CONSTRUCTION OF LABS UNDER PM SHRI SCHEME AT KENDRIYA VIDYALAYA MANAURI AT AF STN MANAURI

Amount

Surface excavation n.exc 30cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation in over area n.exc 1.5m depth and getting out in soft/loose soil as in foundation complete all as specified and as directed.

Excavation in over area exc 1.5m depth but n. exc 3.0 m depth and getting out in soft/loose soil as in foundation complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.50 m wide and not exceeding 1.50 m in depth as in foundation, laying of cables and getting out including trimming of sides complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.50 m wide and exc 1.5m depth but n. exc 3.0 m depth as in foundation, laying of cables and getting out including trimming of sides complete all as specified and as directed.

Returning, filling in, including, spreading, leveling, watering & well ramming in layers not exceeding 25 cm complete all as specified and as directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5M above the starting point complete all as specified and as directed.

M&L for providing PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation, as in surface channels and drains filling and mass concrete etc complete all as specified and as directed by Engr -in-Charge.

Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter finished rough surface of concrete complete all as specified and directed.

Use and waste of formwork to sides of columns, pillar, post ,piers, struts square or rectangular or polygonal finished rough surface of concrete complete all as specified and directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs etc. also splays between floors and beams, etc finished rough surface of concrete complete all as specified and directed.

Use and waste of Formwork to chullah hoods, chajjas, troughs and similar items including edges finished rough surface of concrete complete all as specified and directed.

Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) finished rough surface of concrete complete all as specified and directed.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide complete all as specified and directed by Engr-in-charge.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5 cm but n.exc 10 cm wide complete all as specified and directed by Engr-in-charge.

M & L for mild steel TMT bars 10mm dia & over cut to length bent to shape required including,crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed by Engr -in-Charge.

M & L for mild steel TMT bars 6 to 8mm dia cut to length bent to shape required including,crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed by Engr -in-Charge.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) as in foundation including raft , footing, foundation beams and plinth beam complete all as specified and as directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) as in slab supported on walls, beams in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) as in chajjas and similar work complete all as specified and as directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) as in beams, cantilevers,bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) as in columns, pillar, post ,piers, struts complete all as specified and as directed.

M&L providing, cement concrete type B1 using 20mm aggregate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing ourses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks(old size bricks) straight or curved on plan exceeding 6 mtr mean radius built in cement mortar 1:4 and external face of brick work pointed flush in the same mortar as the work proceeds, complete as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in Cement mortar 1:6 and finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for applying two coats of Plastic emulsion paint with 2mm putty on walls over coat of primer on new plastered surfaces including necessary preparation of surfaces complete all as specified and as directed.

M&L for Rendering 15mm thick plaster in CM 1:4 on surface other than fair faces of brickwork finished even & smooth without using extra cement complete all as specified and as directed.

Material and labour for waterproof cement based putty @ 1 Kg (undiluted ) per sq mtr. of average thickness 1mm over the plastered by skilled labour complete all as specified and as directed.by Engineer-in-Charge.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives@ 1.43 litre/ 20 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm complete all as specified and as directed. by Engineer-in-Charge.

M&L for rendering 5 mm thick on ceiling surface as in Cement mortar 1:3 and finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new surfaces and applying three coat of a white wash on ceiling complete all as specified and as directed.

M&L for preparation of surfaces and priming the surface with one coat of cold applied bituminous primer @ 0.25 ltr /sqm conforming to IS: 3488 & apply a layer of APP based polymeric membrane 3 mm thick (min) weighing 3 Kg / Sqm reinforced with polyester non woven febric (weighing not less than 150 gms / Sqm) applied by torch application having side over lap 75 mm and at the end 100 mm including sealing the joints and application of bituminous aluminium paint in two coats @100gm/Sqm in each coat complete all as specified and as directed by Engineer in Charge. Note : Membrane shall be taken to a height of min 60 cm and inserted in a groove on parapet wall where required and shall be deemed to include in the quoted rate.

M & L for Pressed steel frames for door frame of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc complete all as specified and as directed

M&L for PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate for fiiling of hollow section complete all as specified and as directed

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floor and for fixing of hold fast etc complete all as specified and as directed.

M&L for 35 mm thick 2nd class hard wood glazed and skelton door shutter, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for scuring glass, etc.; sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed

M&L for 30mm thick flush door shutters solid core construction, with block board core and plywood face panels, commercial type on both side fixed to chowkhat complete all as specified and as directed.

M&L for Butt hinges 100mm long medium weight, colled rolled mild steel complete all as specified and as directed.

M&L for Aluminium, anodised, barrel tower bolts of 200 mm long and 10mm dia stove enamelled black with bright bolt fixed complete all as specified and as directed

M&L for extruded aluminium alloy handles 125mm size fabricated type anodized ISI marked complete all as specified and as directed.

M&L for two Coats of synthetic enamel paint over a coat of pink primer surfaces of any description, over 10cm in width or girth,not otherwise described in new wooden surfaces complete all as specified and as directed.

M&L for sliding bolt 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

M&L for anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary oining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C-1 using 20 mm graded stone aggregate in plinth protection laid in alternate bays and joint filled with bituminious mastic complete all as specified and as directed.

M&L for broken stone hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed.

Supply only liquid waterproofing chemical ISI marked.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for Sand filling under floors or in foundations spreading and levelling in layers n exc. 25cm thick including watering and consolidation complete all as specified and as directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base under floor complete all as specified and as directed.

M&L for 25 mm thick PCC 1:2:4 type B-1 as in levelling coarse for tiles.complete all as specified and as directed.

M&L for double charged vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm,over and including 15mm thick screed bed in cement mortar (1:6) in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and as directed.

M&L for double charged vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm,over and including 10mm thick screed cement mortar (1:4) in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and as directed.

M&L for preparation of new steel surface exceeding 10 cm width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed by the Engineer-in-Charge.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and as directed by the Engineer-in-Charge.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

S&F for powder coated aluminium doors frames and shutters fixed or side hung including jointing cleat for fixing including all fittings like handles, locks, hinges, stoppers, latches etc complete all as specified in Drg No CE (AF)/NGP/03/TD/32, Sheet 1/2 to 2/2.

S&F for Vitreous China wash basin, white, flat back, of size 550x450mm including brackets(flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply compete all as specified and as directed.

S&F for waste pipe for wash hand basin 32mm/40mm dia compete all as specified and directed.

S&F for powder coated aluminium grills of approved design and pattern, with approved standard section fixed to the window frame all as specified by Engr-in-Charge

S&F for Rotational moulded polethelene water storage tanks in 500 litres capacity (cylindrical triple layered white coloured vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I complete, ISI marked, all as specified and as directed.

S&F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F for PVC (SWR) 75mm floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F for 110mm PVC (SWR) WC connector with lip ring complete all as specified and as directed.

S&F for PVC (SWR) 110 mm bends any radius complete all as specified and as directed.

S&F for PVC (SWR) 75 mm bends any radius complete all as specified and as directed.

S&F for 110mm PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F for 110mm PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F for chromium plated bottle trap 32mm dia having minimum water seal of 25mm complete all as specified and as directed.

S&F for pillar tap 15mm dia cast copper alloy with clutch or butterfly handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F for stop valve 15mm dia cast copper alloy with clutch or butterfly handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F 15 mm bore tubes medium grade galvanized with all fitting and fixed complete to walls and ceilings or laid in floors of any length complete all as specified and directed.

S&F 20 mm bore tubes medium grade galvanized with all fitting and fixed complete to walls and ceilings or laid in floors of any length complete all as specified and directed.

S&F for soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S&F for 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F for tubular towel rail 20mm dia 'D' type, 600mm long of CP fixed with and including CP brass screws and wooden/plastic cleats complete all as specified and as directed.

M & L for 5.5mm thick tinted sheet glass, ordinary quality and glazing with oil putty, wooden beading, rubber gasket, aluminium snap beading in area exc 0.5 Sqm in each pane complete all as specified and as directed.

S& F galvanized mild steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or glavanized wire stables, beads or in steel windows complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.complete all as specified & as directed

Add or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete, using extra cement, ncluding forms, moulds, mi- tred/stopped ends etc.complete all as specified & as directed.

M&L for Providing precast cement concrete type B-1 (1:2:4) using 20 mm grade aggregate set in 1:4 cement mortar in but in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, complete all as specified & as directed.

Material and labour for point wiring including fixing on concealed on surface of wall and steel structure/ truss etc rigid non-metallic PVC conduit pipe medium grade, ISI marked heavy duty in size 20 mm dia, with 1.5 Sqmm insulated unsheathed, FRLSH multi stranded copper conductor cable, confirimg to IS 694 single core 1100 volt grade with flush cast iron/ pressed steel/ PVC modular terminal boxes (as per site) of suitable size for fixing of modular accessories such as switches, sockets and fan regulators etc including modular cover plate in required modules and colour and including FRLSH insulated & unsheathed 1100 volts grade cable with multi stranded copper conductor of size 1.5 Sqmm as continous earth wire complete including making good the disturbed surfaces for the followiing:- Note;- (i) Quoted rate shall include cutting, chasing, plastering , colouring etc to surface of wall / beam/ roof etc match with existing surface.(ii) Cover plates with frame shall be measured and paid separately under respective item as S&F .

One light / Fan/bell point controlled by one way independent switch.

One 2/3 pin 5 Amps socket out let point on same board controlled by one switch.

One 2/3 pin 5 Amps socket out let point on independent board controlled by one switch.

All as per above item No 84 here in before point wiring for 15 Amps socket outlet independent using 2.5 Sqmm copper cable FRLSH for phase and neutral and 2.5 Sqmm as earth wire complete all as specified and as directed.

All as per above item No 84 here in before power point wiring using 4 Sqmm copper conductor cable FRLSH insulated unsheathed copper conductor of 4 Sqmm as earth wire complete. Note : All circuit shall be taken from separate control DBs (connected with energy meter) to be connecting individual power load.

Supply and fixing modular type power unit single phase 220 volts 32 Amps socket and control switch ISI marked 4 module complete

Supply and fixing modular switch, one way 6 Amps 1 way module complete all as specified and directed.

Supply and fixing modular switch, one way 16 Amps 1 way module complete all as specified and directed.

Supply and fixing modular 2/3 pin 6 Amp socket outlet 2 way module complete all as specified and directed.

Supply and fixing modular 3/5 pin 16 Amp socket outlet 2 way module complete all as specified and directed.

Supply and fixing ceiling rose surface type 65 mm x 50 mm, 2 to 3 terminal complete all as specified and directed.

Supply and fixing modular fan regulator step type, 120 watt - 2 module complete all as specified and directed.

Supply and fixing white cover plate with frame for modular switch and socket of 2 module complete all as specified and directed.

Supply and fixing white cover plate with frame for modular switch and socket of 3 module complete all as specified and directed.

Supply and fixing white cover plate with frame for modular switch and socket of 6 module complete all as specified and directed.

Supply and fixing white cover plate with frame for modular switch and socket of 8 module complete all as specified and directed. Note applicable for item no 87 to 97:- The colour of modular accessories shall be approved by AGE(I) in writing

Material and labour for sub main wiring with Two runs of single core PVC FRLSH IS-694 cable with colour code unsheathed multi-stranded copper conductor of size 6 Sqmm and drawing through in concelead rigid non metallic PVC conduit pipe 20 mm dia medium grade heavy duty with all necessary fittings including one run of FRLSH insulated unsheathed stranded copper conductor cable of size 6 Sqmm as earth wire (green in colour) and connected to common earth dolly complete all as specified and as directed. Note : (i) Three run of 6 sqmm cable and one run of PVC conduit pipe shall be measured against one unit. (ii) Cost of cutting /chasing/ plastering /colouring etc to match with disturbed surface shall deemed to be included in the quoted rate.(iii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item

Material and labour for sub main wiring with Two runs of single core PVC FRLSH IS-694 cable with colour code unsheathed multi-stranded copper conductor of size 4 Sqmm and drawing through in concelead rigid non metallic PVC conduit pipe 20 mm dia medium grade heavy duty with all necessary fittings including one run of FRLSH insulated unsheathed stranded copper conductor cable of size 4 Sqmm as earth wire (green in colour) and connected to common earth dolly complete all as specified and as directed. Note : (i) Three run of 4 sqmm cable and one run of PVC conduit pipe shall be measured against one unit. (ii) Cost of cutting /chasing/ plastering /colouring etc to match with disturbed surface shall deemed to be included in the quoted rate.(iii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item

Supply and fixing LED recessed mounted down (Ceiling light 2'X2' )36W light fitting energy saving low glare high power mounting on two Nos PVC round/ square block on surface of wall / beam etc incl making all electric connection using three core copper cable drawn through in PVC flexible counduit pipe from ceiling rose to fittings and connecting up complete with 3 core flexible cable white of size 23/0.0076 and making necessary connection complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED Tube light fitting 20 watt 4 feet with PVC batten, compact appearance suitable for Retrofit LED Tube 20 watt including LED tube rod 20 watt self ballasted retrofit lamps with thermoplastic body 270 degree wide distribution CCT 6500 K including fitting fixed on wall/ceiling and connecting up complete with 3 core flexible cable white of size 23/0.0076 and making necessary connection complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED tube light fitting with frame, driver etc in 10 W 2 feet long white colour mounting on two Nos of PVC round/ squire block on surface of wall / beam etc incl making all electric connection using three core copper cable drawn through in PVC flexible conduit pipe from ceiling rose to fittings and connecting up complete with 3 core flexible cable white of size 23/0.0076 and making necessary connection complete all as specified and directed by Engr-in-Charge.

Supply and fix sheet metal enclosure distribution board TPN, 4 poles ,double door, 4 way with 200 Amps rated bus bar vertical type with MCCB 4 pole 100 Amps 415 volt thermal magnetic base operated as incomer incl concealed in surface of wall and making all connection using gland , thimbles in required size complete all as specified and directed Note; Quoted rate shall be inclusive of cost of MCCB , cutting plastering , colouring to surface of wall to be concealed etc all site required matching with existing surface.

Supply and fix sheet metal enclosure for MCB distribution board SPN, single door, 8 way with 200 Amp rated bus bar 230 Volts incl concealed in surface of wall and making all connection using gland , thimbles in required size complete all as specified and directed Note; Quoted rate shall be included cutting plastering , colouring to surface of wall to be concealed etc all site required matching with existing surface.

S&F MCCB , 415 volt TPN 4 poles 63 Amps ,16 KA breaking capacity, thermal based adjustable type complete all as specified and directed

S&F MCB , SPN, 2 pole 215/220 volts , 40 Amps , "C" Curve 10 KA. complete all as specified and directed

S&F MCB , single pole 215/220 volts , 10-32 Amps , "C" Curve 10 KA.complete all as specified and directed

S&F 10 W LED bulk head light fittings incl making all electric connection and connecting up complete with 3 core flexible cable white of size 23/0.0076 and making necessary connection complete all as specified and directed by Engr-in-Charge.

Supply fixing 150 watt LED flood light fitting for replacing with High mast tower / pole in any lenght/ specification ,energy saving IP 65 protection ,required nut bolt washer etc including 3 core flexible cable white of size 23/0.0076 drawn through in PVC flexible conduit and making necessary connection complete all as specified and directed by Engr-in-Charge.

S&F of steel tubular swaged poles 9.00 mtrs long type 410 SP-31 confirming to IS - 2713 Prt I to III 1980 complete with cast iron base plate, nuts, bolts finial taper plug including PCC foundation in (1:3:6) type C-2 using 40mm graded stone aggregate and PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in coping for poles including necessary form work(straight curve) and finishing to all exposed surfaces of concrete including necessary earth work and excavation including applying two coat of aluminum paint over a coat of red oxide primer on pole and painting 03 Nos band/ strip with black, yellow, synthetic enamel paint in alternate layer and pole numbers (30 cm wide each at distance of 30 cm from plinth block including writing numbers with white paint above 1.5 Mtr above ground level over black painted surfaces complete all as specified and directed. Note : Earth work, cement concrete will be incuded in quoted unit rate

Material and labour for sand cushioning with a layer of sand 8 cm thick before laying of cable and 15 cm thick after laying of cable in trenches complete all as specified. Note: Punned thickness shall be measured for payment.

Supply and laying old size sub class 'B' bricks laid flat in trenches over the cable with the length of brick perpendicular to the direction of cable length, adjacent/abutting each other for cable protection complete all as specified and directed.

Material & labour for cutting /boring to plinth protection/ hard standing / road etc in suitable depth to across the GI pipe size upto 40/50 mm dia of bore for drawn through XLPE under ground cable for cable protection complete all as directed. (Note : Quoted rate shall include the cost of required material for repairing to disturbed surface complete all as per existing site and all as directed by Engineer-in-charge.

Supply and laying 50 mm bore galvanized steel tubing "light grade" with all fittings,suitable size MS clamps 4mm thick 15cm width bolts, nuts and washers (ISI Marked) and fixing to the pole , laid in trenches/fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Supply, laying, jointing and testing underground cable of size 95 Sqmm 3.5 core, 1100 volts grade, XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with multi-stranded aluminium conductor laid in trenches, passing through pipe, ducts and making electrical connection with including suitable size lugs proper crimped by crimping tool, thimbles, glands, GI Nuts and bolts, washers, insulation tape etc complete all as specified and directed.

Supply, laying, jointing and testing underground cable of size 25 Sqmm 4 core, 1100 volts grade, XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with multi-stranded aluminium conductor laid in trenches, passing through pipe, ducts and making electrical connection with including suitable size lugs proper crimped by crimping tool, thimbles, glands, GI Nuts and bolts, washers, insulation tape etc complete all as specified and directed.

Supply, laying, jointing and testing underground cable of size 10 Sqmm 2 core, 1100 volts grade, XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with multi-stranded aluminium conductor laid in trenches, passing through pipe, ducts and making electrical connection with including suitable size lugs proper crimped by crimping tool, thimbles, glands, GI Nuts and bolts, washers, insulation tape etc complete all as specified and as directed.

Supply and fixing BLDC ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE Five star rated with brushless direct current motor omplete with 3 core flexible cable white of size 23/0.0076 and making necessary connection complete all as specified and directed by Engr-in-Charge.

Supply and fixing exhaust fan 300 mm sweep steel body heavy duty with louver mounting bracket ISI marked BEE 4 star rated energy saving less noise capacitor type including plastering, colour coating etc and all site required work for disturbed surface matching with existing and making electric connection using three core flexible copper conductor 23/0.0076 cable complete all as directed.

S&F shock proof, fire retardant rust proof, out door pole kiosk box of size 310x210x120mm made out of one piece Engineer plastic moulding of siemens grey colour with in built 4 aluminium strip of 100Amp rating fitted on DMC unbrakable insulator with MCB SP 10Amp including clamps for fixing arrangement complete all as specified and directed by Engineer-in-charge.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete including all accessories complete all as specified and directed by Engineer-in-Charge.

Airways Enterprises (BID ID -3114539)

M/S Garg Sons (BID ID -3101457)

Abhinav Builders (BID ID -3106113)