Loading
Loading…
Loading…
Tender Value
₹5.3 Cr
EMD Value
₹10.6 L
Closing Date
27 Apr 2026, 3:30 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
SIGNAL
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less ; where V = Advertised value of the tender in crores of Rupees N = Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure- I, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited. : Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Any work of Provision of Maintenance Free earthing or Conventional earthing arrangements. OR Any Signaling or Telecom work which includes Maintenance Free earthing and/or Conventional earthing arrangements. Note 1:Tenderer may be required to submit the schedule of those works, Completion/Performance Certificates of which have been submitted by him/her in support of 30 %/ 40 % / 60 % (as the case may be) criteria of similar nature of work.
22 conditions · 13 needing a document upload
PAN card Copy should be enclosed.
Please submit the copy of the registration certificate as applicable, GSTIN certificate should be enclosed.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Firm has to submit authorization letter for uploading documents on IREPS in case he/she is not an authorized person.
Contractors are allowed to make payments against this tender towards tender document cost and earnest money only through only payment modes available ON IREPS portal LIKE net banking, debit card, credit card etc.Manual payments through Demand draft, Banker cheque, Deposit receipts, FDR etc. are not allowed.
Copy of PAN number and GSTIN number should be submitted.
No post tender correspondence for submission of additional documents shall be entertained after opening of the Technical & Commercial offers. Even suo-moto post tender letters of the tenders shall be treated as NULL & Void.
(i)Tenderers will examine various provisions of the Central Goods and Service Tax Act, 2017(CGST)/Integrated Goods and Service Tax Act,2017(IGST)/Union Territory Goods and Service Tax Act,2017(UTGST)/respective states State Goods and Service Tax Act(SGST) also, as notified by Central/States Govt. and as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit(ITC) likely to be availed by them is duly considered while quoting rates. (ii) The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/UTGST/SGST Act to railway immediately after the award of contract, without which no payment shall be released to the contractor. The contractor shall be responsible for deposition of applicable GST to the concerned authority. (iii) In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism(RCM) and deposit the same to the concerned authority.
Tenderer should go through Annexure 1 & 2 of Tender Notice (attached in Tender Document)for list of documents required to be uploaded along with the offer.
S&T work i.c.w Improvement of earthing arrangements as per latest RDSO guidelines No.- RDSO-SIG0SPD(PROJ)/1/2020, dated 01.01.2025 over LKO division of Northern Railways.
106-Sig-Tender-01-2026-27
106-Sig-Tender-01-2026-27
Open
Works - General
365 Days
Lucknow, Uttar Pradesh
₹0
₹10.6 L
27 Apr 2026
6 Apr 2026
13 Apr 2026
65 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 5,28,42,608.35 | ||
| — | 806.00 | — | — | ||
| Supply of basic material to construct Maintenance Free Earth for Ring Earth consisting as per Specification No.RDSO/SPN/197/2016 Ver 1.0 or latest & as per RDSO TAN letter No- RDSO-SIGEnB (GEN)/1/2020 dated 30.06.2025 or latest, bonding connections drawing no. SDO/RDSO/E&B/002. (a) Copper bonded steel electrodes of 3.0 m long, 17.0mm dia. minimum with copper bonding thickness of min 250micron and UL listed and marked-1 No. (b) Earth Enhancement compound of RDSO approved brand supplied in sealed bags of min 30-35 Kg.- 1 Nos. (c ) Copper Strip of 200mm x 25mm x 6mm to exothermically welded to Earth electrode- 1no.(d) Copper Strip of 300mm x 25mm x 6mm (MEEB) -1no.(e) Copper Strip of 150mm x25mm x 6mm (SEEB)- 1no. Inspection by RDSO for supply portion. | — | — | — | 86,26,972.64 | |
| — | 806.00 | — | — | ||
| Installation of Single Maintenance Free Earth pit as per RDSO Drawing No. SDO/RDSO/E&B/001 which includes the following:-a)Digging/Auguring/Boring of single earth pit of 100mm to 125mm dia. to the depth of approx.3 meter. b) Insertion of 3.0 meter electrode andpenetrating it minimum 150 mm by pushing gently with sledge hammer where the natural soil is assumed. (c) Filling of earth pit with Earth Enhancement Compound (EEC) in slurry form and back filling. (d) Carrying out exothermic weld connection on single earth electrode to a copper tape of 200 x 25 x 6 mm.(e) Carrying out exothermic weld connection on the copper tape of 200 x 25 x 6 mm on Earth Electrode for connecting two 35 Sq. mm cables for redundancy. (f) The exothermic welding material for bonding the earth system shall be procured from RDSO approved firms, which includes graphite modules, clamps, weld metal powders. (g) The dimension of the chamber will be of 300 x 300 x 300 mm (inside dimension) of RCC with 50mm thick and fine finish,Inspection chamber should be as per IEC62561-5 or latest. The top RCC cover size shall be 400mmX400mmX50mm. The date of testing and earth resistance value shall be written on the cover with black base with yellow paint. | — | — | — | 41,00,259.02 | |
