PROVN OF 02 x TOILET NEAR GUARD ROOM AND CERTAIN MINOR AND REVENUE WORKS UNDER AGE B/R-II AND AGE E/M OF GE SOUTH DELHI CANTT-10

Amount

M&L for Cutting holes through brick wall exc. half brick and not exc. 1 brick built in cement mortar for inserting hold fast and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required, complete all as specified and as directed.

M&L for cutting chases, pinning in , making good to facings where required and pointing in cement mortar 1:3 to ends or edges or landings, steps, cills, sunshades,shelves,lintel,etc and cutting in chases for concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth, complete all as specified and as directed.

M&L for steel work in tubular trusses including special shaped washer, cleats etc complete using ERW or induction butt welded tubes confirming to IS: 1161-1979 grade st - 240 complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description , not otherwise described , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer including complete all as specified and as directed.

S&F of Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F of Powder coated aluminium (minimum thickness of powder coating 50 micron) aluminium work for doors, windows, ventilators and partitions for fixed portion with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete all as specified and as directed.

S&F of Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows& ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed. Note: Glazing and paneling to be paid for separately under respective item of BOQ.

S&F of aluminium composite panel (ACP) in any colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick), fixed with aluminium beading in aluminium window/ventilators etc complete all as specified and as directed.

S&F powder coated aluminium snap grid frame work of size 605 x 605 mm and 2-3 mm thick (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long and including acoustic gypsum perforated tiles 4 mm thick of size 600x600 mm fixed in ceiling or laid/ inserted to Aluminium snap grid, complete all as specified and as directed.

Surface dressing not exceeding 15 cm deep in any type of soil complete all as specified and as directed.

M&L for 100 mm thick cement concrete (1:4:8) Type D-2, (40 mm graded crushed stone aggregate), as in sub-base of floor and similar works complete all as specified and as directed.

M&L for cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate as in holdfasts, coping on edges etc including weathering slightly rounded or chamfered angles and throating as directed including necessary formwork complete all as specified and as directed.

Supply and laying of 60 mm thick factory made chamfered edge cement concrete interlocking paver block of M-35 grade confirming to IS 15658-2006 with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;

Excavation in post holes in hard / dense soils , each not exceeding 0.50 cum, getting out, returning filling in and ramming earth in layers not exceeding 25 cm including watering & removing surplus soil to a distance not exc. 50m & making good surface complete all as specified and as directed

M&L for cement concrete (1:3:6) Type C-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

S&F 4 mm thick fibre glass reinforced translucent plain sheeting of any colour and pattern fixed with coach screw and washer in wall , complete as specifed and as directed.

M&L for Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-410 grade-E-250, complete all as specified.

Surface excavation in soft/loose soil, not exceeding 30 cm deep and averaging 15 cm deep and getting out, complete all as specified and as directed.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5m in depth in any type of soil and getting out, complete all as specified and as directed.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above starting point complete all as specified and as directed.

Returning filling in including spreading, levelling watering and well ramming in layers not exceeding 25 cm each layers, complete all as specified and as directed.

M&L for providing cement concrete 1:4:8 type D2 (Using 40mm graded stone agg) in foundation, mass concrete and filiings complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in sub base to floors, finished even complete all as specified and as directed.

M&L for hardcore of gauge not exceeding 63 mm deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface for plinth protection/path complete all as specified and as directed.

M&L for factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

M & L for preparation of new or previously untreated plastered/concrete surfaces of any description over 10cm girth or width, not other wise described incl two coats of synthettic enamel paint complete all as specified and as directed.

M&L for Mild steel Framed work such as framing of posts or struts for fencing or fixing for WPC Jali , grills, gratings etc. with ends of bars shouldered and or bolting/ riveting/ welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including cutting top to ashape as directed, holdfasts or screws etc; MS tubing confirming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F of Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite) JALI of required size comprising of virgin PVC resin of K Value 58-60 (Suspension Grade), Calcium Carbonate and natural fibers (Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cum , having good screw holding capacity (Screw Withdrawal strength of 2000 N ( Face ) & 1100 N (Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC Jali to be fixed with WPC Frame of size 70x45 mm/ MS frame and stainless Steel butt hinges ( if required ) of required size with necessary full body threaded star headed counter sunk SS Screws complete all as specified and as directed.

S&F of mild steel screw bolts (machine made) with hexagonal head at one end and screwed the other or screwed both ends each screwed and to be fitted with washers and with hexagonal nut of exc 5 cm length with dia of shanks 11 to 15 mm etc complete all as specified and as directed.

M&L for Mild steel framed work as in doors or gates in ornamental and intricate design of flat, angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-290 grade-E-165, complete all as specified.

M & L for preparing new steel surfaces and treating ends of posts etc., with coal tar black paint area tarred exc .10 Sqm but not exc 0.50 Sqm each complete all as specified and as directed.

M&L for reinforced cement concrete M-25 Design mix as in footing, foundation,beams, plinth beams, base for columns and mass concrete etc complete all as specified and as directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter for rough finished surface of concrete, complete all as specified and as directed.

M&L for reinforced cement concrete M-25 (Design Mix) as in columns and pillars etc complete all as specified and as directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions of square, rectangular or polygonal shape for fair finished surface of concrete, complete all as specified and as directed.

M&L for providing reinforcement cement concrete M-25 (Design Mix) as in Beams, cantilevers, ressummers, lintels over 1.5m span concrete etc complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface of concrete, complete all as specified and as directed.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

M&L for from work to soffits of suspended slabs such as roof slabs, floor slabs, landing & similar work not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces, complete all as specified and as directed.

M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide complete all as specified and as directed.

M&L for mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including muld seel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

All as per item no 42.00 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, complete all as specified and as directed.

Material & labour for brick work with sub class B old size burnt bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4 complete all as specifie and as directed.

M & L for half brick thick brick work with sub class B old size burnt bricks straight or curved on plan to any radius in walls built in cement mortar 1:4 complete all as specifie and as directed.

M&L for rendeing 10 mm thick with rady mix plaster on fair faces of brick work finished even and smooth without using extra cement complete all as specified & directed.

M&L for rendeing 15 mm thick with ready mix plaster on stone masonary surface other then fair faces surfaces finished even and smooth without using extra cement including scaffolding arrangement to carry out the work complete all as specified & directed.

M&L for rendeing 5mm thick with ready mix plaster on ceiling surfaces finished even and smooth without using extra cement and scaffolding arrangement to carry out the workcomplete all as specified & directed.

M&L for preparation of newly plastered surfaces of wall/ceiling sufraces and applying two coats of oil bound distemper on wall/ceiling surfaces over a coat of primer and 1mm thick cement based putty using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall/ceiling sufraces and applying two coats of super quality weather proof exterior emulsion paint over a coat of primer and 1mm thick waterproof cement based putty using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base to floors, finished even complete all as specified and as directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-1 (Using 20mm graded crushed stone aggregate), as in sub base in floor/paving etc complete all as specified and as directed.

M&L for non skid coloured ceramic tiles jointless 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 for laying floor finish complete all as specified and as directed.

M&L for glazed ceramic coloured tiles 350mm x 250mm x 7 mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match in vertical surfaces such as skirting /dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10m thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing coat complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2, using 40mm graded crushed stone aggregate as in plinth protection, surface finished even and smooth without using extra cement including sacure drain of suitable size along the plinth protection, complete all as specified.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65 x100 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.

S&F of 100 mm long AISI 304 stainless steel butt hinges fixed with stailess steel screws or welding with any type of frame complete all as specifed and directed.

S&F of AISI 304 stainless steel handles 125mm long fixed with stainless steel screws complete all as specifed and directed.

S&F of AISI 304 stainless steel tower bolt 100mm long fixed with stailess stell screws complete all as specifed and directed.

S&F of 250mm long AISI 304 stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, complete all as specifed and directed.

S&F of aluminium ventilator with outer frame 40mmx114mm with 1.3mm thickness corner 45 degree cut & aluminium welded center mullion size 40mmx65mm partly glazed/ gauzed including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws , MS wire mess , 3mm thick sheet glass etc. provision for fixing the exhaust fan complete all as specified and as directed.

S&F of 4.0 mm thick frosted sheet glass ordinary quality and glazing with oil putty in square n.exceeding 0.5 Sqm in each panes complete all as specified and as directed.

S&F of Vitreous China wash down water closet (Pedestal pattern), white with ‘P’ or ‘S’ trap, fixing with screws of suitable size, plastic seat cover, white closed pattern with flat bottom and cover, complete all as specified, making connections to trap and to flush pipe etc. and making good to floors, complete all as specified.

S&F of PVC valveless, syphonic action type flushing cistern, 10 litres capacity, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long, complete all as specified.

S&F of white vitreous china flat back half stall urinal of size 580x380x350 mm with white 5 litre PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, floor trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required complete all as specified and as directed.

S&F of vitreous china wash hand basin flat back size 550x400 mm size white excluding taps waste chain and plug and porcelain stopper but including brackets and 32 mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32mm X 600 mm long PVC waste pipe complete flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S & F in repair PVC connection 15 mm bore 45 cm long with 2 Nos brass check nuts with washer complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank of 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position and making necessary holes for inlet, outlet and overflow pipes but with fittings such as tank connection and ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe of size 20mm dia etc, complete all as specified and as directed.

S&F of bib taps, fancy type, chromium plated, with crunch or butterfly handle screwed down,screwed for iron pipe or for brass ferrule and fixed of 15mm bore size complete all as specified and as directed.

S&F of Pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered `Hot’ or `Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm dia, complete all as specified.

S&F stop cock fancy type chromium plated, screwed down, high presure with cruntch or butterfly handle screwed both ends for iron pipe of 15mm bore pipe complete all as specified and as directed.

S&F of 15 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 with fittings complete all as specified ( brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor etc) union, ball valves, flange and tank adaptor in trenches/floor/wall/ceiling complete all as specified and as directed.

