Construction of Pharmaceutical Science and Technology Building of Madan Mohan Malviya University of Technology Gorakhpur Lot No 1 of 4

Amount

Excavation of Foundation- Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil DSR-2.6.1 (GST Shall be paid Extra)

Sand Filling- Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. (DSR-2.27) (GST Shall be paid Extra)

PCC Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) (DSR-4.1.8) (GST Shall be paid Extra)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement :4 coarse sand) DSR 6.1.2 (GST Shall be paid Extra)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate DSR 11.3.1 (GST Shall be paid Extra)

Providing & laying in position machine batched and machine. Mixed design mix M-25 grade cement concrete for reinforcement cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying excluding the cost of centering, shuttering , finishing and but excluding reinforcement , including admixtures in recommended proportion as per IS : 9103 to acclerate, retarder for setting of concrete/ improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note :- Cement content considered in this item @ 330 kg/cum. Excess or less cement used as per design mix is payable or recoverable separately. (R.C.C. work Upto Plinth Lvl.) (a) Footing, (b) Column, © Plinth DSR 5.33.1 (GST Shall be paid Extra)

Providing & laying in position machine batched and machine. Mixed design mix M-25 grade cement concrete for reinforcement cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying excluding the cost of centering, shuttering , finishing and but excluding reinforcement , including admixtures in recommended proportion as per IS : 9103 to acclerate, retarder for setting of concrete/ improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note :- Cement content considered in this item @ 330 kg/cum. Excess or less cement used as per design mix is payable or recoverable separately. (R.C.C. work ABOVE Plinth Lvl.) (a) Lintel , (b) Slab,© Beam, (d) Column DSR 5.33.2 (GST Shall be paid Extra)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete . Thermo-Mechanically Treated bars of grade Fe-500D or more. (a) upto plinth, (b) above plinth DSR 5.22.6 (GST Shall be paid Extra)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) DSR 6.1.2 (GST Shall be paid Extra)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) (DSR-6.4.2) (GST Shall be paid Extra)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) (DSR-6.4.1) (GST Shall be paid Extra)

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). (DSR-4.10) (GST Shall be paid Extra)

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. (DSR-4.13) (GST Shall be paid Extra)

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, erraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (DSR 22.7.1 ) (GST Shall be paid Extra)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with adjustable lugs with split end tail to each jamb DSR 10.14.1.1 ) (GST Shall be paid Extra)

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides DSR 10.29.2 (GST Shall be paid Extra)

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm, sash 67 x 80 mm , & mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension . (Area of window above 3.00 sqm upto 5.00 sqm). (DSR-9.147A.3) (GST Shall be paid Extra)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Float glass panes 6.0 mm thick glass panes (DSR- 9.7.7.2) (GST Shall be paid Extra)

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws DSR 9.21.1 (GST Shall be paid Extra)

Providing & fixing of Sliding door bolts (300x16mm) DSR 9.62.1 (GST Shall be paid Extra)

Providing & fixing of tower bolts (250x10mm) DSR 9.63.1 (GST Shall be paid Extra)

Providing & fixing of handle 125mm) DSR 9.66.1 (GST Shall be paid Extra)

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand) (DSR-13.5.1) (GST Shall be paid Extra)

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) DSR-13.4.2 (GST Shall be paid Extra)

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) DSR-13.4.2 (GST Shall be paid Extra)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm [DSR-11.41.2] (GST Shall be paid Extra)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm. D.S.R. 11.46.2 (GST Shall be paid Extra)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thickt DSR 11.26.1 (GST Shall be paid Extra)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - : 1:1.5:3 (1 cement : 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size) DSR - 4.1.2 (GST Shall be paid Extra)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. DSR 11.38 (GST Shall be paid Extra)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 sqm DSR 8.2.2.2 (GST Shall be paid Extra)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an evenshade Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture DSR 13.62.1 (GST Shall be paid Extra)

Finishing walls with Acrylic smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67ltr/10 sqm over the including base coat of water proofing cement paint applied @ 2.20 kg/10 Sqm. DSR 13.46.1 (GST Shall be paid Extra)

One priming coat of cement primer and two coats oil distemper on new work including supply of all materials, labour and tools and plants etc. required for proper completion of the work DSR 13.41.1 (GST Shall be paid Extra)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. D.S.R. 13.80 (GST Shall be paid Extra)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. DSR -4.17 (GST Shall be paid Extra)

Centering and shuttering including strutting, propping etc. and removal of form: in Foundations, footings, bases of columns, etc. for mass concrete DSR 5.9.1 (GST Shall be paid Extra)

as item number 39 in Suspended floors, roofs, landings, balconies and access platform DSR 5.9.3 (GST Shall be paid Extra)

as item number 39 in Lintels, beams, plinth beams, girders, bressumers and cantilevers DSR 5.9.5 (GST Shall be paid Extra)

as item number 39 in Columns, Pillars, Piers, Abutments, Posts and Struts DSR 5.9.6 (GST Shall be paid Extra)

