Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹34.4 LAccepted-AOC | L1 | Accepted-AOC Being L1 | |
| 2 | L2₹35.0 L+₹18,510.30 (0.53%)Rejected-Finance | L2 | Rejected-Finance Being other than L1 | |
| 3 | L3₹40.0 L+₹5.2 L (14.9%)Rejected-Finance | L3 | Rejected-Finance Being other than L1 |
Tender Value
Refer Docs
EMD Value
₹84,000
Closing Date
14 May 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE 862 EWS
GE 862 EWS PIN 913862 c/o 56 APO
Periodical services and comprehensive repair to buildings of Zone A of AOR of AGE B/R Dett B under GE 862 EWS.
2022_MES_518526_1
GER-05/2022-23
Open Tender
Civil Works
Item Rate
180 days
GE 862 EWS
Please refer tender documents
9 documents required · 9 mandatory
₹500
GE 862 EWS
₹84,000
Yes
4 Jul 2022
18 Apr 2022
16 May 2022
18 Apr 2022
14 May 2022
2 May 2022
60 days
Amount
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and directed.
Dismantling of asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed.
Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nanital or similar pattern roof coverings complete all as specified and directed.
S&F for pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.
S&F for pre-painted galvalume aluminium zinc coated GI based plain steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, hips, valley gutters, fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.
S&F for 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with 'L' or 'J' type hooks or cranked hooks bolts and washers in roofs, walls etc with grade of zinc coating 275 gm/sqm complete all as specified and directed.
S&F for 0.80mm thick Plain galvanised mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of Zinc coating 275 gm/sqm complete all as specified and directed.
S&F for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 290 grade E-1658 complete after dismantling of old unserviceble structural steel work all as specified and directed.
S&F of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade St.-240 complete after dismantling of old unserviceble tubular truss all as specified and directed.
M&L for glazed ceramic coloured tiles of size 300x200x7mm thick, (premium quality) on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar (1:3) complete all as specified and as directed.
M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.
M&L for vitrified tiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.36 sqm but not exc 0.42 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.
M&L for dark shade vitrified tiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.42 sqm but not exc 1.0 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.
M&L for 20mm thick granite stone slab (of any type) work (table rubbed and polished) in cooking platforms, in steps, pillars, window cills, etc, laid over 15mm thick bedding in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite slab, rounding edges etc after dismantling/demolition of old unserviceable granite stone slab of any size complete all as specified and directed.
S & F for power coating of any colour (Thickness or powder coating not less than 50 micron) alumium anodized three track sliding window with two or more shutter with 4 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle lock, etc including 65 x 39.5x 1.5 mm section for complete frame and rubber beading and glazing clips etc using following sections as given in 'JINDAL' catlogue including taking down existing old window of any description complete as specified and directed by Engr-in-Charge.
M&L for Machine cut kota stone slab(mirror polished) flooring 20-25mm thick in floors and jointed with grey cement slurry mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including screed bed or bedding layer of 20 mm thick in cement mortar (1:4) after dismantling/demolition of old unserviceable kota stone of any size complete all as specified and directed.
M&L for Machine cut kota stone slab(mirror polished) flooring 20-25mm thick in skirting and dado etc and jointed with grey cement slurry mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including screed bed or bedding layer of 20 mm thick in cement mortar (1:4) after dismantling/demolition of old unserviceable kota stone of any size complete all as specified and directed.
Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.
M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius, built in cement mortar (1:6) complete all as specified and directed.
M&L for brick work using old size bricks sub class 'B', straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:4), complete all as specified and directed.
Taking down cement plaster, any description on brick or stone or cement concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.
M&L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed.
M&L for rendering 15 mm thick in cement mortar (1:4) on fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed.
M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.
M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of chalk whitening complete all as specified and directed.
Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm and n.exc 4 Sqm each and removing to store complete all as specified and directed.
Taking down chowkhats or frames (without taking off shutters from the frames) n.exc 1.5 Sqm each and removing to store complete all as specified and directed.
Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each and removing complete all as specified and directed.
S&F for pressed steel door frame of size 125x60 mm with one or more rebates incl necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats in PCC (1:3:6)type C-0 using 12.5mm graded stone agregate complete all as specified and directed.
