvanised mild steel items (galvanizing@ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The workshall be carried out as per specifications, drawing and as per directionsof the Engineer-in-Charge. With 15 mm thick tegular/butt edged without perforation plain/designer light weight calcium silicate Anti-Microbial Bio-Safe coated false ceiling tiles Confirming to JIS-Z2801 and ASTM G-21

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’.The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)

Celing 12 mm cement plaster of mix 1:4 (1 cement: 4 coarse sand)

Inside Wall 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)

20 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied@ 2.20kg/10 sqm

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Applying priming coat With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work(hard and soft wood) having VOC content less than 50 grams/ litre

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1or 2 layers without gap of time.)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior,sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent,clear or pigmented, textured or smooth as specified. 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified sq

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing floor mounted, white vitreous china single piece,double traps syphonic water closet of approved brand/make, shape,size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing stainless steel A ISI : 304 (18/8) kitchen sink as per IS : 13983 with CI brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink without drain board 610 x 510 mm bowl depth 200 mm

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete,including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin: 32 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. [for Basin / Urinal / Sink waste] 40 mm dia

50 mm dia

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

Providing and fixing soil, waste pipes : Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 100 mm dia

Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron / cast iron (spun) pipes embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls, etc. For 100mm diametre

Providing and Fixing shielded coupling for Hubless centrifugally cast iron pipe. 100 mm SS 304 grade coupling with EPDM Rubber gasket.

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100 mm dia

Providing and fixing plain bend of required degree. 100 mm dia

Providing and fixing double equal plain junction of required degree. 100x100x100x100 mm

Providing and fixing single equal plain junction of required degree : 100x100x100 mm

Providing and fixing double equal plain invert branch of required degree: 100x100x100x100 mm

Providing and fixing single equal plain invert branch of required degree :100x100x100 mm

Providing and fixingHubless centrifugally cast (spun) iron terminal guard (slotted cowl) -100 mm dia as per IS 15905

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Cutting chases in brick masonry walls for following diameter sand cast iron / centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 12.50 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand). 100 mm

Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate, grey or buff, etc., over a coat of primer (of approved quality) for new work. 100mm diametre pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.(Concealed Work) 15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External Work 20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

50 mm nominal dia Pipes

65 mm nominal dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. [for Municipal and Bore Well supply to UGT/ UGR TO OHR] 40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia nominal bore

80 mm dia nominal bore

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 50 mm diameter pipe

65 mm diameter pipe

80 mm diameter pipe

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : 50 mm diameter pipe

65 mm diameter pipe

80 mm diameter pipe

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

Providing and fixing brass bib cock of approved quality. 15 mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end). 32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing ball valves (brass) of approved quality, High or Low pressure with plastic floats complete. 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Making holes up to 20 x 20 cm and embedding pipes up to 150 mm dia in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggeragate 20 mm nominal size) including dispoal of malba.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 100 mm

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W pipe including bed concrete as per standard design. 150 mm Diameter S.W Pipe

200 mm Diameter S.W Pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

450 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with R.C.C top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) and inside plasreting 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S (non-modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal dimeter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S (non-modular) bricks of class designation 7.5

Extra for depth of manholes Size 90x80 cm With common burnt clay F.P.S (non-modular) bricks of class designation 7.5

Size 120x90 cm With common burnt clay F.P.S (non-modular) bricks of class designation 7.5

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 250 to 300 mm diameter

For pipes 350 to 450 mm diameter

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality M D - 10 Circular shape 500 mm internal diameter

Providing, laying & fixing of Flotex Flocked Carpet Flooring with nylon fibre 6.6pile,80m fibers per sqmt.with 2layer PVC foam & compact PVC layer to make suitable for mechanical wet cleaning.The flooring to be lain over even tiled flooring with necessary adhesive complete as specified & directed by the department.

Providing, laying & fixing of Anti static Vinyl Flooring with necessary adhesive complete as specified & directed by the department. The flooring to be lain over even cement flooring

Supplying, Fixing and Fitting of not less than 62 mm thick wall panelling with 12 mm thk BWR grade Plywood of Greenply/Century make fixed over Gyp steel flanged studs fixed vertically on brick wall at interval of 450mm c/c. The 12 mm thick BWR grade Plywood of approved brand to be fixed on the face with 25mm drywall screw at 300 mm c/c to one sides of 50 mm studs (0.55 mm thk having one flange of 34mm and another of 36 mm made of GI steel with joints staggerred to be complete in all levels as per design and as directed by the department.

Supplying, Fixing and Fitting of not less than 50 mm thick wall panelling with 12 mm thk BWR grade Plywood of Greenply/Century make fixed over Gyp steel flanged studs fixed vertically on brick wall at interval of 450mm c/c. The 12 mm thick BWR grade Plywood of approved brand to be fixed on the face with 25mm drywall screw at 300 mm c/c to one sides of 50 mm studs (0.55 mm thk having one flange of 34mm and another of 36 mm made of GI steel with joints staggerred. Finished layer of 1 mm thick laminate of Greenlam/Century/Merino make has to be fixed over the 12 mm plywood base with necessary grooves of 2mm x 2mm (as per design) of Green/Century make laminate including all necessary hardwares complete in all levels as per design and as directed by the department.

Providing and fixing 25mm thick exterior grade MDF board panelling with CNC cutting as per design given by Architect with Painting and all complete.(Cost of painting will paid seperately)

Providing and fixing of 6 MM thick lacquered glass of approved color by Architect fixed with SGG PLANIFIX (double sided tape) on a perfectly leveled 6 mm thick water proof marine plywood / MDF which is mounted on the RCC wall/any other structure. Double sided tape to be made of plythene foam, 24mm wide, 1-1.5mm thick and to be used along-with adhesive enhancer (primer).

