CERTAIN SPECIAL REPAIR, LBW, REVENUE AND MINOR WORKS AT DAMANA UNDER GE JAMMU

Amount

B/R Portion: - Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in loose / soft soil complete all as specified and as directed.

Material and labour for cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass cement concrete, sub base of floor complete all as specified and as directed.

Material and labour for RCC design mix M-25 as in foundations including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete piles etc complete all as specified and as directed.

Material and labour for RCC design mix M-25 as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and as directed.

Material and labour for RCC design mix M-25 as in roof beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

Material and labour for RCC design mix M-25 as in column, pillars, piers posts and struts etc complete all as specified and as directed.

Material and labour for TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, binding spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Description all as per Ser item No 7.00 here-in-before but 5 to 10mm dia as in stirrups complete all as specified and directed by Engineer-in-Charge.

Material and labour for formwork to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter finished the surface fair complete all as specified and directed by Engineer-in-Charge.

Material and labour for formwork to soffits of suspended slab such as roof slab, floor slab, landing and similar works, not exceeding 200mm thick (Horizontal or sloping) for fair finished complete all as specified and directed by Engineer-in-Charge.

Material and labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc for fair finished complete all as specified and as directed.

Material and labour for formwork to sides of pillars, posts, struts, piers, columns and stanchions etc for fair finished complete all as specified and as directed.

Material and labour for hard core broken to gauge not exceeding 63 mm of broken stone to gauge not exceeding 63mm including as directed before spreading hard core complete all as specified and as directed.

Material and labour for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed.

Description all as per Ser Item No 14.00 here-in-before but except bricks complete all as specified and as directed.

Material and labour for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:6) complete all as specified and as directed.

Material and labour for 75 mm thick PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floors complete all as specified and directed by Engineer-in-Charge.

Material and labour for 75mm thick cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in floor / plinth protection laid in suitable panels finished even and fair all as specified. 6mm joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 grade and three parts of sand (all by weight) complete all as specified and as directed.

Material and labour for rendering 15mm thick in two layers of 10 mm thick in cement mortar (1:6) as base layer and 5mm thick in cement mortar (1:4) on fair faces of brick surface finished even and smooth without using extra cement etc. complete all as specified and as directed. (including all necessary scaffolding, lifting arrangement) with water proofing compound.

Supply only integral liquid water proofing admixture of approved make complete all as specified and as directed.

Material and labour for rendering 10 mm thick in cement mortar (1:6) on fair faces of brick surface finished even and smooth without using extra cement upto height of four storey building complete all as specified and as directed.

Material and labour for rendering 5 mm thick in cement mortar (1:3) on fair faces of concrete surface of ceiling finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing solid PVC door / vent frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet and edges will be painted to match with printed sheet, reinforced with mild steel square tube, supplying and fixing in opening as per specification complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and as directed.

Supply and fixing mild steel butt hinges medium weight 75 mm long complete all as specified and as directed.

Supply and fixing aluminium handle cast type, anodised size 100mm long, 'D' type complete all as specified and as directed.

Supply and fixing aluminium anodised barrel tower bolts, with bright bolt and fixed 200mm complete all as specified and as directed.

Material and labour for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles 350 x 250 / 450 x 300 x 7 to 8 mm thick on vertical surface as in skirting, dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over 10 mm thick back coat in cement mortar (1:4) complete all as specified and as directed.

Supply and fixing 110 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall etc including fixing with clamps complete all as specified and as directed.

Supply and fixing 75 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall including clamps etc complete all as specified and as directed.

Supply and fixing PVC (SWR) bends of bore 110mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) bends of bore 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) junction double (double T) equal or unequal provided with access door of 110 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) junction single (single T) equal or unequal provided with access door of 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) vent cowl of 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) floor trap, plain with grating including jointing with solvent cement of 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

Supply and fixing PVC connection 15 mm size PTMT nuts of length 450 mm complete all as specified and as directed.

Supply and fixing grating doom 125mm dia with waste hole of chromium plated (minimum weight 40 grams) complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing bib taps 15mm dia chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

Supply and fixing stop / angle valves 15mm dia bore of pipe, chromium plated, fancy type, stop valves, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing stop valves 15mm dia bore of pipe, chromium plated, fancy type, with long shank and cap (concealed type) complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts, flush pipe and joints complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC low level flushing cistern valve less, syphonic action type of 10 litres capacity white with inlet, ball valve, float and handle including cast iron brackets, PVC flush pipe 32mm dia, PVC connection (15 x 450 mm) long complete all as specified and as directed.

Supply and fixing vitreous china wash hand basin white, flat back of size 550 x 400mm including cutting for and pinning in, ends of brackets or erecting stand complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing wash hand basin mixer of bore dia of pipe 15mm for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water storage tank including plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 litres including making connections, 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gram) complete all as specified and as directed in SSR Part - I.

Removing excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in hard / dense soil complete all as specified and as directed by Engineer–in-Charge.

Supply and fixing for vitreous china urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including spreader of any colour PTMT complete all as specified and as directed.

Supply and fixing tubular towel rail, 20mm dia, 'D' type 60cm long between flanges of brass chromium plated complete all as specified and as directed.

Supply and fixing brass chromium plated shower rose with arm not less than 125mm dia with or without swivel joints including fixing to steel pipe complete all as specified and as directed.

Supply and fixing figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane of thickness 3mm complete all as specified and as directed.

Supply and fixing PVC waste pipe 32mm dia and suitable length straight or flexible type for wash hand basin / sink complete all as specified and as directed.

Supply and fixing 15mm bore tubes medium grade galvanized ISI marked with all fittings, short pieces and fixed complete to walls and ceiling or laid in floor complete all as specified and as directed.

Supply and fixing galvanised iron tubing 20 mm bore medium grade including all necessary fittings laid in floors or fixed in walls or ceilings complete all as specified and as directed.

Supply and fixing hand shower (health faucet) (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect all as specified and as directed.

Supply and fixing sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Supply and fixing toilet paper holder box type chromium plated complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and as directed.

Material and labour for applying two coats of cement based paint over a coat of primer including preparation of new plastered surface complete all as specified and as directed.

Material and labour for preparing plastered or unplastered new surfaces of walls and applying three coats of white wash complete all as specified and as directed.

Material and labour for cutting into existing manholes for 150mm dia for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished and reforming benching as required complete all as specified and as directed.

Material and labour for precast RCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in manhole cover slab fixed in position including necessary form work and set in cement mortar (1:6) complete all as specified and as directed.

Material and labour for 150mm bore / inner dia double wall corrugated HDPE pipes (SN-4) with integral socket and necessary fttings, laid in trenches jointed as per manufacturer's instructions complete all as specified and as directed at site.

Dismantling asbestos cement (corrugated or semicorrugated etc) sheets in roof covering complete all as specified and as directed.

Material and labour for prepainted galvalume aluminium zinc coating galvanised iron based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material and labour for prepainted galvalume aluminium zinc coating galvanised iron based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section framed work of any description complete all as specified and as directed.

Supply and fixing for structural steel works of Fe-410 W (Grade 'E' 250) quality 'A', as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate / red oxide primer paint (including preparation of surface) before fabrication complete all as specified and as directed.

Material and labour for mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410 W (Grade 'E' 250) quality 'B' complete all as specified and as directed.

Material and labour for mild steel rag or lewis bolts, screwed one end with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, not exceeding 15 cm long complete all as specified and as directed.

Dismantling boarding in any description fixed in any position with nail complete all as specified and as directed.

Supply and fixing for 4mm thick of size 605 X 605 mm, white pre-premiered, self embossed, reinforced designer board for false ceiling conforming to IS-14862 and ISO-8336:1993 fixed / laid / including galvanised iron framework at ceiling with screws framework for ceiling with specification as under mentioned: - (i) GI section frame work (Powder coated) suitable for ceiling board consisting of perimeter wall angle 19mm X 19mm X 0.45mm, cross 'Tee' 28.6mm (web) X 24mm flange 0.33mm thick powdered coated main tee 38mm (Web) X 24mm flange 0.33mm thick. Wall angle shall be screwed / fixed to brick wall / partition wall / concrete / RCC with the help of nylon sleeves and screws @ 610 mm centre to centre, then suspending GI main 'Tee' in both directions by means of hangers / suspenders including 4 GI wires with alignment @ 1220mm centre to centre to soffits. To from grid of 610 X 610mm cross Tee shall be provided @ 610mm centre to centre in both directions and all suitable provisions shall be made for fixing the recessed / surface mounting light fittings if any complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for factory made pressed steel frames of size 105 x 60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete including bottom of each chowkhat to be welded with 02 no's 25x25x3mm angle iron projecting 10cm on either side including one shop coat of red oxide chrome primer and including PCC (1:3:6) type C-0 in back filling of chowkhats and tarring back of chowkhats and holdfasts complete all as specified and as directed.

Material and labour for factory made pressed steel frames of size 125 x 60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete including bottom of each chowkhat to be welded with 02 no's 25x25x3mm angle iron projecting 10cm on either side including one shop coat of red oxide chrome primer and including PCC (1:3:6) type C-0 in back filling of chowkhats and tarring back of chowkhats and holdfasts complete all as specified and as directed.

Supply and fixing 30mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides with lipping / frame to match complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 35mm thick factory made second class hard wood, glazed and skelton shutter open, rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR 2020 Part-I Section 8.24(b) supplied and fitted to chowkhats complete all as specified and as directed.

Supply and fixing mild steel butt hinges medium weight 100 mm long complete all as specified and as directed.

Supply and fixing aluminium handle cast type, anodised size 150mm long, 'D' type complete all as specified and as directed.

Supply and fixing 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing in repair galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Supply and fixing in repair mild steel helical door spring 150mm including roller and roller plate complete fixed with welding to existing / new steel chowkhats complete all as specified and as directed.

Supply and fixing pre-painted (factory painted) box type mild steel windows / Ventilator (factory made) outer frame made out of ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on external side and gauzed shutter fixed with galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm including necessary galvanised iron wire staples etc on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler / AC window complete all as specified and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3 complete all as specified and as directed. Notes: - The quoted rates shall also include: - (i) Two coats of synthetic enamel paint over one shop coat of zinc chromate primer on all exposed surface complete and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. Colour / shade will be approved by Engineer-in-Charge. (ii) 4 no's MS steel lugs made of 20X5 mm Iron flat 200 mm long. (iii) 10 mm Sq Bar grill/guard bar design as per drawing. (iv) PCC block for embedding lugs complete. (v) Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete.

Supply and fixing 3mm thick ordinary glass sheet quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane including punching or drilling out old glazing pins or spring clips and providing and fixing new clips or pins, including scaffolding to reach up to 4 storey building complete all as specified and as directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surface complete all as specified and as directed.

Material and labour for applying two coats of synthetic enamel paint on wooden surface over one coat of pink primer including preparation of new surface over 10cm width or girth complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water and removing unserviceable material outside cantt area complete all as specified and as directed by Engineer-in-Charge. Note: - Rates are deemed to be included for patches work.

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick surface or concrete surface finished even and smooth without using extra cement etc. complete all as specified and as directed. (including all necessary scaffolding, lifting arrangement).

Material and labour for rendering 15 mm thick in cement mortar (1:6) on fair faces of concrete or brick surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for applying two coats of oil bound distemper to newly plastered surfaces including preparation / priming the surfaces and applying two coats of wall putty complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying two coats of oil bound distemper of wall to old plastered surfaces including preparation of surfaces and applying wall putty complete all as specified and as directed.

Material and labour for preparation of old plastered or unplastered surfaces of walls including cornices, pillasters by brooming down or steel wire smoke, root, moulds, moss and efflorescent salts and trading oil and greasy spot by using suitable chemical and removing nails, making good holes with chalk whiting, filling cracks and brooming to remove all dirt etc and applying two coats of cement based paint on old prepared surfaces of walls complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc. complete all as specified and as directed.

Dismantling floors, hearth or wall tilling including cement mortar bedding (but not backing) removing unserviceable materials outside MOD area and rubbish off the premises complete all as specified and as directed.

Material and labour for vitrified tiles dark shade 10mm thick (Square / rectangular) polished, area of each tiles not exceeding 0.36 Sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including screed bed 15mm thick in cement mortar (1:4) complete all as specified and as directed.

Material and labour for vitrified tiles dark shade 10mm thick (square / rectangular) polished, area of each tiles not exceeding 0.36 Sqm, as on vertical surfaces etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including 10 mm thick screed in cement mortar (1:4) complete all as specified and as directed.

Supply and fixing in repair curtain rod stainless steel with fixing brackets (wall or end), side ball stops, funnel, rollers, etc complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Material and labour for RCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate), as in beams / RCC band, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing unserviceable material outside cantt area complete all as specified and as directed by Engineer-in-Charge.

Material and labour for plain cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in copings, bed block etc. and in similar works including weathering, slightly rounded or chamfered angles and throating and necessary form works complete all as specified and as directed.

Excavating in trenches for foundations etc in any type of soil not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and getting out complete all as specified and as directed.

Material and labour for PCC M-10 (nominal mix) (using 40 mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and as directed.

Material and labour for brick work with sub class 'B' bricks using old size bricks having crushing strength not less than 75kg/Sqcm, straight or curved on plan, exceeding 6m mean radius, built in cement mortar (1:4) complete all as specified and as directed.

Material and labour for mild steel posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Grade E-165 complete all as specified and as directed.

Material and labour for galvanised 2 stands, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins, etc. complete all as specified and as directed. Note: - Each line wire to be measured.

Material and labour for framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Grade E-165 complete all as specified and as directed.

Material and labour for rendering 15mm thick on stone masonry surfaces or surfaces other than fair faces of brick work or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc primer complete all as specified and as directed.

Material and labour for providing and fixing concertina coil fencing with punched tape concertina coil 450mm dia, stretched to 6m length having 50 no's spiral turns per 6m length, spring core wire (2.59 mm thick) of high tensile strength of 1620 N / Sqmm with tape (0.52mm thick) hot dip galvanised upto 20 microns, weight of each coil 7.50 to 8.00 kg and fixing the same on existing Y-shaped angle iron with 6 horizontal R.B.T (Reinforced Barbed Tape) wire, stud lied with galvanised iron staple sand galvanised iron clips to retain horizontal, clips shall be @ 5 no's per 2 spiral turns approximate 125 clips per coil including necessary bolts complete all as specified and as directed.

E/M Portion: - Taking down old unserviceable copper / aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden / iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down carefully unserviceable distribution boards of any type / size with MCB's and disconnecting and making good disturbed surfaces complete all as specified and as directed.

Material and labour in replacement for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sqmm for phase and neutral and one run of 6.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase / neutral and one run of cable for earth will be measured and paid as one unit length including taking down old wiring complete all as specified and as directed. Note: - Wiring shall be done in proper colour coding.

Material and labour in replacement for complete point wiring with 1.5 Sqmm single core multistranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 Sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall, plastering after concealing conduit including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc and including making good the disturbed surface as per existing complete all as specified and as directed by Engineer-in-Charge for the following:-

Description all as per Ser item No 119.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board ISI marked complete all as specified and as directed.

Description all as per Ser item No 119.00 here-in-before but for multi 5 pin socket outlet 5 amp socket on independent board ISI marked complete all as specified and as directed.

Description all as per Ser item No 119.00 here-in-before but for multi 6 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green color complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement modular socket, 6A - 5 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular switch 1 module 6 A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement ceiling rose, 3 Pin / PVC / polycarbonate isolated body ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular switch 1 way 16A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular socket 6A/16A - 6 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Material and labour in replacement for lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Material and labour in replacement of self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

Supply and fixing in replacement of LED lights fitting 1 x 18W, 220V, AC decorative box type complete with LED tube rod 18 watts driver, holder and power factor >0.9, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Material and labour for replacement of distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Supply and fixing in replacement SPN 40 to 63 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 6 to 32 Amp complete with connection, testing and commissioning complete all as specified and as directed.

Material and labour in replacement for Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 metre deep below normal ground level with top edge of the earth plate not less than 1.5 metre below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 precast RCC cover slab using reinforcement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and as directed.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing in replacement fan step regulator, 100W - 1 module 240 volts ISI marked complete all as specified and as directed.

Disconnecting and taking out defective service cable of any size and any type from roof, pole, pipe, floor, wall etc complete all as specified and as directed.

Supply and laying, connecting and testing XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 16 Sqmm 4.0 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc. complete all as specified and as directed. Notes: - (i) Earth work, sand, bricks, removing, returning filling, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new / existing pipes are to be provided by the contractor without any extra cost.

Material and labour for point wiring for one light / fan / call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into new concealed PVC rigid / steel conduit and into existing cast iron / pressed steel sunken / terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Notes: - (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engineer-in-Charge.

Description all as per Ser item No 140.00 here-in-before but for one 5 pin socket outlet, 5amps, independent complete all as specified and as directed.

Description all as per Ser Item No 140.00 here-in-before but for one 5 pin socket outlet 15 Amps on independent board with cables 2.5 Sqmm size complete all as specified and as directed.

Supply and fixing switch piano, flush type single pole one way 5 Amp, 240 volts complete all as specified and as directed.

Supply and fixing switch socket outlet combined 5 pin 5 amp flush type, 240 volts complete all as specified and as directed.

Supply and fixing switch socket outlet combined 2 in 1, 3 pin 5 amp and 15 amp flush type, 240 volts complete all as specified and as directed.

Supply and fixing ceiling rose 3 terminal surface type complete all as specified and as directed.

Supply and fixing LED lights fitting 1 x 20W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and as directed.

Material and labour for distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 4 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Supply and fixing 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing SPN 40 to 63 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and laying, connecting and testing serviceable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 10 Sqmm 2.0 core complete from pole to building complete all as specified and as directed.

Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and as directed.

Material and labour for fixing of 4 No's rawl plug of suitable size (4"-6") nuts and bolts for hanging of geysers on wall complete all as specified and as directed.

Supply and fixing PVC connection of size 15 mm dia with PTMT nuts of length 450 mm long (hot series braided, threaded and cold series) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 metre deep below normal ground level with top edge of the earth plate not less than 1.5 metre below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 precast RCC cover slab using reinforcement with suitable handle made of round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP-65/66 protection complete all as specified and as directed.

Supply and fixing exhaust fan, steel body AC single phase, 230V of size 300m sweep with blades and frame and louvers complete with louver shutter including fixing rawl plug / nut and bolts complete all as specified and as directed.

bushan kumar (BID ID -3089429)

M/s Koul & Sons (BID ID -3093539)

M/S RAKESH CONSTRUCTION (BID ID -3095311)

Mehta Enterprises (BID ID -3087061)

STAR CONSTRUCTIONS (BID ID -3095236)

M/s ATHARAV ELETCTRICALS (BID ID -3088238)