S&F for factory made 2nd class hard wood 35 mm thick plain framed panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.
S&F for factory made 35 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed.
M&L for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square complete all as specified and directed.
M&L for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M. S . frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing mentioned in SSR Part-II 2010 complete all as specified and directed.
S&F of box type steel windows factory made with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as per IS-1038 complete all as specified and directed.
S&F of box type steel windows factory made with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded all as per IS-1038 complete all as specified and directed.
S&F for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing including powder coating n.less than 50 micron any colour etc. complete all as specified and directed.
S&F for anodised aluminium door shutters with powder coating not less than 50 micron of any colour, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, mortice lock, 1 Nos floor door stopper, anodised aluminium snap beading, screws etc. complete all as specified and directed.
S&F for anodised aluminium window and ventilator shutters with powder coating not less than 50 micron of any colour, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, aluminium anodised fittings such as peg stays 150 mm long (1 No), hinges type B-1 100mm long (2 Nos), 100mm long handle (2 Nos), anodised aluminium snap beading, screws etc complete all as specified and directed.
S&F for sheet glass 5.5 mm thick, ordinary quality and fixed with aluminum & rubber beading in square exc 0.5 sqm in each pane complete all as specified and directed.
M&L for pre laminated 12mm thick interior grade both side decorative choice lamination fixed to aluminium doors or similar works as pannel inserts complete all as specified and directed.
M&L for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Gde E-165 complete all as specified and directed.
S& F for stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples complete as in repair all as specified and directed.
S&F for 4mm thick sheet glass ordinary quality and glazing with oil putty/wooden beads in square in any size complete all as specified and directed.
M&L for plain cement concrete type B-1 , 1:2:4 ( using 20mm graded stone aggregate) as in coping, benching, hold fasts, water troughs, bed block and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete after dismantling of old unserviceble grill etc all as specified and directed.
S&F for butt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed.
S&F for aluminium anodized barrel tower bolts 150 mm long of extruded section all as specified and directed.
S&F for aluminium anodized barrel tower bolts 100 mm long of extruded section all as specified and directed.
S&F for extruded aluminium alloy handles size 125 mm fabricated type anodised complete all as specified and directed.
S&F for aluminium alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.
M&L for block boards 18/19 mm thick grade-2 interior grade commercial type fixed with screws to timber frame work complete as in repair all as specified and directed.
M&L for block boards 18/19 mm thick Grade-II interior grade commercial type with decorative face veneer on both faces, fixed with screws including 6mm thick teak wood lipping as in cup boards as in repair complete all as specified and directed.
S&F for continuous (piano) hinges, mild steel, bright finish or electro galvanised, width of flap 30mm when open as in repair complete all as specified and directed.
S&F for door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg Aluminium (extruded section) body complete as in repair all as specified and directed.
S&F for floor door stopper 140mm long of brass body and tongue, anodised, with hard drawn steel spring, fixed in floor complete as in repair all as specified and directed.
M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete as in repair all as specified and directed.
S&F for brass mortice lock vertical type 100mm long with 4 levers complete as in repair all as specfied and directed.
S&F for clean sawn second class hard wood battens for wall penelling, sectional area exc 15 Sqcm and n exc 25 Sqcm, fixed to walls at 60cm centre to centre complete after dismantling of old unserviceable wooden wall panelling all as specified and directed.
S&F for solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC/wooden frame as per specification and drawing complete after dismantling of old unserviceble PVC lining all as specified and directed.
S&F for solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC/wooden frame as per specification and drawing complete after dismantling of old unserviceble PVC lining all as specified and directed.
S&F for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to walls to make PVC frame as per specifications and drawing complete all as specified and directed.
S&F for sink with drainage board made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in CM to dwarf wall or including fixing cantilever brackets and connecting union to pipe, over all size 915mm x 460mm, bowl size 410mm x 330mmx 160mm complete as in repair all as specified and directed.
