Supply of Machinery at Govt.ITI, Gurugram

Amount

A) Pneumatic Trainer kit, each consisting of the following matching components and accessories :- (i) Single acting Cylinder Specification: Max. stroke length 50 mm, Bore dia 20mm-1 no. (ii) Double acting cylinder Specification:Max. stroke length 100 mm ,Bore dia 20mm ,magnetic type -1 No. (iii) 3/2-way valve Specification:manually-actuated, Normally closed- 2nos. (iv) 3/2-way valve Specification: pneumatically-actuated, spring return- 1 No(v) One-way flow control valve Specification: Operating pressure 6mpa(60 bar) max. premiciable pressure 12mpa (120 bar)- 2 Nos (vi)5/2-way valve specification; with manually- operated switch- 1No. (vii) 5/2-way valve specification: pneumatically-actuated, spring return- 1No. (viii) 5/2-way pneumatic actuated valve Specification: double pilot- 1No. (ix) 3/2-way roller lever valve Specification:direct actuation Normally closed- 2 Nos. (x) Shuttle valve (OR) Specification:normally inserted- 1 No. (xi) Two-pressure valve Specification:made of good quality- 1 no. (xii) Pressure gauge Specification: 0-16 bar- 1 No. (xiii) Manifold with self-closing Specification:NRV, 6-way- 1 No. (xiv) Pushbutton station for electrical signal input Specification:with 3 illuminated momentary-contact switches (1 NO + 1 NC) and 1 illuminated maintained- contact switch (1 NO + 1 NC ), contact load 2A- 1 No. (xv) Relay station Specification:with 3 relays each with 4 contact sets (3NO +1 NC or change -over type) , 5A- 1No (xvi) 3/2-way single solenoid valve Specification:with LED- 1 no (xvii) 5/2-way single solenoid valve Specification: with manual override and LED- 1 no. (xviii) 5/2-way double soleniod valve Specification: with manual override and LED- 1 No. (xix) Power supply unit Specification: Input voltage 85 - 265 V AC, Output voltage 24V DC , output current max. 4.5 A , short -circuit-proof – 1 no. (xx) Profile plate, Anodised, Aluminium Specification: 1100x700 mm, with carriers , mounting frames and mounting accessories ( To be fitted on the pneumatic workstation) - 1 set B) Pneumatic Workstation with 40 MM square aluminium profile legs, drawers surface and one pedestal drawer unit having 5 drawers each with handles and individual locks, on metalic full panel drawer slide Specification: (1) Work Table -Size (approx.) L 1200mmx W 900mm x H 900mm with four castor wheels including two lockable wheels at front side , (2) Drawer size Aprox. L 460mm x W 495 x H 158mm each , and over all size of drawer unit Aprox. L 470mm x W 495mm x H 825mm (3) Drawer slide height aprox. 85mm Make- Standard Make, Qty.- 1 No. C) Carrier for mounting components, such as PB & ray bouxes Specification: Made of good quality , Qty.- 1 No. D)Cut section models of pneumatic components. Specification: cut section models of pneumatic components mounted on a display board of suitable size.(Cut Section of Minimum 10 pneumatic components) , Qty.- 1 set

A) Hydraulic Trainer Kit, each consisting of the following matching components and accessories: (i) Hydraulic Power pack specification: with (1) external gear pump having a delivery rate of 2.5 lpm, (approx.) @ 1400 rpm operating pressure 60 bar, coupled to a single-phase AC motor (230 V AC) having start capacitor and ON/OFF switch and overload adjustable from 0 - 60 bar, (3) oil reservoir, ≥5 litres capacity having sight glass, drain screw, air filter, and P and T ports- 1 No. (ii) Pressure relief valve specification:pilot-operated- 1No. (iii) Drip tray, steel specification: size 1160 mm x 760 mm- 1 No. (iv) Pressure Gauge specification: Glycerin-damped, Indication range of: 0 - 100 bar- 1 No. (v) Four-Way distributor specification: with five ports, equipped with a pressure gauge- 1No. (vi) Double acting hydraulic cylinder specification: with a control cam, Piston diameter16 mm, Piston rod diameter10 mm, Stroke length 200 mm.-1 No. vii) Suitable Weight for specification: vertical hydraulic cylinder-1 No. (viii) Mounting kit for weight specification:for realizing pulling and pushing load- 1 No. (ix) 3/2-way directional control valve specification: with hand lever actuation- 1 No. (x) 4/2-way directional control valve specification: with hand lever actuation- 1 No. (xi) 4/3-way directional control valve specification:closed-centre position, with hand lever actuation.- 1 No. (xii) Non-return valve specification: Pilot operated- 1 no. (xiii) Pilot-operated check valve specification:pilot to open.- 1 No (xiv) One-way flow control valve specification:with integrated check valve.-1 No. (xv) T-Connector with self sealing coupling nipples (2 Nos.) and quick coupling socket (1No.)specification: Pilot operated- 2 Nos. (xvi) Profile plate,specification: Anodised Aluminium, 1100x700 mm, with carriers, mounting frames and mounting accessories (To be fitted onto the Hydraulic workstation)- 1 set B) Hydraulic Workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide specification:(1) Work Table - Size(Approx.) L1200mmXW900mmXH900 mm, with four castor wheels including two lockable wheels at the front side, (2) Drawer - Size (Approx.) - L460mmxW495mm xH158mm each, and overall size of Drawer unit (Approx.) - L470mmxW495mmxH825mm (3) Drawer slide height (Approx.) 85mm., Standard make qty- 1 no C) Cut-section models for hydraulic components specification: cut section models of hydraulic components mounted on a display board of suitable size. (cut section models of minimum 06 hydraulic components),qty-1 set

HARSH TRADERS

NiYo Engineers