Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹34.3 LAccepted-AOC FLAT NO 1 179 GANESH NAGAR S NO 10 YERAWADA PUNE 411006 | PUNE | MAHARASHTRA | 411006 | ₹34.3 L Quoted ₹34.6 L | L1 | Accepted-AOC lowest |
| 2 | L2₹41.9 L+₹7.3 L (21.2%)Rejected-Finance MOURYA HEIGHTS SATAVNAGAR HANDEWADI ROAD HADAPSAR PUNE 28 | PUNE | MAHARASHTRA | 411028 | ₹41.9 L+₹7.3 L (21.2%) | L2 | Rejected-Finance RATE HIGH |
| 3 | L3₹43.7 L+₹9.1 L (26.3%)Rejected-Finance | ₹43.7 L+₹9.1 L (26.3%) | L3 | Rejected-Finance RATE HIGH |
| Sl No | Description | Qty | Unit | Gauri Associates L2 | MONA ASSOCIATES L3 | TULSAYA CONSTRUCTION L1 |
|---|---|---|---|---|---|---|
| 1.00 | Material and labour Water proofing treatment to sunken slab, walls, etc, shall be carried out as specified below and as directed by Engineer-in-Charge.
(a) Clean the sunken portion of toilet/Baths/WCs/Kitchen thoroughly remove laitance, dirt, dust etc.
(b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar (“Dr fixit” Pidicrete URP” or equivalant).
(c) Sanitary pipes entering through walls and floor shall be sealed with “Dr Fixit Bath seal Tape” and the gaps to be grouted with non-shrink cementitous grout “Dr Fixit Bath seal Grout” orequivalant Nahani traps etc to be fitted securely and the gaps around it to be grounted in the same manner.
(d) Apply one coat of a Bitumen-modified polymer coating “Dr Fixit Bath seal Plus” or equivalant on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely. | 10 | Sqm | 1,200 ₹12,000 | 800 ₹8,000 | 250 ₹2,500 Lowest |
| 1.10(e) In the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first is dry. Extend the coating upto 150mm above the FFL. (f) After 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed 1:3:6 type B0 mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall. After satiscfactory ponding test Then fill up the sunken portion with lean concrete 1:5:10 type E2. (Note : Lean concrete 1:5:10 Type E2 shall be measured and paid separetly. (g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of approved makes such as Dr Fixit, FOSROC SIKA, MC BUCHEMIE, ROFF, etc. | ||||||
| 2.00 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for but including sunken portion and floor tiles and roof concrete , unreinforced etc complete as specified and as directed. | 24 | Cum | 260 ₹6,240 | 300 ₹7,200 | 75 ₹1,800 Lowest |
| 3.00 | M&L for PCC 1:5:10 type E2 (using 40 mm graded brick aggregate)lean concrete for filling sunken floor etc. complete as specified and as directed. | 0.5 | Cum | 4,900 ₹2,450 | 1,500 ₹750 Lowest | 2,400 ₹1,200 |
| 4.00 | M&L for cleaning the roof portion Thoroughly remove laitance diert dust ect . and form angle fillets of size 40 mm x 40 mm along the juction of wall and floor using polymer molymer modified mortar ("Dr Fixit Pidicrete URP" or Eqvt). incl 40 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded aggregate) finishing cement concrete surface even and smooth with extra cement with water proofing compound as on roof. mixing water proofing. | 250 | Sqm | 200 ₹50,000 | 50 ₹12,500 Lowest | 150 ₹37,500 |
| 5.00 | M&L for water proofing treatment by applying primer @ 0.20 kg per sqm, providing and laying 3 mm thick APP modified water proofing membrane weighing not less than 3.00 kg per sqm reinforced with non woven polyester matt weighing not less than 100 gm per sqm having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 300 N per sqm tearning strength of 100 N by torch on application including minimum over lapping 10 cm on either side and 15cm on ends and applying evenly a tack coat of hot blown bitumen grade 85/25 bottom of AAP membrane @ 1.20 Kg / sqm including two coat of solar reflective paint complete including dismantling of old unserviceable water proofing treatment / membrane and removal of debreies / dismantled materials complete all as specified and directed.
