Reinvited for Upgradation of Primary Health Centre into Health and Wellness Centre at Village Ballambha in Rohtak

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing. (b) In cement. (HSR 8.5 (b)

Removing doors and windows (wooden and steel) together with the dismantling of walls:- (HSR 8.17)

(a) Door

(b) Windows

Scraping. (a) White wash and colour wash. (HSR 8.32 (a)

Scraping. (c) Cement plaster. (HSR 8.32 (c)

Terracing consisting of tiles 22.86cm x 11.43cm x 3.81cm, laid over 87.50mm mud filling on a layer of 25mm mud plaster and another layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg per Sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16. (HSR 13.50)

Cement concrete 1:2:4 gola 10cm x 10cm quardrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR 13.64)

Providing & fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed Tiles 300 x 450mm of reputed manufacturer like: - RAK, NITCO, KAJARIA shall be used as approved by Engineer-in-charge. (HSR 14.92 (b) Note: - The agency to whom the work is allotted will have to produce original bill/ voucher for all quantity in token of proof of purchase of material.

Cement pointing 1:2 deep variety on brick and Tile work. (HSR 15.60)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.3)

Applying priming coat with metal primer on New steel or iron work including preparation of surface. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.9)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Preparation of plastered surfaces for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler,consisting of white lead, linseed oil, varnish and chalk mittii including finishing Preparation of plastered surfaces for oil bound distemper including sand papering. (HSR 16.52)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (b) 1st Quality. (HSR 16.79 (b)

Cost of brass fittings complete for doors and windows, such as tower bolts, handles, etc, and screws for these fittings (excluding sliding bolt). (HSR 17.70)

i) Single leaf door shutter

ii) Double leaf door shutter

Providing and fixing sliding bolt with nuts and screws etc. complete. (HSR 17.83)

(a) brass.

(i) size 300 mm x 16 mm.

(ii) size 250mm x 16mm.

Factory manufactured panelled door or glazed window shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to IS specification No. 1003, kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail, 200mm wide bottom rail and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (b) 35mm thick. (HSR 17.90 (b) - Note 17.18 (i)

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to IS specification No. 1003, kiln seasoned) with 100mm wide vertical styles 150mm wide lock rail 200mm wide bottom rail and wire gauze of 140G or 120G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (styler and rails of windows shutters shall be 75mm wide). (b) 35mm thick. (HSR 17.92 (b) - Note 17.18 (i)

Factory manufactured solid flush door shutters, with block board core as per IS 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot pressed, confirming to IS 2202 part I and II, fixed in position, including iron hinges, screws, chocks/ cleats and stops, etc (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (a) commercial veneering with vertical grains or corss bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (iii) 35mm thick. (HSR 17.93 (a) (iii) - Note 17.18 (i)

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12)

Pressed steel sheet frames (chowkats), consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete:- (HSR 18.34)

(a) door and window frame of size 89mm x 50mm with 40mm wide single rebate.

(c) door and window frame size 127mm x 50mm with 40mm wide double rebate.

NS items

Providing & laying required size of glazed tiles with DESIGN PRINTED for display of Logo (Satinfinish) in dado set in CM 1:3 with joints so as to form a true & even surface and joints finished neatly with white cement mixed with matching pigments all complete as directed. (Rate should include base plastering with CM 1:5 of required thickness). The rate shall include cost of customized printing at top of the tile all complete as the details given by National Health Mission Haryana/ HLL directed. (Kindly refer tender documents for Design details).

Providing & laying required size of glazed tiles with DESIGN PRINTED for Windows & Door Borders (Satin finish) in dado set in CM 1:3 with joints so as to form a true & even surface and joints finished neatly with white cement mixed with matching pigments all complete as directed. (Rate should base plastering with CM 1:5 of required thickness). The rate shall include cost of customized printing at top of the tile all complete as the details given by National Health Mission Haryana/ HLL directed. (Kindly refer tender documents for Design details).

P.H. works

Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type Orissa or Orya water closet suite for Sinking into floor, with raised foot treads complete with 100mm H.C.I, ‘P’ Trap with or without vent as required and all other necessary fittings as fully described in item no.30.1 above. (a) Size 580mm. (i) White. (HSR 30.2 (a) (i)

Providing and fixing in position best Indian make (as approved by the Engineer-in-charge) European type water closet suite, Syphonic type, Consisting of- (i) Vitreous chinaware Syphonic Suite with 15 litres capacity matching chinaware cistern and all internal brass fittings complete with ‘P’ or ‘S’ trap with or without vent (as approved by the Engineer-in-charge). (ii) One piece Seat and lid in hollow black or white plastic fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge). complete in all respects including cutting and making good the walls and floors. (a) Single trap symphonic W.C. Suite. (i) White. (HSR 30.5 (a) (i)

Extra over item no. 30.1 to 30.4 and 30.6 for providing and fixing 15 Litres Capacity Vitreous China High Level Cistern Complete with internal brass fittings instead of 12.5 Litres capacity high level C.I. eastern complete (as approved by the Engineer-in-charge). (i) White. (HSR 30.8 (i)

Extra over item nos. 30.3 to 30.6 for providing and fixing best Indian make plastic Hygenic seat with lid complete instead of hollow Black or white plaster seat and lid. (i) White plastic seat (Solid). (HSR 30.13 (i)

Extra for providing and fixing 32mm dia G.I./C.P flush pipe complete with accessories instead of 32/mm dia galvanized telescopic flush pipe with clips (as required by the Engineer-in-charge). (a) 32mm dia G.I. flush pipe. (HSR 30.15 (a)

Providing and fixing in position Indian make (Ordinary) Lavatory Suites Consisting of Lavatory in Vitreous China Ware size as given Below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary; R.S or C.I Brackets for building into wall including Painting; 32mm C.P Brass Waster with C.P brass chain and rubber plug; 15mm C.P Brass Screw down pillar tap with Jamnuts or couplings best design (as approved by the Engineer- In-charge). All fittings best Indian make and to the approval of the Engineer-in-charge. All brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fittings etc. (a) White. (iv) Size 550 mm x 400 mm with one no. Tap. (HSR 30.41 (a) (iv)

Providing and fixing in position best Indian make Pedestal fittings of vitreous chinaware complete (as required by the Engineer-in-charge). (i) White. (HSR 30.44 (i)

Providing and fixing in position best Indian make Vitreous Chinaware Sinks with complete fittings as fully described in item no. 30.51 above. (a) White. (i) Size 600mm x 450mm x 250mm. (HSR 30.52 (a) (i)

Providing and fixing in position best Indian make Shower with 15 or 20 I/d inlet. (d) C.P brass telephonic shower. (HSR 30.66 (d)

Providing and fixing in position best Indian make Paper Holders fixed into wall with C.P Brass screws complete in all respects including cutting and making good the walls etc. (a) C.P Brass. (HSR 30.67 (a)

Providing and fixing in position best Indian make towel rails fixed in with rawlslugs embedded in walls with C.P brass screws complete in all respect including cutting and making good the walls etc. (a) 25mm dia C.P brass adjustable. (i) 750mm long. (HSR 30.68 (a) (i)

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P brass screws and complete in all respects including cutting and making good the wells etcs. (a) C.P Brass. (i) Soap dish 160mm. (HSR 30.70 (a) (i)

Providing and fixing in position best Indian make bevelled edge 5.5mm thick Mirror mounted on Asbestos sheet ground fixed in position by means of 4 Nos. chormium plated brass screws and washers over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) complete including cutting and making good the walls etc. (a) Indian make. (i) 600mm x 450mm. (HSR 30.71 (a) (i)

Providing and fixing in position 15mm i/d C.P brass bib Cocks of best quality (as required by the Engineer-in-charge). (HSR 30.75)

(a) Bib cock long body.

(c) Bib cock.

Providing and fixing in position C.P brass stop cocks (as Approved by the Engineer-in-charge). (a) 15mm stop cock. (HSR 30.76 (a)

(i) Stop cock male and female end.

(ii) Concealed stop cock with flange.

Providing and fixing in position best Indian make flexible tube connection. (b) C.P Brass. (iii) 15mm x 450mm. (HSR 30.82 (b) (iii)

Providing and fixing in positon best Indian make (to the approval of the Engineer-in- Charge) storage type automatic electric water heater, pressure/non pressure type. Thermostat cally controlled, suitable for operation on 230 volts, 50 cycles single phase vertical wallmounting fitted with with- drawable and adjustable type a.c. thermostat. Thermostat knob to be readily. Accessable through the opening of suitable cover for adjustement of temperature in the insalled position of heater and the thermostat should be withdrawn without having to drain the water, electric heating element should made out of copper tube (heating element should be easily removed and replaced in the installed position of heater) a neon indicator 1amp. inner contained made out of coppertinned both from inside and outside outer container made out of mild steel sheet finished in gleaming white stove enamel paint insulated between the inner and outer with fibre glass wool with 1 metre length of suitable capacity 3 core flexible cord with plug and non return valve plastic/lead connections or pressure release valve (where required). Complete including fixing and testing for a week (as required by the Engineer-in-charge) VERTICAL WATER HEATER. (j) 140 litres capacity (HSR 30.117 (j)

Providing and fixing HDPE Water Storage Tanks of Sintex, Diplast, O.K. supreme make with covers/ lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respect to the satisfaction of Engineer-in-Charge. (except civil work). (e) 1000 Ltr. Capacity. (HSR 30.119 (e)

Providing and fixing SFRC MANHOLE COVERS AND FRAMES MARKED WITH IS: 12592 including setting the same to correct lines and levels in 1:2 cement sand mortar over manhole inlcuding carriage loading, unloading, stacking handing re-handling etc. complete in all respect to the satisfaction of Engineer-in-charge. (a) Type: Extra havy duty set (EHD-35) 560mm clear opening. (HSR 29.94 (a)

Providing Salt Glazed Stone, ware pipes grade "A" in standard length of 600mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in HSR item no. 29.38, 29.39, 29.40 including the cost of jointing materials as well as carriage, loading, unloading stacking, handing, re-handling etc. complete in all respect to the satisfaction of Engineer-in-Charge. (b) 150mm i/d. (HSR 29.95 (b)

Constructing brick masonry inspection chamber sizes as given below upto 0.60 meters average depth in cement mortar 1:5 lime concrete with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement RCC 1:2:4 slab 100mm thick/C.C. topping 50mm thick with 455mm x 455mm / 455mm x 610mm inside light duty C.I inspection chamber cover and frame weight as per I.S.I specification painted with 3 coats of black bitumastic superior paint complete as per standard design. (a) Size 450mm x 450mm inside (with 455mm x 455mm cover and frame light duty single seal weighing 40 kg with C.C. topping). (HSR 29.84 (a)