ADDN ALTN OF EXISTING DOORS (20 IN NUMBERS) IN TO SS DOORS IN VARIOUS WARDS, ICU AND OT AT MAIN HOSPITAL BUILDING P-72 AT INHS ASVINI.

Amount

Taking down chowkat with shutters (without taking off shutters from the frames) area exc 1.5 Sqm but n.exc 4 Sqm each.

Taking down SS door with frame of size 1200 x 2100mm with all accessories and making good the disturbed surfaces as per existing including plastering complete all as specified and as directed by Engineer - in - Charge

Taking down Aluminium doors/ partition including shutters, glass, particle board and fittings with all accessories and making good the disturbed surfaces as per existing including plastering complete all as specified and as directed by Engineer - in - Charge

Demolition of brick work or stone/boulder masonry, built in cement mortar, including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work & precast concrete articles including copings etc.and removing debris outside MD land complete all as specified. Note: The place of disposal shall be find out by the contractor.

Supply and installation of hermetically sealed double swing type door of size 1350mm x 2030mm made of SS304 sheet of thickness 0.8 mm for Door Leaf and SS 304 sheet of thickness 1.2mm for Door Frame and designed to fit flush into the wall panel system on both sides. Standard 50mm panel shall have frame width of 100mm. Shutters shall be of 45mm thick sealed and PUFF insulated with polyurethane foam injected under high pressure with a minimum density of 40 Kg/Cum. Door shall be fitted with following accessories and the quoted rate shall deemed to include the following :- Stainless steel hinges 04 Nos per leaf, Stainless Steel 'D' type handles on pull side, Stainless steel push plates on push side. Standard arm door closure (TS-1002) 2 Nos each & SS tower bolt. View panel along with self-adhesive tape and silicon sealant. One side key operated locking arrangement, Asteral of the door should be integral part of design, it should not be welded with door leaf. Door frame should be uniform and not having welding. Automatic door bottom seal at the bottom of shutter complete all as per manufacturers instructions.

Ditto- all as per item No 5.00 above but of size 1350 mm x 2110 mm

Ditto- all as per item No 5.00 above but of size 1600 mm x 2110 mm

Ditto- all as per item No 5.00 above but of size 1800 mm x 2110 mm

Ditto- all as per item No 5.00 above but of size 1830 mm x 2100 mm

Ditto- all as per item No 5.00 above but of size 1700 mm x 2110 mm

Ditto- all as per item No 5.00 above but of size 1350 mm x 2090 mm

Ditto- all as per item No 5.00 above but of size 1350 mm x 2080 mm

Ditto- all as per item No 5.00 above but of size 1530 mm x 2110 mm

Ditto- all as per item No 5.00 above but of size 1830 mm x 2110 mm

Ditto- all as per item No 5.00 above but of size 1778 mm x 2110 mm

Ditto- all as per item No 5.00 above but of size 1350 mm x 2030 mm

Ditto- all as per item No 5.00 above but of size 1645 mm x 2110 mm

Ditto- all as per item No 5.00 above but of size 1700 mm x 2110 mm

Ditto- all as per item No 5.00 above but of size 1790 mm x 2110 mm

Material & labour for Brick work with sub-class ‘B’ brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

Material & labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) and finished even & smooth without using extra cement completed all as specified.

Material & labour for Rolled mild steel sections (Fe-410 W grade 250 quality A) as in main and cross beams, channels, stanchions, hip and jack rafters; purlins ,plates and angle cleats where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates fixed to concrete members or existing brick work as cills or jambs including base plate including drilling /welding complete all as specified and directed

Supply & fixing Mild steel Anchor bolts of dia exc 12 mm but n. exc 20 mm, purpose made, with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30 cm long embedded in concrete by drilling and fixing with sufficient machinery and fixed to roof beam at any height omplete all as specified and directed

Material & labour for preparation of new steel Surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding / backing coat and removal of rubbish out side MD land. Note: The place of disposal shall be find out by the contractor.

Taking down cement plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and rubbish off the premises. Note: The place of disposal shall be find out by the contractor.

Material & labour for machine cut machine polished granite stone 18mm to 20mm thick of approved colour in floors laid over and including 20mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of granite complete all as specified and directed by Engineer In Charge

Material & labour for machine cut machine polished granite stone 18mm to 20mm thick fixed on vertical surfaces of columns/walls including chamfering, moulding and cutting grooves at corners laid over and including 10mm thick backing coat in CM (1:4), bedded and jointed with grey cement slurry and pointed with white cement mixed with admixture of pigment to match the shade of granite stone complete all as specified.

Supply & fixing in repair powder coated aluminium (minimum thickness of powder coating 50 micron) for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified. Note :- (i) Glazing/wiremesh shall be measured and paid separately. (ii) Item shall be paid as per the weight of Aluminium section however the rate quoted shall be inclusive of the cost of neoprene beading, glazing pins, screws, handle etc which shall not be measured for arriving the weight.

Supply & fixing 12 mm thick plywood grade BWR fixed with screws including fixing teakwood beading 4mm thick on exposed sides, as in partition, cupboards, shutters etc includingapplying two coats of French polish to fillets and fixed with screws to aluminium frame work using glazing clips complete all as specified and directed by Engineer in Charge.

Material & labour for preparation of new wooden surfaces of any description over 10 cm in width or girth and applying two coats of synthetic varnishing over undercoat of varnish over wooden filler liquid transparent and make the surface fully shined complete all as specified and directed by Engr-in-Charge

Dismantling wall and ceiling board (fibre, pulp, insulation etc.) or insulation board/slab/blankets, any thickness including snap gridal as directed.

Material & labour for aluminium anodized snap grid of size 605mm x 605 mm with aluminium anodized angle 20mm x 20mm x 1.2 mm fixed along the wall and main and cross tees of size 31.75 mm x 31.75 mm x 1.6 mm & 25.4 mm x 25.4 mm x 1.22 mm respectively with ceiling cleats / angle brackets of size 15 mm x 15 mm x 1.5 mm including Hangers made out of 6 mm dia. G.I. wire (upto 1200 mm length) fixed to roof slabs by means of fasteners 10 mm dia. complete all as specified. Note -Ceiling board will be measured & paid separately.

Supply & fixing 9 mm thick gypsum board of size 595 mm x 595 mm fixed in aluminium grid frame work of any pattern in ceiling including refixing electrical fittings fan, fire censors etc and making all connections complete all as specified.

Material & labour preparation of new plastered surfaces of wall, applying one coat of wall care putty not less than 2mm thickness and making the surface even and smooth using emery paper and applying two coats of Acrylic antifungal paint (100% acrylic interior grade) over a coat of self primer complete all as specified.

Supply & fixing 5mm thick sheet glass, opaque / frosted on one side and glazing with aluminum beading, glazing pin etc in suare n exc .5 sqm in each pane complete all as specified.

AGRAWAL ASSOCIATES (BID ID -3102712)

satguruenterprises (BID ID -3105198)

GANGAJAL (BID ID -3099792)

Unitech Enterprises (BID ID -3103380)

AAGAM ENTERPRISES (BID ID -3118142)

N F ENTERPRISES (BID ID -3119088)

SAHU AND SAHU CO. (BID ID -3104025)