civil work

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with Crushed Stone sand filling in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with Stone Dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting steel centering for sides and soffits including supports and strutting upto 3.29m height for plane surfaces such as RCC floor slab, roof slab, rectangular, square tee or ell beams, lintels, staircase, waist slab, landing slab, landing beam, portico slab, portico beams in all floors with all cross bracings using mild steel sheets of size 90cmX60cm and 10 gauge stiffened with welded mild steel angles of sizes 25mmX25mmX3mm for boarding laid over silver oak joists of size 10x6.5cm spaced at about 90cm centre to centre suppported by casurina props 10cm to 13cm dia spaced at 75cm centre to centre etc. complete complying with standard specification and as directed by the departmental officers.

For Plane surface such as RCC floor slabs, roof slabs, rectangular beams, Tee beams, Ell beams, lintels, landing slabs, waist slabs, canopy slabs etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing in position, Standardised Concrete Mix M-20 Grade in accordance with IS 456-2000, using 20mm and down graded hard broken granite store jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ration of 0.55, including admixture (plasticiser/Super plasticiser) in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improveworkability without impairing strength and durability with about (5 cu.m.) 7730 kg of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc., and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of mateials).

For Foundation and basement

In Ground Floor

In First Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc., complete complying with standard specification. and as directed by the departmental officers. (Contractor has to make his own arrangements for the supply of steel and binding wire).

Construction of Brick work in Cement Mortar 1:5 (one cement and one sand) using best quality of Second Class Ground Moulded Chamber Burnt Bricks 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

For Foundation and basement

Construction of Brick work in cement mortar 1:6 (One cement and six sand) using using best quality II class Ground moulded chamber burnt bricks of size 9" x 43/8"x 2 3/4"in for foundation andbasement and super structure,complying withstandard specification including curingetc complete as directed by the departmental officers.

For Foundation and basement

S.S. in Ground Floor

Construction of brick partition walls of following thickness using best quality II class ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2 3/4" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately).

S.S. in Ground floor (11.50cm)

S.S. in Ground floor (7cm)

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers.

Paving the floor with best quality double charged Vetrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M-sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK which has to be got approved by Executive Engineer before use on works)

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Self Designed Colour Ceramic Tiles

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Dadooing with printed design colour glazed tiles of size 300mm x 200mm x 6mm

Supplying and fixing of PVC rain water down fall pipes with new best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110mm dia

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special Ceiling Plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.

Supplying and applying of Two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the departmental officers. (The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet) cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc., complete). The putty should be got approved by the Executive Engineer before use on work.

Plastering with Cement Mortar 1:3 (One cement and three sand), 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihging, curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing fine polished cuddapah slab of 38/40mm thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

Supplying and fixing steel doors with the following specification, MS Angle of size 40 x 40 x 6mm at 3.5 Kg / m are used for outer frames and MS Angle of size 35 x 35 x 5mm at 2.6 Kg / m for the shutter frames. Stiffeners with MS Flat 32 x 6mm at 1.50 Kg / m is provided for fixing the aldrop for the door and welded intact 18 gauge CR Sheet is laid as panel in the shutters and welded intact of 1/3 bottom portion of the shutters, 2/3 portion at top provided with MS Grill at 20 Kg / m2 as per design and laid as panel in the shutters. Necessary 'J' section having MS Angle 46 x 25 x 3mm at 2.38 Kg /m is provided in between MS Grill and CR Sheet for compact fixing of the grill and sheet in position. The design and style for the upper panel shoule be approved by the departmental officers. MS Flat 18 x 5mm at 0.7 kg / m is welded as additional stiffeners at the rear side of the shutter in the bottom panel for strength and durability. MS Flat 32 x 3mm at 1.10 Kg / m is provided over the edge of one shutter in case of double door, to conceal the gap between the shutters. and 4 Nos. of hinges in double leaf doors are provided at an appropirate place in the outer frame. 6 Nos. of hold fasts of 200mm in length spliced at the ends are welded to the outer frame of the door. Tower bolts 2 Nos. one at top and the other at the bottom are provided. In case of double leaf door one number aldrop is provided at an appropirate place in the doors; two numbers aldrop in single leaf door. A tie bar is provided at the bottom of the outer frame to prevent twistng of frame during transportation or fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, taxes, transportation to site of work, loading, unloading and all other incidental charges, etc., complete.

Single Leaf

Double Leaf

Supplying and fixing the Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Supplying and fixing in position of steel windows with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 Kg/m and mullion 'J' section (F4B) of size 46x25 x 3mm at 2.28 kg/m and shutter section of made of F7D of 33 x 25 x 3mm at 1.419 Kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS flat at 0.70 Kg/m at 3 Nos. for each shutter and additional diagonal stiffeners of the same MS Flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR sheets in position firmly.4 numbers of sturdy hinges and Two number of handle-cum-latch of special type made with 18x5mm MS Flats are revetted to the shutters at an appropriate height in window. Suitable opening is left for its easy operation. A stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. Each window shutter having an adjustable stay made out of 18x5mm at 0.70 kg/m MS flat of length 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 120mm length spliced at the nds are welded to the out frame of the window by using MS flat of 18x5 mm at 0.70 kg/m, welded to the shutter at two place equivalent from each other from top and bottom of the shutter. An MS square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge to edge between them. All members are painted with one cat of anti-corrosive red oxide primer as directed by the departmental officers. All sections should be in confirmed with IS7452/1990. The cost includes cost of all materials, labour charges and other incidental charges, etc., complete.

Three Leaves

Supplying and fixing ventilator with new one of 'N' type ventilators using M.S angles of size 25x25x5mm for frame and M.S. tee of size 25x25x3mm M.S flat of size 20x3mm for fixing the weld mesh. special type of Hold fast welded to the frame of 45 degree inclined to wards centre for wall and fixing the weld mesh fixing the 4mm thick glass pans with necessary olipa and puttios, with required bolts, nuts and washers and one coat of red oxide primer etc. including necessay dismantling making holes in RCC columns, beams masonry whereever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by departmental the extent required and made good to the original contions after fixing as directed by departmental officers.

Supplying and fixing 40mm dia GI pipe for staircase handrails including labour charges for cutting, welding and fixing with MS flats etc. as directed by the departmental officers.

Supplying and fixing GI sheet 30cm wide and 1.6mm thick of best approved quality with required size with curved shape and white ridge sheet with necessary bolts and nuts bitumen washers, including cutting the sheet to the required size found necessary during execution etc., Complete complying with standard specifications. [The sheet should be got approved by the Engineer incharge before use on works]

Supplying and fixing in position steel balustrades using 20mm square rods spaced at 150mm centre to centre so that the two balustrades in each step shall be placed centrally and the top of balustrades connected with the hand rails (cost of hand rail shall be measured and paid separately) by means of MS flats of size 40mm x 6mm in the groove 40mm x 6mm provided at the bottom of hand rail; the bottom of balustrades shall be fixed on to the top of step concrete. An additional MS flat of size 50mm x 6mm shall be provided at the centre of balustrades connecting all square rods to the entire length including cost of square rods, flat and applying one coat of red oxide primer to the iron surfaces, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing M.S.Grills for Gate of approved design for open countryard, grill, grill work to doors and window openings etc. using necessary mild steel flats for inner and outer members which should be fixed on edges including cutting the members, welding, grining, one coat of priming coat using best approved quality red oxide primer, dismantling of walls / concrete if necessary, fixing and finishign the dismantled portion to oringinal condition etc. complete complying with standard specification as directed by departmental officers.

Painting the walls with two coats of cement paint over one coat of cement primer as instructed by the departmental officers including preparation of surface curing, etc. complete in all floors complying with standard specifications and as directed by the departmental officers. (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work)

Painting the walls with two coats of oil bound distember including cost for distemper, primer, cleaning and scraping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work).

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings..... such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing in position best quality and approved make of white colour (without Pedestal) wash hand basin of size 550x 400 mm necessary cast iron bracket 15mm dia chromium plated pillar tap 32mm dia 'B' class G.I. Waste pipe 32mm chromium plated brass waste coupling with rubber plug and chain 15mm dia nylon connection etc. complete including fixing the wash hand basin in position including cost of teak wood plugs screws rubber washer, white lead and giving water supply connection, testing for leakage etc. complete complying with standard specification. (The wash hand basin should be got approved by the Executive Engineer before use on work).

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc, complete complying with standard specifications and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on works).

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks).

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing Stainless Steel Sink of size 600x600x200mm including fixing in position etc., complete.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq/cm. pressure BIS mark and proving leak proof joints using PVC adhesives including fixing to the walls with special PVC / MS clamp, teak wood plugs, brass screws, etc, and making connection to all sanitary fittings, dismantling masonry / RCC works whereever found necessary and making the good dismand giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. as directed by the departmental officers (The PVC specials should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level.

75mm dia

110mm dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

75mm dia PVC Elbow

75mm dia PVC Tee

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia PVC Plain bend

75mm dia PVC Plain bend

Supplying, laying and jointing PVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. (Above Ground Level) (Internal Water supply)

32mm dia PVC Pipe

25mm dia PVC Pipe

20mm dia PVC Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

32mm dia Tee

32mm dia Elbow

32mm dia Bend

32x25mm dia Reducer

25mm dia Tee

25mm dia Elbow

25mm dia Bend

25x20mm dia Reducer

20mm dia Elbow

20mm dia Tee

20mm dia Bend

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc, complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on works.

32mm dia Gate valve

25mm dia Gate valve

20mm dia Gate valve

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position Health faucet of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specifications. (Taps should be got approved by Executive Engineer before use on works).

Drilling of borewells any where in Kancheepuram and Tiruvallur district including transportation from one place to another in alluvial soil sedimentary strata of clay and sand stone, shale pebbles, boulders,etc. byfirst taking a pilotbore of 140/150/200mm dia and theenlarging to required diaby direct or reverse rotarymud circulation method, usingfuel, labour drilling andwater required for drilling at the siteshown by theofficers including construction of mud pit (water available within a lead of 1.5KM) etc.complete and as directed by the departmental officers. upto 60m

Borewell 0 to 60m

Reaming from 140/200mm dia pilot bore to 300mm diabore asdirected by the departmental officers.upto 6M depthending below Ground level.

Borewell 0 to 60m

Supply of 160 mm PVC Special Blue casing pipe of best approved quality etc complete as directed by the departmental officers. The pipe should got approved by the Executive Engineer before use on works.

Without slot

With slot

Labour charges for inserting 165mm dia PVC casing pipes assemble (with slots or without slots) in the drilled hole including jointing the pipes with PVC coupler and with cement paste etc. complete as directed by the departmental oficers and supporting and packing the annular space with pebbles of size and quality is approved by the Executive Engineer. The conveyance charges to work site to be borne by the contractor.

Charges for developing the borewell for entire depth with suitable air compressor of 300 CFH capacity (minimum 8hrs) including transportation labour and fuel charges for compressor and directed by the departmental officers and conducting yield test by "V" notch methods.

Supply and fixing of HDPE Hose of 40mm dia for submersible pump including fixing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting in position of 3HP/3 phase of approved brand Submersible Pump with accessories of starter, Main Switch, Panel Board etc. complete to suit the need (The pump set should be got approved by the EE before supply)

Supplhying and fixing of 20mm dia Nylon rope for submersible motor of approved quality in etc complete complying with standard specification and as directed by the departmental offices.

Supplying and fixing the P.V.C. end cap of 160 mm dia at the end of P.V.C. casing pipe etc., complete complying with standard specification. The bore cap should be got approved by the Executive Engineer before use on works

Supplying and erecting in position of 3HP/3 phase of approved brand Submersible Pump with accessories of starter, Main Switch, Panel Board etc. complete to suit the need (The pump set should be got approved by the EE before supply)

Supplying and fixing of PVC water tank 1000 litres of ISI brand of approved quality and including cost of materials trasportation to site and necessary Brick work and Plastering for embedding the water tank, the Brick work and plastering measured and paid seperately to the relevant items as directed by the departmental officers.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC concealed light / fan Point (for electronic regulator) (5 points per coil) (SD-25)

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp. (SD-110).

Supply and fixing of single box type 4'36W fluorescent fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. (SD-87)

Supply and run of 2 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD-59).

L.THEERTHALINGAM