SW Provdg Alum Partis Tough Glass railings Drg wtr sly arngt Graite Floing for Main Entr lobby Name and Sign Board Lands wrks Roof Cover AC plnts Ducts Addtl Borwell Arrants other such Ament pertit to the Ctn of Coopt Arts Sci Colge at seeval saragu

Amount

Supply, erection, and commissioning of a fully automatic water dispenser of stainless steel (SS 304) body construction with a total storage capacity of 40 liters, comprising 20 liters normal water and 20 liters cold water, complete with two taps and automatic refilling system, suitable for online connection. The unit shall have a flow rate of 100 liters per hour, operate on an AC power supply of 230 volts, and be equipped with a cold water tank made of SS 304, 0.8 mm thick. The approximate dimensions shall be 636x454x1230 mm, and the unit shall be supplied with a one-year warranty, as directed by the Departmental Officers complete complying with standard specifications.

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20 Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact- 1000 Litre Capacity

Paving the floor with best approved quality Fine Polished Steel Grey Granite Slab 1200mm x 600mm, 16mm to 18mm Thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., as directed by the Departmental Officers complete complying with standard specification.

Dadooing the walls with Ceramic Tiles of size 300mm x 600mm x 10mm thick of best approved quality laid in cement mortar 1:2 (One cement and two crushed stone sand(M-Sand)) 10mm thick and pointing with white cement using 0.40 Kg of white cement in all floors per square metre including cost of tiles, all materials, incidental charges, transportation charges and labour charges for fixing tiles neat finishing the joint flush curing as directed by the Departmental Officers complete complying with standard specification. The tiles should be got appproved by the Departmental Officers before use on work.

Supplying, Fabrication and Installation of 12mm thick Clear Toughened Glass Door along with necessary hardwares and fittings, The cost includes cost of material, labour charges, conveyance charges, fixing charges, designing charges and electricity charges and all other incidental charges., etc. The material should be got approved by the Executive Engineer before use on works.

Manufacturing, supplying and installation of glazed partiton using Vertical Stainless Steel (Grade 304) Support, 12mm thick toughened glass fixed Including Patch fittings, patch lock, other fittings, fixtures & hardware such as spider panels, glass to glass connectors etc complete, necessary holes, joints to be sealed with silicone sealant on all sides, The rate shall be inclusive of bent curved glass panels wherever the partition is curved in profile as shown in the layout plan. The material should be got approved by the Executive Engineer before use on works.

Providing and fixing 12 mm thick toughened safety glass railing (IS 2553) height 750–1100 mm, edges polished, fixed with SS 316/SS 304 fittings and necessary patch fitting (Bottom, Top and Sides) , panel gaps 3 mm sealed with silicone, including seasoned teak wood top handrail (50mm × 75mm) PU/marine varnish finish, grooved to fit glass and fixed with concealed SS screws/adhesive, complete with all accessories, alignment, cleaning, and protection. The material should be got approved by the Executive Engineer before use on works.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 50mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and laying Decorative Pressed Tiles of 12mm thick of all sizes and shapes including 25 mm cement mortar (1:4) bedding, laying with proper line, level and overlap, pointing with cement slurry, providing ridges and valleys, curing, and finishing complete as directed by the Departmental Officers complete complying with standard specification.

Supplying and fixing terracotta Gopura Clay Kalasam and finishing complete as directed by the Departmental Officers complete complying with standard specification. The material should be got approved by the Executive Engineer before use on works.

Supplying and laying of Interlocking rubber moulded hydraulic pressed paver block 83mm thick. Over a base layer of sand filling incl. Cost of materials laying and Labour charges etc., as directed by the Departmental Officers complete complying with standard specification

Supplying and fixing New Chain Link fencing in the existing available Vertical Post including cost of material and transportation to site of work (excluding cost of Vertical Post) complete complying with standard specification and as directed by the departmental officers.

Fabricating Supplying and fixing in position of Aluminium Powdered coated colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 2.70 mx 2.10 m.The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 4 mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use.

Supplying, fabricating and fixing in position of Aluminium powered coated matt finish of double leaves door with half panelled with 12mm thick bothside prelaminated partile board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section-Vertical &Top rail: 50x44.45x2.50mm @ 1.292 kg/m and Bottom rail : 100 x 44.45 x 2.50mm @ 1.974 kg /m , Lock rail : 50x44.45x2.5mm @ 1.292 kg/m,Alu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/m Alu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides),

locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 2 Nos., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 2Nos ., lock-1No., Door stopper with rubber bush including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition afterfixing etc. complete complying with standard specification and as directed by the deparmental officers.. All the Alu. sections are to be anodised with matt finish under electically contolled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge. With automatic Door Closure and hinges.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - Each., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No.,

Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete complying with standard specification and as directed by the deparmental officers. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.Without automatic Door Closure and Pivot but with hinges.

