Special repair to IFA Bldg under GE (West) Jalandhar Cantt

Amount

Dismantling of brick tiles single layer as in roof covering complete all as specified

Demolition of mud in roofs any thickness including plastering and leeping(whether full thickness removed or only a part thereof) all as specified.

Material and labour for 3mm thick superior Atactic poly propylene modified polymeric membrane waterproofing treatment of weight not less than 3.6 Kg per sqm with properties of high penetration and the centre core consisting of 90 micron high Molecular-High Density polyethylene (HMHDPE) film consisting of five layers. The superior multi polyplus is to be laid after preparing the surfaces by cleaning thoroughly to achieve a smooth surface over and including a coat of bitumen primer @ 0.30 Litre per sqm over a coat of hot applied Blown Bitumen of grade 85/25 @ 1.2 kg per sqm. The overlaps between super multi polyplus are minimum 10cm seam in width/lengthwise complete all as specified and all as per manufacturer’s directions.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M & L for 10mm thick rendering on concrete surfaces finished even and smooth without using extra cement in cement mortar 1:4 as in roof/sunken floors and using WPC 3% by wt of cement. Note : WPC shall be measured and paid separately under respective item.

M & L brushing neat cement slurry with 3kg of cement per sqm complete all as specified

M & L PCC Padding with cement concrete type B-I (1:2:4) 20mm graded aggregate to bring top surface of slab in slope complete all as specified

M & L 40 mm thick. Brick tiles laid on bedding layer of CM 1;3 15mm thick and joints grouted flush in cement mortar 1:3mixed with 5% of crude oil by weight of cement over APP membrane complete all as specified

All as per description of Srl item No 8 here-in-before but except tiles

M & L flush pointing in CM 1:3 to brick tiles laid flat in roof or paving incuding raking out joints complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exc 15cm thick as in floors ( below or above ground level) all as specified

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing) and disposal of rubbish outside MD land complete all as specified

M&L for 25mm thick PCC 1:2:4 type B0(using 12.5 mm graded aggregate) as in floor finishing complete etc complete all as specified and as directed

Taking down cement plaster of any description any thickness /dado/Skirting/ including raking out joints hacking for key scrubbing down with water complete all as specified.

M&L for 15 mm thick rendering in cement mortar 1:6 on brick or concrete surface finished even and smooth without using extra cement all as specified

All as per item No. 15 above but in CM (1:4) complete all as specified and directed.

M&L Plastering 5 mm thick in cement mortar (1:3) finished even and smooth without using extra cement as on ceiling complete all as specified

M & L for vitrified ceramic tiles light shade 10 mm thick (Square/rectangular) polished area of each tiles not exceeding 0.36 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified.

All as per description of Srl item No 18 here-in-before but in skirting over and including 10mm thick rendering as backing coat of CM 1:4 complete all as specified.

M&L for non skid ceramic, coloured, joint free, tiles 7 to 8 mm thick (square/rectangular) size of tiles not less than 300mmx300mm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match with colour of the tiles over and including screed bed of 15mm thick cement mortar (1:4) complete all as specified and as directed.

All as per description of Srl item No 20 above but in skirting over and including 10mm thick rendering as backing coat of CM 1:4 complete all as specified.

M&L for coloured glazed tiles of size 450x300x 7 mm thick fixed with neat cement slurry in vertical surface to wall pointing in white/coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified.

M&L for preparing new plastered surfaces of walls and applying two coats of oil bound distemper with chalk whitening on plastered surface preparatory to distempering complete all as specified.

M & L for Preparation of new plastered surfaces or unplastered surfaces of walls/ceilings and applying three coats of white wash all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment from plastered surfaces of walls and applying two coats of oil emulsion distemper (white / tinted) over 1 mm thick wall care putty complete all as specified.

M & L for preparation of old plastered surfaces or unplastered surfaces of walls and applying two coats of white wash all as specified and directed by Engr-in-Charge.

All as per above item No 26 herein before but single coat of white wash but on ceiling surfaces complete all as specified.

M&L for preparing new plastered or unplastered wall surfaces and applied two coats of cement base paint over one priming coat all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatments on wall surfaces and applied two coats of cement base paint over one coat of primer all as specified and directed by Engr -in-charge.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

M & L for reinforced cement concrete 1:1.5:3 type A-1 using 20 mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies , canopies , deck slabs and in shelves and the like complete all as specified and directed.