Providing, supplying and fixing of Frameless Single leaf/double Swing Glass Door of Dorma/ Ozone or equivalent make in glazing using 12mm thick toughened glass of Saint Gobain / or approved equivalent with die cast patch fitting with stainless steel cover including fixing of patch fittings, floor springs, locks, handles etc. using the hardware items as detailed, complete in all respects as per detailed drawings, specifications and direction of Engineer in charge. Single Leaf Door with Dorma or Equivalent Hardware’s as specified:- Swing Glass Door which includes each of Top Pivot PT 24, Bottom Patch PT 10, Top Patch PT 20, Floor Lock US 10, Strike Plate , Floor Spring BTS 75v, with pair of TGDIH SS Pull Handle 25 mm dia x 450 mm long and other accessories for self closing feature as per detailed drawings.

Providing,fitting & fixing of 30mm thick BWP grade (Green/Century/Archid or equivalent) solid core Flush Door wiith 1mm thick laminate (Green/Century or equivalent make) on both sides along with fittings,beadings etc.fixed with 4"Heavy duty S/S hinge with necessary adhesive complete as specified & directed by the department.

Glass door with 12 mm thick clear toughened glass including all accessories with Dorma make Sensor mechanism equipment with Magnet system overpanel complete as per design and as directed at all levels.

Supplying, Fixing and Fitting of Thermal and acoustic insulation board for wall, CELENIT ABE Wood Wool Board consisting of mineralized extra-thin fire wood wool bound with white Portland cement. Wood wool is 1 mm wide. High quality boards for design acoustic absorption systems. It complies with EN 13168 and EN 13964. The boards are certified by ANAB-ICEA and natureplus for eco-compatibility of materials and manufacturing process. CELENIT ABE is PEFC™ certified. Also available with FSC® certification.

Supplying, Fixing and Fitting of Thermal and acoustic fabric of Response make cotton In excess of 50,000 cycles (800g/12KPA) martinadale BS EN 1021-1: 1994(Cigarette) BS 7176: 1995 Low Hazard Flammability performance is dependent on the combination of material used. This special treatment is applied to provide water and stain repellency

Supplying, Fixing and Fitting of not less than 75 mm thick partition wall with 12 mm thk BWR grade Plywood of Greenply/Century make fixed over Gyp steel flanged studs fixed vertically onfloor and ceiling at interval of 450mm c/c. The 12 mm thick BWR grade Plywood of approved brand to be fixed on the both sides with 25mm drywall screw at 300 mm c/c to one sides of 50 mm studs (0.55 mm thk having one flange of 34mm and another of 36 mm) made of GI steel with joints staggerred, including 1mm laminate of Greenlam/Century/Merino make on both sides of the partition to be pasted on 12 mm plywood base to be complete in all levels as per design and as directed by the department.

Providing and fixing 2.4m high FRAMELESS GLASS INTERNAL PARTITIONS at all locations with 12mm clear tempered glass or as per elevation drawings enclosed with approved make of 316 grade patch connector S.S. fittings of DORMA/Ozone or equivalent make , fixed with S.S. screws or with fixing clips including necessary filling up gaps at junction, at top, bottom u channel make jindal and sides with required weather silicon with backer rod shall be inserted between alluminium section channel and glass as well as both inside and outside around the periphery of the glass to make the glazing water tight and air tight as shown in enclosed drawings and directions of Engineer-in-charge. Glasswork including making suitable holes in the glass before tempering process of glass, for installation complete as per design drawings. The periphery shall have to be sealed both from inside and outside with silicon weather sealant to make the glazing water and air tight.The sealing of glass to patch connector hardwares with stainless steel fixtures as detailed in drawings. Silicon sealant grade shall be "Dow corning - USA" or " "WACKER - Germany" or approved equivalent as per the design requirement. The partition shall be aligned for the entire height and for the entire length by laser beam equipment to ensure 100 percent X-axis and Y-axis alignment. The glass joints must be properly sealed with weather silicon to make the joint water tight and air tight as well as per design complete at all levels and as directed.

Providing & placing custom made Cabinet made of 12mm thick MRB board (Green/Century/Archid or equivalent) & finishing with 1mm thick Laminate (Green/Century/Archid or equivalent)of approved shade fixed with necessary adhesive and make as per design along with Auto hydalic hinges,s/s handle,100mm complete as directed by the department.

Repro Storage (600 wide)- This storage would be made of 18mm thick pre laminated particle board having hing shutters with proper locking arrangement.

Providing & fixing custom made wall mounted TV Cabinet (1200mm x 300mm x 300mm) made of 12mm thick MRB board (Green/Century/Archid or equivalent) & finishing with 1mm thick Laminate (Green/Century/Archid or equivalent)of approved shade fixed with necessary adhesive and make as per design along with necessary fixtures & fittings complete as directed by the department.

Providing and constructing loose storage (at Bed side) of depth 450mm x width 450 x 675 Height , and size as per drawings, with top, side and bottom in 19mm thick solid ply , back in 12mm thick solid ply, inetrmediates in 19mm thick solid ply , Drawer in 19mm board thick marine ply & open space . All external surfaces to be finished in approved 1mm thick laminates, with balancing laminate on the interior surface. All exposed edges for inetrmediates to be in laminate edge binding finished with matching paint.handles to be made groove handles cut in 19mm ply. Rate to include hardware such as , approved locks, drawer chanel etc(hettich/haffle/doma make) complete.Front elevational area to be measured.

