PROVN OF ENERGY EFFICIENT LED SECURITY STREET LIGHTS ONLINE UPS WITH BATTERY DESERT COOLERS AND THREE PHASE TAMPER PROOF CT OPERATED LT ENERGY METER AT JASAI MIL STN UNDER GE ARMY BARMER

Amount

Material and labour for prestressed cement concrete poles 9 M long of size 102x172 mm at top and 102 x 279 mm at bottom class-10, conforming to relavent latest IS complete all as specified and directed at site. NOTE: P.C.C Work , excavation and earthwork will be measured and paid separately under relevant item.

Supply and fix loop type insulator, vitreous porcelain white brown or green , over all dimension 90x140 mm and clearance of hole 25.5 mm complete all as specified & directed.

Supply and fix pin type porcelain insulator , vitreous white brown or green including one galvanised mild steel spindle two GI washer and GI Nuts 100 mm height 65 mm dia for 1100 volts grade complete all as specified & directed.

Supply and fix shackle type porcelain vitreous white insulator 1100 volt grade 75 mm in height and 90 mm dia including galvanised mild steel strap of size 31x3mm , 12 mm dia insulators bolts, washers and nuts complete all as specified & directed.

Earthing complete with galvanized steel earth plate electrodes 60x60x6 mm thick buried directly in ground earth (earth pit not less 2.25 m deep below ground level) with top edge of the plate not less then 1.5 mtr below normal ground level connected to galvanised iron earthing strip 32mm x6mm thick by means of bolt nuts check nuts and washers of galvanized iron or steel all as specified & shown in electrical plate No.3 of MES SSR part-I 2009 connected to earth test point as specified and testing on completion including provision of 40 mm dia light grade pipe up to 7.5 mtr length as protection & watering pipe shall be 20 mm bore medium grade including all excavation & earth work in any type of soil incl PCC pit (1:3:6) type C-1 with RCC cover including charcoal , salt, funnel, all as directed at site. NOTE:- Rate included for excavation & earth work in any type of strata as shown in electrical plate No 3.

Material and labour for galvanised iron earthing strip 32 mm x6 mm laid in trenches / fixed on wall for inter connecting /extension in earthing including excavation and earth work complete all as specified & directed.

Material and labour for stay assembly complete with 30x 30x 6 mm thick plate and 16 mm dia stay rod all as shown in elect plate NO-1 of SSR-part -1 including stay wire of 7/2.50 mm dia of suitable length all as specified & directed .

Material and labour for ACSR conductor straightening properly on insulators and binding with aluminum taps /binding wire /conductor jumper etc complete all as specified & directed.

Material and labour for steel structure, cross arms bracing supports ,clamps, back plates of any type, section incl. nuts, bolts, washers, welding ,bending cold or hot in any size and shape all as directed Including two coats of aluminium paints over a coat of red oxide primer incl preparation of surface all as specified & directed

Material and labour for cradles, hexagonal/rectangular fabricated with GI earth wire 4 mm dia and cradles made out of 3.15 mm dia GI wire all as specified & directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, erection of poles, struts/stays, leveling of yard etc not exceeding 10 M² on plan and not exceeding 1.5 m in depth and getting out in Soft/disintegrated rock.

Excavation in trenches not exceeding 1.5 m wide and exceeding 1.5 m in depth upto 3.0 m for erection of poles, struts/stays, leveling of yard etc not exceeding 10 M² on plan and getting out in any type of rock.

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm in Soft/disintegrated rock.

Removing of excavated soil not exc. 50 M from starting points all as specified & directed.

Material and labour for Cement concrete (1:4:8)Type D2 using 40 mm graded stone aggregate for foundation of pole /struts/stay assembly etc completeall as specified & directed.

Material and labour Cement concrete (1:3:6) type C -1 using 20 mm graded stone aggregate set in cement motor 1:6, for pedestal of poles/copping including necessary frame work ,fair finishing to exposed surfaces using extra cement complete form all as specified & directed.

Supply and fix LED Street light fitting 60 Watts, 230 V, 50 HZ, suitable for operation over voltage range of 140 V to 270 V, duly housed in pressure die cast housing with toughned glass, comprising of LED with individual optical lens, electronic driver with THD <10%, efficacy >110LPW and PF more than 0.90, confirming to IP66, rendering color index of > 75 with cool day light output. incl. suitable size three core aluminium conductor PVC cable from gear / control box to fitting through PVC conduit or along with suitable size three core aluminium conductor for connection of street light fitting to LT OH line / Junction Box etc complete all as specified and directed. MAKE :- Havells/Crompton/ Wipro.