S&F of 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 with fittings complete all as specified ( brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor etc) union, ball valves, flange and tank adaptor in trenches/floor/wall/ceiling complete all as specified and as directed.

S&F 110 mm uPVC pipes Type 'A', single socketed, in any length with rubber ring joints, laid in trenches or in floor or fixed to walls, complete all as specified and as directed.

S&F 110 mm uPVC (SWR) Bends/Tee type ‘A’ (any radius), complete all as specified and as directed.

S&F of holder bat clamps 110mm bore out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, complete all as specified and as directed.

M&L for Salt-glazed stoneware gully traps 100mm x 100mm, square or roun mouthed floor trap, plain with grating including jointing with solvent cement of 100mm dia complete all as specified and as directed.

S&F CP grating of size 100mm dia complete all as specifed and directed complete all as specified and as directed.

M&L for granite (of any type) work, 18 t o 20 mm thk (table rubbed and polished) in steps,jambs,pillars, window-cills, cooking platforms and like in 20mm thick screed bed cement screed bed 1:6 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed.

Supply only Liquid water proofing compound of approved quality complete all as specified and as directed.

M&L for precast reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in cover slab etc set laid and dry, including provision of necessary formwork, complete all as specified and as directed

M&L for 150 mm internal dia salt glazed stone ware drain pipes laid in trenches and jointed complete all as specified.

M&L concrete bed to 150 mm bore drain pipes in cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified.

M&L for 100 mm thick PCC 1:3:6 type D-2 (Using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

S&F 12 to 15mm thick heavy duty parking tiles of any colour, any pattern any desing as approved by GE, area of each tile exceeding 0.04 Sqm but not exceeding 0.36 Sqm as in floors/landing/steps/riser/parking/ footpath etc and over & including 15 mm thick screed bed or bedding/ rendering layer in cement mortar 1:4, including jointed with neat cement slurry and pointed in coloured cement to match the surface of tiles, complete all as specified and directed

M&L for point wiring complete with single core multi strand copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 Volts grade electrical cable in and including new PVC conduit on surface medium grade and sunk in factory made pressed steel modular terminal boxes 2mm thick of required size and modular front & back plate of approved colour/model of suitable size for housing the modular switches, sockets and fan reulators with all accessories including 1.5 Sqmm single core with multi strand copper conductor PVC unsheathed cable earth and connected to earth dolly complete all as specified for following :- Note 01:- New conduit with connected accessories will be laid if there is damage in existing conduit and the rates are inclusive of quoted rates. Note 02:- the rate is inclusive of cutting/chasing and making good the disturbed surface with CM 1:3 and the same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/white wash complete.

One light /fan point controlled by one way switch

S&F switch 6 Amps modular type,1M with red indication single pole one way, ISI marked complete all as specified and as direected.

Supply and fixing LED lights fitting 1x 10W, 220V, 2 feet, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm, complete all as specified and as directed.

S&F LED bulkhead light fitting, 10 Watt, white colour, housing made of high-grade flame-retardant engineering plastic with clear prismatic diffuser, suitable for wall or ceiling surface mounting. The fitting will be provided with replaceable LED lamp (cool white) and include all required mounting accessories.Connected with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required from ceiling rose, complete all as specified and directed.

S&F of sheet metal enclousure for DB's where MCB's to be used Single pole and Neutral 4 way ,240 volts, double door bus bar neutral link,earth bar and din rail.

S&F of MCB SPN 63 Amps 'C' curve 240 volts, breaking capacity 10 KA suitable for lighting and other domestic loads complete all as specified and directed.

S&F of MCB SP 6 to 32 Amps,'B' curve 240 volts, breaking capacity 10 KA suitable for lighting and other domestic loads complete all as specified and directed.

Supply, laying, connecting and testing XLPE insulated, armoured, heavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 4 Sqmm 2 core and making end termination with aluminium lugs and with supporting nuts/bolts laid in trenches or passing through pipes/ducts or fixed to walls/poles, complete all as specified. Note: Earth work, brick protection and sand cushioning shall be measured and paid for separately

M&L for Sand cushioning to underground cables provided with a layer of sand 8cm thick before laying the cable in trenches and 15cm thick after laying the cable in trenches complete all as specified and directed. Note : For measurement purpose punned thickness 18cm shall be considered.

S&F of 25 mm bore GI tubes, medium grade galvanised, with all fittings and fixed complete laid in trenches or laid floors or concealed, complete all as specified and as directed.

M&L for excavation by trenchless boring technology for holes under road pavement, hardstanding using ultrasound techneque and engaging necessary machine including HDPE pipe 200 mm dia complete all as specified and as directed.

M&L for sub class B brick well burnt for cable protection laid flat with length equal to width of brick over cable, complete all as specified and as directed.

M&L for Boring holes under road pavement by bocky manually in any type of soil upto 200 mm bore complete all as specified and as directed.

Supply and laying GI tubing light graded 40 mm bore fixed to walls and ceiling or laid in trenches complete all as specified and as directed.

H S KALSI AND BROS (BID ID -3512712)

CHAUDHARY CONSTRUCTIONS (BID ID -3510798)