| — | 9516.00 | — | — | ||
| Supply of 35 Sq. mm PVC insulated Single core Multi strands copper conductor (Red/Black/Green) as per IS: 694/2010 or latest, as per Specification No. IRS:S-76/89 or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection- RDSO | — | — | — | 20,43,846.48 | |
| — | 5670.00 | — | — | ||
| Supply of PVC conduit pipe rigid plain ended conduit size 1 inch(25 mm) IS:9537 (part-3) and 9537 (Part-1) 1980 with latest amendment ISI marked with minimum 1.2 mm wall thickness & one socket at every 3 meter pipe. Inspection- Consignee | — | — | — | 1,30,580.1 | |
| — | 568.00 | — | — | ||
| Digging a trench to a depth of atleast 0.5 meter and run the two 35 sq. mm earth conductor (procured against supply item) from Earth pit to MEEB. Routing and exothermic termination of two 35 sq. mm earth conductors in trench from earth pit to 300 x25 x 6mm MEEB, which is to be fixed inside the equipment room with two 60mm insulation studs. | — | — | — | 44,162 | |
| — | 3510.00 | — | — | ||
| Supply of 10 Sq. mm PVC insulated Single core Multistrands copper conductor (Red/Black/Green) as per IS:694/2010 or latest, as per Specification No. IRS:S-76/89or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection- RDSO | — | — | — | 3,21,551.1 | |
| — | 3510.00 | — | — | ||
| Routing and connecting all the equipment in the equipment/relay room to SEEB with 10 sq. mm copper cable using copper lugs with stainless steel nut and bolts and fixtures. The work includes laying and routing the copper cable in PVC / conduits/ inside floor and fixing them on wall/floor. | — | — | — | 1,74,657.6 | |
| — | 443.00 | — | — | ||
| Supply of 16 Sq. mm PVC insulated Single core Multistrands copper conductor (Red/Black/Green) as perIS:694/2010 or latest, as per Specification No. IRS:S-76/89 or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection- RDSO | — | — | — | 55,915.46 | |
| — | 443.00 | — | — | ||
| Routing and connecting of all the SPDs in the equipmentroom/SEEB to MEEB with 16 sq.mm copper cable using copperlugs with stainless steel nut andbolts. | — | — | — | 22,043.68 | |
| — | 270.00 | — | — | ||
| Supply of Main Equipotential earth bus bar (MEEB) Copper of size-300x25x6 mm. Inspection- RDSO | — | — | — | 2,04,384.6 | |
| — | 10.00 | — | — | ||
| Supply of surge protective device (SPD) life tester designed for on site testing of surge protection devices. It allows checking and indicating the health status of GDT/MOV based SPD of voltage range up to 1000V. It shall indicate the status of SPD by measuring its electrical parameters SPD tester shall be of reputed make. Inspection-RITES | — | — | — | 13,08,035.3 | |
| — | 1948.00 | — | — | ||
| Supply of 50 mm x 6 mm (GI Strip) Galvanised steel tape for inter connecting the earth pits. Inspection- RITES | — | — | — | 9,05,021.32 | |
| — | 1948.00 | — | — | ||
| Digging a trench to a minimum depth of 0.5 meter and laying 50x6 mm bare Galvanized steel tape (Interconnecting tape) connecting all the earth pits. Routing and laying 50x6 mm Galvanized steel tape connecting all the earth pits. Carrying out exothermic weld connections onall the earth electrodes to Galvanized steel tape of size 50x6mm for interconnecting the earth pits. It shall be ensured that the distance between any two earth electrodes shall be minimum 3 meter (length of the earth electrode) and max up to 6 meter (twice the length of the earth electrode) to avoid mutual resistance effects. This interconnecting tape shall also be covered with approximately 30 Kg of earth enhancing compound for each 3 meters length. Earth enhancement compound 10Kg along each meter also to be spreaded along the Galvanized steel tape. | — | — | — | 1,51,457 | |
| — | 2855.00 | — | — | ||
| Supply of Exothermic welding materials for connecting the existing ring earth with new maintenace free earth. (Cad weld or similar). Inspection- RDSO | — | — | — | 46,15,592.85 | |
| — | 2855.00 | — | — | ||
| Carrying out exothermic welding for various conductors as per requirement materials required for the work like, Lug, Nut screw, Bolt, welding material & other miscellaneous materials (excluding cable) required for the interconnection works to be supplied by contractor. | — | — | — | 11,13,450 | |
| — | 5095.00 | — | — | ||
| Supply of 25mm x 2 mm bare copper strips in the equipment room. Inspection- RDSO | — | — | — | 53,41,241.35 | |
| — | 5095.00 | — | — | ||
| Routing and termination of 25x2mm Copper tape/8 mm solid copper round conductor which is to be fixed inside the equipment room with 60mm, 6KVA insulation studs including supply of insulation studs. The separation of the two successive insulation studs hould be 600mm apart. | — | — | — | 3,96,136.25 | |
| — | 53070.00 | — | — | ||
