16(NIeT)/PRDD (15CFC)/ZP/T/UtF)/GTA/2025-26

Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing,spreading or stacking the spoils within a lead of 75m.as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1.500 mm.

Earth work in filling in foundation trenches or plinth with good earth in layers not exceeding 150 mm. including watering and ramming etc.layer by layer complete .(payment to be made on the basis of measurement of finished quantity of work).(a) With earth obtained from excavation of foundation.

Laying 150 mm. to 200 mm. boulder soling including rough dressing hand packing and ramming down small pieces in the interstics without rolling but including ramming.

Cost of stone boulder 150 mm size delivered ans stacked at site.

(I) Cement concrete with graded stone ballast (40 mm size) excluding shuttering.In ground floor.(B) With N.B variety stone metal.

Ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes.(b) River bazree.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction.(a) For works in foundation, basement and up to roof of ground floor/up to 4m. Tor steel/Mild steel.other than SAIL/TATA/RINL/JSW/JSPL/Shyam/SRMB/ISSL/BMASL/Electrosteel

Hire and labour charge for shuttering with centreing and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thick ness with required bracing for concrete slabs, beams, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (up to roof of ground floor).(a) 25 mm. to 30 mm. thick wooden shuttering as per decision & direction of the Engineer-in-charge. .

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.

Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface].(ii) With 1:4 cement mortar .(a) 20 mm.thick plaster.

Supplying, fitting and fixing windows and ventilators with or withoutintegrated grills conforming to IS 1038-1975 and manufactured fromrolled steel sections conforming to IS 7452-1974 with non-frictionprojecting type, box type hinges, glazing clips, lugs locking bracket,handle plate etc, including hoisting in position, straightening ifrequired, fixing lugs in cement concrete ( 1:2:4) with stone chips 20mm down cutting holes and mending good damages to match withexisting surface complete in all respect excluding glazing.(Add extra @ 1.2 % for each additional floors upto 4th floor and @1.5% for each addl. Floor above 4th floor.)In Ground floorFlash butt welded windows and ventilators(No shop priming will be allowed to facilitate inspection ofworkmanship)Without integrated grill (b) Openable steel windows as per IS sizes with side hung shuttersand horizotal glazing bars. [The extra rate admissible for theopenable portion only]

Providing and fixing factory made door frame (single rebate) made of singlepiece extruded solid PVC profile with homogenous fine cellular structure havingsmooth outer integral skin having 62mm width x 32 mm thickness (the door frameis to be made with single piece extruded solid pvc profile whereas no sheet pastedprofile shall be applied for door frame fabrication) and shall be fixed to wall asper instructions of Engineer – in – charge using 100 x 8 sheet metal CSK screws.

Supplying, Fitting & Fixing 30 mm thick Factory made moulded Door shutter,consisting of solid core single leaf flash door of 30 mm thickness lipped with 15mm [5mmx3] thick x 30 mm wide on one style and top rail and 10 mm [5mmx2]thick x 30 mm wide of the other style and bottom rail. The inner panel laminatedwith 2 mm thick termite proof water proof and fire resistant moulded PVC sheetwith raised panel designed in different plain/ or Prelam colour on one side afterrouting the moulded design on flash door and 2mm plain and or Prelam PVCsheet on other side using rubber adhesive on flash door and solvent cementadhesive on the PVC lipping etc. complete excluding hardwares as necessary asper direction of Engineer-in Charge, Manufacturer‟s Specification and drawing..In ground floor.(a) Moulded door using 2 mm moulded PVC sheet or 2 mm etched moulded PVCsheet on one side & 2 mm PVC sheet on other side.

(a) M.S. or W.I. ornamental grill of approved design joints continuously welded with M.S., W.I. flats and bars for windows ,railing etc. fitted and fixed with necessary screws and lugs in ground floor. (Add extra @1% for each addl. floor up to 4th floor and @1.25% for each addl. floor above 4th floor). (i) Grill weighing above 10 kg./sq.m.and up to 16kg/sq.m.

Supplying,Fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m.(a) Area of each tile up to 0.09Sq.m.(ii) Other than Coloured decorative including white.

Supplying,Fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m.(a) Area of each tile upto 0.09Sq.m.(ii) Other than Coloured decorative including white.

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing).580 mm X 440 mm.

Supplying, fitting and fixing Flat back urinal (half stall urinals) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete.470 mm X 280 mm X 340 mm.

Supplying, figging and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete(6:3:1) with jhama chips complete.(Payment of concrete will be paid seperately).450 mm X 350 mm.

Supplying, fitting and fixing cast iron 'P' or 'S' trap conforming to I.S. 3989/1970 and 1729/1964 including lead caulked joints and painting two coats to the exposed surface. (Painting to be paid seperately).P' Trap.100 mm.

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 .Single socketed 3 meter length.110 mm.

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 .Fittings.Plain tee.110 mm.

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 .Fittings.Door Bend (T.S).110 mm.

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 .Fittings.Vent Cowl.110 mm.

Supplying, fitting and fixing CPVC (Chlorinated PolyvinylChloride) pipes of approved make conforming to IS-15778:2007 . with all necessary accessories, specials viz. socket,bend, tee, union, cross, elbo, nipple, longscrew, reducingsocket, reducing tee, short piece etc. fitted with holder batsclamps, including cutting pipes, fitting, fixing etc. completein all respect including cost of all necessary fittings asrequired,jointing materials in any position above ground.(Payment will be made on the centre line measurements oftotal pipe line including all specials. No separate paymentwill be made for accesories, specials.(a) For Exposed Work For exposed work (i) CPVC Pipes Class-I,SDR-11 50 mm

Supplying, fitting and fixing CPVC (Chlorinated PolyvinylChloride) pipes of approved make conforming to IS-15778:2007 . with all necessary accessories, specials viz. socket,bend, tee, union, cross, elbo, nipple, longscrew, reducingsocket, reducing tee, short piece etc. fitted with holder batsclamps, including cutting pipes, fitting, fixing etc. completein all respect including cost of all necessary fittings asrequired,jointing materials in any position above ground.(Payment will be made on the centre line measurements oftotal pipe line including all specials. No separate paymentwill be made for accesories, specials.(a) For Exposed Work For exposed work (i) CPVC Pipes Class-I,SDR-11 20 mm

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (B) Socket 50 mm

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (B) Socket 20 mm

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (I) Tank connecting nipple 50 mm

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (J) Male threaded adopter 20 mm

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (C) Equal Tee 50 mm

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (K) Elbow (90°) 50 mm

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (F) Reducing Bush 50 mm X20mm

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (K) Elbow (90°) 20 mm

Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm(depth) with 250 mm thick 1st. class brick work in cement mortar(4:1) on all sides, bottom of the pit consisting of 100 mm thick cement concrete(1:6:3) with stone chips over a layer of jhama brick flat soiling, 15 mm thick (1:4) cement plaster to inside walls and outside walls upto G.L. and 20 mm thick(1:4) plaster to bottom of the pit, providing necessary invert with cement concrete(1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster(1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials.with Bazree (Pakur Variety). (JSW/JSP/SHYAM /SRMB/BMASL/ELECTROSTEEL/SSL)

Construction of Septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (4:1) including two 560 mm dia. R.C.C. manhloe cover of approved make supplied, fitted and fixied in the top slab with necessary fittings, 19 mm thick cement plaster(4:1) with neat cement finish to the internal surfaces and 12 mm thick plaster(4:1) to outside wall upto 200 mm below G.L. floor finished with 25 mm thick grey artificial stone including supplying, fitting and fixing all necessary specials, fittings, S.W. tees, C.I. foot rest etc. including excavating earth in all sorts of soil, shoring, bailing and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tank with earth, removing spoils, fliing up the chamber with clear water, removing foreign materialsfrom the chamber and including constructing attached inspection pit as per approved dawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 5% by weight of cement, complete in all respect as per directon of Engineer-in-Charge.For 50 users.With Pakur variety (OTHER MANUFACTURES NOT SPECIFIED)

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work(6:1) band all round and cement brick work(6:1) upto 0.90 metre from top with 19 mm thick cement plastering(4:1) to inside face upto the depth of cement brick work, 12 mm thick cement plaster(4:1) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal(50 mm to 63 mm size) including R.C.C. cover slab of designed thickness with cement concrete(4:2:1) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making necessary arrangements for pipe conections, excavation of well including shoring, dewatering and remeving the excess earth from the premisis as per direction complete in all respect with all costs of labour and materials.With 250 mm thick dry brick work and 250 mm thick cement brick work(6:1) and 1.00 m. inside dia.(OTHER MANUFACTURES NOT SPECIFIED)

Supplying PVC water storage tank of approved quality with closed top weith lid (Black) - Multilayer.1000 litre capacity.

Supplying, fitting and fixing bib cock or stop cock.Chromium plated Bib Cock long body with wall flange with aerator (Equivelent to Code No.512 & Model- Tropical /sumthing special of ESSCO or Similar brand).

Plum Concrete work with 40 % Cement Concrete with 30 mm down graded stone metal and 60% stone boulder of size 150 mm and above, placed in position as directed excluding shuttering if any.(i) (1:3:6) proportion.

Add 18% GST on total (Rs.835964.46)

Add 1% CESS on total (Rs.986438.06)

Please Enable Macros to View BoQ information