Note : (a) The water proofing treatment shall be carried out by company authorized applicator only | 350 | Sqm | 400 ₹1,40,000 | 300 ₹1,05,000 Lowest | 350 ₹1,22,500 |
| 6.00 | M&L for rendering 15 mm thick on fair faces of brick work/ concrete surface in cement mortar 1:4 with water proofing compound finished even and smooth with using extra cement at Chhajja and above wall after M&L for dubbing out 15 mm thick in cement mortar 1:4 on irrugular surface, complete all as specified and as directed.
Note:- (i) WPC shall be measured and paid sepretally.
(ii). Quoted rates shall be deemed to be inclusive of the cost of necessary scaffolding & security measures as the work has to be carried out on elvated height up to 12.0m of Building. | 85 | Sqm | 260 ₹22,100 | 50 ₹4,250 Lowest | 280 ₹23,800 |
| 7.00 | Removing of existing water tank of capacity 500, 1000 or 2000 Ltr setting aside (or lowering if required) for repair, cleaning etc and reconnecting & refixing in position after carrying out necessary roof treatment including necessary fittings and GI Pipes if required complete all as specified and as directed.
NOTE : Necessary by pass arrangements for water supply has to be done by the contractor till completion of roof work at his own cost. | 20 | Each | 500 ₹10,000 | 200 ₹4,000 | 100 ₹2,000 Lowest |
| 8.00 | Dismantiling structural steel work including doors,gates but excluding framed trusses etc complete all as specified and as directed. | 1.5 | Per Quintal | 500 ₹750 | 100 ₹150 Lowest | 200 ₹300 |
| 9.00 | S & F roof sheeting prepainted galvalume aluminium zinc coating 150 gms GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws including dismantling of old AC sheet Mangalore tiles, complete all as specified and as directed . | 250 | Sqm | 640 ₹1,60,000 | 600 ₹1,50,000 Lowest | 650 ₹1,62,500 |
Tender Value
₹49.0 L
EMD Value
₹97,960
Closing Date
25 Nov 2025, 6:00 pmClosed
GE SOUTH PUNE
NO 1 GEN BHAGAT MARG PUNE 40
8736 REPAIR TO FALSE CEILING WALL PANELLING GI SHEET MANGALORE TILES AND SURFACE RECTIFICATION IN MD AND OTM ACCN IN AOR OF GE SOUTH PUNE
2025_MES_738279_1
8736 GE SOUTH PUNE
Open Tender
Civil Works
Item Rate
180 days
GE SOUTH PUNE
AS PER TENDER DOCUMENTS
8 documents required · 8 mandatory
₹500
GE SOUTH PUNE
₹97,960
Yes
10 Feb 2026
3 Nov 2025
27 Nov 2025
3 Nov 2025
25 Nov 2025
18 Nov 2025
Amount
Material and labour Water proofing treatment to sunken slab, walls, etc, shall be carried out as specified below and as directed by Engineer-in-Charge. (a) Clean the sunken portion of toilet/Baths/WCs/Kitchen thoroughly remove laitance, dirt, dust etc. (b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar (“Dr fixit” Pidicrete URP” or equivalant). (c) Sanitary pipes entering through walls and floor shall be sealed with “Dr Fixit Bath seal Tape” and the gaps to be grouted with non-shrink cementitous grout “Dr Fixit Bath seal Grout” orequivalant Nahani traps etc to be fitted securely and the gaps around it to be grounted in the same manner. (d) Apply one coat of a Bitumen-modified polymer coating “Dr Fixit Bath seal Plus” or equivalant on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely.
(e) In the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first is dry. Extend the coating upto 150mm above the FFL. (f) After 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed 1:3:6 type B0 mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall. After satiscfactory ponding test Then fill up the sunken portion with lean concrete 1:5:10 type E2. (Note : Lean concrete 1:5:10 Type E2 shall be measured and paid separetly. (g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of approved makes such as Dr Fixit, FOSROC SIKA, MC BUCHEMIE, ROFF, etc.