M & L for mild steel high yield strength TMT bars 8 mm dia cut to length bent to shape require including, cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, shelves , landing and similar work not exceeding 200 mm thick (horzontal or sloping) and to edges of concrete complete all as specified and directed

M&L for 50mm PCC 1:3:6 type C1 using 20mm graded aggregate as in plinth protection and path finishing the surfaces even and smooth without using extra cement all as specified

Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excludding precast concrete articles all as specified.

M&L for brick work with sub class 'B' old size bricks straight or curved on plan to any radius with old size brick thick walls/manhole built in cement mortar 1:6all as specified.

All as per item No 36 above but using old bricks complete all as specified.

M&L for half brick thick wall using with sub class 'B' old size bricks straight or curved on plan to any radius with old size brick thick walls built in cement mortar 1:4all as specified.

Taking down chowkhats or frame with shutter w/o taking off shutter from the frame area not exc 1.5 Sqm each all as specified.

All as per Srl item No 39 above but area exc 1.5 Sqm and not exc 4 Sqm each. all as specified.

M & L for mild steel conforming to Fe 290, Gde E-165 framed work as in door frames, chowkhats including necessary cutting, welding, bending, drilling etc., complete all as specified and directed.

S&F 30 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F glazed and skeleton shutters 35mm thick open rebated and prepared to receive glass,gauge etc (without sash bars) edging of framing plain, chamfered or rounded with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Pt-I, Section 8, Clause 8.24(a).

Material and labour for Steel windows 1.25 mm thick Box type (primer coated) ERW hollow ‘P’ section of size 60mmx25mm single rebated comprises of glazed skeleton shutter EWR Sec 50mmx20mm and 1mm thick and two openable leaf consisting two Nos sash bar of ‘T’ section 20mm x 3mm complete welded to frame with one vertical mullion of EWR box type ‘T’ section of size 60mmx25mm and 1.25mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B1 using 20mm graded stone aggregate. (Four Nos for each window) including following fittings welded to framed shutter :- (a) Holdfasts 150mm long 12mmx3mm made to shape per window -04 Nos, (b) Handle of Z Sec 20mmx25mm, 100mm long per leaf-01 No, (c) MS tower bolt 150mm long per leaf -02 Nos, (d) ‘Z’ sec 20mm x 25mm, 100mm long stopper per leaf -01 No, (e) Cleat 55 mm long of hollow square 15mmx20mmx63mm welded to hinges per leaf -01 No, (f) MS pintal hinges of size 75mmx12mm per leaf -02 Nos, (g) Fabrication and fixing arrangement shall be all as per drawing No CEJZ/TD-1019/08 & 1020/08 Sh 1/3 to 3/3. (Note: Wire gauge shall be measured and paid for separately).

All as per Srl item No 44 above but as in glazed windows Complete all as specified. Note for item No 44 & 45:- (i) Fabrication and fixing arrangement as per drawing No CEJZ/TD-1019 and 1020. sh 1/3 to 3/3. Drg are not being uploaded and same can be seen in this HQ on any working day. (ii) ..Grill/Wire Gauge/Glass/Painting shall be measured and paid for separately.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified.

M & L steel ventilator fixed type all as specified and directed

M&L for sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane.complete all as specified.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks or wire staples complete all as specified.

M&L for preparation of old painted surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and painting one coat of synthetic enamel paint in tint as directed all as specified.

M & L for preparation of new steel surface of any description over 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

M & L for preparation of new wood and wood based surfaces of any description over 10CM width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S&F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinfoced with MS square tube, suppling and fixing in opening as per specification and as per manufacturer's instructions.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & as per manufacturer's instructions.

M&L mild steel work as in holdfasts, knee piece and similar small article complete all as specified.conforming to Fe-290 Gde-E-165 complete all as specified.

S&F 300mm long Aluminum alloy, anodized sliding door bolt with hasp & staple (bolt type) fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminum alloy and fixed.complete all as specified.

Supply & Fixing 100mm size butt hinges extruded aluminum alloy with galvanised mild steel hinge plate complete all as specified.

S&F Aluminum anodized barrel tower bolt of extruded section of size 150mm complete all as specified.

