REPAIR/ MAINT TO FLOORING, TILING, PLINTH PROTECTION, ROOF TREATMENT (INCL LEAKAGE AN SEEPAGE RECTIFICATION), MASONRY WORK, PLUMBING WORK, SANITARY FITTING, CHAJJAS, PARAPETS, FASCIA ROOF PLASTER, JOINERY AND MISC WORK IN OTM ACCN AND CENTRAL INSTIT

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed by Engr-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete or lime concrete (unreinforced) in ground floors and Pavings not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed by Engr-in-Charge.

M&L for Demolition of RCC of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of brick work , built in cement mortar or cement lime mortar including all quions, arches, pillars, etc including demolition of precast rcc articles and disposal of debris out of MoD land complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc including necessary scaffolding up to four storeys height of bldgs if required and removing of debris out of MoD land complete all as specified and directed by Engr-in-Charge.

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed by Engr-in-Charge.

Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed by Engr-in-Charge.

Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar,and taking out of trenches, if required, internal dia of pipe in 75MM/100mm complete all as specified and directed by Engr-in-Charge.

Taking down eaves gutter and rain water pipe any size any pattern , PVC/ AC pipe including all fittings ,heads shoes, bends etc including removal to store ,Internal dia of pipe in 75MM/110mm complete all as complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without taking off shutters from the freme)complete all as specified and directed by Engr-in-Charge.

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each and removing from site complete all as specified and directed by Engr-in-Charge.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each and removing from site complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass ( any thickness, size, quality or description ) from wooden frames or stone concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engr-in-Charge.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engr-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.& Brushing neat cement slurry with 3.0kg of cement per sq metre complete all as specified and directed by Engr-in-Charge.

M&L for joint free non skid coloured Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for joint free non skid coloured Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in skirtings, dados and risers to step etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick cement plastere in CM 1:4 complete all as specified and directed by Engr-in-Charge. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for Vitrified Ceramic tiles 10 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for Vitrified Ceramic tiles 10 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in skirting, dados etc etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:3 complete all as specified and directed by Engr-in-Charge. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for coloured Glazed ceramic tiles in vertical surface such as wall,dado etc 450mmX 300mmX 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:3 complete all as specified and directed by Engr-in-Charge. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for joint free non skid coloured Ceramic tiles 08mm to 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for non-abrasive paving (endura) tiles 300mm x 300mm x10mm thick (square/ rectangular) polished, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over & including 15mm screed bed CM 1:4 to match complete all as specified and directed by Engr-in-Charge. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles and Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.& Brushing neat cement slurry with 3.0kg of cement per sqm.

M&L for Providing and laying 60mm thick factory made glossy finish, chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete all as specified and directed by Engr-in-charge. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks & laying pattern approved by GE.

M&L for Providing and laying 80mm thick factory made glossy finish,chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engr-in-charge. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks & laying pattern approved by GE.

M&L for 16-18 mm thick granite (pure black) work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite over including 20mm thick screed bed or bedding layer in cement mortar 1:4 etc complete all as specified and directed. Note:- The stone slab shall be in one piece over kitchen plateform,window cill and making gas pipe holes 25mm dia with rounded holes and all open edges to be half rounded complete all as specified and directed by Engr-in-Charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base 20mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar including cement plaster 10mm thick in CM 1:3 complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm thick Cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) as in,sub base, sub floor etc, complete all as specified and directed by Engr-in-Charge. Note:- Finishing surfaces of concrete to be even and rough to receive the topping layer or floor tiles etc.

M&L for 25mm thick Cement concrete in sub base for receiving floor tiles and mass concrete using Type B-1,1:2:4 (using 20 mm graded crushed stone aggregate) complete all as specified and directed by Engr-in-Charge. Note:- Finishing surfaces of concrete to be even and rough to receive the topping layer or floor tiles etc.

M&L for 40 mm thick plain cement concrete type B-1, 1:2:4 (using 20 mm graded curshed stone aggregate) finished even and smooth without using extra cment as in flooring complete all as specified and directed. Note- Glass dividing strips shall be measured and paid separately as supply only)

Supplied only 38 mm wide and 3 mm thick glass dividing strips in flooring by fixing in position and making square or rectagle for casting concrete in flooring complete all as specified and directed by Engr-in-Charge.

M&L for Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified and directed by Engr-in-Charge.

M&L for RCC type B-1 (1:2:4) using 20 mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like such as cover slab of septic tank/soak well etc complete all as specified and directed by Engr-in-Charge. Note:- Reinforcement shall be measured and paid separately).

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and directed by Engr-in-Charge.

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and directed by Engr-in-Charge.

M&L for precast reinforcement cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate, in cover slabs (for manholes etc.) chulla hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge. (Reinforcement shall be measured and paid separately).

M&L for burnt clay brick work with sub-class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for burnt clay brick work with sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces of wall in cm 1:4 mixed with liquid water proofing compound as per manufacturer's instructions, finishing surfaces even and smooth without using extra cement including scaffolding if required, complete all as specified and directed by Engr-in-Charge.

Supply only `Liquid Water Proofing Compound complete all as specified and directed by Engr-in-Charge.

M&L for rendering 10 mm thick on other than fair faces of brick work or concrete surfaces of wall in cm 1:6 finishing surfaces even and smooth without using extra cement including scaffolding if required, complete all as specified and directed by Engr-in-Charge.

M&L for Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:3) as on ceiling complete all as specified and directed by Engr-in-Charge.

M&L for Providing and applying Birla/Altek wall care putty of 1-2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered internally surfaces of wall and applying one coat of primer (as per manufacturer’s recommendations) on the surfaces and applying two coats of distemper oil emulsion finished without any brush marks on the surface in any colour including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and directed by Engr-in-Charge.

M&L for Preparing newly plaster surfaces of wall & applying two coats of cement base paint over a priming plastered and other surfaces with alkali-resistance Primer without any brush marks on the surface in any colour including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old plastered internally surfaces of wall and applying one coats of distemper oil emulsion finished without any brush marks on the surface in any colour including necessary scaffolding if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old plastered surface and apply one coat of acrylic water based exterior grade emulsion @ 0.9 ltr ( undiluted)/10sqms diluted with water in 1:1 ratio finished without any brush marks on the surface in any colour including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

Fixing only 15mm bore old Steel water tubing including all new galvanized fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed by Engr-in-Charge. Note: - Old Steel water tube/pipe any type retrieved from taking down shall be used along with all new GI fittings)

S&F 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

Fixing only 20mm bore old Steel water tubing including all new galvanized fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed by Engr-in-Charge. Note: - Old Steel water tube/pipe any type retrieved from taking down shall be used along with all new GI fittings)

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubing or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete all as specified and directed by Engr-in-Charge.

S&F in repair Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F in repair Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F in repair Ball valves 20 mm bore high pressure of PTMT with epoxy coated aluminum rod & high-density plastic ball screwed for iron pipe & fixed. (min. weight 15mm-142 gms) complete all as specified.

S&F Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including inlet & outlet tank nipple 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and directed by Engr-in-Charge.

S&F Rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including inlet & outlet tank nipple 20 mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm bore fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair 15 mm bore long body CP Bib taps cast copper alloy fancy type with capstan heads,and cup screwed down, high pressure for iron pipe complete, all as specified and directed by Engr-in-Charge.

S &F in repair of stop valve/angle cock fancy type cast copper alloy, chromium plated with capstan head serewed down high pressure for 15 mm dia iron pipe complete all as specified and as directed.

S&F in repair stop valves (ISI marked), 15mm dia, cast copper alloy,chromium plated fancy type with long shank and cup(concealed type) screwed down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed by Engr-in-Charge.

S&F in repairs Brass CP shower rose 125mm size with rubit cleaning system including fixing to steel pipe or union, complete all as specified and directed.

S&F in repairs Sheet/corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed by Engr-in-Charge.

S&F Toilet paper holder with flat recessed type stainless steel complete all as specified and directed by Engr-in-Charge.

S&F in repair stainless steel Soap dish, fixed to plugs with chromium plated brass screws fixing arrangement, complete all as specified and directed by Engr-in-Charge.

S&F in repairs of brass chromium plated health faucet with 1m long PVC tube & wall hook. screwed for 15mm dia bore iron pipe or 2 in one tap complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm dia 450 mm long PVC connection including brass check nut at both ends screwed both end for iron pipes complete all as specified and directed by Engr-in-Charge.

S&F in repairs of 15mm bore brass chromium plated wall mixer with provn of overhead shower with 115mm long bend pipe on upper side, connecting legs & wall flanges for mixing hot and cold water, screwed down, high pressure complete all as specified and as directed.

S&F in repairs Brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm bore complete all as specified and directed by Engr-in-Charge.

S&F in repair sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 160mm including waste coupling of 32/40mm size complete all as specified and directed by Engr-in-Charge.

S&F in repairs Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia 'D' type Brass Chromium plated incl brackets, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed by Engr-in-Charge.

S&F in repairs Tubular towel ring, ISI marked round edge/shape, Brass Chromium plated incl brackets, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous China wash down water closet pan including P or S trap of bore 125/110 mm (pedestal pattern), white or in matching colour of tiles (excluding flushing cistern ) including flush pipe of polythylene of low or high density or PVC 32 mm dia, for low level cistern including plastic water closet seat, white or in matching colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and wash down water closet complete all as specified and directed by Engr-in-Charge.

S&F in repair viterous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, witht integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. including flush pipe of polythylene of low or high density or PVC 32 mm dia, for low level cistern complete including making good to floor complete all as specified and directed by Engr-in-Charge.

S&F in repairs 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets ,flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed by Engr-in-Charge.

S&F in repairs for Viterous China urinal, half stall type, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement and waste pipe (excluding flushing cistern, flush pipe ) complete all as specified and directed by Engr-in-Charge.

S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed by Engr-in-Charge.

S&F Vitreous china urinal partition white of size 310x700 mm complete all as specified and directed by Engr-in-Charge.

S&F in repairs Viterous China wash basin, white, flat back, size 550x400mm excluding taps etc but including brackets,including cutting for and pinning in ends of brackets or erecting stand including waste coupling of 32/40mm bore and waste pipe complete all as specified and directed by Engr-in-Charge.

S&F in repairs of single Piece-WC with UF soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings Size: 360x725 x735 mm, S Trap-300 mm white with combined flush tank (Cascade type) including seat covers complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engr-in-Charge.(ISI MARKED)

S&F PVC (SWR) bends 75 mm bore any radius, complete all as specified & directed.

S&F PVC (SWR) bends any radius 110mm dia complete all as specified and directed by Engr-in-Charge.(ISI MARKED)

S&F in repairs 75 mm PVC floor trap, ISI marked with CP grating with/without waste pipe hole incl jointing to waste pipe fixed with solvent cement, complete all as specified and directed by Engr-in-Charge.

S&F pressed steel frames 165 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including one shop coat of primer complete all as specified and directed by Engr-in-Charge.

S&F pressed steel frames 105 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including one shop coat of primer complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete type C-0, 1:3:6 using 12.5 mm graded crushed stone aggregate as in back filling of hollow portion of frame with plain cement concrete and for fixing of hold fast complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, confirming to IS-2202 (part-1-1999), ISI marked complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge. Note: wire cloth shall be measured separately

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed by Engr-in-Charge.

S&F factory made particle board core solid panel PVC door shutter of walnut colour, 28 to 30mm thick (stile) with 2, 4, or 6 raised panel design with 2mm thick moulded prelam PVC sheet on front side face and 2mm thick plain colur olour PVC sheet on back face supplying & fixing at site as specification & drawing in SSR Part-II, section 8, clause 8B.4, complete all as specified & directed.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling fixing in opening as per specification & drawing complete all as specified and directed by Engr-in-Charge.

S&F 3mm thick sheet glass ordinary/frosted quality and glazing clip/oil putty/beading in square exc 0.5 sqm in each pane upto tripple story building complete all as specified and directed by Engr-in-Charge.