Demolition of cement concrete of any description and in any position not otherwise specifically provided for but including sunken portion and floor tiles and roof concrete , unreinforced etc complete as specified and as directed.
M&L for PCC 1:5:10 type E2 (using 40 mm graded brick aggregate)lean concrete for filling sunken floor etc. complete as specified and as directed.
M&L for cleaning the roof portion Thoroughly remove laitance diert dust ect . and form angle fillets of size 40 mm x 40 mm along the juction of wall and floor using polymer molymer modified mortar ("Dr Fixit Pidicrete URP" or Eqvt). incl 40 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded aggregate) finishing cement concrete surface even and smooth with extra cement with water proofing compound as on roof. mixing water proofing.
M&L for water proofing treatment by applying primer @ 0.20 kg per sqm, providing and laying 3 mm thick APP modified water proofing membrane weighing not less than 3.00 kg per sqm reinforced with non woven polyester matt weighing not less than 100 gm per sqm having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 300 N per sqm tearning strength of 100 N by torch on application including minimum over lapping 10 cm on either side and 15cm on ends and applying evenly a tack coat of hot blown bitumen grade 85/25 bottom of AAP membrane @ 1.20 Kg / sqm including two coat of solar reflective paint complete including dismantling of old unserviceable water proofing treatment / membrane and removal of debreies / dismantled materials complete all as specified and directed. Note : (a) The water proofing treatment shall be carried out by company authorized applicator only
M&L for rendering 15 mm thick on fair faces of brick work/ concrete surface in cement mortar 1:4 with water proofing compound finished even and smooth with using extra cement at Chhajja and above wall after M&L for dubbing out 15 mm thick in cement mortar 1:4 on irrugular surface, complete all as specified and as directed. Note:- (i) WPC shall be measured and paid sepretally. (ii). Quoted rates shall be deemed to be inclusive of the cost of necessary scaffolding & security measures as the work has to be carried out on elvated height up to 12.0m of Building.
Removing of existing water tank of capacity 500, 1000 or 2000 Ltr setting aside (or lowering if required) for repair, cleaning etc and reconnecting & refixing in position after carrying out necessary roof treatment including necessary fittings and GI Pipes if required complete all as specified and as directed. NOTE : Necessary by pass arrangements for water supply has to be done by the contractor till completion of roof work at his own cost.
Dismantiling structural steel work including doors,gates but excluding framed trusses etc complete all as specified and as directed.
S & F roof sheeting prepainted galvalume aluminium zinc coating 150 gms GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws including dismantling of old AC sheet Mangalore tiles, complete all as specified and as directed .
S & F roof sheeting prepainted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified incl dismantling of old sheet complete all as specified and as directed.
S&F 1.25 mm thick Plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings incl welding and solding joint and incl dismantling old gutter (length and girth as fixed) complete all as specified and as directed.
S&F 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixing with L-type or J- type or crank hook bolt etc and incl dismantling of old sheet complete all as specified and as directed.
Dismantling and refixing old asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixing with L-type or J- type or crank hook bolt etc complete all as specified and as directed.
M&L for MS structural steel work, framed as in trusses, purlins, rafter, post etc. conforming to grade E-250 (Fe-410W, quality A) including shaped washers including necessary cutting required length, notching drilling, riveting and or welding or connecting with nut bolts with angle cleats, fish plat, gusset plate and also erecting in true position complete all as specified and as directed..
M&L for Mangalore pattern roof tiles, interlocking at side joints, laid dry including dismantling of existing complete all as specified and as directed.
M&L for dismantling and refixing old Mangalore pattern roof tiles, interlocking at side joints, laid dry complete all as specified and as directed.
M&L for Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6 including dismantling existing complete all as specified and as directed.
M&L for second class hard wood Clean sawn battens of sectional area exc 15 & n. exc 25 Sq.cm and at 25 cm centres including dismantling existing in any position complete all as specified and as directed.
M&L for disamtling and refixing second class hard wood Clean sawn battens of sectional area exc 15 & n. exc 25 Sq.cm and at 25 cm centres complete all as specified and as directed.