Supply and fix of GI pipe Bracket of 40 mm dia light grade pipe bend to shape of approx length 1.5 Mtr incl 2 Nos. MS Clamp of flat iron of suitable size complete with nut , bolt, washers MS Clamps of flat iron of suitable size (not less than 25 x 3mm) Including two coats of aluminium paints over a coat of red oxide primer all as specified and directed.

Supply and fix of Steel tubular 11.0 metres long swaged pole type 410 SP-55 complete with cast iron base plate, finial toper plug, nuts, bolts and screws all as specified and directed.

Material and labour for fixing of Flood light fitting LED type 150W capacity pressure die cast aluminium housing with toughned glass complete including secondary lenses with IP66 protection, system efficacy greater than or equal to 120LPWwith 10KV SPD connecting with neutral phase and earth FRLS PVC sheathed wires 1.5 sqmm upto junction box all as specified and directed and as per Make Havells/Crompton/Philips

Supply and Laying cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm 2 core as specified and directed. Make: Havells/Finolex/Gloster

Supply and fixing on pole of GI pipe Bracket of 50 mm dia medium grade pipe bend to shape of circular form and 40 mm dia as supports all as directed of suitable length complete with nut , bolt, washers and all accessories all as specified and directed.

M& L for Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, erection of poles, struts/stays, levelling of yard etc not exceeding 10 M² on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil as specified and directed.

M&L for sand cushioning to U/G cable for cushioning 8cm below the cable and 15cm above cable all as specified and directed. Note: Punned thickness shall only be measured for payment purpose.

Material and labour for stone slab(Patti), roughly hammer dressed stone, 40 to 50 mm thick, 25 to 30 cm wide and not less than 60 cm long laid dry and abutting each other with gap between adjacent slab not exceeding 10 mm over underground cables for protection as specified and directed.

Returning, filling in, including spreading, levelling watering and well ramming in layers n.exc 25 cm in soft/loose soi as specified and directedl.

Removing of excavated soil not exc. 50 M and depositing where directed at a level n. exc 1.5 M above the starting points as specified and directed.

Supply and fixing of GI pipe of light grade for protection of cable under road/pole and panel of size 40 mm as specified and directed

Supply and fix SPN / DP enclosure,single phase of four way double door as specified and directed. Make: ABB/Legrand/Siemens.

Supply and fixing MCB SPN, C curve type of 20 amp make : ABB/Legrand/Siemens

Supply and fixing MCB SP, C curve type of 10 amp make : ABB/Legrand/Siemens

Supply, install, testing and commissioning of 10KVA / 192VDC Online UPS (Single Phase IN & Single Phase OUT) with Double Conversion high Freq. Switching PWM, using IGBT's. Voltage Range : 160V AC~270V AC ±5V AC, Frequency - 45~55Hz , THD (Liner Load):<3%, THD (Non-Liner Load) - <5% , Overload Capability : 125% for 2minuted / 150% for 30Seconds, Pure Sine Wave, excluding batteries Inbuilt Manual Bypass,Inverter Efficiency: 90% on rated full load , Overall Efficiency : 80%, Panel with LED for UPS status and LCD for Voltage, Current & Frequency. with average backup time of 30 min complete all as specified and directed . Make - HITACHI / TATA LIEBERT/ MICROTEK.

Supply, install, testing and commissioning 12V/26AH SMF Battery with UPS complete all as specified and directed . Make: Exide/Amron/Microtek

Supply and install suitable size Battery Stand and Interlinks of Batteries complete all as specified and directed .

Supply and fix SPN MCB DB metallic Double Door 8 way with 200 amps rated bus bar as specified and directed.Make: Legrand/ SEIMENS/Schneider.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning as specified and directed. Make: Legrand/ SEIMENS/Schneider. SP 5 To 32 AMP

All as per Srl Item no 36 above but SPN 40 to 63 AMP

Supply and fixing Single Core Cable with copper conductor PVC round sheathed (flexible) industrial cable 1100 volts grade with multi stranded conductor of size 10 sqmm including necessary thimble, lugs and clips complete all as specified and directed . Make: Polycab/ Havells/ Finolex.

M & L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to and including galvanized earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion and excavation and earth work in any type of soil, PCC 1:3:6 type C1 in chamber, precast RCC cover 50mm thick in cement concrete 1:2:4 type B1, reinforced with welded steel wire fabric or XPM with cast iron frame, funnel with wire mesh, 20mm bore GI pipe medium grade watering pipe, lugs, 40mm bore GI pipe medium grade protection pipe upto 7.5m. NOTE : Item includes the cost of earth lead and GI protection pipe upto 7.5m. GI wire beyond 7.5m shall be measured and paid for separately.

Supply and fix desert cooler electric driven (single phase), having nominal air flow capacity of 4000 CuM per hour (or nearest size) made of Steel body. bottom water tank faricated out of 18 guage sheet ,Cooler Body Pre Coated Galvanized Sheet 1mm (20 SWG) front grill/side columns/side panels,desert cooler motor 900RPM Fan Diameter 450mm, Exhaust Fan Heavy Duty, single phase, Submersible Heavy Duty pump, with Cooling Media,Water Tank Capacity 55 Ltrs .

M&L for Electronic Tamper proof, digital LT CT operated (3 phase AC) multifunction DLMS compliance energy meter of accuracy class 0.5s, 3x240V, 50Hz with optical & RS 232 Port, backlit LCD display, measures and display trivector energy, load survey, TOD, tamper detection & logging, power ON/OFF events, instantaneous parameters comprising of active energy (KWH), Apparent energy (KVAH), Average voltage per phase, Average current per phase etc. of rating 200/5A with display in absence of power with 4 CTs of 200:5 ratio unbreakable, fire resistant, non flammable & non hygroscopic, transparent extended terminal block cover polycarbonate plastic (ETBC) including connection with suitable size copper conductor cable as per latest IS complete all as specified and directed by Engr-in-Charge. Note: Rates inclusive of CTs and connected thimbles etc.

S & F Electronic Tamper proof, digital LT CT operated (3 phase AC) multifunction DLMS compliance energy meter of accuracy class 0.5s, 3x240V, 50Hz with optical & RS 232 Port, backlit LCD display, measures and display trivector energy, load survey, TOD, tamper detection & logging, power ON/OFF events, instantaneous parameters comprising of active energy (KWH), Apparent energy (KVAH), Average voltage per phase, Average current per phase etc. of rating 100/5A with display in absence of power with 4 CTs of 100:5 ratio unbreakable, fire resistant, non flammable & non hygroscopic, transparent extended terminal block cover polycarbonate plastic (ETBC) including connection with suitable size copper conductor cable as per latest IS complete all as specified and directed by Engr-in-Charge. Note: Rates inclusive of CTs and connected thimbles etc.

Material and labour for sub main wiring with 4x10.0 sq. mm + 2x6.0 sq. mm earth wire nominal cross sectional area, 1100 Volts grade, stranded, FRLS- FLEXIBLE WIRING CABLE. CONFORMING TO IS: 694-1990 PVC insulated, unsheathed copper conductor cable Make:- Finolex/Gloster/Havell's and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all MS accessories / fittings, brass screws, washers etc and connected to common earth dolly including all cutting / chases etc in Existing panel, making good to panel etc including painting etc to the disturbed surfaces to match the existing surface complete all as specified & directed.

Supply and fix sheet metal enclosure LT panel with appropriate size of electric cable/wire (Outdoor) type factory made, weather proof , dust and vermin proof (IP 54) suitable for 1100 V/660 V grade 3 phase 50 HZ AC supply floor mounted , fabricated out of 3.00mm MS sheet welded on 40 mm x 40 mm x 5 mm angle iron frame / base of appropriate size grouted in PCC 1:3:6 foundation and having angle iron legs made out of 40 mm x 40 mm x 5mm, angle iron below frame with front door opening having locking arrangement provn for copper conductor PVC insulated flexible suitable wire size / extension strips and connected with suitable size thimbles , lugs duly painted with grey epoxy powder coating after suitable chemical treatment, legs duly embedded in ground in PCC 1:3:6 of suitable size including necessary earth work and civil work locking arrangement suitable for mounting , with required sheet metal enclosures, thimbles , and all other electric incoming and outgoing connections as required complete all as specified and directed .

National Rewinding Works

M/S SACHCHANATH POWER SUPPLY AND ENGINEERS SUNDRA

Devi Engineeing