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) DSR 9.22.1 (GST Shall be paid Extra)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter [DSR-12.41.2] (GST Shall be paid Extra)

Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories forunplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend [DSR-12.42.5.2] (GST Shall be paid Extra)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm [DSR-12.43.2] (GST Shall be paid Extra)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. [DSR-12.22] (GST Shall be paid Extra)

Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring ‘T’ with : D.S.R. 12.54.2 (GST Shall be paid Extra)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). D.S.R. 10.28 (GST Shall be paid Extra)

Providing & laying of light cinder filling under floor of toilets & other sunken roofs. MR (GST Shall be paid Extra)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.[DSR-22.5] (GST Shall be paid Extra)

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Including labour cess. (GST shall be paid extra) DSR-24.2 (GST Shall be paid Extra)

SANITARY INSTALLATIONS & C.P FITTINGS Providing and fixing water closet squatting pan ( Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS:7231, Parryware/Hindware/Seabird/Orient (Coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests 17.1.1 (GST Shall be paid Extra)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, Parryware/ Hindware/ Seabrid /Orient (Coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked black solid plastic seat and lid 17.2.1 (GST Shall be paid Extra)

Providing & fixing white vitreous china wash basin with C.I. brackets painted white, 15 mm C.P. brass pillar taps, C.P. brass chain with rubber plug, 32mm C.P. brass waste of standerd pattern including cutting & making good the walls wherever required. a)White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps 17.7.1 (GST Shall be paid Extra)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia 17.28.1.1 (GST Shall be paid Extra)

40 mm dia 17.28.1.2 (GST Shall be paid Extra)

Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. . 17.31 (GST Shall be paid Extra)

Providing and fixing white vitreous china flat back half stall urinal of size 580*380*350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in D.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required: Range of Single half stall urinals with 5 litre PV.C. automatic flushing cistern. 17.5.1 (GST Shall be paid Extra)

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade 8.10.2 (GST Shall be paid Extra)

Providing and fixing PTMT Bottle Trap for Wash basin and sink Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms 17.70.2 (GST Shall be paid Extra)

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 17.71 (GST Shall be paid Extra)

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms 17.73.2. (GST Shall be paid Extra)

CP Brass fittings Providing and fixing unplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore 18.21.2.1 (GST Shall be paid Extra)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 a) 15 mm nominal bore18.49.1 (GST Shall be paid Extra)

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. a) 15 mm nominal bore . 18.51.1 (GST Shall be paid Extra)

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore . 18.53.1 (GST Shall be paid Extra)

Providing and fixing C.P. brass shower rose with 15 or 20mm inlet 100 mm diameter 18.22.1 (GST Shall be paid Extra)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931: 15mm nominal bore 18.52.1 (GST Shall be paid Extra)

PVC PIPES & FITTINGS AND RAIN WATER PIPES Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC pipes by means of 50x50x50 mm hard wood plugs, screwed with MS screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm 12.43.2 (GST Shall be paid Extra)

Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size) around P.V.C Soil and waste pipe including bed concrete as per standard design(embedded in the flooring / ground) 100 /90 mm dia DSR no.19.2.1 (GST Shall be paid Extra)

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. 110 mm 12.41.2 (GST Shall be paid Extra)

Providing and fixing on wall face unplasticised PVC moulded fittings/acces.ies for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion. Bend 87.5 degree 110 mm Bend 12.42.5.2 (GST Shall be paid Extra)

Shoe (Plain)110 mm Shoe (GST Shall be paid Extra)

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 12.44 (GST Shall be paid Extra)

Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with MS screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm 12.43.2 (GST Shall be paid Extra)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete. 12.22 (GST Shall be paid Extra)

INTERNAL & EXTERNAL WATER SUPPLY WORKS Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 20mm dia nominal outer dia pipes 18.8.2 (GST Shall be paid Extra)

25mm dia nominal outer dia pipes 18.8.3 (GST Shall be paid Extra)

32mm dia nominal outer dia pipes 18.8.4 (GST Shall be paid Extra)

Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good walls etc. (internal work ).Internal work-Exposed on wall 25mm dia nominal bore 18.10.3 (GST Shall be paid Extra)

32mm dia nominal bore 18.10.4 (GST Shall be paid Extra)

40mm dia nominal bore 18.10.5 (GST Shall be paid Extra)

50mm dia nominal bore 18.10.6 (GST Shall be paid Extra)

