REPAIR/REPLACEMENT OF BOUNDARY WALL, GATE PILLAR AND DRAINAGE AT DRONACHAL TOP AND BASE BHOPAL

Amount

Demolition of plain cement concrete of any description and in any position (below and above GL) not otherwise specifically provided complete all as specified and directed by Eng-in-charge.

Demolition of brick work/ stone masonary built in cment mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Eng-in-charge.

Demolition of reinforced cement concrete of any description and in any position (below and above GL) not otherwise specifically provided for including reinforcement cut to required size to facilitate demolition complete all as specified and directed by Eng-in-charge.

M & L for cement concrete in foundations, filling and mass concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

Use and waste type of formwork to sides of walls of RCC drain and similar works for rough finished flat surface of drain complete all as specified and directed.

Use and waste type of formwork to sides of walls of RCC drain and similar works for fair finish surface of drain complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concretewalls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished flat surface complete all as specified and directed.

Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete type B-1 1:2:4(20mm graded aggregate) nominal mix complete all as specified and directed.

M & L for Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttressesconcrete type B-1 1:2:4(20mm graded aggregate) nominal mix complete all as specified and directed.

M & L for TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Ditto as per item No 10 above above but 6mm to 8mm dia complete all as specified and directed by Eng-in-charge.

M & L for brick work with sub class 'B' bricks straight or curved on plan exc. 6m mean redius built in cement mortar 1:4 complete all as specified and directed.

M & L for uncoursed random rubble masonary built in cement mortar 1:4 complete all as specified and directed.

Ditto as above item No 13 but except stone complete all as specified and directed.

M & L for plain cement concrete in copping and haunching in drain and any other pcc course type C-1 1:3:6 type C-1 using 20mm graded stone aggregate complete all as specified and directed.

M & L for Extra for forming fair finished drain or channel 30 cm inner not exceeding girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends complete all as specified and directed.

Ditto as above sr item No 16 but for inner girth not exceeding 55cm complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Racking out joints/ pointing of cement / cement lime mortar to uncoursed randoom rubble masonary complete all as specified and directed.

M & L for 15mm thick rendering on fair finished surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M & L for keyed pointing g to random or polygonal rubble, uncoursed or brought upto course in cement mortar 1:4 complete all as specified and directed.

Dismantling posts or struts steel or R.C.C any section, including taking out embedded portion and making good disturbed ground for embedment of new fencing post complete all as specified and directed.

S&F MS angle iron posts and struts in fencing, steel gate frame including handmade hinges etc. including cutting top to shape as directed drilling holes welding and notching for wire etc and flat iron fillets for securing wire mesh including bedding or riveting etc conforming to Fe-290 Gde E-165, complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

Fixing only Chain link fencing including line wires, any mesh, size and type to any type of standerd, rails, straining bolts, etc including provision of binding wire complete all as specified and directed.

Supply only chain link MS galvanised fencing of mesh size 100 mm x 100 mm dia of wire 4mm, complete all as specified and directed.

S&F mild steel screw bolts ( machine made) with hexagonal heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washer and one hexagonal or square nut not exc 5cm and dia of shank 11 to 15mm complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description n.exc 10cm in width or girth not otherwise described including preparation of surfaces complete all as specified and directed.

S & F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

Dismantling wrought mild steel work of any description not otherwise provided for

S&F Mild Steel Framed work suck as grills, gratings, guard bar etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars complete all as specified and directed.

Jyoti enterprises

Samaksh Enterprises

anil kumar sahu

MODI CORPORATION

Vee kay construction

R K Sales

City buildcom builders & devlopers