M&L for clean swan Second class hard-wood in scantlings including dismantling of existing in any position complete all as specified .
S&F for 20 mm thick boarding plane both side with butt joint for roof including dismantling existing complete all as specified and as directed.
S&F false ceiling with 9 to 9.5mm thick glass fibre reinforced Gypsum ceiling tiles of size 595 X 595 mm ,prima fine fissured micro look white coloured laid over including grid work 600 x 600mm using GI powder coated “T:” section grid as Main 'T' 38 X25 mm , cross 'T" 25x25mm and wall angle 25x25mm grid and 6 mm dia GI suspension wire including taking exsiting false ceiling/ lining etc complete all as specified and directed Make-Saint-Gobain, Armstrong, Diamond
M & L for removals of roots of tree growth, algae, small plants girth exc. 200cm and not exc. 600cm and applying hydrochloric acid on the left over roof portion etc and making good the existing surface with cement mortar plaster in CM 1:3 mixed with WPC @ 3% of weight of cement ,complete all as directed by Engr-in-Charge.(Note:- Quoted rates shall be deemed to be inclusive of necessary scaffolding/security measures as the work has to be carried out on elevated up to 15.0m height of Building.)
Supply and fix in replacement of followng capacity of rotational moulded polyethylene water storage tanks (vertical cylindrical with closed top) double layered, ISI marked with existing inlet, outlets & provision of washouts, vent pipe including all new tank nipples of suitable size, including dismantling old water tanks complete all as specified and directed . (a). 500 Litres
(b )1000 Litres
(c) 2000 Litres
M/L for PCC 1:2:4 type B0 (using 12.5 mm graded brick aggregate) as in coving rounded, chamfered,sub base above lean Concrete , tank stagging and other etc on sunken floor complete all as specified and as directed.
M&L for PCC 1:2:4 type B-0, 25 mm average thickness, levelling course as in padding concrete complete all as specified and as directed.
M&L for 300x300x 6 to 7mm thick, non skid, ceramic, coloured tiles, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete, laid over and including 15mm thick screed bed in CM 1:6 including demolition of existing tiles including screed bed of any description complete all as specified & directed by Engr-in-Charge.
M&L for glazed coloured digital printed ceramic tiles of size 600 mm x 300mm x 7mm thick in vertical surfaceses etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour tiles including 15 mm thick backing coat in CM (1:4) and filleting at top in same mortar incluidng taking down of existing tles & backing coat of any description etc complete all as specified and as directed.
M&L for matt finished, coloured ceramic tiles 7 to 8 mm thick 600 x 600mm size of approved colour, set, jointed in cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 20 mm thick screed bed in CM 1:6 as in flooring including demolition of existing tiles & screed bed of any description etc complete all as specified and directed.
M&L for 16 to 18 mm thick Granite slab (of any type/colour) work (table rubbed and polished) in steps, pillars;window cills/jamb, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. as counters of any radious etc laid over and incluidng 20 mm thick screed bed in CM ( 1:4) inclding demolition of existing stone slab & screed bed of any description complete all as specified and as directed.
M&L for machine cut cuddappa stone 30 to 40 mm thick one side pre-polished as in kitchen platform and partition wall of slab etc bedded & jointed in CM (1:3) including taking down existing stone slab etc complete all as specified and as directed.
S&F in repairs vitreous china wash down water closet pan, 'Pedestal' white, including fixing bolts etc including PVC seat cover white with flat bottom including MS, CP or aluminium anodised hinge devices including PVC low level flushing cistern 10 Ltr capacity with all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed.
S&F in repairs vitreous china, squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rest, including concrete bedding and PVC flushing cistern 10 Ltr capacity including all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed.
S & F in repair vitreous china wash basin white flat back of size 550 mm x 400 mm including 32 mm dia CP waste coupling long screw , chain and plug and PVC waste pipe including CI brackets, etc. complete in repairs all as specified and directed by Engineer-in-Charge
S&F in repair Automatic Sensor Glass Sliding Door (Size of shutter 800 mm x 2260 mm double) with aluminium frame complete fiitting (Unicorn) including 12 mm thick existing toughened glass shutter including 24V battry , Brush less Motor to Drive, Belt and Carriage to transmit, which can promise the smooth working and Flexibility because of its Design, it should be simple to install & program HSN /SAC 830260, complete all as directed by Engr-in-Charge.