Providing and constructing full height wardrobes of depth 600mm /500mm and size as per drawings, with top, side and bottom in 19mm thick solid ply , back in 6mm thick solid ply, inetrmediates in 19mm thick solid ply , shutter in 19mm block board .All external surfaces to be finished in approved 1mm thick laminates, with balancing laminate on the interior surface. All exposed edges for inetrmediates to be in laminate edge binding or teak wood lipping finished with matching paint.handles to be made groove handles cut in 19mm ply. Rate to include hardware such as rods, approved locks, L hinges for shutters, approved handles, door stop, tower bolt, etc(hettich/haffle/doma make) complete.Front elevational area to be measured.

Providing and constructing half height wardrobes of depth 600mm /500mm and size as per drawings, with top, side and bottom in 19mm thick solid ply , back in 6mm thick solid ply, inetrmediates in 19mm thick solid ply , shutter in 19mm block board .All external surfaces to be finished in approved 1mm thick laminates, with balancing laminate on the interior surface. All exposed edges for inetrmediates to be in laminate edge binding or teak wood lipping finished with matching paint.handles to be made groove handles cut in 19mm ply. Rate to include hardware such as rods, approved locks, L hinges for shutters, approved handles, door stop, tower bolt, etc(hettich/haffle/doma make) complete.Front elevational area to be measured.

Providing and fixing low height storage cabinet (Pedestal) of size 450mm deep, 600mm high made in 19mm thick plywood frame work to profile as per the detailed drawings. The storage unit shall have shutters & Drawer made in 19mm /12mm /6mm thick plywood, the top shall be finished in laminate of approved shade and make as per the detailed drawings adhering to finishing schedule. All the exposed plywood surface(internal & external) shall be finished in laminate of approved shade & make edge with lminate finish as per the detailed drawings. This also includes providing necessary hardware like handles, hinges, tower bolts/ball catches, locks, adjustable shelf pin etc. as per the detail drawings.

Tensile Membrane Fabric Providing, fabricating assembling and erection of pre stressed TensileMembrane Fabric structure in desired profile as perdrawing, with Type II, Mehatop N having aminimum weight of 950 g/sqm as per particularspecification with a 15 years warranty etc. (Rateincludes cost of fabric, shop drawings, patterningforming, cutting, fabrication, hot weld stich offabric, over steel frames with all fittings andfixtures (Note: Actual Surface area of fabric shall only be measured for payment.)MS Structure Structural Steel Work Providing, Fabricating,Assembling, painting, hoisting, erecting and placing in position MS Built-up section/Tubular Structure (MS built-up section :-Rolled section & plates confirming to IS 2062 minimum required grade E250, Tubular Structure:- made from Steel hollow sections, ISI marked from SAIL 7 RINL/TATA/JINDAL/APPOLO or equivalent conforming to IS 1161/1239/4923, minimum required Grade YST 240, in the profile shape as per drawings with special plate connector, pinion joints, Plates, hollow sections etc. using flame cutting system, SAW/MMAW/MIG welding process with special plate connectors, pinion joints,plates, hollow sections to all heights, tools and plants and necessary scaffoldings etc. required for all operations involved. The structural members shall be painted with 300 DFT anticorrosive protection coating using Paint/Primer of approved make with one or two coat of Epoxy Primer cum MIO 150 microns thick and final coat of polyurethane paint 100 microns thick (to be applied in 2 coat) The item shall be executed as per approved drawings and direction of the Engineerin-Charge complete.

Supplying, fitting and fixing of Frosted glass Film (Sparkle Film) on 12mm thick Toughen Glass for both side as per direction of the department.

Providing And Fixing Of Decorative High Pressure Laminated Sheet 6 Mm Thick , Of Plain / Wood Grain In Gloss / Matt/ Suede Finish With High Density Protective Surface Layer And Reverse Side Of Adhesive Bonding Quality Conforming To IS : 2046 Type S, Including Cost Of Adhesive

Supplying, fitting and fixing of 6 mm thick Solid Surface (Romano Corian Solid Surface) with necessary polish complete at Assam Electricity Regulatory Commission Office at Six Mile, Guwahati at all levels as specified and directed by the Daprtment.

Providing and fitting Grab Bars (Jaquare make) such as Grab Bar Left 90 Degree Angle, Grab Bar Vertical Swing, Grab Bar 842mm Long etc. for Physically Disabled Persons toilet of in all respect as specified and directed by the department.

Providing, fitting and fixing of manually operated Black out Roller blinds Hunter Douglas/ Marvel make with necessary hardware complete as per choice and as directed complete at all levels.

Supply fitting and pasting of wall paper on existing painted wall surface as per choice of design and texture with glue and edges cut to give a even look both vertically and horizontally.

Providing, fitting and fixing of manually operated good quality Curtain with track with necessary hardware complete as per choice and as directed complete at all levels.

Providing and fitting Office High Back Chair (Featherlite make) for office staff in all respect as per direction of the depertment. MODEL : OPUS HB,Self Calibarting Multilock Mechanism,Asynchronous adjustable arms, One way adjustable arms,Nylon base

Providing and fitting Office Medium Back Chair (Featherlite make) for office staff in all respect as per direction of the depertment. MODEL : OPUS MB, Self Calibarting Multilock Mechanism,One way adjustable arms,Nylon base

Supplying of 35 mm X 15mm ovel crc pipe of 18 gz powder coated with moulded ply seat & back fabric upholstary Class Room chair with half writing pad with malamime coated.

Providing & fitting 3 seater Visitor Chair with arms (Godrej make) for office purpose in all respect as per direction of the depertment. MODEL : Air 3 seater with 2 arms

Providing and fitting Dining Chair (Nilkamal make) for Canteen purpose in all respect as per direction of the depertment.

