PROVN OF PARKING SHED AT VARIOUS LOCATION IN DOMESTIC AREA AND CERTAIN MAJOR AND MINOR REVENUE WORKS AT AFS PURNEA UNDER AGE (I) (AF) PURNEA

Amount

Job No-14FBSU/LBWP/MD ACCN NEW/02/2020-21,14FBSU/MAJ REV/01,02/2020-21 Excavation in post holes (or similar holes) each n.exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n.exc 50m and making good surface (Soft/loose soil) complete all as specified and as directed by Engr-in-Charge.

M&L for MS tubes steel work in tubular purlins, framed truss, post, rafters ect including butt welded tubes conforming to I.S 1161-1998 graded St-240 including necessary holding down bolts or hold fasts and welding with and incl nut & bolts as required complete all as specified and as directed by Engr-in-Charge.

M&L for Pre-painted galvatume aluminum zink coating GI based corrugated steel sheet 0.45 to 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as complete all as specified and as directed by the Engr-in-charge.

M&L for Pre-painted galvatume aluminum zink coating GI based plane steel sheet 0.45 to 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as complete all as specified and as directed by the Engr-in-charge.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surface of any description, over 10 cm in width complete all as specified and as directed by the Engr-in-charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point soft/loose soil complete all as specified and as directed by the Engr-in-charge.

M&L for cement concrete type E-2, 1:5:10 type E-5 (using 40mm graded aggregate) as in foundation filling and mass concrete of post holes complete all as specified and as directed by Engr-in-Charge.

Surface excavation n. exc 30 cm deep and averaging 25 cm deep and getting out complete all as specified and as directed by the Engr-in-charge.

Hardcore of broken stone boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by the Engr-in-charge.

100 mm thick Cement concrete 1:4:8, type D-2 (40mm graded aggregate) finish even & smooth without using extra cement complete all as specified and as directed by the Engr-in-charge.

100 mm thick Cement concrete 1:2:4 type B-2 (40mm graded aggregate) finish even & smooth without using extra cement complete all as specified and as directed by the Engr-in-charge.

S & F Glass dividing strips,38mm wide 3 mm thick in pattern as per site complete all as specified and as directed by the Engr-in-charge.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed by the Engr-in-charge.

S & F MS Bolt with Nut of 16 to 20mm dia, 30cm long complete all as specified and directed by the Engr-in-charge.

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long Bolt with Nut of 5 to 10mm dia, 50mm long complete all as specified and directed by the Engr-in-charge.

Surface dressing n.exc (not exceeding) 15 cm deep in soft /Loose soil.

M & L Cement concrete in foundations, filling and mass concrete Type D2 1:4:8 (40 mm graded aggregate)

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 as specified

S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Fe-410- W(Gde- E-250) quality- B

M & L cement concrete type C1 1:3:6 75 mm thick as in plinth protection

M & L Cement concrete 1:4:8 ,Type D2 75 mm thick ( 40 mm graded aggregate) as in sub base

M & L Cement concrete Type B0 25 mm thick 1:2:4 ( 12.5 mm graded aggregate as in sub base

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

M & L Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes CM 1:6

M&L Rendering 10mm thick in Cm 1:4 on fair faces of brick work or concrete surfaces as in backing coat for receiving the tiles.

M & L Glazed ceramic tiles in vertical surface 450x300x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match (coloured tiles)

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match

Material & Labour for aluminium anodized snap grid frame work for false ceiling, grid size 605 x 605mm, using standard anodized aluminium 'T' section of size 45mm x25mms1.5mm thick and 45mmx25mmx1.5mm thick angle sections, etc complete all as specified & directed.

S& F Hangers 2.25mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

S& F non asbestos fibre cement building boards (E boards of size 600x600mm) decorative type fixed or laid/ inserted to timber/GI/Aluminium framework with screws as in ceiling .5mm thick.

M&L preparing newly plastered surface and Three coat of white wash on ceiling surface complete

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for hafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4

M&L RCC 1:2:4 type B-1 using 20mm graded aggr as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surface of concrete flat

M&L RCC 1:2:4 type B-1 using 20mm graded aggr as inColumns, pillars, piers, postsand struts, etc.; and mass concrete

M&L Formwork to sides pillars, posts, struts, piers, columns rough finished surface of concrete flat

M&L PCC 1:2:4 type B-0 in Damp proof course to horizontal or vertical surfaces including necessary formwork

M&L Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats ,30mm tk 2nd cl hard wood

M&L for rendering 15 mm thick in fair face of brick work or concrete surface in CM 1:6 finish even and smooth without using extra cement .