S&F in repair Beam Sensors suitable for safety HSN/SAC 903300 of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair Motion Sensor suitable for HSN/SAC 991603 of existing make and materials complete all as directed by Engr-in-Charge.
S&F and installation of HSN/SAC 776537 complete all as specified and as directed.
S&F in repair sensor air tite sliding door ( Size 1509 mm x 2080 mm ) including Magnetic limit switch , 12 volt battery (each pair )including Servicing of motor and pair Sensor, Power supply adapter , PI sensor, in each shutter including servicing of motor etc. of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair Changing of Fuse, capacitor & micro controller (IC) for sensor sliding door of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair Motor Pulley of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair Adaptor suitable for DCB controller of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair foot sensor of sensor air tite sliding door of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair teeth belt of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair photo cell of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair Hand sensor: IR based sensor suitable for Sliding Door of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair motion sensor/ hand wave sensor for air tite Sliding Door of existing make and materials complete all as directed by Engr-in-Charge.
S&F in repair Door closer : Automatic door closer with soft closing, rated for 65 kgs, of existing size complete all as specified and as directed. Make: Apar
S&F in repair Tower Bolt : Concealed Tower Bolt, SS 304 Construction of existing size complete all as specified and as directed. Make: Apar
S&F in repair Door Handle : SS 304 Construction, length 250mm x 22mm Dia of existing size complete all as specified and as directed. Make: Apar
S&F in repair Drop seal : Automatic drop seal, Size as per length of door of existing size complete all as specified and as directed. Make: WIESPL
S&F in repair Gaskets : Rubber Gaskets for an airtight seal of existing size complete all as specified and as directed. Make: WIESPL
S&F in repair Door lock: Concealed door lock, SS 304 finish of existing size complete all as specified and as directed. Make: Apar
S&F in repair Sensor: IR based sensor for hands free tap activation of existing size complete all as specified and as directed. Make: WIESPL
S&F in repair foot paddle: SS 304 construction, manual activation of tap of existing size complete all as specified and as directed.
S&F in repair Soap dispenser, Manual Soap Dispenser, SS 304 construction of existing size complete all as specified and as directed. Make: WIESPL
S& F in repair Auto SS304 tap: SS 304 Finish, Automatic Tap, of existing make and materials complete all as directed by Engr-in-Charge. Make- Jaquar.
M&L for providing and fixing CP toilet fitting in repairs complete as specified and as directed by the Engr -in-Charge for the following:- (a). Bib taps CP 15mm bore fancy type with wall flange conforming to CAT No. CON- 037 Jaquar/ 9206 (CASA) of Prayag complete all as specified and as directed.
(b). Soap dish CAT No. ACN-1131N Jaquar/BA-259 of Prayag complete all as specified and as directed.
(c). CP towel rail 20mm dia and 600mm long including brackets conforming to CAT No. ACN-111N of Jaquar/ BA-20 of Prayag complete all as specified and as directed.
(d). Health faucet CAT No. ALD-583KN of Jaquar/ BEA-85 of Prayag complete all as specified and as directed.
(e). Angular type stop cock conforming to CAT No. 053 of Jaquar/ 9210 of Prayag complete all as specified and as directed.
(f). CP toilet paper holder conforming to CAT No. ACN-1151N of Jaquar/ BA-38 of Prayag complete all as specified and as directed.
(g). CP towel ring round with round flange conforming to CAT No ACN-1121 BN of Jaquar/9218 of Prayag. complete all as specified and as directed.
(h). CP wall mixer 3 in 1 including telephone shower for 15mm bore of pipe conforming to CAT No.CON 281 and HSH -1939 of Jaquar/ PIS-70 and BH-73 of Prayag complete all as specified and as directed.
(j). 2 way bib cock with wall flange conforming to CAT No. CON 041N of Jaquar complete all as specified and as directed.
