SPECIAL REPAIRS TO BLDG No. T 1 MALE HOSPITAL WARD AT MH, SPECIAL REPAIRS TO WORKSHOP BLDG No. E 4 FOR INSTALLATIONS AT MT YARD AND PROVISION OF CERTAIN OTHER WORKS UNDER GE BELGAUM

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of plain cement concrete of any description and in any position not other wise specifically provided for all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar or lime cement mortar including all quoins, arches, pillars, etc. but excluding precast concrete articles, in any position below or above ground level all as specified and directed.

Cutting into old masonry built in cement motar to form toothings for and bonding in new brick or stone work including making good in cement mortar

Dismantling timber scantlings 40 sq.cm and over in section, in any position, in un-framed work all as specified and directed.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Taking down shutters of any description area not exc 1 sqm each all as specified and directed.

Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise provided for all as specified and directed.

Dismantling of corrugated or semicorrugated Asbestos Cement sheets in roof coverings including ridges, valley gutters, etc. all as specififed and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Dismantling wall or ceiling boards or insulation boards/ slabs of any thickness including cover fillets all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/dense soil all as specified and directed.

Returning filling in including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread, levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L for plain cement concrete 1:4:8 type D2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L for plain cement concrete 1:3:6 type C2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10cm width, blocks cast in PCC 1:3:6 type C1, using 20mm graded stone aggregate, set in CM 1:6 complete all as specified and directed.

M&L plain cement concrete 1:2:4, type B0, using 12.5mm graded stone aggregate as in coping, bed blocks, benching in channels, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in coping, bed blocks, benching in channels, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for extra for forming fair finished drain or channel of 45cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B1, using 20 mm graded stone aggregate as in cover slabs, etc. set in CM 1:6 all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate in beams, cantilevers, lintels, lintel bands all as specified and directed.

Supply only approved integral water proofing compound all as specified and as directed.

M&L for use of form work to sides and soffits of roof beams, tie beams, lintels, and similar works for rough finished flat concrete surfaces all as specified and directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work all as specified and directed.

Fixing only serviceable timber scantling of any description obtained from dismantling in un-framed work all as specified and directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for powder coated aluminium frame work as in doors, partitions and windows using standard aluminium extruded sections with thickness of powder coating not less than 50 microns including provision of glazing clips, hinges, handles, etc all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels shall be measured and paid separately.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on single side reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F SS butt hinges 100mm in size medium weight all as specified and directed.

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F aluminium anodised barrel tower bolt 100mm size all as specified and directed.

S&F aluminium handle, 'D' type, anodised 150 mm in size all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire & average width of aperture 1.18mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

M&L for mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No. 45 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

S&F rolled mild steel posts and struts in fencing and similar work conforming to Fe-290 Gde E-165 including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets for securing wire mesh etc. all as specified and as directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 30cm long and 11 to 15mm dia neck all as specified and as directed

M&L for mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates complete all as specified and as directed.

S&F mild steel works in tubular trusses, posts, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 all as specified and as directed.

M&L for mild steel flats for wind ties for roof including securing bolts and similar works, conforming to Fe-290 Gde E-165 all as specified and as directed.

M&L for mild steel small articles like hold fasts, bands, straps, including bolts, if required; hooks (stay), hook and pintle hinges and similar articles conforming to Fe-290 Gde-E-165 all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roof covering/ claddings to wall, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S&F PVC (SWR) eaves gutter half rounded 150mm bore including pipe accessories PVC holder bats bolts nuts etc. including taking down existing unserviceable gutters of any description and size and making good disurbed surfaces all as specified and directed.

M&L for 4mm thick Aluminium Composite Panel comprising of a core containing not less than 70% non combustible mineral filling sandwiched between two skins of 0.5mm thick aluminium alloy PERALUMAN-100 (AlMg1-NS41) complete with all necessary sub-structures, anchors, hardware and fittings to provide a total installation, fixed to existing wooden/ steel members all as per manufacturers instructions, all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc. Make: Alstrong/ Aludecor/ Alucobond/ Eurobond

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminum anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 50mm thick plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in sub base for floors/ drains all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring all as specified and directed.

M&L for coloured vitrified tiles, square or rectangular, light shade, 10mm thick, area of each tile exc 0.36sqm but not exc 0.42 Sqm, as in flooring, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured vitrified tiles, square or rectangular, light shade, 10mm thick, area of each tile exc 0.36sqm but not exc 0.42 Sqm, on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 6 to 7mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for coloured glazed ceramic tiles 300mm x 450m size, 7 to 8mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, set and jointed with neat cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab laid over 20mm thick screed bed in cement mortar 1:4 including rubbing and polishing complete all as specified and as directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for coloured polished designer cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for 55-60mm thick machine pressed precast concrete interlocking coloured paver blocks, M-35 grade, any shape and size with glossy finish on top confirming to IS 15658-2006 all as specified and directed.

M&L for crushed stone sand (M-sand/ Robo sand/ i- sand) cushioning under interlocking paver blocks including watering and consolidation complete all as specified and as directed.

M&L for plain cement concrete 1:3:6, type C1, using 20 mm graded stone aggregate, 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or block masonry or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or block masonry or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for 4mm thick sheet glass ordinary quality and glazing to aluminium joineries in square n. exc 0.5 sqm in each pane all as specified and directed.

M&L for three coats of white wash on newly plastered walls, pilasters, cornices, etc. including necessary preparation of surfaces all as specified and directed.

M&L for three coats of white wash on walls, pilasters, cornices, etc. including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper any colour, over a coat of primer over 1mm thick layer of wall care putty, on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior emulsion paint over a coat of primer on newly plastered surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for preparation of old wooden surfaces of any discription over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of new steel surfaces not exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

S&F 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 15 mm bore Bib tap, long body, brass chromium plated, fancy type with wall flange, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F 15mm bore stop valves, brass chromium plated, fancy type, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F pillar taps, brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Cat No. 563 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F vitreous china wash basin, white, size 550x400mm, including CI brackets and cutting for and pinning in ends of brackets or erecting stands etc. all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, fixing bolts, etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F PVC flexible pipe (waste pipe), suitable for 32 mm bore waste coupling of sink/ wash hand basin/ urinal all as specified and directed.

S&F brass chromium plated tubular towel rail 600mm long with and including Chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed, in any length, with solvent cement joints, laid trenches or in floors, all as specified and directed.

M&L for bed concrete to 110mm bore drain pipes in Plain Cement Concrete 1:4:8 type D2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

S&F PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, 110mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required all s specified and as directed.

Taking down carefully point wiring of any description complete for light, fan, 5 A socket, 15 Amps socket, 2 way points and bell point etc including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, holders, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 Sq mm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 2nd class HW board fixed on wall with sunmica top for mounting switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed.

All as described in item No. 103 but for one ceiling fan/ wall monting fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 103 but for one bell point controlled by one bell push

All as described in item No. 103 but for one 05 Amps socket outlet on independent board.

All as described in item No. 103 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 103 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F switch, piano type, 5 Amps, flush button, 230 volts, AC, one way all as specified and directed.

S&F switch, piano type, 15 Amps, flush button, 230 volts, AC, all as specified and directed.

S&F bell push, flush type, 5 Amps, 230 volts, AC, one way all as specified and directed.

S&F socket outlet 5 Amps 2 cum 3 pin flush type multipurpose all as specified and directed.

S&F socket outlet 15 Amps, 3 pin 5 Amps cum 3 pin 15 Amps, flush type multipurpose all as specified and directed.

S&F fan regulator electronic step type suitable for 1200/1400 mm sweep ceiling fan all as specified and directed.

S&F ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 20W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 1x 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 10W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F 42 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 42 W high brightness SMD LEDs for glare free homogenous illumination, including electronic driver etc. complete with all accessories internally pre wired including cutting of false ceiling sheet to required size and fixing aluminium strip as per the existing size in false ceiling for fixing of light fitting and providing aluminium strip supports as reqd and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2x2 or equivalent in CG/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP66 protection, 6000K and impact resistance IK07, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F in repairs Single pole and neutral enclosure, powder coated, with a two pin earth plug and socket complete, 20 Amps, 240V, including provision of one single pole MCB 20 Amps 'C' curve type all as specified and as directed.

S&F in repairs, MCCB VTPN DB 4 Way, vertical type, suitable for MCCB as incomer 415 volts rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCCB DB on board complete all as specified and directed.

S&F in repairs, MCB DB SPN 12 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs MCCB FP 125 Amps ,25KA, 415 Volts, AC supply, fixed thermal magnetic settings, all as specified and as directed.

S&F MCB DP 63A 'C' series 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F wall mounting fan, 230 volts, single phase, 300mm sweep, with all accessories complete including provision of suitable clamps for fixing to wall and making good disturbed surfaces matching with the existing surface complete all as specified and as directed. Make: HAVELLS Model No. D'zire or equivalent model in makes Crompton Greaves/ USHA

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, 3 blades, with all accessories complete including taking down existing unserviceable ceiling fan of any description and size from the location and setting aside for fixing/depositing to MES E/M store all as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in Crompton Greaves/ USHA

S&F storage type water heater (Geyser), vertical type, 50 litres capacity, 2000/1500 Watts, Star rating including drilling holes into wall, provision of 4 Nos of suitable size anchor bolts, nuts and washers, connecting up electrical & water supply lines, testing including taking down existing unserviceable water heater of any description and capacity and depositing to MES E/M store all as specified and as directed.complete all as specified and as directed. Make: MONZA EC model of HAVELLS or equivalent model in RACOLD/ BAJAJ

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

SHRI.H.R.PATIL

ASHOK M RAJGOLKAR

M/s. J P CONSTRUCTIONS

M/s. N D KALING

M/s B C CHOUGULE

RAJENDRA KRISHNA SARAF

SAMARTH ASSOCIATES

M/S MAHADEV M PATIL