COMPLETION OF INCOMPLETE WORK FOR SPECIAL REPAIR TO BLDG. NO P-78 AND 79 (SIL/DIL PATIENT GUEST ROOM) OF MILITARY HOSPITAL JRC AND CERTAIN OTHER SANCTIONED WORK UNDER GE (EAST) JALANDHAR CANTT

Amount

Material and labour for cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in benching, padding, roof kerbs or mud stops, coping etc rounded or chamfered on edges complete all as specified and directed

Material and labour for applying a coat of hot blown paving industrial bitumen 85/25 at the rate of 1.20 kg/ sqm over a coat of primer @ 0.3 litre per sqm over the roof surface including cleaning surfaces complete all as specified and directed

Material and labour for APP based polymeric membrane minimum weighing 3kg/ sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt. not less than 150 gms/ sqm) laid on primed surface by forced application complete all as specified and directed complete all as specified and directed. Make: Shalimar Tar Products/ IWL Ltd/ Torchar.

Material and labour for brick tile terracing with 40mm thick brick tiles laid over and including 15mm thick screed in cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed.

Material and labour for PCC (1:2:4) type B-0 using 12.5mm graded stone aggregates as in roof kerbs/ covet fillet complete all as specified and directed.

Material and labour flush pointing to brick terracing tiles in cement mortar (1:3) complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removing surplus spoil out of defence land where directed complete all as specified.

Material and labour 5mm thick cement plaster in cement mortar (1:3) as on ceiling, soffits of RCC shelves, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour 15mm thick cement mortar (1:4) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour 15mm thick cement mortar (1:6) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour 12mm thick cement plaster in cement mortar (1:6) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified

Material and labour for 15mm thick plaster in cement mortar (1:3) two layer, first layer of 10mm thick plaster in cement mortar (1:4) and second layer of 5mm thick in cement mortar (1:3) as in chajjas, beam balcony fins etc with and including wire netting of galvanized steel wire 0.91mm dia and mesh size 12mm placed in between the two plaster layers, fixed with tinned tack or wire stapled where required to make to original shape at any height to repair chajjas, beam balcony fins etc in multi storeyed buildings, top layer of plaster finished even and smooth without using extra cement including cleaning and preparation of existing RCC surfaces and applying a coat of cement slurry complete all as specified and directed.

Material and labour preparation of new plastered surface of wall and applying three coats of white washing complete all as specified and directed.

Material and labour for preparation of new plastered or un-plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and directed

Material and labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ ltr and UV resistance as per IS 15489:2004, Alkali & Fungal Resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 ltr/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 ltr/ 10 Sqm over new surface complete all as specified and directed

All as per srl item No. 15.00 here-in-before but on old surfaces

Material and labour for preparation of old surfaces of ceiling including scraping down smoke soots, moulds, moss and trading oil and greasy spots etc including cornices, pilasters etc. on plastered or un plastered surfaces and applying one coat of white wash complete all as specified.

Material and labour for preparation of old decorated surface of walls including cornices pilasters etc (plastered or unplastered surfaces), washing rubbing down and stopping of distempered and painted surface and applying one coat of Oil Emulsion Distemper including filling of wall care putty in nails hole, crack and where reqd to achieve the smooth surface of wall complete all as specified and directed.

Material and labour for preparing of old surfaces of walls and applying 3mm thick wall care putty on walls and finished smooth complete all as specified and directed

Dismantling floor, hearth or wall tiling/ china mosaic including cement mortar bedding (but not backing), removing rubbish off outside MD land complete all as specified and directed.

Material and labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3 kg of cement per sqm complete all as specified and directed.

Material and labour for vitrified ceramic tiles 10mm thick, light shade as approved, polished area of each tiles n. exc. 0.36 Sqm (square/ rectangular) in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including rendering 15mm thick in cement mortar (1:6) finished rough to fix tiles complete all as specified and directed.

All as per srl item No. 22.00 here-in-before but in vertical surfaces including 10mm thick in cement mortar (1:4)

Material and labour non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exc. 0.06 Sqm but not exceeding 0.11 Sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor finishes complete all as specified and directed.

Material and labour glazed ceramic coloured tiles of size 450 x 300 x 6 to 7mm thick as in vertical surfaces i.e. skirting/ dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10mm thick in cement mortar (1:4) complete all as specified and directed.

Demolition of cement concrete in ground floor and paving n. exc. 15cm thick (below or above ground level) complete all as specified and directed

Material and labour 50mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection/ path including finishing the concrete surface even & smooth without using extra cement complete all as specified & directed.

Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area n. exc. 1.5 Sqm each for doors and windows complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area exc. 1.5 Sqm but n. exc. 4 sqm each for doors and windows complete all as specified and directed.

Taking down and refixing the shutter in the same opening after easing and adjusting and making the door closing properly, area of shutter of exc. 1 sqm but n. exc. 2 Sqm each complete all as specified

Supply and fixing pressed steel door frame of size 105mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed

Supply and fixing pressed steel door frame of size 125mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed

Material and labour 35mm thick 2nd class hard wood factory made plain framed, panelled shutters (two panels), with lock rail and panels of 9mm thick BWP commercial ply or of veneered particle board 12mm thick with commercial veneering on both faces with rails and style. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Material and labour 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in clause 8.24 (a) of SSR Part-I; supplied and fitted to chowkhats complete all as specified and directed.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fixing factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site, complete all as specified and directed.

Supply and fixing 100mm size butt hinges extruded aluminium alloy with mild steel hinge pin anodized and fixed complete all as specified and directed.

Supply and fixing aluminium anodised, barrel tower bolts of extruded section and fixed, 150mm long all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodised, D-type, 150mm size, all as specified and directed.

Supply and fixing mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and fixing 300mm long aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified and directed.

Supply and fixing mild steel framed work for such as guard bars/ grills, grating etc with end of bars shouldered and/ or riveted forged into spikes, framed guard bars barred iron door, railings and similar work complete conforming to Fe-290 Gde E 165 including one shop coat of zinc chromate primer complete all as specified and directed.

Material and labour for galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

Material and labour for 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n. exc. 0.50 Sqm in each pane complete all as specified and directed.

Material and labour for 4mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

Supply and fixing 50mm size mild steel butt hinges, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

Supply and fixing small fittings of first hard wood such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labour; articles n. exc. 200 cucm each complete all as specified and directed.

Material and labour treating small article such as stops, covers, gully, gratings and hold fast ends & post backs of chowkhat etc tarred area n.exc 0.10 sqm each complete all as specified

Material and labour 18/19mm thick block boards, grade 2 quality, interior grade, decorative type with decorative face veneers on one face fixed with screws to timber frame work complete all as specified and directed.

Material and labour for preparation of new wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed

Material and labour brick work with old size sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius and built in cement mortar (1:6) complete all as specified and directed.

Material and labour 25mm dia mild steel pipe curtain rod with powder coating (wooden finish) heavy duty superior quality curtain rod with brackets, stops rollers etc as approved by GE complete all as specified and directed.

Supply only finials superior quality suitable for curtain rod as approved by GE complete all as specified and directed.

Taking down old GI tubing and connections including fittings 15mm bore pipe complete all as specified and directed.

Material and labour for galvanised steel tubes 15mm bore, medium grade with & including all fittings fixed to wall, ceilings and or laid in floors etc. including taking up/ down existing tubing complete all as specified and directed.

Material and labour refixing old tubing 15mm bore with necessary connection including new fittings, in new or old position in wall, ceiling and floor complete all as specified and directed.

Taking down old GI tubing and connections including fittings 20mm bore pipe complete all as specified and directed.

Material and labour for galvanised steel tubes 20mm bore, medium grade with & including all fittings fixed to wall, ceilings and or laid in floors etc. including taking up/ down existing tubing complete all as specified and directed.

Material and labour refixing old tubing 20mm bore with necessary connection including new fittings, in new or old position in wall, ceiling and floor complete all as specified and directed.

Supply and fixing in repair 15mm angle/ stop valves, fancy type chromium plated, screwed down , high pressure with crutch or butterfly handle screwed at two right angles ends for both iron pipe complete all as specified and directed.

Supply and fixing stop valves 15 mm nominal bore, cast copper fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket, fixed in repairs complete all as specified and directed.

Supply and fixing in repairs bib taps, cast copper alloy, chromium plated, long body fancy type with capstan headed, screwed down, screwed for 15mm bore iron pipe complete all as specified and directed.

Supply and fixing pillar tap, cast copper alloy chromium plated, with capstan heads, 15mm bore dia of pipe screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe, fixed in repairs complete all as specified and directed.

Supply and fixing in repair vitreous china white water closet (Pedestal pan) and trap including connection to flush pipe etc complete including PVC seat cover connecting flush pipe etc complete all as specified and directed

Supply and fixing vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest including CI 'P' or 'S' trap with providing lime concrete bedding and connecting to flushing cistern complete including breaking up existing damaged WC seat and connecting flush pipe etc and make good to floor fixed in repairs complete all as specified.

Supply and fixing in repairs PVC white low level flushing cistern 10 litre capacity with all fittings symphonic action with top push type button with inlet ball valve and float including flush pipe, ball valve, handle, PVC short bend etc. fixed on existing brackets complete all as specified and directed

Supply and fixing vitreous china wash hand basin, white, flat back 550 x 400mm excluding taps, waste chain and plug and porcelain stopper fixed on existing brackets, fixed in repairs complete all as specified and directed.

Supply and fixing PVC connection 15mm bore size with PTMT nuts of length 450mm fixed in repair complete all as specified and directed.

Supply and fixing in repairs chromium plated brass shower rose with swivel joints of size 150mm x 150mm fixed to pipe complete all as specified and directed.

Supply and fixing sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed complete all as specified and directed

Supply and fixing soap dish 160mm x 160mm x 90mm stainless steel chromium plated fixed with brass screws and rawl plug complete all as specified.

Supply and fixing brass chromium plated tubular towel rail 20mm dia, ‘D’ type, 600mm long between flanges fixed complete all as specified and directed.

Supply and fixing in repair mild steel CP grating 125mm dia circular shaped and fixing with cement mortar (1:3) on Nahani Trap or floor trap complete all as specified and directed.

Supply and fixing in repair glass corner shelf including CP railing, 250mm radius complete all as specified and directed

Supply and fixing in repair 32mm dia PVC waste pipe for WHB all as specified and directed.

Supply and fixing 100mm dia cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or fixed to walls etc. complete all as specified and directed.

All as per srl item No. 81.00 here-in-before but in floor

Supply and fixing cast iron cowls 75mm size, complete all as specified and directed.

Supply and fixing cast iron floor trap with grating including jointing to waste pipe in run lead joint fixed in cement concrete type (1:2:4) type B-1 diameter of outlet 75mm, fixed in repairs complete all as specified and directed.

Material and labour for 100mm CI bends with ducks foot or heel rest complete all as specified and directed

Material and labour for 75mm CI bends with ducks foot or heel rest complete all as specified and directed

Supply and fixing cast iron branch pipes, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches for 100mm bore pipe fitted with oval access doors complete all as specified and directed.

Supply and fixing cast iron branch pipes, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches for 75mm bore pipe fitted with oval access doors complete all as specified and directed.

Supply and fixing cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) for 100mm bore pipe complete all as specified and directed.

Supply and fixing rotational moulded polye-thylene water storage tanks, 1000 litres capacity (cylindrical vertical with closed top), ISI marked, hoisted and fixed in position all as specified in SSR Part I, complete all as specified & directed.

Material and labour ball valve brass high pressure with polythene float and fly nut complete screwed for 20mm bore dia of iron pipe or brass ferrule and fixed complete all as specified

Supply and fixing stop valves 20mm bore, cast copper alloy, screwed down with high pressure with crutch or butterfly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete, fixed in repairs, complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

Material and labour reinforced cement concrete (1:1½:3) type A-1 mix using 20mm graded stone aggregate as in slabs supported on wall, beams and columns in floor, roof, landing, balconies, canopias, deck slabs and in slef complete all as specified and directed.

Material and labour RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in slabs supported on wall, beams and columns in floor, roof, landing, balconies, canopies, deck slabs and in shelf complete all as specified and directed.

Fair finish form work to sides and soffits of floor or roof beams, beam hunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc complete all as specified and directed

Material and labour for mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed

Excavation in trenches in soft /loose soil, not exceeding 1.5 m wide and not exceeding 1.5m in depth for foundations etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc. 10 sqm on plan and getting out complete all as specified and directed.

All as per srl item No. 101.00 here-in-before but exc 1.5m in depth

All as per srl item No. 101.00 here-in-before but hard/ dese soil

Material and labour for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete etc complete all as specified and directed.

Material and labour reinforced cement concrete nominal mix in (1:2:4) type B-1 ( using 20mm crushed stone aggregate) as in foundation, rafts, footings, foundation beams, plinth beams, bases for coloumns, etc., basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Returning, filling in including leveling, watering and well ramming in layers n. exc. 25 cm thick each layer complete all as specified and directed.

Removing excavated material (soils) to a distance n. exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Soil filling in floors or pavings laid in layers n.exc 15cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified and directed

Material and labour for MS TMT bars 10 mm and over dia and cut to length, bent to shape required including cranking bending spirally for hooping for clos hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter, for rough finished concrete surfaces complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular in rough finished surfaces of concrete complete all as specified

Material and labour RCC M-25 (Design mix) using 20mm graded stone aggregate as in foundation, including rafts, footings, foundation beams, plinth beams, mass concrete and bases for columns etc complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work n. exc. 200mm thick (Horizontal or sloping) for flat & rough finished surfaces of concrete complete all as specified and directed.

Material and labour reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in roof beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Material and labour for 20-25mm thick machine cut Kota stone slab 600mm x 600mm size flooring, jointed with grey cement mixed with pigment to match the shade of the slab including grinding, rubbing and polishing to mirror finish with & including screed bed or bedding layer of mortar 15mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and directed

All as per item No 115.00 but as in skirting laid over and including 10mm thick rendering in cement mortar (1:4) as backing coat.

Material and labour for Granite (of any type) work 20mm thick machine cut (table rubbed and polished) in steps jambs, pillars, window cills, cooking platforms, shelves in cupboard, hand wash places and like including necessary cutting and grooving to walls and making good including 10mm thick in cement mortar (1:4) screed bed or bedding layer and pointing with cement mortar (1:2) with admixture of pigment to match with shade of granite complete all as specified and directed.

Material and labour cement concrete (1:5:10) type E-2 using 40mm graded brick aggregate as in filling in sunken portion and mass concrete complete all as specified and directed.

Material and labour for applying a coat of hot blown paving industrial bitumen 85/ 25 @ 1.20 kg/ sqm over a coat of primer @ 0.3 litre per sqm over the roof surface including cleaning surfaces complete all as specified and directed.

Material and labour for APP based polymeric membrane minimum weighing 3kg/ sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt. not less than 150 gms/ sqm) laid on primed surface by forced application complete all as specified and directed.

Material and labour 25cm x 25cm x 22mm thick chequered cement concrete coloured tiles with grey cement and pigment, jointed and pointed in neat cement slurry in floor laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

Material and labour preparation of newly plastered or un-plastered surface of walls including cornices, plasters etc. and applying two coats of cement base paint complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Material and labour for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands plinth courses, roof kerbs or mud stops, benching, coping, bed plates, parapets, water through and the like etc including weathering, slightly rounded or chamfered angles throating, edges of interlocking/ chequered tiles etc complete including necessary form work complete all as specified and directed

Material and labour for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including taking down old unserviceable steel window complete all as specified and directed

Supply and fixing steel rolling shutters 1mm thick, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete push pull or manual type complete all as specified and directed.

Plates 6mm (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of Fe-410-W Gde-E-250 quality 'B' complete all as specified and directed

Excavating in post holes (or similar holes) each n.exc 0.5 cum in soft/ loose soil, getting out, returning, filling in, watering and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specified and directed.

Material and labour for moorum/ red bajri filling in floors or pavings, laid in layers n. exc. 15cm thick, spread, leveled and rammed including complete all as specified and directed.

Material and labour for 40mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in floors finished even and smooth without using extra cement complete all as specified and directed

Supply and fixing rolled mild steel work roof trussed (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, Tee, Angle, Channel or Flat Sections) including distance pieces, cleats etc, Fe-410-W (Gde E-250) complete all as specified and directed.

Supply and fixing Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws as specified and directed

Material and labour for mild steel sliding door bolts 300mm long plate type stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

Supply and fixing MS pressed handles, oval type, stove enameled black 125mm size complete all as specified and directed.

Supply and fixing floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor overall length of cover plate 140mm complete all as specified.

Material and labour PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation filling, post hole, mass concrete, surface channel and drains and other similar work etc complete all as specified and directed.

Material and labour PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in bed block complete all as specified and directed.

Material and labour for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

S&F Anodised aluminium glass door with powder coating of any colour (Thickness of powder coating not less than 50 micron) for door shutters,fixed type or as specified having section size of 100 mm x 45 mm aluminium section weighing 1.0 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing,sliding door bolt 2 nos each, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. with 5 mm frosted/laminated glass fixed complete all as specified & directed by Engineer-in-charge.

S&F Anodised aluminium wiremess door with powder coating of any colour (Thickness of powder coating not less than 50 micron) for door shutters or as specified having section size of 100 mm x 45 mm aluminium section weighing 1.0 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing,sliding door bolt 2 nos each, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. with 5 mm frosted/laminated glass fixed complete all as specified & directed by Engineer-in-charge.

S&F Anodised aluminium window with powder coating of any colour (Thickness of powder coating not less than 50 micron) for window shutters,fixed type or as specified having section size of 100 mm x 45 mm aluminium section weighing 1.0 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing,sliding door bolt 2 nos each, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. with 5 mm frosted/laminated glass fixed complete all as specified & directed by Engineer-in-charge.

Material and labour for point wiring for one light point controlled by one switch with 1.5 Sqmm, PVC insulated but unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through existing surface/ concealed conduit and accessories and terminated in modular metal box and including 1.5 Sqmm stranded copper conductor PVC insulated FRLS cable green in colour as continuous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed.

All as per srl item No. 142.00 above but for one fan point controlled by one switch

All as per srl item No. 142.00 above but for one socket outlet 3 pin 5 Amps on independent board.

All as per srl item No. 142.00 above but for one socket outlet 3 pin 5 Amps on same board with other switches.

All as per srl item No. 142.00 here in before but with 2.5 Sqmm (nominal area) FRLS cable for one 3 pin 15 Amp socket on independent board including one 2.5 Sqmm copper conductor multi stranded green colour PVC insulated unsheathed FRLS cable 1100 volts grade as earth wire connected to common earth and earth dolly with all accessories complete all as specified and directed.

Supply and fixing white modular switch 1 way 6 Amp, 1 module complete all as specified and directed.

Supply and fixing white modular switch 1 way 16 Amp, 1 module complete all as specified and directed.

Supply and fixing white modular socket 6 Amp, 250 V AC 2 in1 socket with shutter combined two module complete all as specified and directed.

Supply and fixing white modular socket 6/16 Amp, 250 V AC twin socket combined two module complete all as specified and directed.

Supply and fixing white modular fan regulator , 250 V AC step type 5 steps one module complete all as specified and directed.

Supply and fixing modular metal flush box suitable for modular switch socket regulator etc of 1 or 2 modules complete all as specified and directed.

Supply and fixing metal flush mounting box of 3 module complete all as specified and directed.

Supply and fixing metal flush mounting box of 4 module complete all as specified and directed.

Supply and fixing metal flush mounting box of 6 to 12 module complete all as specified and directed.

Supply and fixing modular cover plate (WHITE) with frame 1 module complete all as specified and directed.

Supply and fixing modular cover plate (WHITE) with frame 2 module complete all as specified and directed.

Supply and fixing modular cover plate (WHITE) with frame 3 module complete all as specified and directed.

Supply and fixing modular cover plate (WHITE) with frame 4 module complete all as specified and directed.

Supply and fixing modular cover plate (WHITE) with frame 6 to 12 module complete all as specified and directed.

Supply and fixing ceiling rose surface type bakelite 65 x 50mm three terminal complete all as specified and directed.

Material and labour for sub main wiring with PVC insulated cable copper conductor FRLS two single core 6 Sqmm drawn in existing PVC rigid non metallic conduit including earth continuity FRLS copper conductor 6 Sqmm PVC insulated with green insulation complete all as specified and directed. Note: Two run of 6 sqmm wire and one run of 6 sqmm wire as earth wire shall be measured as one RM.

Material and labour for sub main wiring with PVC insulated cable copper conductor FRLS two single core 4 Sqmm drawn in existing PVC rigid non metallic conduit including earth continuity FRLS copper conductor 4 Sqmm PVC insulated with green insulation complete all as specified and directed. Note: Two run of 4 sqmm wire and one run of 4 sqmm wire as earth wire shall be measured as one RM.

Material and labour for sheet metal DB's 4 way TPN with double door epoxy coated paint inside and outside with MCB as incomer complete with neutral bar and earth bar, prewired with PVC insulated copper conductor wire of suitable size, suitable for MCB SP as outgoing complete all as specified and directed

Supply and fixing sheet metal enclosure for DBs when MCBs to be used, SPN 8 ways 240 V, with 200 Amps rated bus bar, double door all as specified

All as per srl item No. 165.00 here-in-before but 4 way

Material and labour for MCB TPN 32 Amps, B-curve complete all as specified and directed.

Material and labour for MCB SP 6 to 32 Amps, B-curve complete all as specified and directed.

Material and labour for MCB SPN 6 to 32 Amps, B-curve complete all as specified.

Supply and fixing energy saving LED batten with diffuser comprising with aluminium housing, 4 ft, 20 watt, 6500K, power factor more than 0.95, IP-20 Class-I protection with inbuilt LED driver, surge protection upto 2.5 KV, operative on 140-270 Volt AC, complete prewired, connection and testing complete all as specified and directed

Supply and fixing energy saving & environmental friendly long life versatile pressure die-cast aluminium housing luminaire with heat resistant glass and suitable optics for uniform distribution of light 35 watt LED for bldg security lights with mounting bracket and high efficiency electronic driver, having IP-65 protection, surge protection min 2 KV power factor more than 0.9 complete operative on AC supply 140 volts to 270 volts pre-wired and product should be made in India only complete all as specified. Notes :- (i) Contractor shall provide 2 years written warranty for the LED fixture complete including driver from the certified date of completion from the local office bearer of manufacturers. (ii) Contractor shall produce LM-79 & LM-80 Report of NABL accredited Laboratory duly signed by the office bearer of manufacturer.

Supply and fixing batten holder insulated body with LED bulb 10 watt complete all as specified and directed

Fixing only ceiling fan of any sweep or make, filling cavities with filler one coat after cleaning, painting the complete fan (as per previous colour) using synthetic enamel paint by spraying including replacement of flexible wire, rubber reel, nut, bolts etc. and re-fixing in original position complete all as specified and directed.

Supply & fixing steel body exhaust fan, 300 mm sweep, 900 rpm, single phase, 23 volt, heavy duty, with lowered shutter including provision of three core flexible cable of required length of size 23/.0076 from ceiling rose/ connector to fan terminal, fixing the fan on wall with suitable size of nut, bolt & washer, including making the hole in wall incl necessary civil/ plastering work to match the disturbed surface including taking down to existing exhaust fan and depositing to MES store complete all as specified and directed by Engineer-in-Charge.

All as per srl item No. 174.00 here-in-before but 380 mm sweep.

Supply, laying, testing and commissioning of LT cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor size 50 Sqmm 3.5 Core all as specified and directed

All as per srl item No. 176.00 here-in-before but 185 Sqmm 3.5 Core

All as per srl item No. 176.00 here-in-before but 16 Sqmm 4 Core

Material and labour sand for cushioning with 8cm thick layer before laying of cable and 15cm thick layer after laying of cable in trenches complete all as specified and directed.

Supply & laying old size sub class 'B' bricks laid flat in trenches over the cable with the length of brick perpendicular to the direction of cable length, adjacent/ abutting each other complete all as specified and directed.

Material and labour for earthing complete with & including galvanized MS earth plate of size 600 x 600 x 6mm thick, buried vertically in ground to a depth not less than 2.25 metre below ground level, with lop edge of earth plate not less than 1.5 below ground level connected to galvanized earth wire soldered and riveted or connected to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part-I (2009) and connected to panel board, all as specified and testing on completion including provision of earth wire 4mm dia duly protected with and including 15mm dia bore light grade GI pipe upto 7.5m from electrode to earth point including provision of the earth plate surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate and GI medium grade watering pipe of 20mm dia bore with funnel with wire mesh including all necessary excavation & earth work in any type of soil, returning filling in, removal of surplus soil to a distance 50 metre, PCC (1:3:6) type C-1 as in earth chamber, 50mm thick RCC cover using cement concrete (1:2:4) type B-1 reinforced with & including 8mm dia mild steel TMT bar @ 100mm c/c both ways with suitable handle for lifting & including form work and MS frame using MS angle of size 40mm x 40mm x 6mm complete all as specified & directed. Note: On testing, after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to the department.

All as per srl item No. 181.00 here-in-before but GI strip 32 x 6mm

All as per srl item No. 181.00 here-in-before but GI strip 20 x 3mm

Material and labour for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete all as specified and directed

Supply and fixing servo controlled voltage stabilizer for automatic operation, three phase, 50 Hz, naturally oil cooled, indoor unbalanced type, copper wound, digital display type and of capacity 150 KVA with the following specifications :-(a) Input voltage 300V-480V. (b) Output voltage stabilized at 415V ± 1% (Adjustable) (c) Rated frequency 50 Hz (d) No distortion in wave form (e) Response time not to exceed 10 mille seconds (f) Sensitivity ± 1% (g) Rate of correction 8 volt/ second for single phase and 20 volt/ second for phase to phase (h) No load losses less than 0.5% (j) Full load loses less than 2.5% (k) Duty cycle-continuous 24x7 (l) Efficiently more than 95% (m) Type of load : 3 phase, unbalanced type (n) Digital display voltmeter/ ampmeter (o) Over load/ short circuit protections (p) High/ low voltage cut off (q) By pass arrangement in case of emergency (r) Single phase sequence change protection

Supply and fixing cable jointing kit suitable for XLPE armoured aluminium cable of size 120 to 185 sqmm 3 core 1.1 KV grade cable for straight through type termination heat shrinkable joint complete with jointing material and accessories complete all as specified and directed.

Supply and fixing GI pipe light grade ISI marked of size 100mm bore for cable protection including provision of fitting along GI pipe along wall/ pole/ laid under the road/ floor complete all as specified.

Supply, installing, testing and commissioning LT panel, indoor cubicle type, floor mounted, weather and vermin proof totally enclosed made out of 2mm thick CRCA sheet machine pressed of suitable size, suitable to operate on 3 phase 4 wire system, 415 volts, 50 Hz with front openable with locking arrangement, bottom gland plate with sufficient numbers of circular cable entry holes, complete duly powder coated with 7 tank process mounted on angle iron stand made out of angle iron 50 mm x 50 mm x 6 mm, comprising with following complete all as specified and directed :- (a) Bus bar strip 4 ple and capacity 400 Amps aluminium, be based on 1.5 Amp per Sqmm, coloured with plastic coated insulated and sleaves in four colours (Red, yellow, blue and black) fixed on procelain insulators with necessary nuts and bolts and wahsers etc. (ii) INCOMING : - (a) Onload changeover switch 320 Amps, 4 pole-01 No (b) MCCB 320 Amp, 415 V, 36 KA, 4 pole, adjustable thermal & fixed magnetic type -01 No. (c) Indicator with LED lamps for RYB -01 set (d) DG/Main ON indicator - 01 Set (e) Digital Ammeter (0-400) Amps (f) Digital Voltmeter (0-500) Volts (iii) OUTGOING:- (a) MCCB 250 Amp, 415 V, 25 KA, 4 pole, adjustable thermal & fixed magnetic type -02 Nos. (b) MCCB 160 Amp, 415 V, 25 KA, 4 pole, adjustable thermal & fixed magnetic type -01 No (c) MCB TPN 32 Amp, 415V, 10 KA-02 Nos

Supply and fixing sheet steel, phosphated, powder coated single door vertical TPN DB with provision of TPN incommer 4 way complete all as specified and directed

Supply and fixing surface and wall mounted LED batten fitting, including LED tube with complete fitting of 20 watt, incluidng provision of PVC insulated sheathed round flexible wire with multi strand copper conductor of size 1.5 Sqmm 3 core 1100 Volts grade complete all as specified and directed

M/S Vinod Kumar

J S BUILDERS

Ms Sanjiv Kumar