Providing and fixing GI Union in GI pipes including cutting and threading the pipe and making long screws etc. complete (new work). 25mm dia nominal bore 18.46.3 (GST Shall be paid Extra)

32mm dia nominal bore 18.46.4 (GST Shall be paid Extra)

40mm dia nominal bore 18.46.5 (GST Shall be paid Extra)

50mm dia nominal bore 18.46.6 (GST Shall be paid Extra)

Providing and fixing gun metal gate valve with wheel of approved quality. 25mm dia nominal bore 18.17.1 (GST Shall be paid Extra)

32mm dia nominal bore 18.17.2 (GST Shall be paid Extra)

40mm dia nominal bore 18.17.3 (GST Shall be paid Extra)

50mm dia nominal bore 18.17.4 (GST Shall be paid Extra)

Providing and placing on terrace (at all floor levels)polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank.[Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license]. Capcity in Per Liters 18.48 (GST Shall be paid Extra)

SEWERAGE SYSTEM Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m. All kinds of soil Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm. 2.10.1.2 (GST Shall be paid Extra)

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 100mm diameter 19.1.1 (GST Shall be paid Extra)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design 100mm dia SW pipe 19.2.1 (GST Shall be paid Extra)

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 150 mm. dia. RCC Pipes 19.6.2 (GST Shall be paid Extra)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 150 mm. dia. RCC Pipes 19.3.2 (GST Shall be paid Extra)

Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 150 x 100 mm size P type With Sewer bricks conforming to IS : 4885 19.4.2.2 (GST Shall be paid Extra)

Supplying and fixing C.I.cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 Kg. 19.20 (GST Shall be paid Extra)

Providing and fixing 100 mm sand cast Iron grating for gully trap. 17.29 (GST Shall be paid Extra)

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design. 19.7 Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). With FPS bricks of class designation 75 (i) For Sewer Line 19.7.1.1 (GST Shall be paid Extra)

Extra for depth for manholes: Size 90x80cm with FPS bricks class I). 19.8.1.1 (GST Shall be paid Extra)

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm nominal size) as per standard design With 20x20 mm square bar 19.15.1 (GST Shall be paid Extra)

NON SCHEDULED ITEMS SANITARY INSTALLATIONS & C.P FITTINGS Providing and fixing in floor and wall face Ringfit UPVC ASTRAL ULTRADRAIN Conventional system for soil and waste water pipes conforming to (HSN CODE: 3917) Type B including jointing with seal ring. (i) Double socketed pipes. NSR a) 110mm dia P.V.C. pipe (GST Shall be paid Extra)

b) 90mm dia P.V.C. pipe (GST Shall be paid Extra)

COST OF SEWERAGE WORKS Excavating trenches in all kinds of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. up to 1.50 m depth Pipes 80 mm to 300 mm diameter 2.10.1.2 (GST Shall be paid Extra)

Open timbering in trenches including shuttering and shoring complete. (Measurement to be taken of the face area timbered) Depth not exceeding 1.5 meter 2.20.1 (GST Shall be paid Extra)

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 150 mm. dia. RCC Pipes (GST Shall be paid Extra)

Providing and laying cement concrete 1:5:10(1cement:5coarse sand :10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 150 mm. dia. (GST Shall be paid Extra)

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg).. With common burnt clay FPS (non modular) bricks of class designation 75 (i) For Sewer Line 19.7.1.1 (GST Shall be paid Extra)

Extra for depth for manholes: Size 90x80cm with With common burnt clay FPS (non modular) bricks of class designation 7.5 19.8.1.1 (GST Shall be paid Extra)

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay FPS (non modular) bricks of class designation 75 (i) For Sewer Line 19.7.3.1 (GST Shall be paid Extra)

Extra for depth for manholes: Size 90x120cm with With common burnt clay FPS (non modular) bricks of class designation 7.5 19.8.2.1 (GST Shall be paid Extra)

Providing orange colour safety foot rests of minimum 6 mm thick plastic encapsulated as per IS:10910 on 12 mm dia steel bar conforming to IS:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 19.16 (GST Shall be paid Extra)

COST OF EXTERNAL WATER SUPPLY WORKS Providing & fixing G.I. pipes complete with G.I. fittings including tenching and refilling etc. (external work) 65mm nominal bore. 18.12.7 (GST Shall be paid Extra)

50mm nominal bore. 18.12.6 (GST Shall be paid Extra)

25mm nominal bore. 18.12.3 (GST Shall be paid Extra)

Providing and fixing gate valve (with cap complete with bolts, nuts, rubber insertion etc. 65mm nominal bore 18.17.5 (GST Shall be paid Extra)

50mm nominal bore. 18.17.4 (GST Shall be paid Extra)

25mm nominal bore. 18.17.1 (GST Shall be paid Extra)