Supplying, fabrication and Fixing Structural Steel Works for following items, complete complying with standard specification. The type design for the square pipe should be got approved by the departmental officers before execution.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying Aluminum extendable ladder upto 25ft. The cost includes cost of material, labour charges, conveyance charges, fixing charges, designing charges and electricity charges and all other incidental charges., etc. The material should be got approved by the Executive Engineer before use on works.

Supplying and Fixing of Laser cut Metal works by using 3mm ms sheet for front Elevation as per the drawings and design approved by the departmental officers. The cost includes cost of material, labour charges, conveyance charges, fixing charges, designing charges and electricity charges and all other incidental charges., etc. The material should be got approved by the Executive Engineer before use on works.

Supplying and Spreading of 50mm size HBG stone jelly stone jelly for Transormer Yard including loading conveying and unloading and complete complying with standard specification and as directed by the departmental officers.

Supplying and Fixing in position of UPVC Fixed Glazing by using 4mm pinned glass, The cost includes cost of material, labour charges, conveyance charges, fixing charges, designing charges and electricity charges and all other incidental charges., etc. The material should be got approved by the Executive Engineer before use on works.

Supplying and fixing of PUF (Polyurethane Foam) insulated roofing panels for AC Plant, including necessary MS frame work and all accessories.The material should be got approved by the Executive Engineer before use on works.

Providing and fixing 10 mm thick solid Polycarbonate sheet using nessesary MS support structure from the ground. as per given technical specifications. The sheet will be mounted on hot dip galvanized steel frame work with the help of specially designed aluminum pressure pad profile and zinc coated pinhead self-drilling screw with rubber gasket for proper griping & to prevent noise leakage, and Complete complying with standard specification as directed by the departmental officer.

i)Thickness: 10 mm, solid ii) Both side UV coated iii) Weighted Sound Reduction Index Rw=34 dB iv) Light Transmittance: 92% for clear v) Tensile Strength: 60 N/m2 vi) Modulus of Elasticity: 2000 N/mm2 vii) Mechanical and Structural performance as per EN 1794 including galvanized steel work and rubber profile all around. viii) Stone Impact Resistance: As per EN 1794-1 Annex. C ix) Yellowing index shall be less than 10 as per ASTM D 1925 or equivalent x) Fire Retardant Annex A Class 2, as per EN 1794-2; Flame Spread Class 1 as per BS 476 part 7"

Providing and fixing 3D Acrylic trimcap laser cut letters (UV-resistant) with trimcap side finish. 3 years replacement warranty led and 1year replacement warranty for (SMPS) power supply. 8mm foam sheet used as base for Letters which will hold the LED's, cast acrylic letters on 4 mm ACP backing with MS frame, waterproof SMD LED back/halo lighting (IP65), concealed wiring with SMPS, complete with installation, sealing, testing, and as per approved design as directed by the departmental officer.

Supply and fixing in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand for fire fighting as per standard specifications and as directed by the Departmental Officers.

Making of lawn with mexican grass truffing including forking the ground top, dressing with sludge manure of fertilizers, mixing with the same with forked soil, watering, weeding and maintenance for a period of 90 days from the actual date of compltion and as directed by the Departmental Officers

Earth work Open excavation by Mechanical Means for Open Earthwork in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard specification and as directed by the departmental officers.

Drilling of 110mm dia vertical bore in hard rock area of any required depth as directed by the departmental Officers including labour charges for inserting casing pipes assembles in the drilled holes excuding cost of PVC casing pipes of required length including transportation charges for Rig supporting vehicles from one place to another place etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and delivery of PVC Casing pipe as per IS 12818/1992 with ISI Marking of 110mm diameter in 3m length with screwed and socket end and centering guides for every 15m length of pipe to suit deep bore wells for delivery including loading, unloading, freight, insurance etc., complete complying with standard specification.

Supplying and fixing of suitable PVC endcap (6kg/cm2)for 110mm dia borewell of best quality with ISI mark the PVC endcap should be got approved by the departmental officers before execution.

Supplying and fixing of HDPE pipe of approved quality and best variety comforming to ISI mark of the following dia size for suction pipe for compressor motor as directed by the departmental officers.

50 mm HDPE Pipe

Supplying laying and jointing CPVC Pipe (Chlorinated Poly Vinyl Chloride) (Higher pressure rating with higher pipe thickness) Standard Dimension Ratio–11 following sizes including cutting threading and fixing CPVC specials but including cost of such specials and fixing into Bore well for suction line, air pipe etc., complete complying with standard specification.

50mm CPVC Pipe

Supplying of Nylon Rope for Bore-well etc., complete as per standard specificatins and as directed by the departmental officers.

Supply of 4.00 sq.mm Copper single phase 3 core flat for submersible motor etc., complete as per standard specificatins and as directed by the departmental officers.

Supplying and fixing of 3 Phase Panel Board including labour charges etc., complete as per standard specificatins and as directed by the departmental officers.

TETRAD PROJECTS (BID ID -1559700)

SRP CONSTRUCTION COMPANY (BID ID -1561718)