Providing and fitting 3 seater sofa with arms (Godrej make) for Hostel purpose in all respect as per direction of the depertment. MODEL : Pisa 3 seater sofa

Providing and fitting 2 seater sofa with arms (Godrej make) for Hostel purpose in all respect as per direction of the depertment. MODEL : Pisa 2 seater sofa

Providing and fitting 1 seater sofa with arms (Godrej make) for Hostel purpose in all respect as per direction of the depertment. MODEL : Pisa 1 seater sofa

Supplying of RIWOO make Leatherite Single seater sofa

Providing and fitting Centre table with Glass finish (Godrej Make) for office purpose in all respect as per direction of the depertment. MODEL : Pisa Centre Table

Providing and fitting Centre table with Wooden finish (Godrej Make) for office purpose in all respect as per direction of the depertment. MODEL : Bloom Centre Table

Providing and fitting Side table with Glass finish (Godrej Make) for office purpose in all respect as per direction of the depertment. MODEL : Pisa Side Table

Supplying of Round Meeting table- 900mm dia This table would be free standing table. the table top would be made of 25mm thick prelaminated particle, supported on 25*50mm MS Leg side and connector duly powder coated. There would be an access flab and vetibrae for the table.

Workstation- 1500x600mm The table top would be made of 25mm thick prelaminated particle board,supported on 25*50mm MS Leg sides and connector duly powder coated. There would be 60mm thk aluminium partition of 1200mm height in laminated below and fabric/white board above the table. There would be a 3 drawer pedestal of size 650mm Ht x 400mm W x 450mm D made of 18mm thick PLB finish having lock and handles.

L shape Workstation- 1500x1500mm The table top would be made of 25mm thick prelaminated particle board,supported on 25*50mm MS Leg sides and connector duly powder coated. There would be 60mm thk aluminium partition of 1200mm height in laminated below and fabric/white board above the table. There would be a 3 drawer pedestal of size 650mm Ht x 400mm W x 450mm D made of 18mm thick PLB finish having lock and handles.

Hot Desk - 2700x900mm The table top would be made of 25mm thick prelaminated particle board,supported on 25*50mm MS Leg sides and connector duly powder coated. There would be a sofboard screen of 28mm thick of size 300mm Ht x 750mm L. There would be a beam raceway below the table top.

Conference Table-3500x1200mm The table top would be made of 25mm thick pre laminated partical board supported on 50x50mm thick Ms Legs and connector duly powder coated. There would be 3 nos of access flab on the table top and vertibrae below.

Providing and fitting Single beded hostel bed including all furnishing items like mattress,pillow,bed cover,blanket etc,as per direction of the depertment.

Providing & placing custom made Hostel room Table consisting of 19mm & 12mm thick MRB Ply board (Green/Century/Archid or equivalent) & finishing with 1mm thick Laminate (Green/Century/Archid or equivalent) and providing fitting & fixing with drawer, storage,shutter etc. as per drg.The drawer is fitted with telescopic channel, auto hydralic hinges,Godrej drawer lock,ss Handle 100mm including varnishing & ploshing complete,as per direction of the depertment.

Providing and fitting Dining Table (Godrej make) for Canteen purpose in all respect as per direction of the depertment. MODEL : Oregano

Supply, installation & commissioning of 2 Nos. Vertical Multi Stage Centrifugal Pump for Clear Water with 50Hz, 380-415V, 2 Pole IE3 efficiency class motor (As per IEC standard). Pump shall be CI with CED quoted- Suction & Discharge Casing, SS 316 -Shaft and all other components will be with SS 304, Mechanical Seal (SiC vs SiC face) . Pump should have minimum 70% efficiency. Pump controller suitable for 2 Pumps (1W+1S) with LCD screen displays, phase loss protection (incoiming as well as for outgoing), Individual pump overload protection, individual pump under voltage protection, dryrunning protection without installing any float switch, memory function when power off and during recovery, visual and audio alarm for fault prompt, auto manual switch, and pump should operate based on the sump water level and both pump should run together for high level. Panel should come with 3 Nos Float switch to work as per the sump water level. (Make : KSB/WILO) Flow Rate-3 m3/hr (1W+1S) Head-10m

Ball Float (Mechanical) Supply, Installation & commissioning of reputed make mechanically operated ball float with Brass Arm for each tank for closing & opening the inlet of each tank as per the water level in each tank suitable for handling 10 Bar pressure

Providin, laying, testing & commissioning of "C" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanged, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall / ceiling with suitable clamp /support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 150 mm

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze / gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm

Supplying, fixing, testing and commissioning of Non-Return Valve of folloing sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required: 150 mm

Supplying and fixing Single headed internal hydrant valve with instantaneous unmetal / Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked comforming to IS 5290 (Type - A) with blank Gunmetal / Stainless Steel cap and chain as required: SingleHeaded Stainless Steel

Supplying and fixing 63mm dia, 15m long RRL hose pipe with 63mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required: Gun Metal

Supplying and fixing first-aid Hose Reel with MS constructions spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipments on wall. Connections from riser with 25mm dia stop gun metal valve & M. S. Pipe and socket. 30 mtr.

Supplying and fixing 63 mm dia gun metal sort branch pipe with 20mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: Gun Metal

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providin, laying, testing & commissioning of "C" class heavy duty MS pipe conforming to IS 3589/IS 1239 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, anticorrosive treatment with coalter / asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. Complete as per ASTM standards/IS: 10221 for corrosion protection of pipes for the underground installation. Note: The piping installation has to be put to hydraulic test to1.5 times the working pressure & as per latest applicable codes & standard before applying paint or pipe coating or wrapping etc. complete. UNDER GROUND 150 mm dia.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze / gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 NB

Providing, installation testing and commissioning of non-return valve of folloing sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required : 150 NB

Providing & Fixing of fire extinguishers with necessary accessories, stand, trolley, etc. 6 Kg ABC (Powder Type) Fire Extinguisher. In HP Mild Steel Cylinders ISI marked fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged with ABC powder (Mono Ammonium Phosphate) pressured by Nitrogen complete in all respects including wall suspension bracket and conforming to IS:15683

ISI marked (IS:15683) portable chemical fire extinguisher, Foam type capacity 9 liters. with gun metal cap and nozzle and complete in all respects including initial fill and wall suspension brackets

ISI Marked portable fire extinguisher, 4.5kg. CO2 type fire extinguishers complete in all respect including initial fill and wall suspension brackets & shall conform to IS 2878 or latest IS

ISI marked Fire Extinguisher, Dry Chemical powder (DCP) type capacity 6 kgs conforming to IS: 2171 or latest IS including first fill & wall suspension bracket.

Providing and fixing TAC approved Fire Hose Cabinet to house fire hydrant & hose, including all other related accerrories fabricated from M.S. sheet (16 Gauge) of fully welded construction having front door with locking arrangement, partially glazed with 4 mm thick glass. Cabinet shall be powder coated & painted with post office red colour of size as shown in the drawing (or as approved by Architect) to house the hydrant valve, 15 mtr.x2 nos. hose & hose reel. The hose cabinet size is :600mm(L)x600mm(W)x250mm(D) Hose Cabinet

Supplying, installation testing and commissioning of the following ‘C’ class MS Pipe as per IS1239 for underground/over ground pipes with welded / flanged connection with saddles, supports (all with screwed/welded joints) as required including pipe of shorter lengths, tapering connecting pieces, short or long bends, specials like sockets, union nuts, elbows, reducers, plugs, Tees etc. Complete to make the system operative as required by LFA / TAC authorities the pipes will have to be laid and fixed in trenches. The work includes excavation in all types of soils and back filling, dewatering, etc., making holes in brick or RCC walls, slabs/ roofs and making good the damages by bringing to the original condition to the satisfaction of the Architect and painting two coats of approved shade(Post office red)of enamel paint over a coat of approved primer for overheads pipes and providing and fixing pyp kote (corrosion protection tape) including supply and application of pipe coating and spiral Wrapping for underground piping (wrapping should have overlap of 15 to 20 mm) etc. Complete as per ASTM standards/IS: 10221 for corrosion protection of pipes for the underground installation. Note: The piping installation has to be put to hydraulic test to1.5 times the working pressure & as per latest applicable codes & standard before applying paint or pipe coating or wrapping etc. complete. 100 mm dia.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m : Common burnt clay F.P.S (non modular) bricks of Class designation 7.5

Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment).

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Providing and wartering of irrigation water through water tanker of Horticulture features i.e. lawn, tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts as per direction of officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Trees Plant

Hedge Plant /Ground cover

Removal of garden waste by TATA 407 or equivalent including loading/ unloading and carriage upto 1 km lead,complete disposal upto designated place as per direction of officer-in-charge .

Providing and displaying of Areca Palm having ht. 2.40 m to 2.70 m with 12 to 14 suckers, well developed, fresh and healthy with lush green foliage in 35 cm size of Bucket type cement pots & as per direction of the officer-in-charge.

Providing and displaying of Croton Golden specimen having ht. 90 cm to 1.05 cm with 5 to 6 branches, well developed, fresh and healthy foliage in 30 cm size of Earthen pot/Plastic pot as per direction of theofficer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and stacking of Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and stacking of Iresine herbstii, of height 20-25 cm. full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v

Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Magnolia grandiflora of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Bignonia venusta (Golden shower) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Ipomoea purpurea (Morning glory) of height30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed Medium class PVC conduit, with modular switch,modular plate, suitable GI box and earthing the point with 1.5sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group - C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing, following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6pin 15/16 A Socket outlet

3pin 5/6 A Socket outlet

Supplying and fixing, following size/modules, GI box alongwith base & cover plate for switches in recess etc. as required. 1 or 2 Module( 75mmx75mm)

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required Telephone socket outlet

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

2 run of cable

3 run of cable

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and fixing following way, surface/ recess mounting, Vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4+24), Double door,

4 way (4+12), Double door,

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing following rating, TP/ FP MCB/MCCB in the existing MCB DB complete with connection testing and commissioning etc as reqd. 100 A FP MCCB,30KA

Supplying and fixing 5 amps to 32 amps rating, 240 / 415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Triple pole

Triple pole and neutral

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (AC Ductable unit ODU connection) 100A

Supplying and fixing30A, 415 V,TPN Industrial type socket outlet with 4pole and earth, metal enclosed plug top alongwith 30A "C" curve TPMCB, in sheet steel cnclousre, complete with connection, testing asnd commissioning etc. as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3.5C X 25 SQ. MM. AL XLPE Armoured

3.5Cx120 sq.mm AL. XLPE ARMOURED CABLE

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Upto 35 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 95 sq. mm and upto 185 sq. mm

MS perforated cable tray Hot Dipped Galvanized 150 X 50 X 1.6 mm

MS perforated Hot Dipped Galvanized cable tray Bend 150 X 50 X 1.6 mm

MS perforated Hot Dipped Galvanized cable tray Tee 150 X 50 X 1.6 mm

Providing & fixing Goods Lift 1 ton capacity,speed 0.5m/sec,Taravel height G+2

Providing & fixing Goods Lift 2 ton capacity,speed 0.5m/sec,Taravel height G+2

Providing & fixing Passenger Lift 13 persons capacity,speed 1.0m/sec,Taravel height G+2

Dome Camera: Supply of 1/3" HDIS Image Sensor, High resolution of 600TM; True Day/Night (ICR cut), AWB, AGC, BLC; 2.8-12mm vari-focal lens; Max. IR LED length 20m, Smart IR: TDN, 12V DC, PAL, IP, PoE

24X 10/100 copper port PoE+ 2 Gigabit comboport with switching bandwith 15 of 10 GBPS, forwarding rate with 64 bite packets, 4 mpps, Active V-LAN: 255, Memory-128 MB, Flash memonry- 64 MB. The switch should of fanless design. It should support all Layer-2 features alongwith smrat configuration, auto-smart ports.

32" LED Monitor

Supply& laying of PVC sheathed Two core Twin Twisted Speaker Cable 48/0.2mm 22 in existing cabletray/channel conduits

25 mm PVC condult(Medlum Duty)

MS Junction box for termination of speakercable

Supply, Installation, testing and commissioning of Above False Celling Addressable ldeal optcal smoke detector for detecting Invislble smoke partcles with Mounting Base with bullt tn Isolator

Supply& Laying of 2 core 1.5 SQ.MM Un amouredMultistrand CopperCable.

Supplying, installation, testing & commissioning of fault isolator module complete with mounting base complete as required.

Pop up Box - 8 Module

RJ 45 LAN Socket outlet, Legrand make

Supply , Installtion , Testing and comissioning of loaded 24 port CAT6 patch panel

Supply , Installtion , Testing and comissioning of CAT6 patch cord 1 Mtr for rack side switch termination.Complete etc as required.

Supply , Installtion , connection, testing and comissioning of 50 pair KRONE strip Telephone junction box in suitable enclosure as required Complete etc as required.

SITC of 6 U Rack with accessories for PoE switch.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required

6'x6' PVC Juntion Box for FA System

17W 2000 lm 4ft IP40 Al housing LED Batten-(Similar as Philips Modelno. BN100C - LED40S-6500 PSU L120 GR S4 or equivalent)

12W 1200 lm 2ft IP20 LED Batten-(Similar as Philips Modelno. BN021 LED12S 6500 PSU GR or equivalent)

6W 700 lm IP66 IK09 LED Bulkhead -(Similar as Philips Modelno. BN WT202W LED65 CW PSU S2 PC or equivalent)

11W 1200 lm deep recessed non dimable LED down light. -(Similar as Philips Modelno. DN296B LED12S-6500 PSU WH or equivalent)

18W 2000 lm Conrolled wide beam (60 deg) ultra deep-recessed Al housing antiglare (UGR<19) DALI dimable 4000k LED down light. -(Similar as Philips Modelno. DN590B M LED20S-4000 PSD WH or equivalent)

DALI dimmable driver (Philips or equivalent make)

Supply, installation, testing and commissioning of 50 x 6 mm GI Equipotlential bar S00 mm length with suitable. juncton bax to connect earthing conductor from buidling earthing to the equipment. With six knock outs for connecting the equipment earthing

4Cx10 sq.mm CU. XLPE ARMOURED CABLE

4C X10 SQ. MM. CU XLPE Armoured(END TERMINATION)

Supply of following sizes of XLPE insulated PVC sheathed aluminium/copper conductor armoured power cable of 1.1 KV grade Conforming IS 7098(Part 1) 1988 amended up to date etc complete as required. 3.5Cx50 sq.mm AL. XLPE ARMOURED CABLE

3.5Cx120 sq.mm AL. XLPE ARMOURED CABLE

Supply and installation of EB-S41 SVGA Projector Brightness: 3300lm with HDMI Port - Epson Make with Manual Projector screen of auto closing system

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch,modular plate, suitable GI box and earthing the point with 1.5sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group - A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing, following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6pin 15/16 A Socket outlet

Supplying and fixing, following size/modules, GI box alongwith base & cover plate for switches in recess etc. as required. 1 or 2 Module( 75mmx75mm)

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required Telephone socket outlet

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

2 run of cable

3 run of cable

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and fixing following way, surface/ recess mounting, Vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4+24), Double door,

4 way (4+12), Double door,

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing following rating, TP/ FP MCB/MCCB in the existing MCB DB complete with connection testing and commissioning etc as reqd. 200 A, 36 KA, FP MCCB

Supplying and fixing 5 amps to 32 amps rating, 240 / 415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Triple pole

Triple pole and neutral

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (AC Ductable unit ODU connection) 40A

Supplying and fixing30A, 415 V,TPN Industrial type socket outlet with 4pole and earth, metal enclosed plug top alongwith 30A "C" curve TPMCB, in sheet steel cnclousre, complete with connection, testing asnd commissioning etc. as required

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm), Double run

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.( provide 3 meter GI pipe

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting / sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3.5 C x 95sq.mm AL XLPE AL Cable

MS perforated cable tray Hot Dipped Galvanized 150 X 50 X 1.6 mm

MS perforated Hot Dipped Galvanized cable tray Bend 150 X 50 X 1.6 mm

MS perforated Hot Dipped Galvanized cable tray Tee 150 X 50 X 1.6 mm

24X 10/100 copper port PoE+ 2 Gigabit comboport with switching bandwith 15 of 10 GBPS, forwarding rate with 64 bite packets, 4 mpps, Active V-LAN: 255, Memory-128 MB, Flash memonry- 64 MB. The switch should of fanless design. It should support all Layer-2 features alongwith smrat configuration, auto-smart ports.

