CERTAIN REPAIRS TO GARRAGES CAR SCOOTER CYCLE PARKING SHEDS ROLLING SHUTTERS AND STEEL WORKS PLINTH PROTECTION AND ALLIED REPAIR WORKS AT MILIT AND DIAT GIRINAGAR PUNE 25

Amount

Demolition of stone/boulder ashlar facings, dressed stone work, precast concrete articles and precast concrete block walling built in cement mortar complete all as specified and directed.

M & L for Pre cast cement concrete block masonary with solid blocks exc 10 cm in width and setting in CM 1:6 with Type B1 1:3:6

M&L walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortor 1:6 complete all specified and directed.

All as item no03 above but except stone

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge n.exc 20mm and dressing face beds and joints as specified to random rubble walling brought upto courses complete all specified and directed.

Racking out joints/pointing to to random rubble masonary uncoursed built in CM or cement lime mortar complete all specified and directed.

M & L for Keyed pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1: 4 complete all specified and directed.

M & L for providing precast cement concrete 1:2:4 (12.50 mm greded agrregate) louvres and jallies set in cement mortor 1:6 ,25 mm thick (measured solid) including all moulding but excluding frame .

Taking down plastering in cement mortar on brick or stone wall etc including racking out joints hacking for key scrubbing down with water etc.

M&L for rendering 20mm thick on stone masonary work in cement mortar 1:4 finished fair and even without using extra cement complete.

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate in cills, steps, bands, copings, bed plates, blocks for inserting hold fasts etc. and the like including weathering, slightly rounded or chamfered angles and throating complete all specified and directed.

Supply only WPC of ISI marked.

M&L Applying two coat of apex exterior emulsion (Apex ultima or equivalent) over a coat of primer on wall surfaces including perpartion of new plaster surfaces on walls complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coat of apex exterior emulsion (Apex ultima or equivalent) over a coat of primer on wall complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any postion as in of chjjas parapet walls and similar works complete all as specified and directed.

M &L for formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished flat concrete surface up to 7.0 Mtr height complete all as specified and directed.

Material and labour for mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified.

M &L for reinforced cement concrete (nominal mix) type B1 1:2:4 using 20 mm graded stone aggregate as in chajja complete all as specified and directed

Demolition of cement concrete of any description and any position not otherwise specifically provided for

M&L cement concrete type D-2 1:4:8 (40mm graded aggregate) as in subbase 100 mm Thick

M&L cement concrete type B-1 1:2:4 (20mm graded aggregate), finished cement concrete even and smooth without using extra cement and using vaccum dewatering method i.e. Tremix flooring 100mm Thick

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade `B' in 100 mm thick concrete slab

M&L cement concrete type D-2 1:4:8 (40mm graded aggregate) as in subbase 75 mm Thick

M&L Chequered cement concrete tiles 30 cm X 30 cm X 25 mm thick set jointed and pointed in neat cement slurry in floor with grey cement and pigment including 15 mm thick screed bed cement mortar 1:6

M&L for rubber molded Machine pressed precast cement concrete interlocking paver block glossy finish any colour any shape and size confiring to IS 15658-2006 of 60mm Thick, M-35 Grade

M&L for thick sand cushioning below paving block

M&L For cement concrete Type B1 (1:2:4) in kerb or mud stop rounded or champhered on edge.

M&L Steel ventilator with top hung shutter including hinges, steel peg stay, complete

M&L for sheet glass ordinary quality 4 mm thick fitted with beeding/putty n.exc 0.5 sqm each all as directed by Engr-in-Charge

Roughening surfaces of old concrete floor by picking sweeping cleaning & washing down with water to remove dust etc incl removal of old treatment of any description and applying one coat of neat cement slurry @ 3.00 Kg/Sqm complete all as directed by Engr-in-Charge.

M&L for Cutting grooves in brick wall, 75 mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3

PCC (1:2:4) type B1 using 20 mm graded aggregate as in padding (level course) on roof 40 mm thick (average).

Screeding 10 mm thick in CM (1:4) using water proofing compound as per manufacturer instruction over roof and chajjas finished smooth complete all as directed by Engr-in-Charge. Note : Water proofing compound will be measured and paid separately.

Supply only integral water proofing compound.

M &L for APP based polymeric membrane minimum weight 3.5Kg/Sqm and minimum 3mm thick reinforced with polyster non -eoven fabric (wt not less than 150gms/sqm ) laid over primed surface with bituminious primer confirming to IS 3384 @ 0.3 lit/Sqm as per IS 3384 and finishing with preventive coat (two coats) with aluminium paint over a coat of hot blown bitumen 85/25 grade @ 1.2 kg per sqm.

Taking down carefully hood and steel rolling shutter of size exceeding 15 Sqm & not exceeding 50 each and refixing in the same opening after cleaning of guide rails,laths, top cover by kerosene and proper greasing, oiling, replacement of rusted nut, bolts etc, removing of bend, alignment etc to make the system smooth functional & making good the disturbed surfaces all as directed by Engr-in-charge. NOTE :- (i) Quoted rate shall be inclusive of providing missing nuts, bolts, greasing, oiling, denting, tension to spring etc.

M&L for repair to rolling spring, steel rolling pipe complete set with hoods including welding work etc all as directed by Engr-in-charge.

