SPL REP TO BLDG NO T 101 OR SINGLE LIVING ACCN) AT 2 TECH TRG BN 3 EME CENTRE 03 SRW PROVN OF RATION STORE CUM RATION STAND AT 194 FWC 01 REV AND PROVN OF 30 GEYSER AT OR LINES A COY B COY C COY REV 03 AT BAIRAGARH UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Dismantling of asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings, including ridge complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI Based corrugated steel sheeting 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, chajjas, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

Dismantling of wall and celing hard boards/AC sheets and plywood in any thickness & any position including cover fillets complete all as specified and directed

M&L for galvanised cold rolled steel section frame work size 600x600mm grid size using 24 x 38 x 0.50mm (composite thickness) tee (bottom pre-coated) and 24 x 24 x 0.50mm (composite thickness) wall angle galvanised cold rolled steel section including suspenders as per (Gabsec) manufacturs instruction as in ceiling all as specified and direcetd (Make : GABSON (Gabsec) or equivalent as per list of make Appx 'C' as approved by the GE)

M &L for Asbestos free calcium silicate board of size 600 x 600 x 6mm thick fixed to steel frame work as in ceiling, including applying two coats of oil bound distemper all as specified and directed .

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over and including 15mm thick screed bed in CM 1:4 etc set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over as in skirting and including 10 mm thick rendering in CM 1:3 set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified.

M&L for granite (any type) 20 mm thick work(table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter, shelves and like in cement mortar )1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M/L for non skid ceramic coloured tiles 7mm to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 Sqm, but not exceeding 0.18 Sqm, in floors over and including 15mm thick screed in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified & directed

M&L for coloured glazed wall tiles in vertical surface 300 x450mm x7mm thick, set and jointed over and including 10 mm thick rendering even and rough in CM 1:3 for backing of tiles, set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles complete all as specified and directed.

Demolition of cement concrete in ground floor, (unreinforced) paving nexc 15 cm thick (below or above GL) complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation, filling, subbase and mass concrete complete all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in foundations, sub base and mass concrete and like complete all as specified and directed.

Taking down chowkhats or frame nexc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed

Taking down chowkhats or frame exc 1.5 sqm but nexc 4.00 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

S&F Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, with & including filing of cement concrete typ B-0, 1:2:4 using 12.5mm graded stone aggregates inside frames complete all as specified and directed.

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, with & including filing of cement concrete typ B-0, 1:2:4 using 12.5mm graded stone aggregates inside frames complete all as specified and directed.

S&F for 40mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

S&F in Window ECO 4000, of double rebate openable/fixed window made of galvanised steel colour coated/powder coated (base steel as per IS 513 Of 'D' quality, galvanised as per IS 277 with zinc of 120 gms/sqm) with total thickness of coating 0.58 microns thick and back coated with alkyd backer 5-7 micron thick or powder coated with pure polyster powder up to 50-60 micron thick. Outer frame section 72 x 55 mm , center mullion section 72 x 50 mm, shutter section 47 x 20 mm, fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consist rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the section cut to length mitre joined with corner bracket, center millions fixed with mullions cap, stay, handle, latch, 2 nos of heavy duty stainless steel pivot hinges per shutter and paneled with 5 mm thick plain float glass and S. S. mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propyelene Diamine Monomer) gaskets including fixing windows in the Concrete /Masonry wall by means of self expanding screw, including 10 mm square bars welded to 6 x 12 mm flat at a distance 150mm C/C (Pitch) etc, complete all as specified and directed.

Providing and fixing fixed louvers fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 grams/Sqm) with thickness of 0.58mm coated sections to be primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick, section for external frame 33 x 58 mm, glass holding flanges made of polypropylene, sections are to be cut to length, mitre joined with corner bracket. The above frames should be fixed to the concrete/masonry walls by means of self expanding screws, complete all as specified and directed.