Constructing brick masonry chamber 600 x 600 x 750 mm inside with F.P.S. brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Sluice Valve / Air Valve, with C. I. surface box 100 mm top diameter, 160 mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20 mm nominal size); necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1 : 3 (1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design 18.33.1 (GST Shall be paid Extra)

Cost of Septic Tank & soakpit (GST Shall be paid Extra)

SEPTIC TANK Excavation in Foundation in ordinary soil (Loam clay, or sand) including lift upto 1.5 metre (5 fts.) and lead upto 30m (100 fts) & including filling, watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30 m. (100 fts) from the foundation trenches. (Rate is including Royality). (a) From 0.00 mt to 1.50 mt DSR-2.6.1 (GST Shall be paid Extra)

PCC Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) (DSR-4.1.8) (GST Shall be paid Extra)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand derived from natural sources : 3 graded stone aggregate20 mm nominal size derived from natural sources).As in item no. 3 above but for slabs (Using 1:1.5:3 Mix concrete) (DSR-5.3) (GST Shall be paid Extra)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.1.1 (GST Shall be paid Extra)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete . Thermo-Mechanically Treated bars of grade Fe-500D or more. DSR 5.22.6 A (GST Shall be paid Extra)

Cement concrete flooring 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement (25 mm thick floor). DSR-11.3.1 (GST Shall be paid Extra)

15mm cement plaster on rough side of mix 1:4 (1 cement : 4 coarse sand) [DSR13.5.1] (GST Shall be paid Extra)

Providing and fixing soil, waste and vent pipes : 75mm diameter : Sand cast iron S&S pipe as per IS: 1729 [DSR-17.35.2.1] (GST Shall be paid Extra)

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:(With 20x20mm square bar) [DSR 19.15.1] (GST Shall be paid Extra)

Making soak-pit 2.5 m. diameter and 3 m. deep with 45 x 45cm dry brick honey comb shaft with F.P.S bricks and SW drain pipe complete as per standard design. 19.32.1 (GST Shall be paid Extra)

Interlocking Work Excavation of Foundation- Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil (DSR-2.6.1) (GST Shall be paid Extra)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) (DSR-4.1.8) (GST Shall be paid Extra)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) DSR-6.1.1) (GST Shall be paid Extra)

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Chargee. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern(DSR 16.91) (GST Shall be paid Extra)

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) DSR-13.4.1 (GST Shall be paid Extra)

RAIN WATER HARVESTING RECHARGE PITS Earth work in exacavation in trenches for foundations and for pipes cables etc. in ordinary soil(loam clay or sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand disposal of surplus excavated earth as directed by the Engineer i/c with in a lead of 50m. (a) In all kind of soil upto 1.5m depth DSR-2.6.1

Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) and curing complete,including cost of form- work, in foundation and floors. (DSR-4.1.8) (GST Shall be paid Extra)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.1.1 (GST Shall be paid Extra)

R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-200. As in item no. 3 above but for slabs (Using 1:1.5:3 Mix concrete) DSR 5.33.2 (GST Shall be paid Extra)

P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. DSR 5.22.6 (GST Shall be paid Extra)

15 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 4 Coarse sand (DSR-13.5.1) (GST Shall be paid Extra)

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design: With 20x20mm square bar DSR-19.15.1 (GST Shall be paid Extra)

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 500mm internal diameter DSR-19.19.2.2 (GST Shall be paid Extra)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. Drilling of 300mm dia bore hole manually. DSR 23.2.1.1 (GST Shall be paid Extra)

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia DSR-23.4.2 (GST Shall be paid Extra)

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR-23.5 (GST Shall be paid Extra)

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR-23.6 (GST Shall be paid Extra)

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge. DSR-23.7 (GST Shall be paid Extra)

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. DSR-23.8 (GST Shall be paid Extra)

DESILTING CHAMBER Earth work in exacavation in trenches for foundations and for pipes cables etc. in ordinary soil(loam clay or sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand disposal of surplus excavated earth as directed by the Engineer i/c with in a lead of 50m. In all kind of soil upto 1.5m depth DSR-2.6.1 (GST Shall be paid Extra)

Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) and curing complete,including cost of form- work,in foundation and floors. (DSR-4.1.8) (GST Shall be paid Extra)

M-150 brick work in 1:4 (one cement and four coarse sand sand of 2.25 fineness modulus) mortar in foundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work. DSR 6.1.1 (GST Shall be paid Extra)

R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-200. As in item no. 3 above but for slabs (Using 1:1.5:3 Mix concrete) DSR 5.33.2 (GST Shall be paid Extra)

P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. DSR 5.22.6 (GST Shall be paid Extra)

15 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 4 Coarse sand (DSR-13.5.1) (GST Shall be paid Extra)

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design: With 20x20mm square bar DSR-19.15.1 (GST Shall be paid Extra)

