Renovation of Workers Canteen at Helicopter Division, HAL HC.

HINDUSTAN AERONAUTICS LIMITED BANGALORE FACILITIES MANAGEMENT DIVISION

NAME OF THE WORK: Renovation of Workers Canteen at Helicopter Division, HAL [HC]. CONTRACT NO. HAL/FMD/R-106/24-25

Name of the Contractor :

Sl. No. Specification Quantity Unit Rate in Figs [Excluding GST] Rate in Words Amount

Preamble: (1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The Tenderer shall abide by prevailing GST act. (2) L1 (lowest quote) will be determined based on the total quoted amount including GST. (3) This BOQ specification has to be read in conjunction with relevant CPWD specification amended upto date/ detailed technical specification in tender document and tender drawings if any.

Part 'I' - Civil Works

1 Earth work in excavation in all kinds of soil by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.50m in width as well as 10Sq m on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc., all complete as per directions of the Engineer-in-Charge. 14.00 Cu m 163.07 Rupees One Hundred Sixty Three and Seven Paise Only 2283.04

2 Providing and laying in position reinforced cement concrete of 1:2:4 grade 4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources) all works upto plinth level excluding the cost of centering, shuttering and reinforcement but including curing, carriage for all leads; hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc., all complete as per the directions of Engineer in Engineer-in-Charge. 25.00 Cu m 7885.82 Rupees Seven Thousand Eight Hundred Eighty Five and Eighty One Paise Only 197145.42

3 Supplying, fabrication and fixing in position of TMT reinforcement bars of grade Fe-500D or more for R.C.C work above plinth level including straightening, cutting, bending, hooking, cranking, placing in position, lapping wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) including all lead and lift, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc.., all complete as per directions of the Engineer-in-Charge. 575.00 Kgs 99.08 Rupees Ninety Nine and Eight Paise Only 56973.82

4 Repair to plaster of thickness 12mm to 20 mm in patches of area 2.50Sq m and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, etc., all complete as per the direction of Engineer-in-Charge. 190.00 Sq m 616.42 Rupees Six Hundred Sixteen and Forty Two Paise Only 117120.01

5 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade of one or more coats on old work including preparation of surfaces, etc., all complete as per directions of the Engineer-in-Charge. 750.00 Sq m 94.45 Rupees Ninety Four and Forty Four Paise Only 70833.99

6 Providing and applying two coats of wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including preparation of surfaces, etc., all complete as per direction of the Engineer-in-Charge. 850.00 Sq m 126.28 Rupees One Hundred Twenty Six and Twenty Seven Paise Only 107337.38

7 Providing and fixing Powder coated aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket, etc., Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, etc., all complete as per architectural drawings and the directions of Engineer-in-Charge.

a) For Fixed Portion 540.00 Kgs 487.75 Rupees Four Hundred Eighty Seven and Seventy Five Paise Only 263386.69

b) For shutters including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required. 350.00 Kgs 582.89 Rupees Five Hundred Eighty Two and Eighty Eight Paise Only 204010.62

8 Providing and fixing glazing with float glass panes of 5mm thickness (weight not less than 12.50 kg/Sq m) in aluminium door, window, ventilator shutters and partitions, etc., with EPDM rubber / neoprene gasket, etc., all complete as per the architectural drawings and the directions of Engineer-in-Charge. 90.00 Sq m 1382.92 Rupees One Thousand Three Hundred Eighty Two and Ninety One Paise Only 124462.49

9 Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6mm and down size or pea sized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading complete with Bitumen felt (hessian base) type 3 grade I conforming to IS : 1322, etc., all complete as directed by Engineer-in-Charge. Note: A performance guarantee bond for 3 years on non-judicial stamp paper of Rs. 500/- shall be given by the contractor. The 10% of completed value of this item shall be dedcuted as defect liability deposit and the same shall be returned after sucessful completion of 3 years from the date of completion of contract / project as a whole. 290.00 Sq m 473.19 Rupees Four Hundred Seventy Three and Nineteen Paise Only 137225.47

10 Supplying and fixing of [455 x 610]mm rectangular C.I. cover for manholes (light duty) the weight of the cover to be not less than 23Kgs without frame, etc., all complete as directed by Engineer-in-Charge. 1.00 Each 1247.63 Rupees One Thousand Two Hundred Forty Seven and Sixty Three Paise Only 1247.63

11 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates, etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts, etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-Charge, (Note : For payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners, etc.,) 300.00 Kgs 709.63 Rupees Seven Hundred Nine and Sixty Two Paise Only 212887.84

12 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as aproved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.30Kgs per Sq m, including pointing in white cement mixed with pigment of matching shade, etc., all complete as directed by Engineer-in-Charge. 70.00 Sq m 1164.90 Rupees One Thousand One Hundred Sixty Four and Ninety Paise Only 81543.15

13 Providing and Laying in position Cement Concrete of 1:4:8 (1 cement : 4 coarse sand (zone3) derived from natural sources : 8 graded stone aggregate of 40mm nominal size derived from natural sources) excluding the cost of centering and shuttering for all work upto plinth level including all lead and lift, hire charges of machinery and equipments, curing, cost of all materials, labour charges and all other incidental charges, etc., all complete as per the directions of Engineer-in-Charge. 7.00 Cu m 6258.38 Rupees Six Thousand Two Hundred Fifty Eight and Thirty Eight Paise Only 43808.66

14 Providing & Constructing of Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level with cement mortar (1:6) including levelling curring, etc., all complete as directed by Engineer-in-Charge. 10.00 Cu m 6717.06 Rupees Six Thousand Seven Hundred Seventeen and Five Paise Only 67170.56

15 Centering and shuttering including strutting, propping etc. and removal of form work for foundations, footings, bases of columns, etc., for mass concrete, etc., The rate quoted shall include all lead, lift, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc., all complete as per the directions of the Engineer-in-Charge. Note: Form work material contractors own property and shall be removed after completion of work. 5.00 Sq m 360.28 Rupees Three Hundred Sixty and Twenty Seven Paise Only 1801.40

16 Providing and laying autoclaved aerated cement blocks masonry with 150mm to 300mm thick with grabde-1 AAC blocks of density 551 to 650 Kgs / Cu m conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar, etc., all complete as per direction of Engineer-in-Charge. 12.00 Cu m 7656.36 Rupees Seven Thousand Six Hundred Fifty Six and Thirty Six Paise Only 91876.37

17 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per Sq m as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer in-Charge. The sheet shall be fixed using self drilling /self tapping screws of size [5.50 x 55]mm with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required, all lead & lift, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc.., all complete as per the directions of the Engineer-in-Charge. Note: A performance guarantee bond for 5 years on non-judicial stamp paper of Rs. 500/- shall be given by the contractor. The 10% of completed value of this item shall be dedcuted as defect liability deposit and the same shall be returned after sucessful completion of 5 years from the date of completion of contract / project as a whole. 60.00 Sq m 678.62 Rupees Six Hundred Seventy Eight and Sixty One Paise Only 40717.14

18 Supply, Fabrication & Erection of Structural steel work in single section, fixed with or without connecting plate without any damage to itself and surroundings including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, all lead & lift, hire charges of machinery and equipments, charges for providing & removing scaffolding wherever required, cost of all materials, labour charges and all other incidental charges, etc.., all complete as per the directions of the Engineer-in-Charge. 610.00 Kgs 107.81 Rupees One Hundred Seven and Eighty One Paise Only 65765.82

19 Providing and laying Brick work in position with Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in Cement mortar 1:4 (1 cement :4 coarse sand) including all lead and lift, hire charges of machinery and equipments, charges for providing & removing scaffolding wherever required, racking out joints 10mm deep to receive plaster, curing, cost of all materials,labour charges and all other incidental charges, etc., all complete as per directions of the Engineer-in-Charge. 22.00 Sq m 1032.47 Rupees One Thousand Thirty Two and Forty Six Paise Only 22714.28

20 Providing and laying vitrified floor tiles in size [600 x 600]mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.30Kgs / Sq m including grouting the joints with white cement and matching pigments, etc., all complete as per direction of Engineer-in-Charge. 175.00 Sq m 1427.20 Rupees One Thousand Four Hundred Twenty Seven and Nineteen Paise Only 249759.87

21 Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Granite stone slab colour black, Cherry / Ruby red (area of slab over 0.50Sq m) for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish, etc., complete at all levels as directed by Engineer-in-Charge. 13.00 Sq m 4718.87 Rupees Four Thousand Seven Hundred Eighteen and Eighty Six Paise Only 61345.27

22 Providing and fixing Stainless Steel kitchen sink wih drain board of size [510 x 1040]mm bowl depth 250mm A ISI 304 (18/8) as per IS:13983 with C.I. brackets and stainless steel plug 40mm, including painting of fittings and rackets, cutting and making good the walls wherever required, etc., all complete as directed by Engineer-in-Charge. 2.00 Nos 6381.12 Rupees Six Thousand Three Hundred Eighty One and Twelve Paise Only 12762.25

23 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of nominal dia 20mm, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints, etc., all complete as per direction of Engineer-in-Charge. 60.00 R m 252.01 Rupees Two Hundred Fifty Two Only 15120.44

24 Providing and fixing 75mm diameter on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion single socketed pipes, etc., all complete as directed by Engineer-in-Charge. 30.00 R m 228.58 Rupees Two Hundred Twenty Eight and Fifty Seven Paise Only 6857.39

25 Providing and fixing 110mm diameter on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion single socketed pipes, etc., all complete as directed by Engineer-in-Charge. 30.00 R m 346.73 Rupees Three Hundred Forty Six and Seventy Two Paise Only 10401.85

26 Providing and fixing Kiln seasoned and chemically treated hollock wood frame work consisting of battens [50 x 25]mm fixed with rawl plug and drilling necessary holes for rawl plug, etc., including priming coat all complete as directed by Engineer-in-Charge. 0.07 Cu m 172057.37 Rupees One Lakh Seventy Two Thousand Fifty Seven and Thirty Seven Paise Only 12044.02

27 Providing and fixing ISI marked 30mm thick including ISI marked Stainless Steel butt hinges with necessary screws flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters, etc., all complete as directed by Engineer-in-Charge. 2.25 Sq m 2910.49 Rupees Two Thousand Nine Hundred Ten and Forty Eight Paise Only 6548.60

28 Demolishing brick work (in cement mortar) manually / by mechanical means without causing any damage to the surroundings including stacking of serviceable material and disposal of unserviceable material within 50metres lead, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc., all complete as per directions of the Engineer-in-Charge. 19.00 Cu m 1892.77 Rupees One Thousand Eight Hundred Ninety Two and Seventy Six Paise Only 35962.54

29 Demolishing cement concrete manually / by mechanical means without causing any damage to the surroundings including disposal of material within 50metres lead, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc., all complete as per directions of the Engineer-in-Charge. 9.00 Cu m 1381.40 Rupees One Thousand Three Hundred Eighty One and Forty Paise Only 12432.61

30 Demolishing R.C.C. work manually / by mechanical means without causing any damage to the surroundings including stacking of steel bars and disposal of unserviceable material within 50 metres lead, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc., all complete as per directions of the Engineer-in-Charge. 3.00 Cu m 3262.64 Rupees Three Thousand Two Hundred Sixty Two and Sixty Three Paise Only 9787.91

31 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50metres lead (area 3Sq m and below), The rate quoted shall include all lead, lift, hire charges of machinery and equipments, charges for providing & removing scaffolding wherever required, cost of all materials, labour charges and all other incidental charges, etc., all complete as per the directions of the Engineer-in-Charge. 32.00 Each 131.84 Rupees One Hundred Thirty One and Eighty Three Paise Only 4218.80

32 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50metres lead (beyond area of 3Sq m), The rate quoted shall include all lead, lift, hire charges of machinery and equipments, charges for providing & removing scaffolding wherever required, cost of all materials, labour charges and all other incidental charges, etc., all complete as per the directions of the Engineer-in-Charge. 3.00 Each 173.55 Rupees One Hundred Seventy Three and Fifty Four Paise Only 520.64

33 Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding, etc. including dismembering and stacking within 50metres lead, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc., all complete as per directions of the Engineer-in-Charge. 165.00 Kgs 5.19 Rupees Five and Nineteen Paise Only 856.48

34 Dismantling tile work in floors and roofs for thickness of tiles 10mm to 25mm laid in cement mortar without causing any damage to the surroundings including stacking of serviceable material and disposal of unserviceable material within 50metres lead, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc., all complete as per directions of the Engineer-in-Charge. 8.00 Sq m 67.43 Rupees Sixty Seven and Forty Three Paise Only 539.48

35 Dismantling asbestos cement roofing sheets including ridges, hips, valleys and gutters, etc., without causing any damage to the surroundings including stacking of serviceable material and disposal of unserviceable material within 50metres lead, hire charges of machinery and equipments, cost of all materials, labour charges and all other incidental charges, etc., all complete as per directions of the Engineer-in-Charge. 20.00 Sq m 71.02 Rupees Seventy One and One Paise Only 1420.35

36 Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) of size [100 x 63 x 4]mm transparent or dyed to required colour or shade with necessary screws, etc.. all complete as directed by Engineer-in-Charge. 4.00 Each 96.24 Rupees Ninety Six and Twenty Three Paise Only 384.95

37 Providing and fixing aluminium tower bolts of size [200 x 10]mm, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws, etc., all complete as directed by Engineer-in-Charge. 2.00 Nos 91.60 Rupees Ninety One and Fifty Nine Paise Only 183.19

38 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701mm to 1000mm), with double speed adjustment with necessary accessories and screws, etc., all complete as directed by Engineer-in-Charge. 1.00 Each 903.25 Rupees Nine Hundred Three and Twenty Four Paise Only 903.25

39 Providing and fixing aluminium handles of length 125mm, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws, etc., all complete as directed by Engineer-in-Charge. 2.00 Nos 60.87 Rupees Sixty and Eighty Six Paise Only 121.73

40 Providing and fixing bright finished brass 100mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws, etc., all complete as directed by Engineer-in-Charge. 1.00 Each 785.19 Rupees Seven Hundred Eighty Five and Nineteen Paise Only 785.19

41 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations, etc., in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50m and lift upto 1.50m, etc., all complete as per directions of the Engineer-in-Charge. 30.00 Cu m 180.07 Rupees One Hundred Eighty and Seven Paise Only 5402.13

42 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50m initial lead, for all leads including all lifts involved all complete as per directions of the Engineer-in-Charge. 45.00 Cu m 242.50 Rupees Two Hundred Forty Two and Forty Nine Paise Only 10912.43

Sub-Total of Part I - Civl Works (Excluding GST) Rupees Twenty Three Lakh Sixty Nine Thousand Five Hundred Eighty Three and Seventeen Paise Only 2369583.17

Part 'II' - Electrical Works

1 Supply & fixing on existing MS hook 1200mm sweep,Five star rated with brushless direct current motor(BLDC) Ceiling fans complete with blades, down rods, and accessories, 230V single phase 50Hz AC supply. Minimum air delivery 210cu.m/min with service value 6.00 BEE , erected in position with necessary flexible copper leads of required colour and with canopy, down rod 300mm to 600mm length as per site requirement , necessary rubber bushings, clamps nuts,bolts etc., complete in all respects and as directed by Engineer-in-charge. 25.00 Nos 2642.57 Rupees Two Thousand Six Hundred Forty Two and Fifty Six Paise Only 66064.19

2 Supply & fixing on wall using suitable mounting arragements, fixing hardwares, testing and commissioning of 450mm dia, wall mounting, oscillating type fan along with speed regulator, power cord with 6A, 3 pin plug top and other connected accessories etc., including necessary interconnections complete in all respects and as directed by the Engineer-in-charge. 15.00 Nos 4252.54 Rupees Four Thousand Two Hundred Fifty Two and Fifty Four Paise Only 63788.14

3 Supply, installation, testing & commissioning of 300mm dia 900 rpm heavy duty exhaust fan of any approved make with louvers, connecting cord with 6A, 3 pin plug top and with all necessary accessories, including making wall openings and replastering to smooth finish with matching paint etc., complete in all respects and as directed by Engineer-in-charge. 10.00 Nos 4102.69 Rupees Four Thousand One Hundred Two and Sixty Nine Paise Only 41026.90

4 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. 50.00 Mtrs 40.65 Rupees Forty and Sixty Five Paise Only 2032.63

5 Earthing with G.I. earth pipe 4.5metre long, 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. 2.00 Nos 6635.46 Rupees Six Thousand Six Hundred Thirty Five and Forty Five Paise Only 13270.92

Sub-Total of Part II - Electrical Works (Excluding GST) Rupees One Lakh Eighty Six Thousand One Hundred Eighty Two and Seventy Seven Paise Only 186182.77

Sub-Total of Part I + Part II (Excluding GST) Rupees Twenty Five Lakh Fifty Five Thousand Seven Hundred Sixty Five and Ninety Four Paise Only 2555765.94

The Tenderer has to Quote Percentage Above / Below as Specified and Percentage Shall be Quoted in Figures. Approximate Amount Put to Tender State Above or Below Percentage in Figures [Excluding GST] Amount

Tenderer's Quote (Excluding GST) 2555765.94 BELOW % 2555765.94

Add 18% GST Rupees Four Lakh Sixty Thousand Thirty Seven and Eighty Seven Paise Only 460037.87

Grand Total (Including GST) Rupees Thirty Lakh Fifteen Thousand Eight Hundred Three and Eighty One Paise Only 3015803.82

Note: The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered.

WARNING: PLEASE ENTER PERCENTAGE QUOTE

HINDUSTAN AERONAUTICS LIMITED

Facilities Management Division

Pre-Qulification Profile (To Be uploaded along with Part A)

Tender Ref No. or Contract No.: HAL/FMD/R-106/24-25

Name of Work: Renovation of Workers Canteen at Helicopter Division, HAL [HC].

Estimated Amount in Rs.: 3020000

Tender Notice Date : 23.11.2024

PROVISIONAL GST ID NO. for HAL 29AAACH3641R1Z3

Sl.No Description Details Enclosed / Not Enclosed Remarks

1 Name of the Individual / Firm / Company: * Mandatory Please Enter Name of the Individual/firm/company

2 Type of ownership PlsEnter Type of Ownership

If Other, please specify

3 Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc., Pls enter Details of Constitution

4 Address for correspondence: Pls Enter Address

5 (a) PAN No.: Pls Enter Pan NO

5 (b) Service Tax Registration No

5 (c ) Goods and Service Tax ID No.

6 Contact details

Contact person name Please Enter Contact person Name

Mobile No. Pls Enter Mobile No

Ph. No. with STD code

FAX No. with STD code 3 #N/A

7 Registered Contractor

If Registered Contractor with HAL Yes/ No Related Document to be Uploaded to eProcurement Portal * Category: E= 75 Lakhs - Lessthan= 100Lakhs F= 50Lakhs - Lessthan 75 Lakhs G = 25Lakhs - Lessthan 50 Lakhs H = 10Lakhs - Lessthan 25 Lakhs I = 5Lakhs - Lessthan 10 Lakhs J = 2Lakhs - Lessthan 5 Lakhs K = Lessthan 2Lakhs 0 7 E 1

Registration No. 199999 7 F 2

Category 200000 6 G 3

PEMD Amount ( If paid ) 499999 6 H 4

8 I.T Returns for past 03 years 999999 5 J 6

2024-25 Pls Select 'Yes' ' No' for IT Return for All Three years 1000000 4 K 7

9 Average annual financial turn over during the last 3 years, ending 31st March 2024 of the previous financial year [ should not be less than 30% of Amount put to tender] 4999999 3

YEAR TURN OVER IN Rs. Enclosed / Not Enclosed REMARKS 5000000 2

2023- 2024 Rs. Pls Enter Turn over in Rupees for all the 3 years 7499999 2

Average annual Financial turn over 0.00 906000.00

Avg Annual Turnover criteria is not met 10000000 1

10 ESI & PF Nos with proof Nos Enclosed / Not Enclosed

ESI Registration No/. with proof if any Remarks if any

PF Registration No. with proof if any

11 Bank(s) details: [Copy of the cheque leaf to be uploaded]

Bank Account No. Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)

Name of the Bank

Type of Account

12 Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the last date of Tender submission solvency cal

Name of Bank & Branch Pls Enter Details to 'Name of the Bank' , 'Date of Issue','Value in Rs #REF! 28-Jun 0 40000

Date of Issue 200000 40000

Value in Rs. 200001 150000

Solvency value is NOT as per NIT

13 Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender. 1208000 500001 250000

Completed similar works during last 7 years Pls Select %of similar works completed during last 7 years 1000000 250000

Work NoI Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 1000001 500000

Brief Description of Work: Please enter Details for Work No 1 2000000 500000

Completed value of Work in Rs. 2000001 1000000

Date of Commencement of Work 4000000 1000000

Date of Actual Completion of Work: 4000001 2000000

Work No II Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 10000000 2000000

Brief Description of Work: Pls Enter Details for Work No II

Completed value of Work in Rs.

Date of Commencement of Work:

Date of Actual Completion of Work: work done

Work No III Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal #REF! 2555

Brief Description of Work: Pls Enter Details for Work No III #REF!

Completed value of Work in Rs.

Date of Commencement of Work:

Date of Actual Completion of Work:

14 Details of person holding the power of Attorney (If different from contact person)

Name Related Document to be Uploaded to eProcurement Portal

Mobile No. Pls Enter Details for Person holding Power of Attorney

Ph. No. with STD code

FAX No. with STD code

15 DECLARATION I

The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions including price bid do hereby accept all the terms and conditions laid down in the said Tender document and will abide by the same on acceptance and ward of work.

16 DECLARATION II

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer. 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. Pls Accept the Delaration II