S&F Solid PVC door frame of size 50 mmx 47mm made out of 5 mm plain colour PVC sheet reiforced with MS square tube and fixing in opening as per manufacturer instruction complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 200 mm Aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed

S&F 150 mm Aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed

S&F 100 mm mild steel butt hinges medium weight, cold rolled complete all as specified and directed

S&F 100 mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type complete all as specified and directed

S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed

M&L for factory made second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperure 1.18 mm and fixed with tinned tacks, or galvanised wire staples fixed complete all as specified and directed..

M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any description and in any position not other wise specifically provided for complete all as specified and directed.

M&L for Mild steel TMT Bar 6mm to 8mm dia and over cut to length, bent to shape to required, including cranking, bending spirally for hoping for columns, hooking ends and binding with and including mild seel wire (anneled ) not less than 0.9mm dia or securing with clips quality confirming all as specifed and directed.

M&L for Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed. (Note:-Reinforcement shall be measured separately).

Demolition of brick work, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces, including wall tiling if any, racking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for brick work with fly ash bricks (modular size bricks), straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for brick work with fly ash bricks (modular size bricks) straight or curved on plan any radius in half brick thick walls, built in CM 1:4 all as specified and directed.

M&L15mm thick rendering in CM 1:6 on brick/concrete surfaces including finishing the surfaces even and smooth (without using extra cement) complete all as specified and directed.

M&L 15mm thick rendering in CM 1:4 on brick/concrete surfaces including finishing the surfaces even and smooth (without using extra cement) complete all as specified and directed

Preparing new plastered or unplastered surfaces of wall and M&L for applying two coats of exterior acrylic emulsion paint, white or tinted over and including a coat of exterior wall primer on plastered surfaces complete all as specified and directed. [Make :Shalimar(Saktiman) / Asian(ACE) / Burger(wall masta)]

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of cement based putty complete all as specified and as directed. Note: Putty shall be measured and paid for seperately under respective item

M&L for preparation of existing treatment by complete removal of existing treatment of any layers and including filling of cracks, holes by suitable material like cement based putty, and applying two coats of exterior water base emulsion paint over a coat of primer on walls all as specified and directed. [Make :Shalimar(Saktiman) / Asian(ACE) / Burger(wall masta)]

M&L for complete removal of existing treatment from walls and applying two coats of oil bound distemper over a coat of cement based putty complete all as specified and as directed. Note: Putty shall be measured and paid for seperately under respective item.

M&L for applying one coat of white wall care putty 3mm thk on walls complete all as specified and directed.

S&F steel work as in tubular (round/square/rectangular) shape of pipes as approved by Engr-In-Charge) trusses of semi circle shape including post special shaped washers etc complete incl necessary nut bolts wind ties and gusset plates etc using ERW or induction butt welded tubes conformining to IS 1161-1998 grade St-240 complete all as specified and directed.

M&L MS work, angle iron, flat iron, MS plates as in brackets, cleats, fastners, wind ties, supports, base for posts etc with riveted, bolted or welded attachment complete of Fe-410-W (Gde-E-250) quality-A all as specified and directed.

S&F in repairs 25mm dia drapery rod, mild steel, chromium plated 1mm thick of standard quality with fixing brackets, stops rollers fancy type etc complete all as specified and directed..

S&F in repairs PVC low level flushing cistern 10 litres capacity, ISI marked, white, with all fitting and fixtures including brackets, PVC connection of 450mm long and 32 mm bore PVC flush pipe, complete all as specified and directed. [MAKE:- SOMANY (Cat No.121002), Prayag (Cat No.501 Smart flush cistern) or equivalent in PARRYWARE-SLIMLINE/CERA/ make as per Appx 'C' (list of make) as approved by GE]

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (angle type) screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed. [MAKE:- Prayag (Cat No.8310) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]

S&F in repairs Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8306) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8318) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]

S&F in repairs brass chromium plated shower rose 125 mm in size with or without swivel joints any size incl fixing to steel pipe or union, complete all as specified and directed.