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 500mm internal diameter DSR-19.19.2.2 (GST Shall be paid Extra)

DRAINAGE NETWORK Excavating trenches in all kinds of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. up to 1.50 m depth Pipes 80 mm to 300 mm diameter DSR-2.10.1.2 (GST Shall be paid Extra)

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 150 mm. dia. RCC Pipes DSR.19.6.2 (GST Shall be paid Extra)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 150 mm. dia. DSR-19.3.2 (GST Shall be paid Extra)

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat ement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of .class designation 7.5 DSR-18.33.1 (GST Shall be paid Extra)

ELECTRICK WORK Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. D.S.R 1.10.2 (GST Shall be paid Extra)

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required D.S.R 1.11 (GST Shall be paid Extra)

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 1x1.5 sqmm.for Inverter D.S.R 1.17.1 (GST Shall be paid Extra)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. D.S.R 1.31 (GST Shall be paid Extra)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/6 A modular switch, and 1 Nos. 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch connections etc. as required. (Computer Point) D.S.R 1.56 +1.32 (GST Shall be paid Extra)

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. . D.S.R 1.32 (GST Shall be paid Extra)

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. D.S.R 1.57 (GST Shall be paid Extra)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door D.S.R 2.4.2 (GST Shall be paid Extra)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 6 way (4 + 18), Double door D.S.R 2.4.2 (GST Shall be paid Extra)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door D.S.R 2.3.3 (GST Shall be paid Extra)

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole DSR 2.10.1 (GST Shall be paid Extra)

Double pole DSR 2.10.3 (GST Shall be paid Extra)

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. DSR 2.11 (GST Shall be paid Extra)

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps DSR 2.12.1 (GST Shall be paid Extra)

63 amps DSR 2.12.2 (GST Shall be paid Extra)

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 Amp, 16 KA, TPMCCB DSR 2.2.1 (GST Shall be paid Extra)

150 Amp, 16 KA TPMCCB DSR 2.2.3 (GST Shall be paid Extra)

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps DSR 2.13.1 (GST Shall be paid Extra)

63 amps DSR 2.13.2 (GST Shall be paid Extra)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2X 1.5 sq.mm+1X1.5sq. mm earth wire D.S.R 1.14.1 (GST Shall be paid Extra)

2X 2.5sq.mm+1X2.5sq. mm earth wire D.S.R 1.14.2 (GST Shall be paid Extra)

2X 4sq.mm+1X4sq. mm earth wire D.S.R 1.14.3 (GST Shall be paid Extra)

2X 6sq.mm+1X6sq. mm earth wire D.S.R 1.14.4 (GST Shall be paid Extra)

2X 10sq. mm + 1X 6 sq. mm earth wire D.S.R 1.14.5 (GST Shall be paid Extra)

2X 16sq. mm + 1X 6 sq. mm earth wire D.S.R 1.14.6 (GST Shall be paid Extra)

4X 10 sq. mm +2 X 6 sq. mm earth wire D.S.R 1.14.10 (GST Shall be paid Extra)

4X 16 sq. mm +2 X 6 sq. mm earth wire D.S.R 1.14.11 (GST Shall be paid Extra)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. D.S.R 5.6 (GST Shall be paid Extra)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. D.S.R 5.15 (GST Shall be paid Extra)

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. D.S.R 1.38 (GST Shall be paid Extra)

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing D.S.R Civil 10.18 (GST Shall be paid Extra)

Supplying, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor notless than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. D.S.R 19.1 (GST Shall be paid Extra)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. D.S.R 1.25 (GST Shall be paid Extra)

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep D.S.R 1.50.1 (GST Shall be paid Extra)

Supply of fresh air Fan 300mm 1-phase 1400 rpm,230/250 volts,50Hz. MR (GST Shall be paid Extra)

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. complete in all respect. including Lugs and Glands 35 sq. mm 3-1/2 core RA (GST Shall be paid Extra)

70 sq. mm 3-1/2 core RA (GST Shall be paid Extra)

150 sq. mm 3-1/2 core RA (GST Shall be paid Extra)

400 sq. mm 3-1/2 core RA (GST Shall be paid Extra)

Supply and fixing of 2'x2' 36Watt to 46 Watt, Indoor Recess/Surface mounting LED Square Fitting complete in all respect. RA (GST Shall be paid Extra)

Supply and Fixing of 10-15 Watt LED COB Light complete in all respect. RA (GST Shall be paid Extra)

Supply and fixing of LED tube light batten suitable for up to 1x20 watt LED Tube Light on surface 100 lm/watt, P.F>0.95,THD<10% at full load,CRI>80,sheet Thickness 0.8mm complete in all respect. RA (GST Shall be paid Extra)

Supply and Fixing of LED Bulb 9 Watt lumen 810 to 945 complete in all respect. RA (GST Shall be paid Extra)

Supply and Fixing of Bulkhead fitting upto 10 Watt lumen 1000 complete in all respect. RA (GST Shall be paid Extra)

Supply and fixing of single light wall bracket with opal glasspaint finishing up to 6 watt LED complete in all respect. RA (GST Shall be paid Extra)

Supply and Fixing of Lamp Base LED Mirror Light 11 Watt lumen 800 complete in all respect. RA (GST Shall be paid Extra)

Supply and Fixing of LED Street Light fitting having die cast aluminium body and diffuser with driver set suitable for 90 Watt confirming to IP 66 and above protection complete in all respect. 82500-9900 system lumens high power LED with lenses> 110 lm/watt, P.F.>0.95, THD<10% at full Load, CRI>70, potted driver set phase to phase protection at 440 V and >300 V, auto cut and restart feature with 5 Year warranty. RA (GST Shall be paid Extra)

S&F of 400 Amp. four pole change over switch on 50mm x 50mm x 6mm angle iron frame, including the cost of labour, T&P, painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in charge. MR (GST Shall be paid Extra)

Same as above item no. 40 but for INCOMING 200 Amp /415Volt MCCB-1 No, Outgoing 100 Amp MCCB-1 Nos. & 63 Amp MCCB-3 Nos. MR (GST Shall be paid Extra)

Supply and Installation of split type A.C 5 Star invertor Type Mistubishi (GR Series)/O-General (CETA B Series)/Toshiba (G3KCV Series) 2.0 Ton Capacity MR (GST Shall be paid Extra)

As above for 1.5 Ton Capacity MR v(GST Shall be paid Extra)

5 KVA Voltage Stablizer for Air Conditioner Upto 2TR (130 - 300 Range) Copper Winding. MR (GST Shall be paid Extra)

4 KVA Voltage Stablizer for Air Conditioner Upto 1.5TR (130 - 300 Range) Copper Winding. MR (GST Shall be paid Extra)

Supply of Out Door Unit stand for split type A.C MR (GST Shall be paid Extra)

SITC of suction/Discharge Copper pipe line in split A.C unit 1.5 ton capacity including brazing,nitrile rubber insulation 9mm thick class o etc comlete 1/4" (6.40mm) and 1/2" (12.70) MR (GST Shall be paid Extra)

SITC of suction/Discharge Copper pipe line in split A.C unit 1.8/2.0 ton capacity including brazing,nitrile rubber insulation 9mm thick class o etc comlete 3/8" (9.50mm) and 5/8" (15.90) MR (GST Shall be paid Extra)

S/I of heavy duty CPVC 20mm/25mm OD pipe for condensed water drain with clipping accessories complete. MR (GST Shall be paid Extra)

S & F of Door Closer MR. (GST Shall be paid Extra)

2.5sqmm 3 core Round cable for A.c Connecting indoor to unit to Stablizer/power point. MR (GST Shall be paid Extra)

2.5sqmm 4 core Round cable for A.c Connecting indoor/Outdoor MR (GST Shall be paid Extra)

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm Dia DSR 18.7.8 (GST Shall be paid Extra)

100 mm Dia DSR 18.7.7 (GST Shall be paid Extra)

80 mm Dia DSR 18.7.6 (GST Shall be paid Extra)

50 mm Dia DSR 18.7.4 (GST Shall be paid Extra)

25 mm Dia DSR 18.7.1 (GST Shall be paid Extra)

Supplying, fixing, testing & commission of butterfly valve of PN-16 slim seal standerd lever operated type as per design standerd IS:1395 or BS:5155 with required flanges, nut bolts etc. complete in all respects.c 100 mm dia DSR 18.11.5 (GST Shall be paid Extra)

80 mm dia DSR 18.11.4 (GST Shall be paid Extra)

Providing, installation, testing and commission of non-return valve of following sizes PN-10 as per design standerd IS: 5312 or BS:1868 with companion flanges, bolts, nuts, washers etc. complete in all respects. 100 mm dia DSR 18.14.5 (GST Shall be paid Extra)

80 mm dia DSR 18.14.4 (GST Shall be paid Extra)

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked completewith nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 150 mm dia DSR 18.12.6 (GST Shall be paid Extra)

100 mm dia DSR 18.12.5 (GST Shall be paid Extra)

80 mm dia DSR 18.12.4 (GST Shall be paid Extra)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m DSR 18.17.1 (GST Shall be paid Extra)

Supplying Installation testing & Commissioning of 25 mm Air Release valve gunmental having rubber ball and with 25 mm BSP threaded male inlet including necessary accessories and connections complete in all respect. MR (GST Shall be paid Extra)

Supplying Installation testing & Commissioning of SS/GM/Ball Valve 50 mm dia complete. MR (GST Shall be paid Extra)

SITC of Hose Box of 18 SWG MS Sheet with glass fronted door to accommodate 2 nos. RRL hose & 1 no. SS Branch Pipe with nozzle (External/ Internal) Size 800x600x400 MR (GST Shall be paid Extra)

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63mm dia male and female couplings duly bound with Gl wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel DSR 18.16.2 (GST Shall be paid Extra)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: Stainless Steel (Grade 304) DSR 18.18.2 (GST Shall be paid Extra)

(A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) 450 Ipm at 35 m Head DSR 18.4.2 (GST Shall be paid Extra)

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. DSR 18.2 (GST Shall be paid Extra)

Supply Installation testing and commissioning of Pressure Gauge. MR (GST Shall be paid Extra)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe DSR 18.19.2 (GST Shall be paid Extra)

SITC of Automatic panel of tarrace pump suitable for 5 HP tarrace pump. MR (GST Shall be paid Extra)

Supplying Laying testing & Commissioning of 2 core X 1.5 sq.mm single standard copper conductor, PVC insulated armored cable. DSR 17.5.2 (GST Shall be paid Extra)

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. complete in all respect. including Lugs and Glands 16 sqmm 4 core RA (GST Shall be paid Extra)

S/F of 200 AMP 4 pole changeover switch with angle iron frame complete. MR (GST Shall be paid Extra)

S/L of 1800mmX900mmX12mm thick chequered rubber matting of tested quality MR (GST Shall be paid Extra)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. DSR 5.6 (GST Shall be paid Extra)

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. DSR 5.14 (GST Shall be paid Extra)

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. DSR 18.22 (GST Shall be paid Extra)

Supplying and fixing single headed hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel DSR 18.9.2 (GST Shall be paid Extra)

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. DSR 17.2.4 (GST Shall be paid Extra)

Supplying, installation, testing & commissioning of intelligent addressable thermal (heat) detector with rate of rise cum fixed tempreature thermistor complete with base as required. DSR 17.2.9 (GST Shall be paid Extra)

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. DSR 17.2.5 (GST Shall be paid Extra)

Supplying Installation testing & Commissioning of Addressable Manual Call Point complete with base as required. DSR 17.2.14 (GST Shall be paid Extra)

Supplying Installation testing & Commissioning of Addressable horn cum strobe complete with base as required. DSR 17.2.15 (GST Shall be paid Extra)

Supplying Installation testing & Commissioning of fault isolator complete with base as required. DSR 17.2.7 (GST Shall be paid Extra)

Supplying Laying testing & Commissioning of 2 corex 1.5 sq.mm single standard copper conductor, PVC insulated armored cable. DSR 17.5.2 (GST Shall be paid Extra)

Supply & fixing of CO2 type fire extinguisher, 4.5 kg. capacity (ISI Marked IS:2878 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. MR (GST Shall be paid Extra)

Supply & fixing of fire extinguisher, ABC Type 4.00 kg. capacity (ISI Marked IS:15683 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. MR (GST Shall be paid Extra)

Providing and Fixing Self glow Exit signage for stairs and exits. Size 100 x 300 MR (GST Shall be paid Extra)

IP BASED HD CAMERA SITC of Indoor Hd bullet camera with IR with 1/2.8-inch CMOS, 4MP, Sensor pixels 1920 x 1080 with IR LED @ 20 mts, Sensitivity-0.011x (color), 0. 1x (mono), H.26 (MP): M-JPEG video compression, Motion, tamper, Dynamic range, White balance, BLC, Privacy Masking, Fixed 4.0 mm lens, with al necessary fixing accessories. MR (GST Shall be paid Extra)

SITC of Indoor dome camera with IR with 1/2.8-inch CMOS, 4MP, Sensor pixels 1920 x 1080 with IR LED @ 10mts, Sensitivity-0.01 1x (color), 0.01x (mono), 11.264 (MP): M-JPEG video compression, Motion, tamper and audio detection, Dynamic range. White balance, BLC, Privacy Masking, Fixed upto 3.0 mm lens, etc with all necessary fixing accessories. MR (GST Shall be paid Extra)

NETWORK VIDEO RECORDER Supply, installation, testing & commissioning of 24 channel Network Video Recorder with storage drive providing storage of 1 month. MR (GST Shall be paid Extra)

NETWORK COMPONENTS Single Port Face Plate on wall with neccesary fixing accessories. MR (GST Shall be paid Extra)

SITC of Cat 6 Patch Cords - 5M length at rack side MR (GST Shall be paid Extra)

SITC Cat 6 Patch Cords - 2M MR (GST Shall be paid Extra)