M&L for replacement of MS handles 150mm long including necessary fixing & welding work.

M&L for repair to locking device cleat of rolling shutter all as directed by Engr-in-charge.

M&L for replacement of 1.00mm thick MS laths of continuous single piece section without any welded joint, of steel rolling shutter, the lath section shall be rolled so as to have inter locking coils at both edges & deep corrugations at the center with average depth of not less than 12mm & each alternate lath section shall be fitted with malleable cast iron or mild steel clips securely riveted at either ends complete including painting with two coats of synthetic enamel paint over one coat of red oxide primer all as directed by Engr-in-charge.

Taking down existing steel rolling shutter of any size and type and S&F factory made steel rolling shutter with laths of thickness 1.00 mm without ball bearing as specified including top cover anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete, push pull or manual type complete confirming to the requirement of IS 6248-1979 all as specified & directed

Dismantling structural steel work including door, gate, windows excluding framed tresses etc

M&L for framed work as in doors, gates of angle fe -410 gde E 250 qureed section with gussed plates, mild steel plain black sheet any thickness complete drilled or welded to be prepared for hanging or sliding with and including either hooks and hinges all as directed by Engr-in-Charge.

S & F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

S & F structural steel MS work in tubular trusses /columns/railing work incl special shaped washer etc. complete with butt welded tubes complete all as spfd.

Preparation of new steel surfaces over 10 cm in width or girth and applying two coats of Synthetic enamel paint over a coat of red oxide primer .

S&F for Collapsible steel gates, top hung,consisting of channel pickets, pivoted flat bars, top and bottom runners, brasshandles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

S&F in repairs steel windows with side hung shutters including box type hinges including locking arrangements and peg stay complete with glazing bars dovetailed or welded.

Preparation of old painted surfaces of steel & Iron of any description any size any shpae or girth and applying one coat of synthetic enamel paint (1st quality) all as specified and directed by Engr-in-Charge.

M & L for 75 mmthick PCC 1:3:6 type C-1 with using 20 mm graded stone aggregate as in plinth protection,finished surfaceeven & smooth without using extra cement complete all as specified & directed.

Dismantling Pre-painted galvalume sheet (corrugated, semicurrguaged etc) sheet as in roof covering. Note :- Work will be carried up to 12 M height. Rate should be coated necessary scaffolding for applicable scheduled items.

Dismantling valley gutters plain steel sheets of any gauge/ thickness as in roof covering including naintal or Similar pattern roof covering. Note :- Work will be carried up to 12 M height. Rate should be coated necessary scaffolding for applicable scheduled items.

Hacking out old broken glass from steel / metal frame. Note :- Work will be carried up to 12 M height. Rate should be coated necessary scaffolding for applicable scheduled items.

Fixing only Pre-painted galvalume sheet of roof tile pattern/ any pattern approved by GE ( aluminium,Zinc and silicon coating) GI based, minimum thickness 0.45 mm of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall , fixed with self tapping screw including ridges and crimp eaves as directed by Engineer-in-Charge.

S& F 1.25mm plain galvanised , mild steel sheeting in valley gutter drip and straight flashing length and girth as fixed Note : Sheet should be joint with proper gas welding and applicable leakage test should be done on presence of Engineer-in-charge.

S&F MS clamps , hold fasts, wall ties as per specified and directed.

S&F rough cast wire glass 6.4mm thick exc 1.00 sqm but not exc 1.50 Sqm in size , fixed with metal boards , metal panel pins .

Fixing only Figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) Note :- Work will be carried up to 12 M height. Rate should be coated necessary scaffolding for applicable scheduled items.

M&L in repairs 160 mm bore PVC (SWR) pipes type ‘A’, single socketed, in any length with rubber ring joints fixed to walls.

M&L in repairs 160 mm bore PVC (SWR) bend type ‘A’, any radius.

M&L in repairs 160 mm bore PVC (SWR) bend type ‘A’, any radius with oval access door.

Taking down shutters of any description n. exc. 2 sqm each.

M&L for second class hard wood for plain solid, straight chowkats and frame rebated on the solid, rounded or chamfered put together with glue pinned at joints all as directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type both sides (ISI marked) all with 6 mm thick teak wood edging all round.

S&F 30 mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a), supplied and fitted to chowkats.

M&L for preparation of new wooden surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F 150 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed

S&F butt hinges, medium weight, cold rolled, mild steel of size 100mm.

S&F extruded aluminium alloy handles, fabricated type, anodized of size 150 mm.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash on wall. All as directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staples

M&L for removing plant growth any type and in any position by injection with chemical glyphosphate solution (4% concentration) at 20ml or till refusal by making cut or injecting in stem of plants or roots at 30mm , shall then be sprayed with solution 25ml glyphosphate (4% concentration diluted with 1 Ltrs of water).All roots/ plants shall be removed completely and making good the disturbed surfaces and painting with a coat of cement paint or acrylic paint to match existing finishes, complete all as specified and directed. (Note: (a) Work will be carried up to 16 M height. Rate should be coated necessary scaffolding for applicable scheduled items. .

Santosh Pandurang Pise

J.G.Goel

sagar construction

DHANESH PRAVIN GANDHI