Complete removal of existing water proofing treatment over RCC roof, projections of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with wire brush including removing debris from the site and depositing in low lying area where directed and providing following :- (a) Rendering 10mm thick in CM 1:3 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing water proofing compound @ 2% by weight of cement. (b) Apply a coat of bituminous primer confirming to IS-3384@ 0.4 ltr/Sqm on newly plastered surface after curing as per IS-456 and dried. (c) After the primed surface has dried, apply a coat of hot blown bitumen(85/25 penetration) confirming to IS-702 @ 1.2 Kg/Sqm of the surface. (d) Provide polymeric water proofing membrane ISI marked laid with overlaps, bonded with hot blown bitumen, and laid by torch application method, end overlaps shall not be less than 150mm and side lap 75mm. Polymeric water proofing membrane should be five layered with centre core as 90 micron high molecular high density polyethylene film, min weight 3 Kg per sqm. APP membrane shall laid acorss the slop from lowest line of sloping roof towards ridge. (e) Over the APP membrane, apply a coat of semi hot blown 85/25 penetration grade bitumen confirming to IS-702 @ 1.20 Kg/ sqm and blinded with fine sand in dry condition @ 0.50 Kg / Sqm dusted over the bitumen coat Note : (i) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. (ii) Ponding test shall be conducted for 72 hrs as directed.
Supply only integral water proofing compound complete all as specifed and directed.
S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, double layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs including dismantling old unserviceable tank and making connections inlcuding suitable GI wash out, over flow, nipple and including 20mm bore ball brass valve with union (two nos each) screwed for iron pipe and fixed complete all as specifed and directed.
Taking up or down GI tubing 15 mm bore and connections including cleaning for refixing or removal complete all as specifed and directed.
Taking up or down GI tubing 20mm bore and connections including cleaning for refixing or removal complete all as specifed and directed.
M&L for 15 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors complete all as specified and directed.
S&F for 20 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors complete all as specified and directed.
Refixing old 15mm steel tubing and connection in new or old position(wall, ceiling, floors etc) complete all as specified and directed.
Refixing old 20mm steel tubing and connection in new or old position(wall, ceiling, floors etc) complete all as specified and directed.
M&L for bib tap cast copper alloy with crutch or butterfly handle, chromium plated, fancy type, screwed for iron pipe, suitable for 15 mm bore complete as in repair all as specified and directed.
S&F for stop valve, cast copper alloy, screwed for high pressure with crutch or butterfly handle, screwed suitable for 15mm bore iron pipe or for union both ends as in repair complete all as specified and directed.
M&L for gun metal/glove valve with iron wheel head screwed on both sides for iron pipes of 15 mm internal dia complete as in repair all as specified and directed..
S&F for 32mm dia waste coupling of brass chromium plated for glazed ware sinks, basin etc with long screwed shanks and fly nuts, flange and bedded in red lead cement mortar complete as in repair all as specified and directed.
S&F for 32mm dia waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms) complete as in repair all as specified and directed.
S&F for brass chromium plated tubular towel rail 20 mm dia "D" type 60 cm long between flange, aluminium anodised complete as in repair all as specifed and directed.
S&F for grating doom 125mm dia of PTMT (Min Weight 40 Gms) with waste hole complete as in repair all as specified and directed.
S&F for PVC connection 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore complete as in repair all as specified and directed.
S&F for 450mm long CP brass connection pipe with CP brass nuts on both ends for fixing to pipe or other fittings complete as in repair all as specified and directed.
S&F for PVC waste pipe 32/40mm bore fixed to PTMT waste coupling for kitchen sink complete as in repair all as specifed and directed.
S&F for 20 mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete as in repair all as specified and directed.
S&F for vitreous China water closet (squatt pan) Orrisa pattern 680x470 mm size pan, white, with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to flushing cistern/pipe complete as in repair all as specified and directed.
S&F for viterous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) and inlcuding set of CP jet with PVC pipe of superior quality complete as in repair all as specified and directed.
S&F for viterous china wash down water closet pan in one piece including cistern of size 73x36x74mm, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) and inlcuding set of CP jet with PVC pipe of superior quality, including CI 'P' or 'S' trap complete as in repair all as specified and directed.
S&F for PVC seat cover black/white colour or any required colour suitable for one piece WCs including PVC hinges complete as in repair all as specified and directed.
S&F for PVC low level flushing cistern 10 ltrs capacity white with inlet ball valve, float valve and handle including providing & fixing MS angle iron brackets, PVC flush pipe complete as in repair all as specified and as directed.