(k). Towel Rack 600 mm long with lower hangers stainless steel conforming to CAT No. AEC - 1181N of Jaquar complete all as specified and as directed.
(l). Brass chromium plated shower rose 100 dia with 235 mm long arm with or without swivel joints, including fixing to steel pipe or union Jaquar" all as specified and directed by Engr-in-Charge
(m). Pillar taps long neck with aerator CAT No CON -021KN screwed for iron pipe and fixed complete all as specified and as directed.
S&F in repairs satinless steel Robe Hook (khuti) with 5 Hook complete all as specified and as directed.
S&F in repair Sink Cock with swinging casted spout with aerator conforming to CAT No. SQN - 522KN of Jaquar complete all as specified and as directed.
S&F in repairs glass corner assembly consisting of 5.5 mm thick sheet glass round (9" x 9" ) with stainless steel railing complete all as specified and as directed.
S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.
S&F 100 mm round Stainless steel Grating with waste hole complete all as specified and as directed.
S&F 100 mm round Stainless steel Grating complete all as specified and as directed.
S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm suitable for hot and cold water, complete all as specified and directed.
S & F in repairs PVC flexible waste pipe 32mm bore complete all as specified and as directed.
M&L for old size fly ash bricks, straight or curved on plan exceeding 6 m mean radius built in CM 1:6, including demolition of brick / stone wall etc complete all as specified and as directed.
S&F in repairs 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall / ceiling or laid in trenches including taking down of old existing pipe complete all as specified and as directed. Note for item nos. 81 & 82: - Quoted rates shall be deemed to be inclusive of necessary scaffolding / security measures as the work has to be carried out for elevated up to 15.0m height of Building.
S&F in repairs 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall / ceiling or laid in trenches including taking down of old existing pipe complete all as specified and as directed.
S&F in repairs PVC (SWR) bends any radius 110 mm bore complete all as specified and as directed.
S&F in repairs PVC (SWR) bends any radius 75 mm bore complete all as specified and as directed.
S&F PVC (SWR) vent cowl 100 mm bore complete all as specified and as directed.
S&F PVC SWR branch piece, (Double 'Y') equal or unequal of 110 mm bore complete all as specified and as directed.
S&F PVC SWR branch piece, (Double 'Y') equal or unequal of 75 mm bore complete all as specified and as directed.
M&L in replacement for PVC (SWR) gully trap 125/100mm, setting and jointing with solvent cement complete all as specified and as directed.
M & L in replacement PVC (SWR) floor trap, dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.
M&L for 110mm PVC (SWR) WC connector with lip ring complete all as specified and as directed.
M&L for 75 mm PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and as directed.
S&F 40 mm bore Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm complete fittings all as specified and directed .
Re-fixing of old serviceable steel tubing and connections in new or old position (wall/floor/ ceilings etc) of following sizes including fitting and fixtures including taking down of old existing pipe, complete all as specified and directed:- (a) 15 mm bore
(b) 20 mm bore
S&F GI tubing "medium grade" galvanized including with all fittings and fixtures, fixed to walls or ceiling or laid in floors etc. including taking down of old existing steel tubing of following sizes complete all as specified and directed:- (a) 15 mm bore
(b) 20 mm bore
(c) 25 mm bore
M&L for cutting of existing steel tubing and including screwing for alterations or additions for following size complete all as specified and directed:- (a) 15 mm bore
(b) 20 mm bore
(c) 25/32 mm bore
S & F in repairs gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of following sizes complete all as specified and directed:- (a) 15 mm bore
(b) 20 mm bore
(c) 25 mm bore
S&F in repairs ball valves suitable for iron pipe high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed of following sizes complete all as specified and directed:- (a) 15 mm bore
(b) 20 mm bore
(c) 25/32 mm bore
S&F 20mm bore ball valves suitable for iron pipe high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed complete all as specified and directed.
M&L for cutting in stone wall for chases, pining in making good to facings where required and painting in cement mortar 1:3 to ends or edges of landinsgs, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed watter tubing etc and making good , cutting not exc10cm girth complete as specified and directed.
M & L for Cleaning and removing all dirt and scale etc from tank and from the mouths of circulating pipes for the tanks of following capacity including written of date of cleaning with synthetic enamel paint complete all as specified and as directed for the following :- (a) Not exc. 500 Ltrs
(b) Not exc. 1000 Ltrs
(c) Not exc. 2000 Ltrs
S&F, in repairs, PVC water storage tank lid/ cover of 500/1000 litres Capacity fixed with PVC locking arrangements complete all as specified and as directed.
Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.
M&L for rendering 15 mm thick in cement mortar 1:4 with water proofing compound finished even and smooth without using extra cement after including M&L for dubbing out average 15 mm thick in cement mortar 1:6 on irregular face of wall, complete all as specified and as directed. Note:- WPC shall measured and paid sepretally
M&L for rendering 15 mm thick in cement mortar 1:6 finished even and smooth without using extra cement after including M&L for dubbing out average 15 mm thick in cement mortar 1:6 on irregular face of wall complete all as specified and as directed.
M&L for rendering 10 mm thick in cement mortar 1:4 in ceiling and finished even and smooth with using extra cement after including M&Lfor dubbing out average 15 mm thick in cement mortar 1:4 on irregular face of ceiling complete all as specified and as directed. Note:- Plaster work has to be carried out on ceiling as in patches and no extra payment shall be consider on this account.
M&L for rendering 15 mm thick on fair faces of brick work in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.
M&L for rendering 15 mm thick on fair faces of brick work in cement mortar 1:4 with water proofing compound finished even and smooth without using extra cement complete all as specified and as directed. Note:- WPC shall measured and paid sepretally
M&L for rendering 15 mm thick on fair faces of brick work/ concrete surface in cement mortar 1:4 with water proofing compound finished even and smooth with using extra cement at Chhajja and above wall after including M&L for dubbing out 15 mm thick in cment mortar 1:4 on irrugular surface complete all as specified and as directed. Note:- (i). WPC shall measured and paid sepretally (ii). Quoted rates shall be deemed to be inclusive of necessary scaffolding / security measures as the work has to be carried out for elvated up to 12.0m height of Building
Supply only Integral waterproofing compound complete all as specified and as directed.
M&L for preparatio of new plastered surface of wall and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.Over and including 2 mm thick wall care putty over plastered surface to prepare the surface even and smooth complete all as specified and as directed.
M&L for preparation of new surface of ceiling and applying 2 coats of oil bound distemper over and including 2 mm thick wall care putty complete all as specified and as directed.
M & L for preparation of surface of any description new plastered, over 10 cm width or girth including and applying two coats of exterior weather proof paint complete all as specified and as directed.
M&L for preparation of old decorative surfaces of wall incl, cornices (plastered or unplastered) of any description, sand papered and dusted including complete removal of existing surface of wall and applying two coats of Oil Bound distemper over and including coat of 2mm thck wall care putty complete all as specified and directed
M&L cement concrete type B0 1:2:4 using (12.5 mm graded aggregate) , as in roof kerbs , rounded chamfered on edges , in lintel upto 1.5 m clear span, cill, steps, seismic and other similar bands, plinth courses string courses, lacing courses , copings kneelers, apex including weathering , slightly rounded or chemfered angles and throating etc. necessary form work including demolation of existing concrete all complete as specified and as directed.
M&L for 75 mm thick Cement concrete type C1, 1:3:6 (using 20 mm graded aggregate) as in flooring/ Plinth protection Finish even & smooth with extra cement complete including demolition of existing concrete complete all as specified and as directed.
Removing debries of demolition building materials etc. (other than spoil payable under respective items to a distance of exceeding 5 Km, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and as directed.
M &L for preparation of new steel surface & applying two coats of synthetic enamel to steel surface of any description over 10 cm in width or girth not otherwise described over a coat of red oxide primer complete all as specified and as directed.
M&L for preparation of old painted wooden surfaces exe 10 cm width or girth and applying one coat of synthetic enamel paint complete as specified and as directed.
S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers , and wastes coupling , including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, bowl size 560 mm x 460 mm including coupling complete as specified and as directed.