M&L for rendering 15 mm thick in other than fair face CM 1:4 finish even and smooth without using extra cement in two coats using WPC

Supply only integral waterproofing compound

M&l for preparation of newly plaster surface of wall and applying two coat of oil bound destemper over a coat of alkali resistant primer and one coat of wall putty as specified

M&l for preparation of newly plaster surface of wall and applying two coat of cement paint over a coat ofchalk whitening primer and one coat of wall putty as specified

S&F pressed steel frame for doors with one or more rebates including necessary fixing logs, hinges, log, strike plate etc. complete all as specified. Size of frame is 105X65 mm.

M & L PCC 1:3:6 Type C1 using 20 mm graded aggrege for receiving of holdfast

S&F 100mm long stainless steel butt hinges all as specified

S&F 75mm long stainless steel butt hinges all as specified

S & F Aluminium anodised, barrel tower bolts of extruded section and fixed (150 mm )

S&F Extruded aluminium alloy handles, fabricated type, anodise 150 mm long

S & F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed ( 300mm long)

Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; and similar work con- forming to Fe.290.Gde-E-165

S & F Steel windows with side hung shutters including projecting typehinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded

S&F flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

S & F Sheet glass 4 mm thich, ordinary quality and glazing with oil putty in square /Rectangular exc 0.5 sq. m in each pane

S&Fstainless steel mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples

M&LRCC 1:2:4 type b-1 20 mm graded aggr as in chajja Slabs shelves and the like including necessary form work

M&L Formwork to chullah hoods, chajjas, troughs and similar items including edges

M & L PCC 1:3:6 Type C1 ( 20 mm graded aggregate ) as in coping/Bed plate

M & L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M & L TMT bars 08 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers and binders

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough rinished surface of concrete flat.

M&LRCC 1:2:4 type b-1 20mm graded aggr as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified

M & L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete (window cill)

M & L Cement concrete Type B1 25 mm thick 1:2:4 ( 20 mm graded aggregate as in sub base window cill)

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound ,Gde -B.(plinth protection)

M&L preparation of new wooden/steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel over coat of pink primer

S & F flat iron of the 25 x 3 mm for hold fasts conforming to Fe-410 e.

M&L for point wiring concealead with suitable pvc conduit of 1.5 sqmm size single core multi stranded copper conductor unsheathed PVC insualted 1100 V grade FRLSH cable drawn into and including PVC conduit adequate width and length with accessoris and fittings like bend, elebows, crosses wall crossing etc for one light /fan point controlled by one switch including shunken type pressed steel box width 3 mm thick plastic laminated sheet top cover of approved make for housing switches, sockets outlet and regulators etc and with continuous 1 No cable 1.5 sqmm copper conductor PVC insualted, unsheathed as earth wire connected to earth dolly and to be connected boxes of suitable sizes for mounting to fittings etc, complete all as specified and as directed.

All as per item No 71 here-in -before but 1.5 sqmm copper conductor for 3 pin 5 Amps socket outlet independent (Multiple) controlled by one switch with one No earth continuity copper conductor of size 1.5 sqmm complete all as specified and as directed.

All as per item No 71 here-in -before but 2.5 sqmm copper conductor for 3 pin 15 Amps socket outlet independent (Multiple) controlled by one switch with one No earth continuity copper conductor of size 2.5 sqmm complete all as specified and as directed.

M&L switch socket combination 2 in 1 , 5 Amps multipurpose , flush type complete all as directed.

Supply and fix switch switch socket combination , 3 pin, 15/16 Amp, flash type complete all as specified and directed.

M&L for switch piano, flush type single pole one way 5 amps complete all as directed by Engr - in - charge.

M&L ceiling rose , 3 pin PVC /Polycarboante isolated body complete all as specified.

Supply and fix wall mounted fan AC single phase 230/240V, 50 Hz of size 400 mm sweep all as specified and as directed by Engr-in-charge

Job No-14FBSU/MAJ REV/03/2020-21 S& F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

S &F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

M/S SATISH KUMAR SINGH AND SONS

M/s. S. Chandra Enterprises

shashi bhushan gupta