S&F extruded Aluminum alloy handle fabricated of size 150mm complete all as specified.

M&L for PCC (1:2:4) type B-1(using 20 mm graded stone aggregate) as in roof kerbs, mud stops, coping, coved fillets of radius 75 mm provided at junction of parapet walls etc edges of concrete rounded or chamfered complete all as specified and directed .

Taking up of or down steel tubing and connections 15mm bore/20 mm bore and connections, including cleaning for refixing or removing to store yard complete all as specified and directed,

S&F 15mm bore galvanized iron tubes medium grade with all fitting and fixed complete to walls, ceiling or laid in floor complete all as specified.

All as per description of item No 62 above but for 20mm bore tube complete all as specified.

Refixing only old steel tubing in new or old position (wall/ceiling/floors etc) including new fittings 15 mm bore pipe complete all as specified directed

Refixing only old steel tubing in new or old position (wall/ceiling/floors etc) including new fittings 20 mm bore pipe complete all as specified directed

Cutting chases to brick work, pinning in making good for concealed water tubing and making good ,cutting not exc 10cm girth complete all as specified.

S&F in repair Stop valve,20 mm cast copper alloy with long shank &cup with capstan heads, screwed down, high pressure, with crutch or butterfly handle screwed for 20mm bore iron fixed complete all as specified

S&F in repair 15mm angular stop valves, fancy type chromium plated, with long shank and cup(concealed) screwed down, high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed complete all as specified.

S&F in repair 15mm stop valves/Angle cock , fancy type chromium plated, screwed down, high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed complete all as specified .

S&F in repair Bib tap fancy type cast copper alloy suitable for 15mm bore iron pipe with long body fancy type complete all as specified .

S&F in repairs vitreous China wash down water closet pan (pedestal pattern) white including bolts, flush pipe of polyethylene of low or high density or PVC 32 mm dia anti syphonage pipe with chromium plated etc complete all as specified.

Supply and fixing plastic water closet seat cover closed patern with flat bottom and cover and mild steel chromium plated or aluminised hinging devices complete all as specified.

S & F brass chromium plated jet for pedestal pattern water closet including PVC flexible pipe alongwith complete necessary fittings all as specified and directed by the Engr- in- Charge.

S&F in repairs PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle with flush pipe 10 Ltr capacity complete all as specified.

M & L for PVC connection fiber, reinforced 450 mm long with brass check nut and PVC washers at both ends complete

S&F Hot and cold mixer fancy type single or double legged cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends iron pipe suitable for 15mm bore pipe fixed to wash hand basin complete all as specified

S&F Vitreous china wash hand basin, white flat, size 550 x400 mm incl brackets 32 mm waste coupling and waste pipe all as specified and directed by Engineer - in - Charge.

Disconnecting existing water tanks of any capacity and description and removing to store complete all as specified and directed.

S&F 1000 ltr rotational moulded polythylene water storage tank double layer (Cylindrical vertical with closed top) hosted and fixed in position complete all as specified.ISI marked

S&F 20mm ball valve brass high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed

S&F 20mm Gun metal globe or gate valves, with iron wheel head screwed both ends for iron pipe and fixed.

S & F for toilet paper holder vitreous china complete all as specified and directed

Supply and fixing acryclic shelf 450mm long and 100mm wide of sample as approved by Engineer-in-charge/ GE fixed with brackets including CP brass screws and wooden plastic cleats of approved quality complete all as specified and as directed.

Supply and fixing corner set of three acryclic shelf 300x300mm of sample as approved by Engineer-in-charge/ GE fixed with brackets including CP brass screws and wooden plastic cleats of approved quality complete all as specified and as directed.

Supply and fixing grating chromium plated 125mm dia with centre hole fixed in cement mortar 1:3 complete all as specified.

S&F 20 mm dia chromium plated towel rail 600 mm long of approved make complete all as specified and directed .

Dismantling of 100mm/75MM/50 MM dia PVC or reinforced concrete drain pipes, jointed in cement motar and taking out of trenches or taking out of walls, if required.

S & F 110 mm bore PVC (SWR) pipe of pressure rating 6kgf/cm2 single socketed in any length with rubber ring joints jointing with adhesive fixed in repair to wall/laid in trenches complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends in any radius complete all as specified and directed.

S&F PVC (SWR) junction single (single tee) equal or unequal, dia of pipe 110 mm complete all as specified and directed.

S & F 75 mm bore PVC (SWR) pipe of pressure rating 4kgf/cm2 single socketed in any length with rubber ring joints jointing with adhesive fixed in repair to wall/laid in trenches complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends in any radius complete all as specified and directed.

S&F PVC (SWR) junction single (single tee) equal or unequal, dia of pipe 75 mm complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap with grating including joining to waste pipe fixed in solvent cement incl taking down damaged floor trap in any position complete all as specified and directed.

S&F 110mm dia PVC (SWR) floor trap with grating including joining to waste pipe fixed in solvent cement incl taking down damaged floor trap in any position complete all as specified and directed.

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and as directed.

Demolition and breaking drain pipe 150mm internal dia of pipe (salt glazed stoneware) set in cement mortar including packing under and haunching against side of pipe complete all as specified.

All as per Srl item No 97 above but 100mm internal dia of pipe complete all as specified.

Supplying, laying, jointing and testing RCC NP-3 pipe 150mm internal dia complete all as specified and as directed laid and jointed with collars in any position complete all as specified.

All as per Srl item No 99 above but 100mm internal dia of pipe

M & L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate for 150 mm Internal dia of pipe complete all as specified and as directed

All as per Srl item No101 above but 100mm internal dia of pipe complete all as specified and as directed

Returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and as directed.

Removing excavated material to a distance n exc 50M and deposited where directed at a level n. exc 1.5M above the starting point complete all as specified and as directed.

Supply only Integral water proofing compound conforming to Is-2645 complete all as specified.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 6mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size including taking down complete all as specified and as directed.

S & F Stack clamps made out of 25 mm by 3 mm flat iron and 8 mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof 100 mm bore of pipe.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in any type of soil complete all as specified and directed.

M&L, 100mm thick, PCC 1:4:8 type D2 using 40mm graded stone agg as in filling and mass concrete, Sub base/flooring complete all as specified and directed.

M&L, sand cushioing to under concrete interlocking paver block including watering & consolidation complete all as specified

M&L for 80 mm thick machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60mm thickness, M-40 grade with grey cement & pigment.complete all as specified and directed.

M & L for septic tank for 30 users complete all as specified and as shown on drgs

M & L for Soakage well of size 3m dia x 4.5m effective depth complete all as specified and as shown on drgs

Taking down carefully existing point wiring of any type (i.e. wooden surface consuit casing capping or conceated conduit) complete for light or fan or socket or power etc on wooden batten or in conduit including fittings and accessories like switches, sockets, lights fitting, regulator, wooden board and making good disturbed portion to match with existing complete all as specified and directed.

Material & labour for concealed point wiring complete with single core 1.5 Sqmm (nominal area) PVC insulated and unsheathed cable 1100 volts multistranded, copper conductor cable (FRLS) drawn through and including PVC concealed conduit not less than 20mm dia bore medium grade (ISI marked) and accessories like bends, tees, junction boxes etc, fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire including sunken type pressed steel terminal boxes and plastic laminated white/ coloured top sheet cover 3.0 mm thick , for One light point / fan point / call bell point controlled by one way switch complete all as specified and directed.

All as per srl item No 117 here-in-before but for 5 Amp on on independent board complete all as specified and as directed

All as per srl item No 117 here-in-before but 5 Amp on same board complete all as specified and as directed

All as per description of srl item No 117 above but with 2.5 Sqmm cable for 15 amps switch socket combination outlet on independent board complete all as specified and directed

All as per description of srl item No 117 above but with 4 Sqmm cable for AC on independent board complete all as specified and directed

Supply and fix switch piano flush type, 5 Amps, 240V AC, single pole, one way complete all as specified and directed

Supply and fix socket out let 5 Amp 5 pin flush type complete all as specified.

Supply and fix switch socket combination out let universal type 6 pin 5/15 Amp multi pin complete all as specified.

Supply and fix MCB SPN 6 to 32 Amp, 240 volts,10 KA, C-curve complete all as specified and directed.

Taking down U/S submain wiring of any size and make complete all as specified and directed.

M&L for sub main wiring with two runs of single core PVC insulated, unsheathed copper condutor, multi stranded cable of size 6.00 Sqmm 1100 volts grade drawn through PVC concealed conduit of size 25 mm (ISI marked) including PVC accessories complete incl cutting and chasing and making good etc including one run of 6.00 Sqmm single core copper conductor multi-stranded PVC insulated, unsheathed cable as earth wire continuity conductor complete all as specified and directed by Engr-In-Charge Note: Two run of 6.00 Sqmm cable and one run of 6.00 earth wire & 25 mm PVC conduit shall be measured as one unit length.

S & F for batton holder insulated body with 5 Watt LED bulb all as specified and directed

S & F for stepped socketed type electronic fan regulator flush type all as specified and directed

Supply & fix LED light fitting 22W retrofit including LED lamp with 2100 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixtures box type with retrofit LED rod 22 watt and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed. Make :Havells cat part No. LUMLINEPLUSBS22WLED865SPCSS or equivalent as mentioned in appendix 'B'

Supply & fixing in replacement LED street light fitting 20W including LED lamp pressure die cast aluminium IP-66 with surge protection device of 10 KV, IK7 LED (SEOUL) 6500 and connecting including all fittings as specified and directed by Engr-in-Charge Make: Havells Cat Part No LHETBXU7PA6W048 HSN code or equivalent as in Appx 'B'

S & F and ceilling rose surface type bakelite 65x50mm three terminal all as specified and directed

S & F in repair 34watt 2x2 LED PLUTO NEO ceiling fitting light fitting atra modern designed LED luminaire which provides soft-light and glare free symetrical illumination suitable for armstrong/Grid Celing including Bracket nuts bolts washer as required for fixing complete all as specified and directed. Make : Cat Part No PLUTONE02X2PLR34WLED840S or equivalent as in Appx 'B'

Taking down main switch board of any size and making good distrub surface of wall/floor complete all as specified and directed

Supply and fix sheet metal enclosures for DB's with 200 Amp rated bus bar double door class IP-43 epoxy coated inside and outside 4 way TPN 440 volts with incoming/outgoing connection through proper size of lugs complete all as specified and directed

Supply and fix isolator TPN 63 Amps 415V complete all as specified and directed.

Supply and fix DB SPN 8 way double door for MCB 240 Volts with 200 Amps rated bus bar complete all as specified and directed.

Supply and fix isolator B Curve SPN upto 40 Amps 240 V complete all as specified and directed.

M & L for MCB B Curve SP 6 to 32 Amps complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of theplate not less 1.5 mtr deep below normal ground level connected to GI earth wire 4mm dia connected to earth plate earth plate by means of nut, bolts, check nut & washer of galvanized iron or of steel, GI earth wire will be protected by 15 mm dia GI pipe 'light grade', watering pipe 20 mm dia GI 'light grade', GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate upto thickness of 150 mm, filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to O/H continuous earth wire on pole, testing the earthing after completion complete all as specified and directed. Note :- (I) Earth pit shall be constructed 50cm from the side of excavation to avoid sinking of pit (II) PCC chamber shall be (1:3:6) using 20mm graded stone aggregate and 50mm thick RCC (1:2:4) type B-1 cover slab reinforced with 8mm dia TMT steel bars @ 100mm c/c both ways complete all as specified and directed.

Supply and lay GI tubing light , grade 40mm bore with all necessary fittings laid in trenches under road crossing in floors complete all as specified and directed.

Taking down XLPE insulated armoured heavy duty electric cable with aluminium conductor complete all as specified and directed.

Supply and laying XLPE insulated, armoured heaby duty electric cable with aluminium conductor 1100 volts grade cross sectional area 4 core 50 sqmm on floor/wall including lugs & fitting for fixingcomplete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc and getting out in soft/loose soil complete all as specified and directed.

Returning filling in layers including leveling watering and well ramming in layers not exc. 25cm thick complete all as specified and directed.

Supply and spread river sand in trenches as cable cushioning 8 cm below the cables and 15cm aboe the cable all as specified and directed

Removing excavated material n not exc. 50m and depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and directed.

Supply and lay burnt bricks sub Class 'B' standard size laid across the cable in trenches as protection to the cable all as specified and directed

M/s Nirmal Singh and Co.

SARASWATI CONSTRUCTION CO

NATIONAL BUILDERS