25A, Modular type socket, 25A, Modular type starter for SPLIT AC

RJ 45 LAN Socket outlet, Legrand make

Supply , Installtion , Testing and comissioning of 6 U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts. Complete etc as required.

Supply , Installtion , Testing and comissioning of unloaded 24 port CAT6 patch / jack panel for CAT6 cable termination etc complete as required.

SITC of 6 U Rack with accessories for PoE switch.

Supply , Installtion , Testing and comissioning of CAT6 patch cord 1 Mtr for rack side switch termination.Complete etc as required.

Supply , Installtion , connection, testing and comissioning of 50 pair KRONE strip Telephone junction box in suitable enclosure as required Complete etc as required.

17W 2000 lm 4ft IP40 Al housing LED Batten-(Similar as Philips Modelno. BN100C - LED40S-6500 PSU L120 GR S4 or equivalent)

12W 1200 lm 2ft IP20 LED Batten-(Similar as Philips Modelno. BN021 LED12S 6500 PSU GR or equivalent)

6W 700 lm IP66 IK09 LED Bulkhead -(Similar as Philips Modelno. BN WT202W LED65 CW PSU S2 PC or equivalent)

11W 1200 lm deep recessed non dimable LED down light. -(Similar as Philips Modelno. DN296B LED12S-6500 PSU WH or equivalent)

18W 2000 lm deep recessed non dimable LED down light. -(Similar as Philips Modelno. DN296B LED20S-6500 PSU WH or equivalent)

18W 2000 lm deep surface mount non dimable LED down light. -(Similar as Philips Modelno. SM251C LED20S-6500 PSU WH or equivalent)

Supply, installation, testing and commissioning of 50 x 6 mm GI Equipotlential bar S00 mm length with suitable. juncton bax to connect earthing conductor from buidling earthing to the equipment. With six knock outs for connecting the equipment earthing

63 A TP MCB

40A TP MCB

4C X10 SQ. MM.CU XLPE Armoured

4C X6 SQ. MM.CU XLPE Armoured

Supply of following sizes of XLPE insulated PVC sheathed aluminium/copper conductor armoured power cable of 1.1 KV grade Conforming IS 7098(Part 1) 1988 amended up to date etc complete as required. 3.5 C x 95sq.mm XLPE AL Cable

4C x 10 sq.mm CU AR. PVC Cable

4C x 6 sq.mm CU AR. PVC Cable

Supply, Installation, testing & commissioning of Cassette Type / Ductable type ceiling suspended split VRF/VRV Indoor units . The unit shall be insulated with sound absorbing thermal insulation material, Poly-styrene / Polyethylene foam. The unit shall be supplied with suitable decorative panel & resin net filter with Mold resistance. The unit shall be supplied with drain hose, clamp metal, washer fixing plate, sealing pads, screws, clamps, washer for hanging bracket & insulation for fitting. 1.65 TR CASSETTE TYPE INDOOR UNIT

3.3 TR DUCTABLE TYPE INDOOR UNIT (Ductable units shall also vary air volume as per room requirement automatically)

5.61 TR DUCTABLE TYPE INDOOR UNIT (Ductable units shall also vary air volume as per room requirement automatically)

6.6 TR DUCTABLE TYPE INDOOR UNIT (Ductable units shall also vary air volume as per room requirement automatically)

8.25 TR DUCTABLE TYPE INDOOR UNIT (Ductable units shall also vary air volume as per room requirement automatically)

Supply, Installation, testing & commissioning of Compact Air Cooled type outdoor units VRF/VRV system having hermetically sealed scroll type fully inverter compressor, VRT SMART (Variable Refrigerant Temperature or equivalent) technology, OEM must be the manufacturer of the compressors, ODU static pressure should be atleast 78 Pa, Refrigerant cooled PCB, condenser coil fabricated from Seamless Copper tube & Plate type Al. Fins of Multi Row, Axial Flow, upward throw condenser fan, Condenser fan - motor unit, insulated refrigeration piping, power / control wiring, and earthing, external wiring between Indoor & Outdoor units, all system controls-safety. The system should have flexibility to handle total 500 Rmt of ref. piping. Each Outdoor units with High Pressure switch, Fan driver overload protector, Over current relay, Inverter Overload Protector & Fusible Plug. The unit shall be suitable for 415 ± 10 % volts, 50 Hz, 3 phase AC supply, and IP 55 protection. The VRF/VRV System shall have green ref. gas only- R410a 28 HP Capacity (Fully inverter type)

46 HP Capacity (Fully inverter type)

48 HP Capacity (Fully inverter type)

Supply, Installation, testing & commissioning of Corded / cordless remotes with LCD Display for VRF indoor units

Supply, Installation, testing & commissioning of Air-Cooled Split Air-conditioners for cooling only of capacity given below suitable for operation on 230 ± 10 % volt, 50 Hz, 1 phase AC supply. The system shall full charge of regrigerant gas and oil. The unit shall be suitable for cordless remote operation and as per specifications. Each air-conditioner shall consist of one outdoor unit and one indoor unit and other accessories as listed below. 1.0 TR Capacity

1.5 TR Capacity

1.8 TR Capacity

2.2 TR Capacity

Supply, Installation, Testing & Commissioning of suitable control / communication cabling alongwith SITC of PVC conduits as required between indoor and outdoor units

Supply, installation, testing & commissioning of following interconnecting Copper Refrigerant Pipe complete with fittings, supports, jointing suitable for VRF System of airconditioning, duly insulated with Closed Cell Class 'O' Elastomeric Nitrile Rubber tubular insulation having 40-55 kg/cu.mtr. density of nominal thickness as specified between indoor & outdoor units as per specifications including protective coating on pipes exposed to sunlight as well as gas charging and commissioning as per specifications. 41.3 mm O.D.(Insulation : 19mm suction/13 mm liquid)