S&F 3mm thick ordinary/frosted glass, pin head type and glazing clip/oil putty/beading in square n-exc 0.5 sqm in each pane upto tripple story building complete all as specified and directed by Engr-in-Charge.

S&F in repairs of steel window/ventilator factory made, made out of mild steel box type and shutter suitable for double shutter i.e. glazed and gauged shutter. Glazed shutter made out of hollow section with sash bar and gauged shutter made out of hollow section without sash bar including hinges, tower bolt, handle, grill 10mm sq bar including two coat of synthetic enamel paint over one coat of red oxide primer, atrred hold fasts, PCC bed blocks for fixing hold fast, including plain/ figured glass and stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.18mm & fixed with stainless steel wire staples etc complete all as per drg No CEPZ/ C-TD/032/13 Sheet No 1/1 & 2/2 including taking down old windows/ventilators, complete all as specified and directed.

S&F Powder coated (of approved color) aluminium sections as in frame & shutter of Door, windows, ventilators as in sliding / openable / louvers / fixed type with and including necessary rolling for smooth moving & locking arrangement, etc. fixed to wall including, preparation of disturbed portion both sides (internal & external surfaceof wall) match with existing surface treatment and all sides of aluminium frame shall be sealed with silicon sealent (inner/outer face) complete all as specified as directed by Engr-in-charge.

S&F stainless steel butt hinges of size 100mm long for fixing of pvc door shutter etc complete all as specified and directed by Engr-in-Charge.

S&F Powder coated Aluminium, anodised, barrel tower bolts of extruded section and fixed, length of bolt in 200mm complete all as specified and directed by Engr-in-Charge.

S&F Powder coated Aluminium handles, cast type, anodised Size of handle in 300mm complete all as specified and directed by Engr-in-Charge.

S&F Anodised Aluminium, anodised, barrel tower bolts of extruded section and fixed, Length of bolt in 200mm complete all as specified and directed by Engr-in-Charge.

S&F Anodised Aluminium handles, cast type, anodised Size of handle in 150mm complete all as specified and directed by Engr-in-Charge.

S&F Anodised Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed Length of bolt in 250 mm complete all as specified and directed by Engr-in-Charge.

S&F 5.5 mm thick sheet glass ordinary/tinted/frosted quality and glazing with neoprene rubber gasket/clip/oil putty/beading in square n.exc 0.5 sqm in each pane upto tripple story building complete all as specified and directed by Engr-in-Charge.

S&F 5.5 mm thick sheet glass ordinary/tinted/frosted quality and glazing with neoprene rubber gasket/clip/oil putty/beading in square exc 0.5 sqm in each pane upto tripple story building complete all as specified and directed by Engr-in-Charge.

S&F in repairs of 2 lever brass mortice lock, vertical type, size 100 mm complete all as specified and directed.

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate including welding to steel framescomplete all as specified and directed by Engr-in-Charge.

S&F in repairs of door closer aluminium (extruded section body) hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed

S&F in repair ACP sheet 4mm thick, for fixing in aluminium frame including necessary fittings and fixtures, complete all as specified and directed by Engr-in-Charge.

M&L for 18 to 20 mm thick PVC prelaminated solid board with one side decorative choice laminate and other side balancing white including 3mm thick lipping and equal to thickness of board as in kitchen cabinet, cupboard etc fixed with screws to steel/timber frame work etc complete all as specified and directed by Engr-in-Charge.

S&F for Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed by Engr-in-Charge.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and directed by Engr-in-Charge.

S&F hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, Size of hasp and staple in mm 100 complete all as specified and directed by Engr-in-Charge.

S&F Continuous (piano) hinges 30mm Width of flaps (when open) ,mild steel, bright finish or electrogalvanised complete all as specified and directed by Engr-in-Charge.

S&F in repair of peg set of 4, brass chromium plated, fancy type, superior quality and fixed with screws complete all as specified and directed by Engr-in-Charge.

S&F in repairs of stainless steel curtain rod 20 mm dia, 1mm thick with SS bracket and SS domes at end, heavy duty,complete all as specified and directed by Engr-in-Charge.

S&F in repair of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

M&L for repair or tightening of loose Aluminium doors/windows, changing old damaged rubber beadings and cleaning/repairing of floor spring/hydraulic door closer etc, complete all as per specified and directed by Engineer-in-Charge.

M&L for cutting down vegetation growths like plants / trees of girth not exc 15 cm & surface are not exc 0.36 Sqm each from roof tops /sides of external walls of buildings, chajja, wall junctions, junctions of rain water / soil /waste vent pipes including taking out roots entered in wall/slab surfaces and making good the surfaces including repairing the CI/GI/PVC joints of affected locations by applying TUFALO chemical (herbal medicine ) to arrest further growth and making good to suit the adjoining surfaces using PCC type 1:2:4, type B-O or cement mortar 1:2 complete all as per manufacturer instructions and as specified. NOTE: Any CI/GI/PVC pipes and fittings damaged during work shall be replaced by new one to insure leakage / seepage free joint without any extra cost to the department and Unit rate quoted by tenderer shall included for use of all scaffolding, trestles, ladders, cradles etc, hoisting, lowering and protective measures etc up to four storeys height of bldgs and removing of debris out of MoD land complete all as specified and directed by Engr-in-Charge.

M&L liquid water proofing treatment to RCC roof non acceessible/acceessible slab including dismantling of existing roof treatment of any description such as worn-out tar felt, debris, mortar of any description & any thickness, surface cleaning of all foreign material such as shrubs/roots, fungus, moss, dust including plaster, APP membrane etc. including disposal of debris out of MoD land in low laying area, in following procedure : (a) Prepare the surface by cleaning with concrete surface grinder/ wire brush and a high pressure water jet and ensure that it is free of dust, oil and loose particles. Damaged portions, hollow area must be repaired with epoxy mortar and repair cracks of old concrete by cutting 'V' groove, corners and joints of drain pipes, channels etc. treated with epoxy mortar prepared with epoxy primer (as per manufacturer's instructions). (b) Laying 10mm thick screed in Cement mortar 1:3 including and mixing with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of concrete roof surfaces, finished even and fair to receive treatment on roof Complete (c ) Applying three coats of polyurea waterproofing coating as per manufacturer's instructions for maintaining minimum dry film thickness 1.5mm and elongation at break of free film of approx. 500% ± 50% and tensile strength at 14 days of 5MPa. (e)The materials shall be applied with brush or roller, complete in all respect as per the direction of Engineer-in-charge / Consultant. (Note:- minimum 6hrs interval between two coat shall be maintained) (f) All auxiliary and accessories involved during application should be supplied by single manufacturer as a part of system. Note: - (i) Work to be carried out by authorized applicator and as per manufacturer’s instructions. (ii) Providing test with filling of water for continuous 48 hours if there is any leakage than entire treatment will be done again by contractor without any cost. (iii) The rate includes for filling cracks in existing roof with epoxy cement mortar using suitable bonding agent before laying cement plaster.”

S&F false ceiling with fibre cement designer tiles ivory painted (high pressure steam cured) of 4mm thickness (as per IS:14862) of size 595 x 595 mm and any one of the design (occeanic, lake & hill, cascade or electra) in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main 'T' runnerwith suitably spaceed joints to get required length, and 15x32 mm made of 0.30 mm sheet, and cross 'T' at 600 mm c/c to form a grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to exising rafter, purlin, etc with galvanised butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15 mm of all T-sections shall be centra black pre-painted with polyester paint, and havng a load bearing capacity of 12Kg/sqm, and refixed all existing electric wiring and fixture all complete at all heights as per direction of Engineer-in-Charge

S&F 5mm thick insulated PVC wall lining honeycombed (HL series) consisting of PVC insulated panel with approved colour & design printed PVC sheet used colour PVC sheet duly fitted into the wall including PVC sheet in strips feathered at the edges including removing & refixing electric switch boards & plates & covered with PVC strips or beadings after fixing wall panelling as per specification complete all as specified and directed by Engr-in-Charge.

Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 77,799.00 and any other reduction if any from quoted amount.

HARI OM ENTERPRISES (BID ID -3452222)

Substantial Const. Co. (BID ID -3460732)