S&F for vitreous China wash basin, white, flat back, size 550x 400mm including 15mm bore pillar tap cast copper alloy, PVC connection 15mm length 450mm, low density PVC waste pipe complete as in repair all as specified and directed.
S&F for 15 mm bore brass CP wash hand basin mixer hot & cold water screwed down for iron pipe and fixed complete as in repair all as specified and directed.
S&F for 15mm bore brass CP sink mixer for mixing hot & cold water screwed down for iron pipe and fixed complete as in repair all as specified and directed.
S&F for 15mm bore brass chromium plated wall mixer fixed with shower rose and connecting to wall mixer complete as in repair all as specified and directed.
S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints , laid in trenchs or in floor of dia of bore 110 mm type 'B' complete after dismantling of old unserviceble PVC pipe all as specified and directed.
S&F for PVC SWR bends of 110 mm bore complete all as specified and directed.
M&L for 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in complete as in repair all as specified and directed.
M&L for preparation of new wooden surface of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.
M&L for preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.
M&L for 4mm thick designer cement fibre ceiling board in ceiling fixed with screw as per manufacturers instructions , laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 12 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturctions including dismantling of existing board etc complete all as specified and directed.
M&L for stone walling of random rubble masonry, uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar (1:6), complete all as specified and directed.
M&L for stone walling of random rubble masonry (except stones, using old unserviceable stone after cleaning), uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar (1:6), complete all as specified and directed.
M&L for rendering 20 mm thick in cement mortar (1:6) on other than fair faces of stone walls, finished even and smooth without using extra cement complete all as specified and directed.
Demolition of reinforced cement concrete in any descripation or ground floor & paving n exc 15cm thickness and removal of debris from site complete all as specified and directed.
M&L for mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
M&L for formwork to soffits of suspended slabs such as roof slabs, landings and similar work; n exc 200mm thick (Horizontal and sloping) for rough finished surface of concrete complete all as specified and directed.
M&L for RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.
M&L for 40mm thick cement concrete type B1 1:2:4 (using 20mm graded crushed stone aggregate) in floors, finishing cement concrete surface even and smooth without using extra cement complete after demolation of old cement concrete all as specified and directed.
M&L for 75mm thick PCC type C-2, 1:3:6 (using 40mm graded stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand( all by weight) complete after demolation of old cement concrete all as specified and directed.
M&L for 75mm thick PCC 1:4:8, type D-2 (using 40mm graded stone aggregates) as in sub floor, sub base for tiling complete after demolation of old cement concrete all as specified and directed.
M&L for preparation of old decorated brick/concrete plastered/un-plastered surfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of lime white wash on walls, pillars, cornices etc complete all as specified and directed.
All as per srl item No 114 above but on ceiling complete all specified and directed.
M&L for preparation of old painted wooden and wood based surfaces of any description exc 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.
M&L for preparation of old painted steel and iron surfaces of any description exc 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.
M&L for Complete removal of existing treatment on walls and applying a coat of Birla wall care putty 3mm thick and applying two coats of oil bound distemper complete all as specified and as directed by GE.
M&L for Complete removal of existing treatment on ceiling and applying a coat of Birla wall care putty 3mm thick and applying two coats of oil bound distemper complete all as specified and as directed by GE.
M&L for preparation of old decorated plastered or un plastered surfaces on walls and applying one coat of cement base paint complete all as specified and directed.
M&L for preparation of old decorated plastered or un plastered surfaces on walls and applying two coat of cement base paint complete all as specified and as directed by GE.
M&L for preparation of old wall surfaces applying two coat of exterior emulsion paint ( Appex ultima of Asian paints or its equivalent) complete all as specified and as directed by GE.
Complete removal of existing treatment of wall/roof surfaces including cornices and chajjas etc and applying two coats of exterior weather coat paint of Appex ultima of Asian paints or equivalent make in camouflage of two and more colours pattern over and including a coat of primer/putty complete all as specified and directed by Garrison Engineers.
M&L for Preparation newly plastered surface and applying two coats of exterior weather coat paint of Apex Ultima of Asian or equivalent make in camouflage of two or more colours pattern over and including a coat of primer complete all as specified and directed.
Note:- The contract sum arrived after deduction of amount of Sch of credit as listed in tender Documents.
M/S RAHUL GUPTA
MEHTA OM PARKASH
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .