PROVN OF KLP FOR COMMAND MILITARY DENTAL CENTRE (SWC) AT JAIPUR

Amount

Lump sum price worked out by the contractor for "BUILDING WORKS" as listed in Schedule ‘A’ Part-I representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 28 (R)

Lump sum price worked out by the contractor for "INTERNAL WATER SUPPLY " as listed in Schedule ‘A’ Part-II representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 30 (R)

Lump sum price worked out by the contractor for "INTERNAL ELECTRIFICATION" as listed in Schedule ‘A’ Part-III representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 35 (R)

Lump sum price worked out by the contractor for "EXTERNAL WATER SUPPLY" as listed in Schedule ‘A’ Part-IV representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 37 (R)

Lump sum price worked out by the contractor for "EXTERNAL ELECTRIFICATION " as listed in Schedule ‘A’ Part-V representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 41 (R)

Lump sum price worked out by the contractor for "ROAD, PATH AND CULVERT etc." as listed in Schedule ‘A’ Part-VI representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 44

Lump sum price worked out by the contractor for "SEWAGE DISPOSAL" as listed in Schedule ‘A’ Part-VII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 46 (R)

Lump sum price worked out by the contractor for "AREA DRAINAGE" as listed in Schedule ‘A’ Part-VIII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price of prepriced by the MES B/F from Sl page No. 47 (R)

Lump sum price worked out by the contractor for "SECURIRY FENCING, COMPOUND WALL AND GATE" as listed in Schedule ‘A’ Part-IX representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No.49 (R)

Lump sum price worked out by the contractor for " EXCAVATION & EARTH WORK AND SITE CLEARANCE " as listed in Schedule ‘A’ Part-X representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 51 (R)

Lump sum price worked out by the contractor for "(RAIN WATER HARVESTING )" as listed in Schedule ‘A’ Part-XI representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No.52

Lump sum price worked out by the contractor for "LIGHTNING PROTECTION " as listed in Schedule ‘A’ Part-XII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 53

Lump sum price worked out by the contractor for " FIRE DETECTION , FIRE ALARM AND FIRE FIGHTING " as listed in Schedule ‘A’ Part-XIII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No.57 (R)

Lump sum price worked out by the contractor for "COOLING APPLIANCES" as listed in Schedule ‘A’ Part-XIV representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No. 58

Lump sum price worked out by the contractor for " DEMOLITION AND DISMANTLING " as listed in Schedule ‘A’ Part-XV representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES B/F from Sl page No.59(R) (R)

Sch 'A' Sec-XVII (MISCELLANEOUS ITEMS) Notes: (i) This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only. (ii) Excavation and earth work except for the items which categorically includes for same shall be measured and paid separately under SCH A PART-X (Excavation and earthwork schedule).

INTERNAL WATER SUPPLY

S & F CPVC gate valve half turn 25 mm conforming to ASTM-D 2846 for unions and fixed complete including jointing and fittings as required.

S & F CPVC gate valve half turn 40 mm conforming to ASTM-D 2846 for unions and fixed complete including jointing and fittings as required.

S & F brass chromium plated WHB Mixer for mixing hot and cold water screwed down for iorn pipe 15 mm bore and fixed including fitting as required.

S & F brass chromium health faucet 1.20 m pipe make Jaquar cat part no. 573 or technocommercial equvivalent make as approved by GE.

S & F 15 mm bore two in one Bib tap cast copper alloy chromium plated fancy type with crutch or butterfly handle scrwed down screwed for iron pipe or union of make Jaquar cat part no. 35041PM or technocommercial equvivalent make as approved by GE.

INTERNAL ELECTRIFICATION:

S&F 20W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed, of make CG cat part No. CCS-100-20-65-HL2-BP-NWH, make BAJAJ cat part No. BCLSB18NW OR technoccommercial equvivalent out of makes specified as approved by GE.

S&F 36W ceiling mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed, make CG cat part No. LCTLRF7-36-DCL, make BAJAJ cat part No. BPRF36W WH SL LED OR technoccommercial equvivalent out of makes specified as approved by GE.

S&F 10W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed, make CG cat part No. LDL-10-NW, make BAJAJ cat part No. BCLSB-10-NW OR technoccommercial equvivalent out of makes specified as approved by GE.

S&F BEE five star rated energy efficient high-speed ceiling fan having 1200 mm blade sweep, air-flow not less than 210 CMM, operating voltage 220-240 V and frequency 50 Hz, including a down rod of suitable size and electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fan of make havells cat part. ES NEO, make CG cat part. HS Plus, OR technoccommercial equvivalent out of makes specified as approved by GE, complete all as specified and directed

S&F engery efficient metalic exhaust fan having blade sweep 300mm, air delivery not less than 900 cum/h, operating voltage 220-240V and frequency 50 Hz, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the exhaust fan make Havells cat part no. Ventil Air DSP, make CG cat part No. DE-022, Make Bajaj cat part. BAHAR OR technoccommercial equvivalent out of makes specified as approved by GE, complete all as specified and directed

S&F 25W LED bldg security light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 100 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP-66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting with bracket arm OD 35 mm to 42mm including necessary electrical connection to the fixture with 3 core flexible Cu conductor cable of appropriate size and 1.5 m long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed, make CG cat part No. LSTS-25-CDL-M, make HPL cat part No. HPL-LED-SL-2560S, make BAJAJ cat part No. BCLST-25W-LED OR technoccommercial equvivalent out of makes specified as approved by GE.

S&F ISI marked MCB for AC supply till 63 A, having breaking capacity Icn = 10 kA, conforming to IS/IEC 60898-1-2002, sliding bottom clamp, colour coded on/off indication on dolly, biconnect IP 20 protected lower terminals and sliding shutters, all complete as specified and directed of following capacity: -.

(a) 6 - 32A, SP MCB, C- curve

(b) 40A, SP MCB, C- curve

(c ) 63A, SP MCB, C- curve

(d) 16A, SPN MCB, C- curve

(e) 25A, SPN MCB, C- curve

(f) 32A, SPN MCB, C- curve

(g) 40A, SPN MCB, C- curve

(h) 63A, SPN MCB, C- curve

(j) 40A, TP MCB, C- curve

(k) 63A, TP MCB, C- curve

S&F MCCB, 100A, 18 KA, 4 Pole, thermal magnetic release, Ics = 100%, Icu complete all as specified and directed.

S&F MCCB, 63 A, 18 KA,4Pole, thermal magnetic release, Ics = 100%, Icu complete all as specified and directed.

S&F MCCB, 40 A, 18 KA, 4 Pole, thermal magnetic release, Ics = 100%, Icu complete all as specified and directed.

S&F MCCB, 25 A, 18 KA, 4 Pole, thermal magnetic release, Ics = 100%, Icu complete all as specified and directed.

M & L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of strata, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed as following.(Contd...)

NOTES : (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC M25 design mix using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) Item includes the cost of 7.5 M GI pipe for protection of earth wire. Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.5 M earth lead wire. Any variation in length shall be adjusted through deviation order. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

S&F modular RJ - 11 for telephone socket tool complete with mild steel sunken boxes with earth dolly zink coated and including mounting frame & over cover plate all as specified and directed.

S&F modular TV socket complete with non metallic modular sunken boxes with earth dolly zink coated and including mounting frame and over cover plate all as specified and directed.

S&F telephone switch board cable of size 0.5mm ATC PCV insulated all complete all as specified and directed.

S&F TV socket cable solid annealed copper conductor, JF, aluminium foiled and aluminium wire braided, RJ - 11 (foam) complete all as specified and directed.

EXTERNAL WATER SUPPLY

M & L for brick masonry valve pit (type) of size 900 x 600 x 1000 mm (internal dimension) complete with plastering internally on walls , MS angle iron 40 x 40 x 6mm frame work & 3 mm MS sheet top cover openable through hinges including necessary locking arrangement, all as per TD drawing including necessary excavation and earth work in any type of strata and two coats of anti-corrosive paint over a coat of zinc primer on steel surface complete all as specified and directed.

M & L for brick masonry valve pit (type) of size 450 mm x 450 mm x 600 mm (internal dimension) complete with plastering internally on walls , MS angle iron 40 x 40 x 6mm frame work & 3 mm MS sheet top cover openable through hinges including necessary locking arrangement, all as per TD drawing including necessary excavation and earth work in any type of strata and two coats of anti-corrosive paint over a coat of zinc primer on steel surface complete all as specified and directed.

Supply, laying in trenches, under floor, under road, connecting , jointing and testing 100mm bore, centrifugally cast ductile iron (DI) spun pressure pipe, class K-7, ISI marked, with socket and spigot ends confirming to IS- 8329/2000 standard length, with outside zinc coating and bitumen finished layer (minimum thickness 70 microns) including EPDM joining ring/gasket IS-5382 of suitable size complete all as specified and directed. Note :- (i) Excavation and earth work shall be measured and paid under respective item of this schedule. (ii) Fitting shall be measured and paid for separately under respective items of this schedule. (iii) Joint shall not be measured and paid for separately.

Ductile iron fittings IS 9523 marked viz bends, tapers, reducers, tee pieces (single or double branch) any type angle/ radius and straight connecting pieces flanged/ socket and spigot ends, size of following pipe upto 150 mm bore complete all as specified.

EXTERNAL ELECTRIC SUPPLY

S&F street/road light, pressure die cast alluminium housing,heat resistant toughened glass with frame, IP-66 protection, complete with BIS registered potted electronics driver, operating voltage range 140 to 270 volts better optics for uniform distribution of 40 watts and including twisted flexible copper conductor cable with suitable size for connection from Junction box to street light fighting with and including necessary arrangement for fixing of light with bracket made out of 50 mm bore GI pipe medium grade of length 1.50 m. bent to shape, with MS clamps. nuts, bolts etc. complete all as specified and directed, make CG cat part No. LSTS-40-CDL-M, make HPL cat part No. HPL-LED-SL-4060S, make BAJAJ cat part No. BRTFG-45W-LED OR technoccommercial equvivalent out of makes specified as approved by GE.

S&F street/road light, pressure die cast alluminium housing,heat resistant toughened glass with frame, IP-66 protection, complete with BIS registered potted electronics driver, operating voltage range 140 to 270 volts better optics for uniform distribution of 72 watts and including twisted flexible copper conductor cable with suitable size for connection from Junction box to street light fighting with and including necessary arrangement for fixing of light with bracket made out of 50 mm bore GI pipe medium grade of length 1.50 m. bent to shape, with MS clamps. nuts, bolts etc. complete all as specified and directed,make CG cat part No. LSTP-72-CDL-M, make HPL cat part No. HPL-LED-SL-7260S, make BAJAJ cat part No. BRTFG-725W-LED OR technoccommercial equvivalent out of makes specified as approved by GE.

S&F poly carbonate junction box, weather and vermin proof of size 250X250X160mm including provn of 4 Nos aluminium strip 25x3.15mm size bus bar single phase and neutral suitabely mounted on bus bar insulators, including one No. MCB, SP 6 Amps for light control, drilling of holes.Provn of suitable size of GI nuts, bolts, double washer and flat iron clamps of suitable size for taking connections and fixing on LT steel tubular poles with locking arrangement complete all as specified and directed.

supply, install, testing & commissioing of LT panel outdoor type, dust and vermin proof totally enclosed, with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP-65 standard double shutter gears front and rear frame work and 3.15mm thick MS sheet duly powder coated made of 40 x 40 x 6mm thick angle iron frame including necessary PCC work all as specfified suitable for 415 Volts, 50 Hz 3 phase and neutral system and shall be completed with 800 Amps capacity aluminium bus bars with bus bar chamber, internal wiring with suitable size of PVC insulated copper cable, copper lugs comprising of following accessories (Main panel) :- Incoming : (a) MCCB 4 pole 630 Amps, 50 KA breaking capacity, with thermal and magnetic release-01 Nos (b) LED multifunctional meter accuracy class 1.0 along with Following parameters : VA, F, PF, KW, KVA, KVAR, KWh, KVAh, KVARh, run hours, On hours ,Intrrupts, RPM, % - 01 No. Outgoing : (a) MCCB 4 pole 200 Amps with thermal & magnetic adjustable setting 36 KA - 01 Nos. (b) MCCB 4 pole 250 Amps with thermal & magnetic adjustable setting 50 KA - 02 Nos. (c) MCCB 4 pole 100 Amps with thermal & magnetic adjustable setting 25 KA -02 Nos. (d) LED Indicating lamp - 03 Nos.

supply, install, testing and commissioing of LT panel outdoor type, dust and vermin proof totally enclosed, with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP-65 standard double shutter gears front and rear frame work and 3.15mm thick MS sheet duly powder coated made of 40x40x6mm thick angle iron frame including necessary PCC work all as specfified suitable for 415 Volts, 50 Hz, 3 phase and neutral system and shall be completed with 400 Amps capacity aluminium bus bar with bus bar chamber,internal wiring with suitable size of PVC insulated copper cable copper lugs comprising of following accessories. Incoming : (a) MCCB 4 pole 250 Amps with thermal & magnetic adjustable setting 36 KA - 01 Nos (b) LED multifunctional meter accuracy class 1.0 along with Following parameters : VA, F, PF, KW, KVA, KVAR, KWh, KVAh, KVARh, run hours, On hours ,Intrrupts, RPM, % - 01 No. Outgoing : (a) MCCB 4 pole 100 Amps with thermal & magnetic adjustable setting 25 KA - 03 Nos. (b) MCCB 4 Pole 32 Amps with thermal & magnetic adjustable setting 25 KA -01 Nos. (c) LED Indicating lamp - 03 Nos.

supply, install, testing & commissioing of LT panel outdoor type, dust and vermin proof totally enclosed, with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP-65 standard double shutter gears front and rear frame work and 3.15mm thick MS sheet duly powder coated made of 40x40x6mm thick angle iron frame including necessary PCC work all as specfified suitable for 415 Volts, 50 Hz, 3 phase and neutral system and shall be completed with 400 Amps capacity aluminium bus bar with bus bar chamber, internal wiring with suitable size of PVC insulated copper cable, copper lugs comprising of following accessories. Incoming : (a) MCCB 4 pole 250 Amps with thermal & magnetic adjustable setting 36 KA - 01 Nos. (b) LED multifunctional meter accuracy class 1.0 along with Following parameters : VA, F, PF, KW, KVA, KVAR, KWh, KVAh, KVARh, run hours, On hours ,Intrrupts, RPM, % - 01 No. Outgoing : (a) MCCB 4 pole 100 Amps with thermal & magnetic adjustable setting 25 KA - 03 Nos. (b) MCCB 4 Pole 32 Amps with thermal & magnetic adjustable setting 25 KA - 02 Nos. (c) MCCB 4 Pole 16 Amps with thermal & magnetic adjustable setting 25 KA - 01 Nos. (d) LED Indicating lamp - 03 Nos.

Supply, install, testing & commissioning of LT panel outdoor type, dust and vermin proof totally enclosed, with sloping canopy fabricated out of steel sections, the door opening shall not be less than 150 degree. The construction of panel board shall be dust, vermin proof, IP-54 standard double shutter gears front and rear frame work and 3.15mm thick MS sheet duly powder coated made of 40x40x6mm thick angle iron frame all as specfified suitable for 415 Volts, 50 Hz, 3 phase and nuetral system and shall be completed with 200 amps capacity Aluminium bus bar with bus bar chamber, internal wiring with suitable size of PVC insulated copper cable, copper lugs comprising of following accessories (For JCO and ORs pocket - 03). Incoming : (a) MCCB 4 pole 100 Amps with thermal & magnetic adjustable setting 25 KA - 01 Nos. (b) LED multifunctional meter accuracy class 1.0 along with Following parameters : VA, F, PF, KW, KVA, KVAR, KWh, KVAh, KVARh, run hours, On hours ,Intrrupts, RPM, % - 01 No. Outgoing : (a) MCCB 4 pole 100 Amps with thermal & magnetic adjustable setting 25 KA - 03 Nos. (b) MCCB 4 Pole 16 Amps with thermal & magnetic adjustable setting 25 KA - 02 Nos. (c) MCCB 4 pole 25 Amps 25 KA with thermal & magnetic adjustable setting - 01 Nos. (d) MCCB 4 Pole 32 Amps with thermal & magnetic adjustable setting 25 KA - 02 Nos. (e) Auto timer switch - 01 Nos. (g) LED Multifunctional meter - 03 Nos.

M&L for trench less technology boring by HDD machine below existing road/ path for laying of any sizes cable including making good the disrurbed portion/ surface complete all as specified and directed appx dia of bore is 150 mm and depth of bore is 60 cm below GL.

M & L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 32 x 6 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 40 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of strata, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed. Refer Notes below: - (Contd.....)

NOTES :- (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC M25 design mix using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) Item includes the cost of 7.5 M GI pipe for protection of earth wire. Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.5 M earth lead wire. Any variation in length shall be adjusted through deviation order. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

S&F Servo type Voltage Stabilizer of capacity 400 KVA for automatic voltage correction 3 O 50 Hz Oil cooled input voltage260-480 Volts, Output voltage 415 Volt +/- 1 %, efficiency more than 95 % , correction speed 8 volts per second, diggital display, indoor floor mounted, portable, response time 10 ms with surge protection, control through micro controlled digital circuit, with display, input, out put, low/high voltage, time delay, main ON , low/high voltage cut off, wave form distortion-Nil, with buck, boost, double copper wound transformer with high quality CRGO lamination & 99.9 % pure copper with suitable toroidal wound, vairec geared servo motor unit with limit switches to avoid over runningat highest and lowest position, microprocessor controller, digital controller/IC based solid state plug in type glass epoxy control card, immune to load PF and supply frequency variation, max power losses 2 % , with auto/ manual operation with bypass arrangement and with first fill high quality EHV oil as per IS- 335, Voltage stabilizer shall be as per IS-9815 & IS-2026 complete all as specified of Make Volina, Andreyule/AE/V-Guard complete all as specified.

ROAD FURNITURE

S&F Solar Studs LED based made of aluminium alloy shell of size 125mm x 125mm x 25mm (shank 60mm) 100% water proof according to LP - 65, high efficiency mono-crysiline solar panel 2.4 V/0.3 wff, one Ni- Mh or Ni- cd rechargeable hattery (1.2V/1600MA) six super bright LEDs with 10000 to 18000 med (Milicandela), maintenance free, view distance upto 1000m, flash rate 2 Hz, bearable weight 10 Ton (approx) complete all as specified and directed. Model No : DA 110 (DHRUV) of DARK EYE or equivalent make

S&F Delinators comprising two high perfrmance 100mm dia reflectors and two rectangular reflectors of EYE or equivatent 70mm x 23mm fixed on both sides of gulde post, refiectors shall be positioned at the best eye guiding level so that drivers can be warned from a safe distance. The body of Gulce post shall be moulded in ABS plastice and fixed on powder coated steel pipe of 1.0m height complete all as specified and directed. Model No : DA 74 of DARK

S&F informatory sign board (Single side) of size 900mm X 600mm made out 2mm thick aluminum sheet duly framed with MS angle iron 40X40X5mm size with the help of stainless steel nuts/bolts aluminum rivets with front face of aluminim sheet to be fully covered by blue diamond grade micro prismatic type IX retro reflectve sheeting material by over lay with colour film and back side painted grey epoxy paint including fixing of two posts of mild steel heavy grade, 75mm dia pipe duly painted in black & white alternate bands of fluorescent synthetic enamel paint over a coat of zinc chrome primer with plate welded at bottom including necessary earth work embedded in concrete ete complete as per drawing No TD/2013/02 Sheet 1/1

FENCING AND GATE:- S&F 450 x 450 x 900mm size Karoli stone chattries complete all as directed and specified.

RAIN WATER HARVESTING

M&L for boring holes in any type soil for encasing PVC/HDPL 150 mm pipe for 6.0m deep complete all as specified and directed.

S&F 150mm bore, perforated PVC/HDPE pipe for inserting in hole complete all as specified and directed.

M&L for pea gravel of size 3 - 6mm to be filled in perforated pipe complete all as specified and directed.

S&F 150 mm dia stainless steel grating complete all as specified and directed.

LIGHTNING PROTECTION

M & L for Earthing complete with Copper earth plate electrode 60 cm x 60 cm x 3.15 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to copper earth strip 20 x 3 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 40 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of strata, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed.

NOTES :- (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC M25 design mix using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) Item includes the cost of 7.5 M GI pipe for protection of earth wire. Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.5 M earth lead wire. Any variation in length shall be adjusted through deviation order. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

FIRE DETECTION AND ALARM SYSTEM

S&F detectors complying with and type certified to EN-54 addressable type multisensor detectors with heat and smoke combination Photoelectric/ Optical with base with self built intelligence as per IS-11360 all as sepecified and directed.

S&F dual LED type response indicator all as sepecified and directed.

Supply of Analog Addressable Type Manual Call Point having surface or flush mounting option fully complaint to EN-54 having Rotary Decade Swicthes for Addressing from 01-99 complete with Back Box for mounting complete as specified conforming to BS5839 standards and duly approved by EN-54/ LPCB of Make : Honeywell Morley, Siemens, Gent.

Supply of Fault Isolator base with termination preferably after every 10-15 devices and shall be able to isolate electrical short circuit in the wiring etc. all as specified of Make : Honeywell Morley , Siemens, Gent.

S&F two Loop Micro Processor based 1 wire fault tolerant loop, required loop networkable type (each loop accessing 99 detectors and 99 modules ) fire alarm/detection control panel. The panel shall be able to give location of all fire/fault conditions of addressable units via the address codes. Further, the panel must be able to automatically switch ON /OFF respective control module when ever any alarm is triggered. The panel shall have rectifier, Loop cards, 80 character LCD unit to indicate Fire/Fault Signal with addresses. The Panel Shall be Sheet Steel Painted, sealed to IP30. The panel have provision to integrate with PA System . The panel shall have a built in power supply and battery charger along with maintenance free 24 AH, 2 x 12 volt SMF dry batteries capable of running for a minimum of 48 hours with battery charger complete as required. and conforming to BS5839 Standards and Duly Approved by EN54/LPCB. GSM Auto dialer intigration required complete all as specified and directed. Make : Honeywell Morley, Gent, Siemens.

S&F Active Repeator Panel complete all as specified and directed. Make: Honeywell Morley, Siemens, Gent.

Supply, install, testing and commissioning Addresscable Central Modular Hooter complete as specified and directed.

S&F Audio cum Visual Alarm system consisting of a hooter and TV monitor panel to indicate the location of fire including necessary wiring complete all as specified and directed.

S&F Electric Siren System, AC, 415 V, 50 HZ, including necessary foundation and protection from rain water of range 2 Kms installed at roof of building complete all as specified and directed.

M&L for 2 core, 1.5 sq mm flame retardent low smoke, PVC insulated aurmored bright annealed copper conductor cable, 1100 volts grade drawn through in the surface / concealed conduit as required Wiring with 2 Core x1.5 Sqmm FRLS PVC sheathed copper conductor cable complete all as specified and directed.

S&F 20mm dia, 16 SWG mild steel conduit, stove enamelled black both internally and externally alongwith accessories in concealed/ surface for above cable complete all as specified and directed.

All as per item 77 above, but MS conduit of size 25mm dia with necessary accessories etc.

All as per item 77 above, but MS conduit of size 40mm dia with necessary accessories etc.

Supply of Addressable Type Loop Powered Sounder complete with Mounting Base as required conforming to BS5839 Standards and duly Approved by EN54/LPCB complete all as specified. Make : Honeywell Morley , Siemens, Gent

Supply of Output Control Module for Lift,AHU, pressure fan/Exaust fan etc. all as specified. Make : Honeywell Morley, Siemens, Gent

Supply of Input Monitor Module for FA panel intigration with fire fighting flow switch all as specified. Honeywell Morley, Gent, Siemens

FIRE FIGHTING SYSTEM

Supply, installation, testing & commissioning of Booster pumps for 440 V, 3 Phase, 50 Hz Confirming to IS - 12469 : 1988 With CI Casing bronze impeller and stainless steel shaft mounted on heavy duty bearings suitable for 440 volts, 3 phase AC Supply , 50 Hz capable of delivering 450 LPM discharge at 70 metre head with and inlcuidng suitable capacity coupled to suitable squirrel cage TEFC induction motot 1500 RPM (syn) and mounted on common base plate including suction and delivery connections , DOL started 3 Phase 415 Volts, 50 Hz. (1 Working + 01 Stand by) complete all as specified and directed.

Supply, fixing, jointing, testing and commissioning black mild steel pipe (IS:1239 Part - I), heavy grade, 'C' Class with fittings like, unions, couplings, bends, elbows, tees, offsets, reducers, flanges. Painted MS structural supports, hangers, fasteners etc. as directed complete the work as per the requirement at site including painting with two coats of synthetic enamel paint, over a coat of primer after surface preparation, cutting and making good the walls complete. Pipe upto 50 mm dia will be with threaded joints with malleable iron fitting conforming to IS: 1879 and 65 mm dia and above will be with butt welded joint. (for internal exposed pipes in shafts and ceiling) complete all as specified and directed for the following sizes:-

(a) 25 mm dia

(b) 80 mm dia

(c ) 100 mm dia

S&F 80 mm dia inlet ISI marked SS fire hydrant valve with single outlet and fitted with 63 mm dia instantaneous female coupling on the outlet complete including companion flange as, PVC blank cap and chain, nuts, bolts and 3 mm thick compressed asbestos gasket at locations as per drawings (Conforming to I.S.5290-1993 Type-A) complete all as specified and directed.

Providing and fixing 63 mm dia 30 m long EPDM lined fabric hose including SS male and female instantaneous type coupling approved by fire authority, machine wound with copper wire complete in all respects. Hose shall conform to I.S. 636 Type A and coupling to I.S. 903-1975 with ISI certification complete all as specified and directed.

Providing, fixing testing and commissioning standard short size S.S branch pipe with SS nozzle 16 mm dia outlet (Conforming to I.S. 903) with standard instantaneous type 63 mm dia coupling complete all as specified and directed.

Providing, fixing, testing and commissioning of gunmetal single acting air valve with screwed inlet 25 mm dia as per IS 12992 with 25mm dia isolation ball valve rated for 20 Kg/Sp.cm complete in all respects complete all as specified and directed.

Providing and fixing CO2 extinguisher consisting of seamless MS cylindrical body squeeze lever discharge valve, internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle ISI marked as per IS 15683 including fixing with dash fasteners etc. of Capacity 4.5 Kg complete all as specified and directed.

ABC type fire extinguisher initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure CO2 gas cartridge, discharge hose, wall mounting bracket etc., complete, confirming to IS:2171 of Capacity 6 Kg complete all as specified and directed.

Fire buckets round bottom type enamel painted, white inside and Red out side and Letter "FIRE" in black out side and handle with mounting bracket complete all as specified and directed.

Fire bucket stand fabricated by MS angles to install 2 Nos. of buckets complete all as specified and directed.

Supply, fixing, testing & commissioning of 80 mm dia inlet CI flanged "Y" type Strainer with SS mesh, suitable flanges, nuts, bolts, gaskets etc. complete all as specified and directed.

Supply, fixing, testing and commissioning of MS cabinet fabricated from 16 gauge MS sheet with full front glass door and locking arrangement for pad lock with suitable shelves for keeping 24 spare sprinklers and one spanner properly fixed in the shelves and cabinet painted fire red with stove enameled of approved shade size 750 x 600 x 150 mm. including the cost of spanner set and 5 rolls of taflon tape complete all as specified and directed.

Supply, fixing, testing and commissioning of electrical motor driven Fire Pump suitable for automatic/ manual operation complete all as specified and directed for the following specifications. Horizontal Split casing type, centrifugal, multistage, pump of cast iron, body and bronze impeller, stainless steel shaft coupled directly through flexible coupling on a common fabricated MS base frame to suitable capacity TEFC Squirrel cage induction motor suitable for operation on 400/440 Volts (+/-5%) 3 phase, 50HZ, A.C. supply. The pump set shall be complete with couplings, coupling guard, vibration insolation pads (cushy food). the pump set hall be suitable for 2850 lpm of flow and total head of 70 metre and shall also be capable to deliver 150% of rated head when running at 2900RPM speed as approved by GE.

Supply, Installation, Testing and Commissioning of Diesel Engine Driven Main Fire Pump suitable for auto operation and consisting of following: complete in all respect as required. b)Horizontal Split casing type, centrifugal, multistage pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm. at highest and farthest outlet at specified flow of 2850lpm at 70 Mtr. head confirming to IS 1520. c)Suitable HP (minimum 70 BHP) 1500- 2100 RPM, 4 stroke, cold starting type Diesel Engine with Heat Exchanger confirming to relevant BIS & IS Standards, complete with all required accessories / system, fuel oil filter, lubricant oil pump . d) Common bed plate for mounting pump and Engine fabricated of suitable M.S Channel as per manufactures recommendations.e) Suitable RCC pump foundations as per manufactures design 8 nos. Dunlop Anti vibration (cushy foot) heavy duty mounting pads. f) 1 No. 200 Lits capacity day oil storage tank fabricated from 4 mm thick M.S. plates. Tank shall be provided with inlet, outlet, overflow, vent drain connections, manhole cover (300 mm I.D.) & level indicator. Tank shall be mounted on 2 m high steel structural supports with access ladder (Painted with 2 coats of red oxide paint). Tank shall be provided with epoxy coat from inside out-side with one coat of red oxide & two or more coats of synthetic enamel paint of approved colour. g) 24 volts 180 AH lead acid battery (12 volts - 2 Nos) .......Contd....

with boost/Trickle charger for starting the engine automatically complete as required. h) 20m M.S. class 'B' pipe for diesel pump exhaust pipe including all fittings like bends, tee, clamps/structural steel support of suitable dia for the engine. The pipe shall be insulated with 50 mm thick fibre glass wool and 24 guage aluminium cladding as instructed along with bird proof mesh at outlet and including anticorrosive treatment to buried pipes by wrapping with 4 mm thick bitumastic membrane applied over a coat of primer, cutting holes and chases in brick or RCC walls and making good complete. 150mm dia

Supply, fixing, testing and commissiong of double flanged vertical air vessel fabricated from 6mm MS plate for shell & with 8 mm dished ends, outside with one coat of primer and two coats of synthetic enamel paint of approved shade, complete with approved quality of pressure switches,safety valve 25mm dia ,50mm dia drain valve pressure gauge and all other required accessories to operate commonly main fire pump, sprinkler pump and Jockey pump at drop of pressure, automatically at required pressure setting including cost of wiring through MS conduit complete all as specified and directed. (i) Recommended dia : 450mm. (ii) Height of shell : 2000mm (ii) Working pressure : 10.0 kg/cm2

Supply, fixing, testing & commissioning of 100 mm dia CI flanged "Y" type Strainer with SS mesh, suitable flanges, nuts, bolts, gaskets etc. complete inlet all as specified and directed.

All as per item No : 101 above but of size 200 mm dia.

S&F 150 mm dia gunmetal controle valve with turbine type automatic alarm, drain valve, test valve and piping suitable for a working pressure of 15 kg/sqcm as per manufacturer's specifications and all as specified and directed.

S&F 25mm dia, 1000mm long NFPA/FM approved SS braided flexible sprinkler drops with locking arrangement complete all as specified and directed.

COOLING APPLIANCES

Supply, Install, testing and commissioning of refrigerators, electric driven, 230 volts (single phase), 50 Hz, having nominal store capacity 190 litres single door, minimum four star rating, toughness glass, shelves, light colour as approved by GE complete all as specified and directed.

LIFT/ELEVATOR :Supply, install, testing and commissioning of machine room less passenger elevator of model PWI08/10-19 of KONE Elevator or techno commercial equivalent model in OTIS/Jonson/ Schindler as approved by GE, with AC variable voltage, variable frequency control, Automatic centre opening, sliding steel doors, OEM manufactured all as specified below of :- (a) Type of lift : Passenger lift for 08 passengers (for G+ 01 Upper floor) (b) Load : 544 Kg (c) Speed : minimum 1 m/Sec (d) Power : 400 V (-) 15% + 10% , 3 phase 50 Hz (e) Type of control : AC variable voltage variable frequency (with close Loop) (f) Stops and opening : 2 stops & 2 opening (all opening in same side side) (g) Machine : Geared traction machine placed in the hoist way overhead (h) ---Blank--- (j) Car Size : 1100 mm wide x 1300 mm deep x 2200 mm high inside dimesion (k) Cars doors : Centre opening sliding Car enclosure : All stainless steel panels in vandal finish. (l) Car panels : All stainless steel panels in vandal finish (m) False ceiling : Full ceiling of powder coated frame & panel with elegantly plan LED down lights (n) Car entrance : Protected by centre opening sliding stainless steel doors in vandal finish of size 800 mm wide x 2000 mm high (o) Door operation : Automatic with ACVVVF door with electronic door protection device (p) Hand railing on three sides : Mirror stainless steel finish (q) Car and counter : Guide Rails of T-Section (r) Weight Guide : Mild Steel (s) Flooring : 3 mm PVC - pattern Dark Grey Marble Pattern (t) Signal design type S-60 or equivalent with the following features : (i) Combined luminous hall button with seven segment digital hall position indicator at all floors. (Contd.......)

(ii) Car operating panel with luminous floors buttons in car combined with direction arrows (iii) Overload warning indicator (iv) Battery operated alarm bell and emergency light (v) Fireman's switch (vi) Automatic rescue device with maintenance free batteries (vii) Voice synthesizer (viii) Intercom (ix) Sixteen segment LCD type panel car position indicator in car (x) Integrated Roof RL75 Stainless Steel Pyramid Lighting LED and cabin fan inside the car. (xi) Face plate finish : Stainless steel in hair line finish. (xii) Face plate shape : Rectangular (xiii) Emergency operation of lift by manual device by automatic rescue device (ARD) (xiv) 3D infrared sensor (3 Nos) on each in car, and near Ground floor,landing door all as per IS 14665 (xv) Automatic Manual and dual control system. (aa) Location : CMDC complex (ab) Travel length : 4 mtr (Approx) (ac) Operation : Simplex, full collective (with/without attendant) (ad) ---Blank--- (ae) Lift well : 1900 x 1900 mm (upto full height) (af) Pit depth - 1500 mm (ag) OH - 5100 mm (Note :(i) Building works for reference only. These are excluding from scope of work herein and shall be constructed as part of civil works in the building. (ii) Dimensions of car size, Entrance, Head room, wall opening are for guide line and are tentative.The contractor shall have to provide car size according to size of lift well as per manufactureres recommomdations, for type and make of lift being provided by him and no extra whatsoever shall be admissible to him on this account.

DG SET: -Supply, installation, commissioning and testing complete of Manufacturer or OEM (Original Eqpt Manufacturer) manufactured and tested static Diesel Engine driven generating set capable of delivering 400 KVA continuous rating, (10% overload for 1 hour in 12 hours of operation), 415 volts (AC 3 Phase, 4 wire system of supply), 50 Hz at power factor 0.8 minimum. The DG set shall consist of a diesel engine coupled directly to a matching alternator, and mounted on Dunlop metallastik foundation pads on a common base frame and thereafter installed in the CPCB approved acoustic enclosure complete with control panel standardised by manufacturer, fuel tank with mounting arrangement and inlet, outlet, return oil arrangement, flexible exhaust pipe complete all as specified and directed , prime rating as per ISO 8728. 10% overload provision available for intermittent periods and shall comprise of the following : - (a) Engine (prime mover) : Diesel engine 1500 RPM, of suitable HP as recommended by manufacturer, water cooled, turbocharged, 12 volts electric battery start, complete with fly wheel and torsional vibration damper, radiator and all standard fittings/ fixtures as per standard manufacturing practices and including suitable instrument panel with RPM meter, lub oil temp and pressure gauge, water temp gauge and frequency meter (digital type), battery charging ammeter and fuses, and also including self starter ( 12V), battery charging alternator, fuel tank etc and complete with HWT and LLOP alarm and shut down safeties complete with first fill of Lub oil and Coolent and conforming to BS 5514/ ISO 3046 (Contd....)

of Cummins make or equivalent KIRLOSKAR (KOEL) / GREAVES. (b) Alternator : AC alternator, brushless, 415V AC 50 Hz, 3 phase , 4 wire type, rated for continuous output of 400 KVA, PF 0.8 (lag), 1500 RPM insulation class ‘H’; enclosure SPDP (IP 23), self excited & self regulated with AVR for + 1 % voltage regulation, coupled directly / suitably to and to match the above engine and conforming to BS 5000/IS 4722. Alternator makes shall be KIRLOSKAR/ STAMFORD/ GREAVES/BHARAT BIJLEE. (c) Dunlop Metallastik anti-vibration pads for mounting engine : alternator assembly on the base frame/ plate. (d) Base plate : Made out of structural steel as per manufacturer’s recommended design/ specifications. (e) Enclosure : Provision of an integral type, approved / certified acoustic enclosure as per latest CPCB norms, for the DG set to restrict the noise level to 75 DB (A) at one metre and ensure that temperature rise within the canopy shall not exceed 5 – 7 degree celsius. It shall be made of 16 SWG CRCA MS sheet with powder-coated finish on outside and high quality noise absorbent and fire retardant grade acuoustic insulation material duly provided with EPDN gasket lining. There shall be four hinged doors out of which one shall be with a glass window. The base frame shall be of ISMC . DG Set shall also include the following: -

(i) One - set of bus bar (The control cubicle will be furnished complete with the necessary control circuit fuses, etc. and will have provisions for making incoming and outgoing connections) Note : (i) In case AMF panel included instead of Standard Control Panel, then Battery charging alternator with inbuilt regulator and battery charging ammeter should be deleted from engine specifications since Battery charger included under AMF Panel Specifications. (ii) Plateform : PCC foundation /plinth/base shall be provided as per manufacturers instryutions. (iii) Tool kit, Operation and Maintenance catalogue, 1 year spare part list, overhauling manuals, guarantee card etc. shall be provided as per manufacturer standard practices.

AIR CURTAIN: - Supply, install, testing and commissioning of commercial Air Curtain unit of width of size 4 feet for prevention of dust and conditioned air losses, single phase, 220 V, 50 HZ, with sensor made out of MS/CRCA sheetof minimum thickness 18 gauge finished with two coats of red oxide primer and final coat of synthetic enamel paint (oven baked) with MS - CRC 18 gauge square perforated suction grills, Aluminium alloy fans and single phase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1 - 1.5 m/sec air velocity at floor level ,comp[lete all as specified and directed make, ALMONARD, AIRCON, FILTROX as approved by GE.

AIR CURTAIN: -Supply, install, testing and commissioning of commercial Air Curtain unit of width of size 3 feet for prevention of dust and conditioned air losses, single phase, 220 V, 50 HZ, with sensor made out of MS/CRCA sheetof minimum thickness 18 gauge finished with two coats of red oxide primer and final coat of synthetic enamel paint (oven baked) with MS - CRC 18 gauge square perforated suction grills, Aluminium alloy fans and single phase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1 - 1.5 m/sec air velocity at floor level ,comp[lete all as specified and directed make, ALMONARD, AIRCON, FILTROX as approved by GE.

HOT WATER SUPPLY

M&L for CPVC pipe of size 15mm bore for Hot Water Supply including all type necessary fittings, clamps etc on wall/ ceiling/floors complete all as specified and directed.

M&L for CPVC pipe of size 20mm bore for Hot Water Supply including all type necessary fittings, clamps etc on wall/ ceiling/floors complete all as specified and directed.

S&F CPVC Spears ball valve of size 15mm bore for Hot Water Supply complete all as specified and directed.

S&F CPVC Spears ball valve of size 20mm bore for Hot Water Supply complete all as specified and directed.

Supply, Installation, Testing and Commissioning of 'Solar Hot Water System' (FPC) based on indirect transfer of heat of capacity 100 LPD with heat exchanger type with, electric heating back up 3 KW and backup stainless steel hot water tank insultated complete all as specified and directed.

MEDICAL GAS SUPPLY : NOTE : The installation of Medical Gases Manifold system with accessories and Copper DHP Pipe line for Medical Gases supply shall be carried out in accordance with latest BS. The detailed layout diagram of Medical Gases Supply pipe line and manifold system to be submitted by the contractor.

Supply, install, testing and commissioning paitent calling system for reception and paitent waiting with visual and audio system (which include main display for waiting - 04 Nos and doctor calling system in room - 10 Nos) complete all as directed and specified.

Supply, install, testing, commissioning and errection of DHP medical grade pipe Solid drawn, seamless, de-oxidised, non-arsenical, half hard tempered and degreased, materials confirming to BS: 6017 latest revision (Cu-DHP) manufactured as per BS"2871/1971 part 1 Table X and dimension tolerance confirming to BS-EN 1057 pipe fitting: Make Janaya/Mexflow of 12 mm outer dia with wall thickness 0.70 mm., complete all as specified and directed.

Supply, install, testing, commissioning and errection of DHP medical grade pipe Solid drawn, seamless, de-oxidised, non-arsenical, half hard tempered and degreased, materials confirming to BS: 6017 latest revision (Cu-DHP) manufactured as per BS"2871/1971 part 1 Table X and dimension tolerance confirming to BS-EN 1057 pipe fitting: Make Janaya/Mexflow of 15 mm outer dia with wall thickness 0.90 mm, complete all as specified and directed.

Supply, install, testing, commissioning and errection of DHP medical grade pipe Solid drawn, seamless, de-oxidised, non-arsenical, half hard tempered and degreased, materials confirming to BS: 6017 latest revision (Cu-DHP) manufactured as per BS"2871/1971 part 1 Table X and dimension tolerance confirming to BS-EN 1057 pipe fitting: Make Janaya/Mexflow of 22 mm outer dia with wall thickness 0.90 mm complete all as specified and directed.

Supply, install, testing, commissioning and errection of DHP medical grade pipe Solid drawn, seamless, de-oxidised, non-arsenical, half hard tempered and degreased, materials confirming to BS: 6017 latest revision (Cu-DHP) manufactured as per BS"2871/1971 part 1 Table X and dimension tolerance confirming to BS-EN 1057 pipe fitting : Make Janaya/Mexflow of 28 mm outer dia with wall thickness 0.90 mm, complete all as specified and directed.

Supply, install and testing of Gas Outlet Point with prove Amico type for Oxygen, copper stubs around 175 mm long, 12mm OD copper pipe with colour coding all as specified and directed.

Supply, install and testing of Gas Outlet Point with prove Amico type for Vacuum copper stubs around 175 mm long, 12mm OD copper pipe with colour coding all as specified and directed.

Supply, install and testing of Gas Outlet Point with prove Amico type for Nitrous oxide copper stubs around 175 mm long, 12mm OD copper pipe with colour coding all as specified and directed.

Supply, install and testing of Gas Outlet Point with prove Amico type for Air copper stubs around 175 mm long, 12mm OD copper pipe with colour coding all as specified and directed.

Supply, fixing and testing of Isolation Valve chromium plated brass with adapter ball valve type working temperature (-30 degree to 180 degree) for 12 MM OD pipe all as specified and directed.

Supply, fixing and testing of Isolation Valve chromium plated brass with adapter ball valve type working temperature (-30 degree to 180 degree) for 15 MM OD pipe all as specified and directed.

Supply, fixing and testing of Isolation Valve chromium plated brass with adapter ball valve type working temperature (-30 degree to 180 degree) for 22 MM OD pipe all as specified and directed.

Supply, fixing and testing of Isolation Valve chromium plated brass with adapter ball valve type working temperature (-30 degree to 180 degree) for 28 MM OD pipe all as specified and directed.

Supply, install and testing of BPC flow meter with humidifier bottel and capacity 1 to 12 lpm with inlet pressure of 50 to 60 psi humidifire 250 CC polycarbonate body all as specified and directed.

Supply, install and testing of ward suction unit with 600ml jar all as specified and directed.

Supply, install and testing of area Alarm System Digital Display for Foul gas with sensor, digital of gas pressure, high and low setting of audio-visual alarm of make NOVAIR/ALVI automation/ENMET, complete all as specified and directed.

Supply, install and testing of valve box with regulator with bypass system for foul gas service all as specified and directed.

Supply, install and testing of HP tube of size 3/8 " of medical grade PVC for Oxygen/vacuum all as specified and directed.

S&F Monitor Tray, wall mounted all as specified and directed.

Supply, install and testing of Oxygen Manifold System wall mounted straight line (6+6) with 12 Tail Pipes, NRV and regulator single Stage( With out cylenders) , pressure reating 145 k.g /sq.cm all as specified and directed.

Supply , installation, commissioning and testing of Automatic Gas cantrol panel for Oxygen three valve outlet flow at 60 psi -1000 LPM for Oxygen with regulator hight pressure isolation valve and vent valve and bypass valve all as specified and directed.

Supply, install, commissioning and testing of (2+2) Oxygen Manifold for emergency with 4 Tail pipes, NRV and regulator double stage ( with out cylender) pressure rating 145 Kg /sq.cm, wall mounting straight line all as specified and directed.

Supply , installation, commissioning and testing of (2+2) Nitrous Oxide Manifold with 4 Tail pipes, NRV and regulator double stage ( with out cylender) pressure rating 145 Kg/sqcm, wall mounted straight line all as specified and directed.

Supply, installation, commissioning and testing of Automatic Gas cantrol panel for Nitrous Oxide three valve outlet flow at 60 psi -1000 LPM for Nitrous Oxide with regulator hight pressure isolation valve and vent valve and bypass valve all as specified and directed

Supply, installation, commissioning and testing of Vacuum Pump system (oil free) compressor with 1000ltr vacuum tank and 7HP motor vacuum switch pressure reducingregulator, amf meter, volt meter and within the system isolation valve and copper piping etc. Vacuum Pump Make: IR/crompton all as specified and directed

Supply, installation, commissioning and testing oil free Air Compressor System make: anestiwata BFT-50C-9 with 5 HP Motor with 1000 ltr Tank Air Manifold 2 Regulator with Filter Air Dryer 10 CFM Micro Filter all as specified and directed.

LPG SUPPLY: NOTE: -The installation of LPG manifold system with accessories and MS pipe line heavy duty for LPG supply shall be carried out in accordance with IS: 6044 Part-I : 2000. The detailed layout diagram of LPG supply pipe line and manifold system to be submitted by the contractor as per the LPG multi cylinder manifold system manufacturers recommendation and LPG supplier.

Supply, installation, testing and comissioning of LPG cylinder manifold system of 5x5 cylinders ( 10 Nos) as per the gas safety guidelines all as specified including all necessary fittings required as per the manufacturers recommendation in consultation with the LPG Supplier.

Supply, installation, testing and commisioning of brass shut off valve 20mm suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines. Make: Suraksha/ UW.