34.9 mm O.D.(Insulation : 19mm suction/13 mm liquid)

28.6 mm O.D.(Insulation : 19mm suction/13 mm liquid)

22.2 mm O.D.(Insulation : 19mm suction/13 mm liquid)

19.1 mm O.D.(Insulation : 19mm suction/13 mm liquid)

15.9 mm O.D.(Insulation : 19mm suction/13 mm liquid)

12.7 mm O.D.(Insulation : 19mm suction/13 mm liquid)

9.5 mm O.D.(Insulation : 19mm suction/13 mm liquid)

6.4 mm O.D.(Insulation : 19mm suction/13 mm liquid)

SITC of Refrigerant R410a for VRV/VRF system & R32 for DX system

SITC of MS Fabrication Work for duct support and angle flange/bracing etc - complete with all lifting shifting and fixing at site. MS works shall be provided with one coat of primer and two coat of synthetic enamel paint.

Supply, Fixing,testing and commssiooning of fire retardent canvas connection along with proper nut bolt joint for isolation of vibration

Aluminim Powder Coated linear grilles with VCD

Aluminim Powder square diffusers with VCD

Aluminim Powder square diffusers without VCD

AL/GI fresh air louvers with VCD

GI volume control duct dampers

Site fabricated duct made out of 120 GSM, GI sheet complete angle iron flange etc fabricated and erected as per IS 655/ Smacna standard with support rods, fasteners, gasket nut bolts canvas 22 Guage (0.8 mm Thick) GI ducting

24 Guage (0.63 mm Thick) GI ducting

Thermal insulation of SA duct insulation with 9 / 19 / 13 mm thick aluminium foil laminated nitrile rubber insulation sealed with Aluminium tape of 50mm width.Conductivity - 0.037 at 20 Deg C & Density - 40 - 60 Kg / M3 +/- 10%. 13 mm thick

Supply and fixing of acoustic lining inside sheet metal ducts with open cell elastrometric nitrile rubber of density 150Kg/cub.mtr and thermal conductivity of 0.036 W/m k 10 mm thick

Providing and fixing in position the following pipes cut to required lengths and necessary fitting with / without 9 mm thk. Nitrile Rubber Insulation having weather protective coating as per drawing. 20 mm dia. PVC pipe. with insulation

25 mm dia. PVC pipe. with insulation

32 mm dia. PVC pipe. with insulation

40 mm dia. PVC pipe. with insulation

50 mm dia. PVC pipe. with insulation

Providing and fixing in position the following pipes cut to required lengths and necessary fitting as per drawing. 65 mm dia. PVC pipe

SUPPLY & EXHAUST AIR INLINE FAN UNITS FOR TOILETS / PANTRY / WASH ROOM / ETC. INCOMING POWER TO THE FANS SHALL BE PROVIDED BY ELECTRICAL VENDOR 450 CFM, 10MM WC SP

900 CFM, 10MM WC SP

1000 CFM, 10MM WC SP

1300 CFM, 10MM WC SP

Fresh Air Fan with pre filter : 4400 CFM with 40 mm WC ESP

SITC OF ELECTRICAL CABLING WORKS Supply and Laying Armoured Power Cable 4C x 6 sq.mm (AL)

Supply and Laying Armoured Power Cable 4C x 6 sq.mm (Copper)

Supply and Laying Armoured Power Cable 4C x 10 sq.mm (Copper)

SITC OF ELECTRICAL CABLING TERMINATION WORK AL AND COPPER DOUBLE COMPRESSION GLAND RESPECTIVELY Supply and Laying Armoured Power Cable 4C x 6 sq.mm (AL)

Supply and Laying Armoured Power Cable 4C x 6 sq.mm (Copper)

Supply and Laying Armoured Power Cable 4C x 10 sq.mm (Copper)

ELECTRICAL POWER PANELS FOR VRV/VRF OUTDOOR UNITS SITC of Floor/wall mounted free standing Electrical MCC Panel as per IS standards 8623 with Protection Class of IP 54 and Fault level of 25kA. The panel made out of 16 SWG CRCA sheet finished with Siemens Grey painting. The panel shall have suitable switching arrangement for above mentioned / following VRV / VRF outdoor units. Panels shall have aluminium bus bar and with necessary power and control wiring etc. Each feeder shall have suitable RCCB/RCBO, indication lamps, The scope includes internally wired and tested Electrical Starter Panel suitable for operation of the outdoor units incl required accessories / relays / auto-manual operation and potential free contacts for fire interlocking as required. Necessary cabling, cable tray and earthing etc incomers upto the panels from main source shall not be under scope of HVAC vendor and same shall be under scope of electrical vendor. Electrical panel having suitable Incomer and following outgoings with RCBO/RCCBs for VRV ODU

CABLE TRAY & EARTHING Supply, Installation, laying and connection of G.I. perforated type cable tray for the entire HVAC workwith necessary bands, tees and clamps/couplers for fixing. All material shall be Hot dip galvanized as per Specifications. Standard length shall be 2.5 meters. 450 mm. wide. - vertical member-100mm x 2 mm thick

300 mm. wide. - vertical member-100mm x 1.5 mm thick

150 mm. wide., 1.6 mm thick GI perforated cable tray

8 SWG GI Wire for earthing

HATIMURIA DEVELOPERS PVT.LTD.

M/S RAJSHEKHAR CONSTRUCTIONS PVT LTD

Buildrite Constructions