SITC of Cat-6 POE Patch Panel- Fully Loaded as per TiA /EiA Standard MR (GST Shall be paid Extra)

SITC of PoE 8 Port Gigabit Managed Switch with 2 SFP Ports MR (GST Shall be paid Extra)

Supplying, installing-testing and commissioning of Workstation PC: Intel(R) Core i7 11th Gen Processor Memory: 16 GB, NON-ECC, 1600MHZ; RAM: 16GB (1X16GB) Non-ECC DDR3 1600MHz SDRAM Memory: Keyboard: 12 function Keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20"TFT Monitor, Dual port Graphics Card 4GB ; Network interface card: Integrated Intel(R) 82579LM Gigabit Ethernet LAN 10/100/1000; Hard disk: 500GB SSD, Operating system: Windows 11 . (GST Shall be paid Extra)

Supplying- installing, testing and commissioning of Full hd 42" 4K LED Display Panel. (GST Shall be paid Extra)

ACTIVE COMPONENTS SITC of 24 port L2 10/100/1000 Base-T Fully managed switch, with 22 Nos autosensing 10/100/1000 Base-T port and 2 Nos Dual-personality SFP port, with all required accessories (GST Shall be paid Extra)

NETWORK RACK 09U Wall Mountable powder coted Rack with 5x5A Power Manager., 1 position fan, min 1 nos of shelf, Front Glass door with Lock & Key as respective floor WxDxH (600 x 450 x 635mm) (GST Shall be paid Extra)

24U, 600 X 1000 mm floor Mountable powder coated Rack with 6x5A Power Manager, 2 Horizontal Cable Manager, 4 position fan, min 3 nos of shelf, Front Glass door with Lock & Key at IBMS room. (GST Shall be paid Extra)

COMMUNICATION CABLE SITC of Cat 6 copper 23 AWG flexible shielded cable for communication in 25 mm dia steel conduit.(MR) (GST Shall be paid Extra)

Supply of 2KVA online UPS for CCTV Systems with 15 Minutes Backup (GST Shall be paid Extra)

SITC of Electrical 2x1.5 MM Power cabel with Switch /Socket and all component as required . (GST Shall be paid Extra)

D.G. SET-1 No. 125 KVA-D.G. SET (With CPCB-IV Norm), Supply, installation, testing & commissioning of 3-phase, 415 volt, 1500 RPM, 50 HZ, Diesel generator set with prime rating capacity of 125 KVA at 0.8 pf lagging diesel engine alternator set mounted on common base frame in outdoor type acoustic enclosure,battery, batter charger, return fuel cooler, anti vibration mounting pads including residential silencer, engine alternator,WITH AUTOMATIC MAINS FAILURE CONTROL PANEL SYSTEM , With DG synchronisation enable feature along with Electronic Governer and AUTOMATIC variable Voltage and frequency controller Atoaticsafties with accessories as per specification complete as required. Diesel engine shall conform to IS:10000 and alternator shall be self excited complete with AVR to IS:4722. Including Cost of Standard AMF Control Panel. Makes- KIRLOSKAR/CUMMINS/Mahindra /Equivalents, MR (GST Shall be paid Extra)

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cablerun shall be fixed on M.S. clamps etc. of suitable size oras directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 120 Sq mm 3/12 core RA (GST Shall be paid Extra)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. D.S.R 5. (GST Shall be paid Extra)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. D.S.R 5.15 (GST Shall be paid Extra)

Excavation in foundation in Ordinary Soil(lorm clay or Sand), Cement concrete with 4 cm. (1½") gauge Brick ballast, R.C.C. work, M 150 class brick work, 2.5 cm (1 thick 1:2:4 plain cement concrete floor, Miid steel or iron work in purl ins, Mild steel or iron in plain work, Providing and fixing precoated galvanised iron profile sheets and 12mm thick plaster with cement mortar for proper completion of the work. RA (GST Shall be paid Extra)

Supply, installation, commissioning and testing of 16/15 passengers capacity elevators machine room, etc., complete. Type of Elevator: Passenger Elevators Capacity of the Elevator 1088 kgs (16/15 passengers) Speed: 1.00m/s Number of floors to be served: Ground +First+ Second+Third Number of landing entrances: 4 Number of Landing: 4Travel distance: 15.00 m Size of Lift well available: 1900 mm x 2800mm Min. Lift pit depth available: 1600 mm Lift car inside: 1000mm x 2400mmx 2200mm lift car door finish: Stainless Steel Hairline finish Lift car finish for walls: Stainless Steel Hairline finish Type of car door: Automatic center opening Stainless steel hairline finish Type of landing door: Automatic center opening Stainless steel hairline finish Lift car ceiling & lighting: SS- Moonlight Automatic Rescue Device (GST Shall be paid Extra)