Taking down chowkats or frames wooden/steel with shutters (w/o taking off shutters from frames) n.exc 1.5 Sqm each complete as specified and as directed.
Taking down /cutting steel windows shutter by means of gas cutter with out disturbing of sofit / jambs / cills etc of any description n. exc. 1.5 sqm complete all as specified and as directed.
S&F aluminium powder coated three track sliding window with two or more shutters with & including 4 mm thick tinted glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle, lock etc using PVC beading etc using following sections of `Jindal Aluminum Ltd ' or equivalent in Ajit India Pvt Ltd or Crystal Bombay, as approved. fixing to stone masonary walls with & including Ist class teak wood plugs of size 20mmX20mm at an interval of 0.5m alround the track including drilling holes. (a) Frame bottom 20620 (b) Frame top & side 20621 (c) Shutters top & bottom 20844 (d) Shutter inter lock 20724 e) Handle (Side ) for 20606 shutter
S&F aluminium powder coated ventilators/louvers 5mm thick x10cm wide frosted glass strips and following aluminium powder coated sec conforming to catalogue of JINDAl or of equivalent make and rubber beading etc all as directed :- (a) SP - 20048 (b) Glazing clips 19352
S & F solid PVC door frame of size 50 mmx47mm made out of 5 mm plain colour PVC sheet rainforced with MS tube suppling and fixing in opening complete all as per specification and drgs complete as specified and as directed.
S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles plain colour PVC sheet for top rail , lock rail & bottom rail either side & as gap isert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC beading and jointed together with solvent cement ,suppling and fixing in the frame at site as per SSR Pt-I specification & drawing
Supply and Fixing in repair of solid wall lining consisting of 5 mm thick , plain coloured or wood grain printed or as approved by the Engr-in-Charge / prelam PVC sheet used inclusive of solvent as per specification of manufacture including dismantling of existing boarding (Make:- Rajshri / Duroplust ).
Supply and Fixing in repair of 5 mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing as in grid / frame on wall for wall lining/paneling as per specification of manufacture) as directed by the Engineer-in-Charge
M&L for 6 mm thick (consisting of no of 6 ply) Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with screws to timber frame work including two or more coat french polishing and dismantling of existing boarding complete as specified and as directed.
M&L 2nd class hard wood Plain fillets sec area exc 6 Sqcm but n.exc 13 Sqcm square, rectangular or triangular in section, clean sawn, secured with nails or brads complete as specified and as directed.
M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as directed by Engr - in - Charge .
M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works with one or more coats complete all as directed by Engr - in - Charge .
S&F 200mm size Aluminium Anodised barrel tower bolt of extruded section complete as specified and as directed.
S&F 100mm size Steel butt hinges ,medium weight, cold rolled complete as specified and as directed.
S&F 150 mm Aluminium Anodised handle, fabricated type complete as specified and as directed.
M&L Preparation of Old painted Steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coats of Synthetic enamel paint complete all as specified and directed
Supply and fix galvanized corrugated mild steel sheeting with two corrugation side lap, fixed with coach screw and washer in roofs wall etc with grade of zinc coating 275 including dismantling of old AC sheet all as specified and directed by Engr-in-Charge.
M & L for re-fixing of existing ridge or hip tiles to suit Mangalore pattern of roof tiles, bedded as jointed in CM 1:6 including dismantling of existing Mangalore tiles all as specified and directed by Engr-in-Charge.
M&L for 50 micron frosted privacy glass film type fixing in existing aluminium window glass all specified and directed by Engr-in-Charge
Repair /grouting to mouth of 110 mm rain water pipe (any type) of roof with cement including cleaning of existing pipe complete all as directed by Engr-in-Charge. Quoted rates shall be deemed to be inclusive of necessary scaffolding / security measures as the work has to be carried out for elvated up to 12.0m height of Building
Gauri Associates (BID ID -3493210)
MONA ASSOCIATES (BID ID -3490404)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.60 MB
8736TD.pdf
Tender Documents • 0.97 MB
BOQ_826663.xls
BOQ • 0.81 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .