SENL/SOPD-G/2026-27/01

Construction of embankment with approved materials obtained from borrow pits, with a lift up to 1.50 m transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-1 and 300-2 with a lead up to 1000 m as per Technical Specification Clause 301.5 (i) Private Land

Construction of sub grade and earthen shoulder with approve materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 with lead upto 1000 m as per Technical Specification Clause 303.1(i) Private Land

Construction of granular sub-base by providing well graded materials, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with smooth wheel 80-100Kn static roller to achieve the desired density, complete as per technical specification Clause 401. (ii) For Grading Materials (Gr-II)

Providing, laying, spreading and compacting stone aggregate of specified sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheels roller 80-100 KN in stages to proper grade and camber, applying and brooming stone screening to fill-up the interstices of coarse aggregate, watering & compacting to the required density grading III as per Technical Specification Clause 405. A. Manual Means Using stone screening, Type –B, 11.2mm for Grading –III

Providing and laying of interlocking concrete Block Pavement (ICBP) with cement concrete paving block as per IS15658–2006 of thickness 80mm and 28 days compressive strength not less than 40 n/mm2 over a layer of bedding sand complying thickness 30mm laid over prepared base complying to grading specified in table 1500.6 Block are to be laid wither structure /running /horring bone pattern of bonds as directed by the engineer and are to be laid to proper level and gradenad compacted with appropriate equipment such as plate Vibrator along with specified in table 1500-06 to fill up the gaps between blocks including construction of edges of restraint with M25 cement concrete of width of depth 230 mm each on either edges complete as for draining and technical specification clause 1504 (Including Edge restraint and carriage)

Providing and fixing retro –reflectorised cautionary mandatory and informatory sign as per IRC 67 made of encapsulated leans type reflective sheeting vide Clause 1701.2.3 fixed over aluminum sheeting, 1.5mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450mm x 450mm x 600mm, 600mm below ground level as per approved drawing and technical specification Clause 801 600mm equilateral triangle

Providing and fixing retro –reflectorised cautionary mandatory and informatory sign as per IRC 67 made of encapsulated leans type reflective sheeting vide Clause 1701.2.3 fixed over aluminum sheeting, 1.5mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450mm x 450mm x 600mm, 600mm below ground level as per approved drawing and technical specification Clause 801 600mm Circular

Providing and fixing retro –reflectorised cautionary mandatory and informatory sign as per IRC 67 made of encapsulated leans type reflective sheeting vide Clause 1701.2.3 fixed over aluminum sheeting, 1.5mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450mm x 450mm x 600mm, 600mm below ground level as per approved drawing and technical specification Clause 801 800mm x 600mm rectangular

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specification and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat Iron 25mm x 5m size on back on edges. The lower plate will be welded with MD angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M -15 grade blocks of 450mm x 450mm x 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube, All MS will be stove enameled on both sides. Lettering and printing arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1.

Earthwork in excavation for foundation for structure as per drawing and technical specification, Clause 305.01 including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal up to a lead of 50m dressing of sides and bottom and backfilling in trenches with excavated suitable material (i) Ordinary Soil A. Manual Mean (i) 3.00m depth.