Supply, installation, testing and commisioning of brass clip on adaptor 20mm suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines. Make: Unitech/Suraksha/ UW.

Supply, installation, testing and commisioning of flow leader suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines. Make: Suraksha/ UW.

Supply, installation, testing and commisioning of main line valve 20mm suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines. Make: Acron/Suraksha.

Supply, installation, testing and commisioning of terminal block for 2 ways size 3x8 including necessary fittings suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines.

Supply, installation, testing and commisioning of quarter turn tape 1/1 BSPTM standard nozzle including necessary fittings suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines.

Supply, installation, testing and commisioning of flexible copper pipe 18 " size 12mm including necessary fittings suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines.

Supply, installation, testing and commisioning of variable high pressure regulator as per IS 4786 for LPG including necessary fittings suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines. Make: Unitech/Suraksha/ UW.

Supply, installation, testing and commisioning of brass adaptor including necessary fittings suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines.

Supply, installation, testing and commisioning of flexible rubber pipes ISI marked including necessary fittings of standard length and size suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines.

Supply, installation, testing and commisioning of brass non return valve of size 20mm bore including necessary fittings suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines.

Supply, laying, testing and commisioning of MS pipe heavy duty of size 20mm bore all as per IS 1239 with all standard fittings such as tee, elbows, sockets, joints etc on walls/ floors/ ceiling with suitable size clamps/ clips suitable for the multi cylinder manifold system as mentioned in the above item No 146 all as per the LPG safety guidelines. Make : TATA/ Jindal

AIR CONDITIONING VRF/VRV AC UNITS : NOTES FOR SCOPE AND INCLUSIONS (i) Supply, Instalaltion, testing and commissioning of Variable Refrigerant Flow/Volume (VRF/VRV) (with the latest technology/version) with All-Inverter driven Scroll Compressor, modular type airconditioning system with stepless modulation for both heating & cooling modes, complete with indoor and outdoor units, individual remote controller and centralized controller, interconnected refrigerant piping with insulation within ODU & for circuit, Y joints for ODU & IDU, full charge of refrigerant gas including additional top up and oil, control cabling etc. as per detail given in specifications and having following items. The prices to be given in Indian rupees including all taxes and duties and delievered at site. Refrigerant to be used shall be - R 410 A only. It shall be complete as per technical specifications with multi connection kits for each outdoor unit & first charge of refrigerant gas for the VRF/VRV units & required MS frame work or required foundation & anti vibration pads for mounting the outdoor units. Installation, testing & commissioning of air cooled VRV/VRF system shall include pipe pressure testing & flushing with nitrogen, charging of gas/oil etc. & will include all lifting/shifting etc. (ii) Ducting design for AHU's to surgery rooms and for treated fresh air to rooms where high wall units to be installed will be provided by the contractor as per manufacturers recommendation.(iii) The outdoor unit shall conform to national accreditation board of testing and caliberation laboratory certification. (iv) Detailed layout of electrical wiring, drain piping for condensed water, refrigerant piping etc. shall be submitted by the contrctor for approval before execution as per the manufacturers recommomdations.(v) all items of works as detailed above shall be deemed to be included in the rates of AC items

Make Blue star : -IVRFB-28TCN/THN, 28 HP = 9 No.s and IVRFB-8TC/H, 08 HP = 01 No.

Make O-General: -AJ*252LN*BHH, 28 HP = 9 Nos. and AJ*072LN*BH, 08 HP = 1 No.

Make TOSHIBA: -AP2814TF8-E, 28 HP = 9 Nos. and MAP0804FT8-E, 08 HP =1 NO.

Make HITACHI: -RAS-24FSNS, 24 HP = 10 Nos. and RAS-10FSNS, 10 HP =2 NO.

Supply, installation, testing and commissioning of (Indoor Units - Wall mounted Units) Wall mounted Hi-wall units of following Nominal capacities with fittings, suspension arrangement, as required as per manufacturer's reccommendation. It should be complete as per technical specification. The makes shall be same as of outdoor units.

Supply, installation, testing and commissioning of (Indoor Units - Cassete Units) Wall mounted Hi-wall unit of 3.20 TR capacity with fittings, suspension arrangement, as required as per manufacturer's reccommendation . It should be complete as per technical specification. The makes shall be same as of outdoor units.

Supply, installation, testing and commissioning of (Indoor Units Treated fresh air units) treated fresh air units of following nominal capacities with fittings suspension arrangement in tne ceiling as required as per manufacturer's recommendation for capacity 1000 CFM - 6.8 TR. It should be complete in all respect according to technical specifications. The makes shall be same as of outdoor units.

Supply, Installation, testing and commissioning of (Indoor Units -AIR HANDLING UNITS) of following capacities, factory built floor mounted VRF/VRV compatible double skin type horizontal air handling units made of 25mm thick panels consisting of pre plasticized GI casing of thickness 0.6mm outside layer and plain 0.6mm inside layer with polyurethane foam (PUF) insulationfactory injected between them by injection moulding machine, complete with blower section with Backward cureved DIDW blower suitable for static pressure as required, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.41 mm) cooling coil of 6 row deep, HEPA FILTER SECTION WITH HEPA Filters, inspection door for upstream verification; Return air side,ombination filter section with filters (Pre Filter + fine filter) with filter, belt drive package with TEFC drive motor of efficiency class IE2 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply, drain connections, stainless steel (18G) drain pan with PUF insulation, etc. complete and of following capacities: Note: (i) Price should be inclusive of VRV/VRF compatible kit with suitable capacity starter panels to be installed in AHU room. (ii) Contractor should submit the duct design detail as per the AHU specifications.(iii) The makes of AHU shall be Blue star/Zeco/Carrier as approved by GE.

(a) 10000 CFM - 30 TR capacity, SP - 125mm at ground floor for special surgery 2 & 3, General Surgery 1 & 2.

(b) 18000 CFM - 51 TR capacity, SP - 125mm at ground floor for special surgery 4, 5, 6, 7 & 8 & Dental Hygine surgery - 1

(c) 6000 CFM - 19.5 TR capacity, SP - 125mm at ground floor for special surgery -1 & Dental Hygine surgery - 5 & 6.

(d) 4400 CFM - 11 TR capacity, SP - 125mm at first floor for Dental Hygenist surgery at 2,3 & 4.

Supply, Install of interconnecting following sizes of (Refrigerant Piping for VRV / VRF System) hard/ soft drawn seamless refrigerant copper pipe work as per air conditioning norms with Y-joints/ Headers (considered in a separate item & will be paid under that relevant item) & silver soldering joints as required at site & as per specifications insulated with "O" class closed cell electrometric nitrile rubber tubular insulation of fire retardent grade of conductivity less than 0.22 Btu.in./(h.ft² °F) and density 50 Kg/CMT with thickness 25 mm up to 51 mm dia pipe and with 32 mm for more than 51 mm dia pipe, between Indoor Unit & outdoor units as per specifications. All piping inside the building shall be properly supported on trays and all external piping shall run in covered tray, including tray of suitable size with fixing arrangements. The refrigerant pipe sizes shall be as per manufacturer's standard. It should be complete as per technical specification. Indoor & Outdoor insulation shall be mechanically protected with two layers (07 mm thick each layer) of adhesive and glass cloth/ CSM or manufacturer supplied jacketing and Outdoor insulation shall have two coats of special UV resistant paint.

34.90 mm dia pipe (1.20 mm wall thickness) with 19 mm insulation

28.60 mm dia pipe (1.20 mm wall thickness) with 19 mm insulation

22.20 mm dia pipe (1.00 mm wall thickness) with 19 mm insulation

19.10 mm dia pipe (1.00 mm wall thickness) with 13 mm insulation

15.90 mm dia pipe (1.00 mm wall thickness) with 13 mm insulation

12.70mm dia pipe (0.80 mm wall thickness) with 13 mm insulation

9.50 mm dia pipe (0.80 mm wall thickness) with 13 mm insulation

Supply, installation, testing & commissioning of refrigerant joints from VRF/VRV manufacturers as recommended by OEM for VRF/VRV system with minimum three connections (one inlet and two outlets) all as per specifications and as directed.

Supply, laying, testing and commissioning of (Communication cables) standard copper control cable size as per OEM 2 core 0.75 sqmm, screened sheilded communication cable to have interface between outdoor units/controller to individual unit covered into PVC conduit (HMS quality) to be laid on wall/false ceiling & covered ceiling including clamping and supporting as per standard specifications.

Supply, installation, testing and commissioning of (Condensate Drain Piping With Nitrile Rubber Insulation) condensate drain water piping of GI 'medium' grade complete with fittings like elbows, tees, reducers, bends, MS flanges, supports, welding, painting etc. as required conforming to tender specifications and of following sizes for AHU Complete pipe shall be duly insulated with "O" class Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness in the tender specification & suitable for indoor/ outdoor application. Complete pipe insulation shall also have 200 g/m² factory laminated, treated woven Glass Cloth coating for mechanical/ manufacturer supplied jacketing and UV protection (a) 32 mm dia pipe, 13 mm Insulation.

Supply, installation, testing and commissioning of (Condensate Drain Piping for VRV Hi Wall Unit) 19 mm dia rigid heavy duty PVC piping complete with fittings, support as per drawing and insulated with 6mm closed cell elastomeric insulation with aluminiumised surface complete all as per manufacturer specification and as directed.

All as per item No. 170 above but for 32 mm dia pipe.

Supply, installation, balancing and commissioning of (Rectangular Aluminium Ducting Site Fabrication) site fabricated Aluminum rectangular complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. of sheet thickness 22 Gauge up to 750mm all as per approved drawings and specifications.

All as per item No. 172 above but for thickness 20 Gauge up to 1500mm.

S&F (Duct Insulation) 19 mm thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class “O”) insulation on existing duct. The joints shall sealed with 50mm wide and 3mm thick self adhesive nitrile rubber tape insulation complete all as specified and directed.

S&F (Grilles, Diffusers, VCD) powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers all as specified and directed.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers all as specified and directed.

Supplying, fixing testing commissioning of Fresh / Exhaust air louvers with bird screen & damper all as specified and directed.

Supplying, fixing testing commissioning of Volume control GI Dampers to be provided in Supply/ Exhaust air registers/ terminals

Supply, Installation, testing & commissioning of (Isolators for VRV ODU/ Hi Wall IDU) Isolator switch with ELCB seperately for VRV ODU of suiable capacity with sheet metal enclosure, rain protection etc. as required to suit the site condition Of capacity 63 Amps TPN all as specified and directed.

Single Phase MCB with enclosure of capacity 2-6 Amps 10 KA, 'C' series for VRV/ VRF Indoor Unit all as specified and directed.

Supply, laying, testing and commissioning of (Power & Control Cabling) power and control cabling as per specification given in the tender. XLPE insulated aluminium conductor armoured cables/ power cabling of PVC insulated and PV seathing copper flexible cable of 1.1 KV grade including cable end termination with brass compression glands & aluminium lugs for aluminium conductor armoured cables only etc. all as specified and directed for trhe following sizes:-

(a) 16 sqmm x 4 core copper armoured cable for outdoor Units.

(b) 10 Sqmm x 3 core copper armoured cable for looping indoor units.

(c) 2.5 sqmm X 3 core copper cable from MCB to indoor units.

RO PLANT

S&F HDPE water storage tank of capacity 5000 litres for RO waste/ refused water storage over 1.0m high PCC platform of suitable size for the weight of water storage tank complete all as specified and directed.

Supply, Install, testing and commissioning of Reverse Osmosis Plant of capacity 150 Liters/hours. Pre-Treatment Section : (a) Raw water Feed pump (b) Multigrade sand bed filter and Activated carbon filter pressure gauges to check differential pressure. Fine Filtration & Reverse Osmosis Block : (a) Micron filter. (b) R.O. membrane. (c) High pressure Moter pump. (d) MS Skid with powder coating for mounting RO equipments and controls. Control Instruments : (a) Electrical Control Panel. (b) Heavy Duty Contractor with Timer. (A) DESIGN & CAPACITY : Assumptions : (a) No. of working days: 34 days. (b) No of working hours: 05-6 hours. (c) Inputs (Raw water Quality): Total Dissolved Solids: 1500 PPM. (d) Output (Treated Water Quality) : Total Dissolved Solids: < 50-100. (B) TECHNICAL SPECIFICATIONS : Approx Flow Rate : (a) Feed Water : 400 LPH. (b) Treated Water : 150 LPH. (c) Rejected Water : 250 LPH (The reject flow depends on input water quality). (1) RAW WATER PUMP : Purpose To feed the Dual Media Filter at pressure more than bar, which is min. operating pressure for filter. (Contd......)

Specifications : (a) MOC: CI (b) Centrifugal Pump (c) Flow Rate: 1000 liters per hour (d) Head : 25 m (e) Electrical : 230 V, single phase, 50 hz (f) Cycle: 2900 RPM (g) Make: CRI (h) Quantity : 1 No. (2) SAND AND CARBON MEDIA FILTER : Purpose To remove the total suspended solids, dirt, iron and reduce silt density index which can foul the membrane. Specifications Vessel : (a) Make: CLD (b) Material of Construction: FRP 8x44 (c) Testing Pressure: 10 kg/cm2 (d) Opening : Top & Bottom only (e) Quantity: 2 No Valve : (a) Make: Initiative / Standard or equivalent. (b) Material of Construction: Noryl (c) Type: Multiport Single lever value (d) Size: 15 mm (e) Maximum Flow Rate: 1000 LPH (f) Working Pressure: 2-4 Bar. Media : Mixed bed sand media consisting of the following (a) Gravel (b) Pebbles (c) Quartz Sand (d) Activated Carbon media Average : (i) Porosity 50 micron particulate size (ii) Bed depth: 600 mm (iii) Pipelines & Accessories: Upvc. (3) MICRON FILTER : Purpose To remove the fine particles up to 05 microns and reduce silt density index levels to acceptable level. Specifications Cartridge Filter & Housing : (Housing) : (a) Make: Kemflo/ Paintair/ Hitech (b) MOC of Housing: PP (c) Length: 20” (d) Diameter: 2” (e) Quantity: 1 No (Cartridge) : (f) Make: Kemflo, Pentair (g) Cartridge MOC: Polypropylene (h) Length: 20” (j) Diameter: 2” (k) Quanity: 1 No. (l) Micron rating: 05 micron. (4) HIGH PRESSURE PUMP : Purpose To feed the Reverse Osmosis Membrane at pressure more than the osmotic pressure taking into consideration flux rate, flow and recovery. Specifications : (Contd....)

(a) Type: Centrifugal Horizontal type (b) Flow Rate: 1000 liters per hour (c) Pressure: 10 Kg/sqcm (d) Cycle: 2900 rpm (e) Make: CRI (f) Quantity: 1 No. (5) RO MEMBRANE : Purpose To remove the major part of TDS upto 98% by Reverse Osmosis. Membranes arranged and designed to give adequate flow and recovery. Specifications : (a) Type: Spiral Wounded (c) Length of Membranes: 1m. (d) No of Membranes: 1 (e) Recovery per Membrane : 15-17% (f) Salt Rejection per Membrane: 98-99% (g) Make of Membranes: LG (h) System Recovery: 40-50%. (6) RO PRESSURE TUBE : Purpose To pack Reverse Osmosis Membranes and operate at high pressure upto 200-300 psi. Specifications : (a) MOC: FRP (b) Diameter of Pressure Vessel: 4 inch (c) Length of Pressure Vessel: 1.2m (d) Pressure Vessels: 1 No. (e) Membrane per Vessel : 1 No. (f) Make: Imported (g) Position: Horizontal.

Dasmesh Buildcon

M/s Khanna Enterprises

Agarwal Jagdish Construction Company Private Limited

MANGLA AMIT BUILDERS PVT LTD