| Supply of earth enhancement material for treatment of earth pits as per Specification No. RDSO/SPN/197/2016 Ver 1.0 or latest. Inspection- RDSO | — | — | — | 63,11,084.4 | |
| — | 2000.00 | — | — | ||
| Provision of Cement concrete enclosure for Earth electrode as per approved drawing RDSO Drawing No. SDO/RDSO/E&B/001. All the sundry materials to be supplied by the contractor. | — | — | — | 9,69,340 | |
| — | 10350.00 | — | — | ||
| Earth work for excavation and refilling around location boxes and signals etc. where necessary including 50M lead and 1.5M lift. The lead is to be measured from centre of gravity of location to the centre of filling and lift from main ground level. The earth work should be well rammed including breaking of clods, levelling and dressing etc. as per instruction of Engineer at site. | — | — | — | 16,93,570.5 | |
| — | 592.00 | — | — | ||
| Engaging mechanical excavators like JCB or other machineries for regarding and leveling the formation, Dismantling any infringing structures, clearing and removing debris etc., with all lead and lifts etc., complete and as per the instruction of railway representative at site. | — | — | — | 5,15,762.24 | |
| — | 4680.00 | — | — | ||
| Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer over the plastered wall surface toprepare the surface even and smooth complete. | — | — | — | 5,11,804.8 | |
| — | 1290.00 | — | — | ||
| Providing brick masonry in ratio 1:6 cement & mortar including plastering with 1:4 cement &sand mixture both side, 20mm thick each withcontractors own classII bricks including excavation, curing, grouting, bolting etc. wherever required. Bricks, sand & cement to be supplied by the contractor. | — | — | — | 22,78,152.9 | |
| — | 40000.00 | — | — | ||
| Loading, Leading & unloading of materials from store to another store as per instruction of consignee. All the material to be transported carefully without damage. Contractor have to do proper stacking of material and prepare list of material. | — | — | — | 2,22,800 | |
| — | 390.00 | — | — | ||
| Cement Concrete of proportion 1:3:6 (Cement: Sand: Stonechips of 25mm nominal size) for miscellaneous items. It includes excavation, ramming of CC by using vibrator, curing and plastering with cement and sandmixture (aggregate will not exceed beyond 3.8 cm). Note: All materials required for foundation are to be supplied by the contractor. | — | — | — | 11,78,751.6 | |
| — | 58500.00 | — | — | ||
| Fencing Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | — | — | — | 65,49,075 | |
| — | 1136.00 | — | — | ||
| Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/10 sqm) | — | — | — | 1,70,774.88 | |
| — | 1000.00 | — | — | ||
| Supply of Class C, Type 2 Protection for 60-100V AC/DC supply as per Clause No.3.12.3 of Specification No. RDSO/SPN/165/2023 Ver 4.0 Amendment-1 or latest. The Class II/C type shall be with pluggable type, with indication and potential free contact. The supplier should submit OEM certificate, KEMA, UL Certificate with the material, for connection between L1-L2, L1-E &L2-E. Inspection- RDSO | — | — | — | 7,86,040 | |
| — | 1000.00 | — | — | ||
| Supply of Class C, Type 2 Protection for 24-60VAC/DC supply as per clause No.3.12.3 of Specification No. RDSO/SPN/165/2023 Ver 4.0 Amendment-1 or latest. The Class II/C type shall be with pluggable type, with indication and potential free contact. The supplier should submit OEM certificate, KEMA, UL Certificate with thematerial, for connection between L1-L2, L1-E &L2-E. Inspection- RDSO | — | — | — | 7,86,040 | |
| — | 44.00 | — | — | ||
| Supply of Class B & C Surge protection Device (SPD) - Type I & II with Visual Indication and Potential free contact to remote monitoring as per Specification No. RDSO/SPN/165/2023 Ver 4.0 Amendment-1 or latest and IEC standard 61643 for Single line 230V AC application with handling Lightning surges of 10/350 micro seconds and Switching surges of 8/20 microseconds .One Set consists of 3 nos. of SPD (2 No. of B Class(L-N, N-E) and one no. of C Class (L-N) all enclosed in a Box with KEMA or VDE certified asper latest IEC 61643-11-2011 Standard. ClassB &C Surge protection device required with Three modules only. Inspection-RDSO | — | — | — | 2,32,745.48 | |
| — | 20.00 | — | — | ||
| Supply of Earth ground resistance leakage current tester (Clamp on ground resistance tester) similar to MECO make or similar , specification similar to model no. 4680BLC.Warranty: Minimum one year. Make:MECO, FLUKE, MEGGER, HIOKI,METRAVI or similar. Inspection-RITES | — | — | — | 6,94,980 | |
| — | 20.00 | — | — | ||
| Supply and testing of digital earth resistance tester model no. Motwane DET-20 or similar and better, 0.1/.01 ohm resolution, range 0-20 ohms. Inspection- Consignee | — | — | — | 3,86,379.8 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC_April-2022_1.pdf
ATTACHMENT
ACSGCC22-231to6.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipno7-10.pdf
ATTACHMENT
GCCACS11.pdf
ATTACHMENT
TD-01-2026-27Earthingarrangement02.04.2026_2.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .