RMS/Laying of Pipe and Pumps/01/2022

Amount

Excavation trenchs of required width for pipes , cables including for sockets and dressing of sides, ramming of bottoms, depth upto 1.50 meter, including getting out the excavated soil, and then retuming the soil as required in layers not exceeding 20 cm in depth. including consolideting each deposited layer by ramming watering etc.and disposing of surplus excavated soil as directed. with in a lead of 50 meter.( all kind Soil)

Providing and laying , jointing in position HDPE Pipe 32 mm of grade PE -80 ,PN-16 confirming to IS: 4984-2016 ( with IS mark )and for the respective working pressure with all fittings and accessories e.g coupling , tees, bends, reducers, screwed adater, flanged tail pieces etc. fllowing dia meter and pressure class complete in all respect. air release valve with accessories @ 100 meter each ( earth work in tranching to be measured and paid for sepratly) etc , Complete.

Excavation in fondation trench etc. in earth work lift upto 50mm stacking the excavated soil not more 3 metres clear from the edge of excavation then returing the stacked soil in 15 mm layers when requiiled in plinth side of foundation etc. consolidation each deposiled layer by remming & watering then disposing all surpluss excavated earth as disrected with in a lead of 20 metres

Providing and laying cement concrete work 1:5:10 ( 1 cement:5 sand:10 graded stone aggregate 40mm nominal size) and curing complate excluding cost of work in foundation & plinth.

40 mm Cement Concrete flooring 1:2:4 ( 1Cement: 2Coarse Sand :4 graded Stone aggregate) finished with a flooting coat of neat cement.

Providing and laying cement concrete work 1:2:4 (1cement:2 sand:4 graded stone aggregate 20mm nominal size) and curing complate excluding cost of work and reinforcement for reinforced concrete work in suspended floor landing and shelves and their support balconies beam girderd, bressmeers and cantilever up to floor two level.

Steel work welded in built up section / framed work in cluding cutting, hoisting. Fixing in position and applying a priming coat of approved steel primer using structural steel etc as required . Control panel Hut ( Main Supply)

Providing corrugated G.S Sheet roofing including vertical/ cuned surface fixed with polymer coated j or l hooks bolts and nuts 8 mm diameter with bitumen and G.I limpet washers filled with white lead including a coat of approved steel primer and two coats of approved paint on over lapping of shats complete ( upto any pitch in horizotal/ vertical or curved surfaces ) excluding the coat of purlins rafters and trusses and wherever required.Control Panel Hut ( Main Supply) Roofing

Providing ridges hips of width 60 cm overall width plain G.S sheet fixed with polymer coated j or l hooks bolts and nuts 8 mm dia G.I limpet and bitumen washers complete. Control Panel Hut ( Main Supply) Roofing

Providing fixing 1 mm thick M.S sheet door with frame of 40x40x6mm angle iron and 3 mm M.S gusset plates at the junction and corner, all necessary fittings complete . Including applying a priming coat of approved steel primer.Control Panel Hut ( Main Supply) Shutter

Random rubble Masonry with Stone in foundation and plinth including levlling up with cement concrete 1:6:12 (1 Cement :6 Coarse Sand :12 Graded Stone aggregate 20 mm nominal Size) upto plinth level. Intake pit for water lifting pointr required.Control Panel Hut ( Main Supply) Roofing

Providing and fixing Pump Submersible ( Motor 3 H.P Pump type CORA4C/23 single Phase) all fittings and accessories including control panel etc ,Complete.

VIRENDER SHARMA

Manoj Kumar

Lalit Kumar

Ashok Kumar

PANKAJ KUMAR

RAJESH KUMAR

Virender Pundir