S&F in repairs Vitreous china wash basin, white, oval type, size 520 x 450mm including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed. MAKE:- SOMANY (Cat No.110501) or equivalent in HINDWARE/ CERA/PARRYWARE make as per Appx 'C' (list of make) as approved by GE]

S&F in repairs 15 mm pillar cock swan neck, single lever, chromium plated, screwed down high pressure, with or without lettered Hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. Make Prayag (Cat No-9014) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]

S&F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

Taking up or down 20 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 20 mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Taking up or down 15 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15 mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F in repairs Vitreous china squatting pan ‘Orissa’ pattern, ISI marked, size 580 x 440 mm, white with integral foot rests including provision of cement concrete bedding & ‘P’ or ‘S’ trap complete all as specified and directed.

S&F in repairs Vitreous china urinal half stall ISI marked, white, with & including chromium plated waste coupling including connections to flush pipe and outgoing pipes complete all as specified and directed. [MAKE:-SOMANY smart / HINDWARE (Cat No.60002 starwhite) or equivalent in CERA/PARRYWARE/ Prayag as approved by GE.]

S&F in repair 100mm dia CP grating complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Returning filling in with excavated soil of any type including spreading,leveling, watering and well ramming in layers n exc 25 cm thick complete all as specified and directed.

Removing excavated material exc 250 m and not exc 500 mtr and depositing where directed complete all as specified and directed by Engr-In-Charge.

Demolition and breaking up of 150 mm dia of drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

M&L for 150 mm bore salt glazed stone ware drain pipes laid in trenches and jointed complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2, concrete bed to drain pipes 100 mm dia including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware,AC or Reinfoced concrete), 110mm/75 mm dia, set in cement mortar, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed in walls/ laid in trenches/floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed in walls / laid in trenches/floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F PVC (SWR) bends any radius 110 mm dia complete all as specified and directed.

S&F PVC (SWR) bends any radius 75 mm dia complete all as specified and directed.

S&F in repairs 75mm dia PVC (SWR) floor/Nahani trap with grating including jointing with solvent cement complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

Dismantling unframed work timber scantlings 40 sq. cm and over in section, in any position, complete all as specified and directed.

S&F rolled mild steel work as in rafter, purlins, trusses and like (beam, tee, angle, channel or flat sections ( Fe 410-W(Gde E-250 quality) complete all as specified and directed by Engr-In-Charge.

M&L for preparing new or untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for Hardcore of Broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Factory made, machine pressed, M-35 grade concrete interlocking paver blocks (glossy /reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 60 mm thickness with & including 50 mm thick sand cushion and joints filled with sand complete all as specified and directed.

S&F 4mm GI wire for mosquito net hanging in room including wall hanging spring complete all as specified and as directed.

M&L for Reinforced cement concrete design mix M-25 in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in columns, pillars, posts & struts complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in slabs supported on walls, beams & columns complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in chajja, etc, complete all as specified and directed.

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for rough finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for rough finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for rough finished surfaces of concrete complete all as specified and directed

Use & waste of Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for rough finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides & soffits of chajja, etc for rough finished flat surfaces of concrete complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for treating the top surface of filled earth with anti termite solution, at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and directed.

M&L for treating the soil under plinth protection with anti termite solution, at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and directed.

M&L for treating the soil external perimetre of building with anti termite solution, at the rate of 2.25 litres of emulsion per running metre of perimetre wall, complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for 75mm thick Plain Cement Concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for rendering 20mm thick in two coats of 10mm thick each on faces of brick work or concrete surfaces; first coat (rendering coat) in cement mortar 1:6 and second coat (finishing coat) in cement mortar 1:4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished fair and even complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1: 4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick rendering on fair faces of brick or concrete surface in CM 1:3 as in ceiling finishing the surfaces fair & even without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement paint white or tinted complete all as specified and directed.

S&F Framed work of rolled mild steel conforming to Fe 410-W (Gde E-250) quality -A as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; doors etc to be prepared for hanging or sliding with and including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting, running rails & guides) and hanging, fastening & fixing complete all as specified and directed.

S&F factory made Flush shutters 30mm thick, solid core construction, with block board core and plywood face panels, both face covered with decorative face veneers with lipping/frame to match complete all as specified and directed.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle, and peg stay, complete with glazing bars, dovetailed or welded, including mild steel grills/guard bars of approved design or pattern made up of 12 mm square bar, complete all as specified and directed.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle, and peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

M&L for APP based polymeric membrane (plain/gravel finish as per site requirement) reinforced with non woven polyester (weight not less than 150gms/sqm), weight not less than 3 Kg/Sqm and thickness of membrane not less than 3mm having thermal insulation laid on bitumen 85/25 grade at the rate of 1.2 Kg/sqm primer, by forced application, complete all as specified and directed.

M&L for applying 10mm thick plaster in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on cleaned roof surface, complete all as specified and directed. Note : Water proofing compound to be measured and paid separately.

Supply only integral water proofing compound complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

M & L for concealed point wiring for one light/fan point with 1.50 sqmm (nominal area), FRLS PVC insulated, unsheathed, single core multi-stranded copper conductor cable, 1100 volts grade,ISI marked controlled by one one-way switch, drawn through and including concealed medium grade PVC conduit not less than 20 mm dia, ISI marked, with all accessories (PVC Casing and caping of size 25 mm , ISI marked with complete accessories to be used wherever wiring to be run on ceilings and concrete surfaces) including one run of 1.5 sqmm FRLS muti stranded copper conductor (Green colour cable) as earth continuity wire connected to common earth dolly, including sunk sheet steel terminal box GI/MS/ pressed steel terminal box to be conclead in wall, duly painted with two coates of anti corrosive black bituminous paint over a coat of red oxide primer in and out sides and two coated of aluminium paint on internal surface , including laminated hylum sheet cover, ISI marked of Make" Hylem" for mounting of fittings like switches, sockets, fan regulators etc. fixed with galvanised screw and cup washer complete all as specified and directed. Note : Wiring to be done as per arroved colour code in IE rule.Rate includes chase cutting for concealed wiring.

All as per item No. 119.00 here-in-before, but for Fan point controlled by one push button on same board with other switches or independent with cable 1.5 Sqmm. complete all as specified and directed.

All as per item No. 119.00 here-in-before but for 3 pin socket outlet, 5 Amp on the same board with other switches, complete all as specified and directed.

All as per item No. 119.00 here-in-before, but for 3 pin 5 amp switch socket combination on independent board with other switch complete all as specified and directed.

All as per item No. 119.00 here-in-before, but for exhaust fan point controlled by one push button on same board with other switches or independent with cable 1.5 Sqmm. complete all as specified and directed.

All as per item No. 119.00 here-in-before but wiring with 2.5 Sq mm copper cable for 5/15 amp switch socket combination on independent board and provision of 1.5 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.

All as per item No.119.00 here -in- before but wiring with 4.0 Sq mm FRLS mutistranded copper conductor cable for power point with 4.0 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.

S&F Polycarbonate switch piano, flush button, single pole, one way 5 Amp, 240 volts ISI marked, Make: Anchor/ Havells/ L&T (white colur) complete all as specified and directed.

S & F ceiling rose, surface type, 3 terminal, 240 V. (white colur) complete all as specified and directed.

S & F lamp holder (Angle holder) PVC/polycarbonate type cased body with back plate suitable for pendent fittings including LED bulb of 9 Watt. (white colur) complete all as specified and directed.

S&F, stepped type electronic fan regulator, Delux model, 100 watt, 240V, flush type (white colur) complete all as specified and directed.

Supply and fixing Polycarbonate socket outlet 2-in-1, 5 pin 5 Amps, 240 volts, flush type ISI marked (white colur) complete all as specified and directed.

S&F Polycarbonate socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts, ISI marked (white colur) complete all as specified and directed.

S&F Polycarbonate switch piano flush button single pole one way 15 Amp 240 volt ISI marked, (white colur) all as specified and directed.

S&F single pole and neutral enclosure with two pin and earth, plug and socket , suitable for single phase 240 V,complete with one single pole MCB of capacity 20 amps having `C` charactristic, breaking cap 10 KA, including industial plug top, complete all as specified and as directed. Make : Legrand cat part No. 607841 or equivelent in Schinder/ L&T/ make as per list of mke Apppx 'C' as approved by GE.

Taking down old unserviceable sub main wiring of any size and any discription all as directed by Engr-In-Charge.

M&L for sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core PVC insulated FRLS cable 1100V unsheathed with stranded copper conductor of 6.0 sqmm nominal cross section area and drawing into and including rigid non metallic PVC conduit, ISI marked, medium grade, inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples, lock outs, etc. 25mm external diameter and PVC insulated stranded copper conductor of 6.0 sqmm nominal cross section area as earth wire complete all as specified and directed. Note : (i) Wiring to be done as per approved colour code in IE rule. (ii) Two runs of 6.0 sqmm cable, one run of 6.0 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length.

M&L for sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core PVC insulated FRLS cable 1100V unsheathed with stranded copper conductor of 4.0 sqmm nominal cross section area and drawing into and including rigid non metallic PVC conduit, ISI marked, medium grade, inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples, lock outs, etc. 25mm external diameter and PVC insulated stranded copper conductor of 4.0 sqmm nominal cross section area as earth wire complete all as specified and directed. Note : (i) Wiring to be done as per approved colour code in IE rule. (ii) Two runs of 4.0 sqmm cable, one run of 4.0 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length.

Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt, 220 V, AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED light fitting 1x9W/1X10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

Taking down main switches/MCB DBs of any capacity/type including MCBs.

S&F sheet metal enclosure for VT DB TPN, MCCB DB TPN 4 way, double door with MCCB as incomer (Vertical type double door) and suitable for SP/TP DB in outgoing, enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed.

S&F MCCB 3 Pole, 415 V, fixed type, 125 Amps with breaking capacity 30 KA complete all as specified and directed.

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 12 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed.

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed.

S&F MCB SPN 5 to 40 amps 10 KA , 'c'-series including connection with suitable size aluminium / copper lugs complete all as specified and directed.

S&F MCB SP 240 volts 32 Amps, 10 KA breaking capacity, 'c' curve including connection with suitable size aluminium / copper lugs complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor.(BLDC) with hook for hanging ceiling fan including taking down old ceiling fan complete all as specified and directed. MAKE: CROMPTON ENTRUST 50 or equivalent in Bajaj/ Havells/ make as per list of makr Appx "C" as approved by GE. Note : Old ceiling fan shall be deposited to AGE E/M store.

Supply and fix 300 mm exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fixing of temperature resistent PVC connection pipe with brass hexagonal adaptor both sides suitable for HOT/COLD water, 15mm dia, not less than 60 cm long, suitable for incoming and outgoing water connections of geyser with washers etc. complete all as specified and as directed.

Supply and fix electric water heater, storage type steel body and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc Make: Crompton mode No-ASWH1625 or equivalent in Bajaj/Havells/ make as per list of make as approved by GE.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm×6mm thick, buried directly in ground (earth pit not less level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised iron earth wire of 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 5 SSR including earth pit in any soil char coal common salt , 15 mm all around earth plate PCC (1:3:6) type culprit, with 40 x40x6 mm angle iron frame and PCC cover (1:2:4) type B1 , water pipe funnel and GI protection pipe light grade 15mm dia upto panel connecting earth lead to panel all as specified and directed by EIC. Note : Earth continuity conductor including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate.

M&L for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection (8 cm below cable & 15 cm above cable) complete all as specified and directed. [Note:-Compacted/punned thickness shall be measured & paid]

Supplying and laying sub class 'B' bricks (modular) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed

Taking out old u/s cable and Supply and Laying XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 3.5 core x 25 sqmm, laid in trenches/floor or fixed on wall/pole complete all as specified.

S&F 50mm GI tubing light grade with all fittings as required for passing through cables under floors, along the wall or along the pole, etc with suitable size M.S.flat iron clamps incl nut,bolt and washer including taking down old rusted pipe complete all as specified and directed.

M&L for cutting PCC/floor/road and taking out cable and making good, including material as per existing after laying of pipe for cable protection all as specified and directed size of trench not more than 0.30 x 0.30 m complete all as specified and directed.

Taking up or down 25 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 25 mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

M&L for refixing of existing old GI tubing and connections in new or old position including cleaning internally and externally, any grade/make laid in trenches/wall/floor/ceiling including all type of new fittings i.e. sockets, Tee union elbow etc all as specified and directed of size 25 mm bore.

M&L for refixing of existing old GI tubing and connections in new or old position including cleaning internally and externally, any grade/make laid in trenches/wall/floor/ceiling including all type of new fittings i.e. sockets, Tee union elbow etc all as specified and directed of size 20 mm bore.

M&L for refixing of existing old GI tubing and connections in new or old position including cleaning internally and externally, any grade/make laid in trenches/wall/floor/ceiling including all type of new fittings i.e. sockets, Tee union elbow etc of size 15 mm bore complete all as specified and directed

S&F in repairs Gun metal globe or gate valves, conf to IS 778 with iron wheel head, screwed both ends for iron pipe and fixed in existing or new position of size 25mm complete all as specified and directed.

S&F in repairs Gun metal globe or gate valves, conf to IS 778 with iron wheel head, screwed both ends for iron pipe and fixed in existing or new position of size 20mm complete all as specified and directed.

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 8 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed.

S&F MCB TPN 63 Amps 10 KA including connection with suitable size aluminium / copper lugs complete all as specified and directed.

Supply and Laying XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 10x 4 sqmm, ISI marked, laid in trenches/floor or fixed on wall/pole complete all as specified.

Supply and fix Water heater storage type, electric,capacity 40 litres BEE 3 star rated complete all as specified and directed. Make : Jaquar Versa Horizontal or equivalent make as per list of make Appx 'C'

M&L for GI tubing medium grade of 15 mm dia including cutting / chasing into wall for concealed tubing and making goog distuberd suface with cement mortar 1:3 and finishing surface to match with surrounding surface, fixing to existing G I pipe including drilling and tapping, including all necessary fittings such as union,socket, elbow etc, complete all as specified and directed.

M&L for GI tubing medium grade of 20 mm dia including cutting / chasing into wall for concealed tubing and making goog distuberd suface with cement mortar 1:3 and finishing surface to match with surrounding surface, fixing to existing G I pipe including drilling and tapping, including all necessary fittings such as union,socket, elbow etc, complete all as specified and directed.

S&F Gun metal globe or gate valves, conf to IS 778 with iron wheel head, screwed both ends for iron pipe and fixed in existing or new position of size 25mm complete all as specified and directed.

Supply and fixing of temperature resistent PVC connection pipe with brass hexagonal adaptor both sides suitable for HOT/COLD water, 15mm dia, not less than 60 cm long, suitable for incoming and outgoing water connections of Geyser with washers etc. complete all as specified and as directed.

S&F Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8306) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (angle type) screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed. [MAKE:- Prayag (Cat No.8310) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]

Deduct schedule of credit (calculation will be done off line) Rs. 49919.00

RAJPATI CONSTRUCTION

M/S RAKESH TRADERS

PADAMSHRI CONSTRUCTION CO

M/S Shanti Traders

M/s AKG Engineers & Contractors

Samaksh Enterprises

Nakoda Constrcution Company