Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹29.3 LAccepted-AOC KOT KHALSA ROAD AMRITSAR | AMRITSAR | AMRITSAR | PUNJAB | ₹29.3 L | L1 | Accepted-AOC L1 |
| 2 | L2₹30.1 LRejected-AOC | ₹30.1 L | L2 | Rejected-AOC L2 |
| 3 | L3₹32.8 LRejected-AOC | ₹32.8 L | L3 | Rejected-AOC L3 |
Tender Value
₹36.4 L
EMD Value
₹72,793
Closing Date
25 Feb 2026, 5:00 pmClosed
EE_ConstructionDivisionNo1PWD_TarnTaran_atAmritsar
EE_ConstructionDivisionNo1PWD_TarnTaran_atAmritsar
Repair and Renovation of Polyclinic at District Tarn Taran
2026_CEPW_159931_1
29/3 dt. 09.02.2026
Open Tender
Civil Works - Buildings
120 days
Polyclinic at Tarn Taran
Please refer Tender documents.
11 documents required · 11 mandatory
₹5,000
₹72,793
9 Mar 2026
11 Feb 2026
26 Feb 2026
11 Feb 2026
25 Feb 2026
11 Feb 2026
Civil Work
Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade
Scraping of white wash from walls
Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish
20mm Cement plaster 1:4 to brick work
Finishing walls with Premium Acrylic smooth exterior paint with silicon additives of required shade with two or more coats applied @ 1.43litre/10 Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm
Painting two or more coats with synthetic enamel paints in all shades on old wood work or metallic or plastered or concrete surface to give an even shade including rubbing down old paint
Supplying Pressed steel sheet frames (chowkhat) consisting of 18gauge (1.25 mm thick steel sheet of the specified section, including iron lugs (hold fast) iron hinges conforming to PWD specification including bolts for fixing stops lock notch provision for receiving tower bolts and finished with 1 primer coat approved quality, fixed in position excluding the cost of cement concrete 1:3:6 for fillings in the frame and cement concrete 1:2:4 for lugs complete
Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position 35mm
Providing & fixing 4" stainless steel handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge.
Providingand fixing bright finished brass door latch with necessary screws etc. complete : 250x16x5 mm
Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt)
Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete .S.I Designation No. II (size of door 701mm to 850mm)
Providing & Fixing glass panes with nails and putty or wooden strip complete in all respect Glazing area above 0.09 sqm 4mm thick or 10.78 Kg/ sqm
Providingand fixing1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approvedmake in all colours, shadesexcept burgundy, bottlegreen, blackof size200x300mm, 100x200mm, 200x200mm as approved by Engineer-in-Charge in skirting, risersof steps and dados over 12mm thick bed ofcementMortar1:4(1cement:4 finesand)and [email protected] including pointing inwhite cement mixed with pigment of matching shade complete.
Dismantling of wall tiles at any floor of the building, laid in cement mortar including scraping of cement plaster and disposal of malba at a suitable place with in a distance of 100 Mtrs of the complex complete in all respect
Regrading terracing of mud plaster covered with tiles or bricks in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud plaster to proper, slope, relaying mud plaster Gobri leaping and tiles or bricks grouted in cement mortar 1:3 (1cement and 3 fine sand) including replacing unserviceable tiles, or bricks with new over and disposal of unserviceable material to the dumping ground within 50 m lead (The cost of new tiles or bricks excluded)
Cost of new tiles to be replaced instead of broken tiles in regrading.
Providing and fixing of 30mm thick factory made Polyvinyl Chloride (PVC) door shutter (without chowkhat) made of styles and rails of a UPVC Plug profile section of size 30mm x 60mm and wall thickness 2mm ±0.2mm with inbuilt decorative molding edging on one side. The styles and rails with plastic brackets of size 75x220mm meter and welded at the corners. The- stiles of the shutter reinforced by inserting galvanized MS tube of size 25x20mm and 1mm ± 0.1mm wall thickness. The lock rail made up of ‘H’ section, a UPVC Plug profile section of size 30mm x 100mm and 2mm±0.2mm wall thickness welded to the shutter style with a UPVC Plug profile section single panel of size not less than 620mm, having overall thickness of 20 mm and 1 mm±0.1 mm wall thickness with 20 mm panel beading of suitable size /Glass(4mm thick plain glass)/louver section, louver frame of suitable size, as per manufactures specification and direction of Engineering charge. (For WC and bathroom door Shutter)
Providing and laying vitrified floor tiles in different sizes in light colour shades made using Full Body Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Full body vitrified tiles have pigment in entire body / thickness of tile which makes chips and scratches less noticeable and make na ideal choice for high traffic zones.). Size 600x600 mm
Dismantling brick or flagged stone flooring including concrete base
Dismantling brick work tile, masonry or tile lining In cement
Coloured Granite stone tiles 15mm to 20mm thick in skirting, risers of steps, dado walls and pillars laid in 12.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour for fixing dowel pins and cramps
Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position
Providing and Fixing 10-12mm thickness charcoal louver sheet complete with all respect.
Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.
Reinforced cement concrete M-20 mechanically batchmixed using batch type concretemixer asper IS:1791andvibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth.
Cold twisted deformed (ribbed/ tor steel) Bars Fe 500 grade as per IS 1786-2009 for R.C.C. works, where not included in the complete rate of R.C.C. including bending, binding, and placing in position complete.
First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level..
12.5 mm thick cement plaster 1:4
20mm thick cement plaster 1:4 in two coat work
Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.
Providing and fixing 110 mm dia . U.P.V.C Rain water pipe of 4 kgf./sqm as per IS:4985 including jointing during masonary complete as per specifications and to the entire satisfaction of Engineer-in- charge.
Providing and fixing 110 mm dia. U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. UPVC 110 mm bend
Providing and fixing 110 mm dia. U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. UPVC 110 mm Coupling /Sockets
Electrical Services
RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES:
Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):-
Wiring fan point (With fan box)
Wiring light point
Wiring 6Amp. wall socket point
Wiring 6Amp. Plug control comprising wall socket point
Wiring 16/20Amp. power plug control point
RECESSED AIR CONDITIONER SUPPLY TERMINAL POINT (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES):
Wiring air conditioner supply terminal point recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 25Amp. combined/ universal Socket (shuttered) and modular motor starter 25Amp. (2Module), covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):
Wiring AC supply terminal point having 1No. 25Amp. universal Socket (shuttered) erected at AC height and 1No. Motor starter 25Amp. erected at switchboard heigh
RECESSED COMPUTER SUPPLY TERMINAL POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES):
Wiring Computer supply terminal points recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10/16/20Amp. Switches and blanking plate etc., and covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):-
Wiring Computer terminal point having 3 Nos. 6Amp. 2/3 universal socket (shuttered), 1No. 16/20Amp. universal Socket (shuttered), 2Nos. 16/20Amp. switch with indicator and 2Nos. blanking plate (Modular accessories).
PVC INSULATED PVC SHEATHED FR ROUND FLEXIBLE COPPER CONDUCTOR CABLE:
Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:
Overall size 1.5sq.mm (Un-sheathed) (Basic Rate Rs,18/- +60%prem.+5.35%)
Overall size 2.5sq.mm (Un-sheathed) (Basic Rate Rs,27/- +60%prem.+5.35%)
Overall size 4sq.mm (Un-sheathed) (Basic Rate Rs,39/- +60%prem.+5.35%)
Overall size 6sq.mm (Un-sheathed) (Basic Rate Rs.54/- +60%prem.+5.35%)
Overall size 10sq.mm (Un-sheathed)(Basic Rate Rs.88/- +90%prem.+5.35%)
Copper Earthing
8 SWG CCOPPER EARTHING
Earthing with 8 SWG (4mm dia.) electrolytic copper wire thimbled (1No. copper thimble with suitable size steel bolt, washers & double nut) with 30cm x 60cm x 2mm thick copper plate (made cylindrical) burried below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) recessed in wall and in floor etc., up to suitable Length in metre (including bore Length). G.I. pipe 20mm dia. (A-class) of suitable Length should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-
Earthing with 8 SWG (4mm dia.) copper wire thimbled with 30cm x 60cm x 2mm thick copper plate burried 4.50 metre (14.76 feet) below ground level (up to 8metre in Length) with G.I. pipe 20mm dia. (A-class), 3metre long
(A) MINIATURE CIRCUIT BREAKERS:
Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:-
MCB Single Pole 6-32amp. (10kA, Curve-C) (Basic Rate Rs.134/- +50%prem.+5.35%)
MCB Double Pole 50, 63amp. (10kA, CurveC) (Basic Rate Rs.321/- +50%prem.+5.35%)
SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB's/ RCBO's/ RCCB's:
Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, colorcoded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:-
SP&N Double Door Distribution Board 12 way each
XLPE INSULATED UN-ARMOURED CABLES (ON SURFACE):
Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:-
Overall size 16sq.mm (2Core) Un-armoured (On-Surface) (Basic Rate Rs.82/- +90%prem.+5.35%)
SHEET METAL BUS BAR CHAMBERS (COPPER STRIPS):
Supply and erection of sheet metal busbar chamber (factory fabricated) duly powder coated on existing surface with required 4Nos. of tin plated copper busbar strips of suitable length and crosssectional area mounted on DMC/ SMC moulds at sufficient distance, enclosure made of M.S. sheet 1.6mm thick with hinged cover and lock, fitted with dust excluding gaskets and secured with sufficient no. of cadmium plated iron screws and of given overall dimensions and to be fixed with G.I. bolts and nuts/ rag bolts and nuts etc. complete with all accessories including connections with suitable size of thimbles, bonding to the existing earth and painting etc. as desired by the Engineer-in-charge at site:
Bus Bar Chamber 63amp., 415volts Overall Dimensions (300mm x 345mm x 120mm) nomina (Basic Rate Rs.3975/- +30%prem.+5.35%)
Supply and erected of LED batten 20Watt LED (including LED driver) with high quality extruded aluminium with efficacy of LED fixture minimum 100 lumens per watt and operating voltage between 140 to 270 volt, input Ac frequency 50Hz+ 3% complete along with erection of the same with connection, testing etc. complete in all respect as approved and desired by engineer in charge at site. The certification and Specifications of the LED Fittings should be as approved by O/o Advisor(Technical), Govt of Punjab vide Letter no. At/2021/GL/1410-1422 dated 06/05/2021
Supply and erected of LED batten 40Watt LED (including LED driver) with high quality extruded aluminium with efficacy of LED fixture minimum 100 lumens per watt and operating voltage between 140 to 270 volt, input Ac frequency 50Hz+ 3% complete along with erection of the same with connection, testing etc. complete in all respect as approved and desired by engineer in charge at site. The certification and Specifications of the LED Fittings should be as approved by O/o Advisor(Technical), Govt of Punjab vide Letter no. At/2021/GL/1410-1422 dated 06/05/2021
Supply and erection of BEE 3-Star rating AC Ceiling Fan 1200mm (48") suitable for 230 V single phase with double bal bearing, copper wound, full aluminium body. 3Nos. of blades, white in colour. The mounting type is down rod mount. The product should possess a minimum air deleivery of 210 CMM (approx.). The rated speed of the the product must be minimum of 300 revolutions per minute and 5Nos. of speeds. The product should have a manufcaturer's guarantee /warranty of minimum 2 years. The product should be complete in al aspects with fan motor, bladeset, down rod, conopy set, shackle kit, twisted wire etc., including erection & testing of ceiling fan having connection with PVC insulated PVC sheathed two single core copper conductor (FR) cable 0.75 sq. mm complete in all respects as per satisfcation of the Engineer in-charge at site.
SITC of Wall Fan Size 400MM complete in all respect as approved and desired by the Engineer in-charges at site. The fan should conform to Technical Specifications attached.
Supply and erection of Heavy duty Exhaust Fan 300mm, 900RPM with aluminium louver shutter, double ball bearing longer life including flexible wire & petty material etc. for connections and testing complete in all respect as approved and desired by the Engineer in charges at site
Copper Earthing
Public Health Services
Providing, laying, jointing, fixing and testing ISIMarkeduPVCPipewithG.I. specialsas per ISI-4985, includingcost of G.I. specials such as tees, bends, sockets, elbows etc. testing inside building complete.
Providing,fixingandjointingISIMarkedGun Metal peet valves (HeavyPattern)asper IS 778withhandwheels,onG.I.Pipelines laid inthegroundor insidebuildings includingall carriages complete.
20mm i/d Gun Metal peet valve heavy pattern.
25mm i/d Gun Metal peet valve heavy pattern.
32mm i/d Gun Metal peet valve heavy pattern.
40mm i/d Gun Metal peet valve heavy pattern.
Making soak pit 2.5mouter Diametre 3.0 metre deep 230mm thick 1:5 brick work honeycombwithbricksof IstClassandS.W. drain pipe 100mmDiametre, 1.8m long complete as per standard design.
Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, C.C.1:4:8 ( 150mm thick) in foundation, cement concrete1:2:4benching 12.50mm thick cement plaster 1:2 with a floatingcoat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping50mmthickwith455mmx 455mm, 455mm x 610mm inside R.C.C. inspectionchambercoverandframe(Weight as per I.S.I specifications) painted with 3 coatsofblackbitumasticpaintconformingto I.S.I complete as per standard design.
450mmx600mminsidewith455mmx 610mm cover and frame light duty double seal
Providing and fixing in position singel socket SWRUPVCsoilwasteor antisyphonagepipes asper IS13592ofE.D.Cmanufactureorofany other reputed firm including cutting, jointing, wastage, but excluding cost of jointing
160mmo/dsinglesocketSWRUPVC pipe lines laid complete
110mm o/d single socket SWR UPVCpipe lines laid complete
70mm o/d single socket SWR UPVC pipe lines laid complete
Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern ISI marked, PVC short bend 32 mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.
Providingand fixing jet spraywith2'-6" long PVC pipe.
With C.P. Brass nut
Providing and fixing in position C.P brass basinmixerwithoutpop-upwastesystemwith 450mmlongflexiblehoseofapprovedmake (to the approval of Engineer-in-charge) complete in all respect
Providing and fixing in position stainless steel sinks of approved make (to the approval of Engineer-in-charge) 1mm thick,grade-304 (18/8) with waste coupling complete in all respect
Sink with drain board overall size 1070x464mm bowl size 430x355x200mm and waste coupling
Providing&Fixing inpostion15mm i/dbib cock of approvedmake (to the approval of Engineer-in-charge )complete in all respect.
C.P. brassBibcock foamflowwithout flange
Providing and fixing in positionC.I. gully trap coverweighingapproximately7.26kgandframe forgullytrapchamberclearopeningsize300mm x 300mm and out side size 330mmx330mm including painting the exposed surfacewith 3 coats of black bitumastic superior paint of approved manufacture etc.
Providing and fixing H.C.I. Floor traps conforming to I.S.I. Specification of reputed firm of the self cleaning design with S.S. grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors,etc.
With 100mm x 75mm i/d Floor Trap (weighing 5.8 Kg)
Providing and fixing in position H.C.I special for soil waste vent or anti syphonage pipes to I.S.I specifications of E.L.C manufacture or any other reputed firm including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.
100mm i/d H.C.I. Heal Rest Bend
75mm i/d H.C.I. Heal Rest Bend
Providing and fixing in position H.C.I special for soil waste vent or anti syphonage pipes to I.S.I specifications of E.L.C manufacture or any other reputed firm including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.
100mm i/d Cowls
Providing&placing inpositiononterrace(atall floor levels) HDPE water storage tanks of approvedmake(totheapprovalofEngineer-in charge) with cover with suitable locking arrangement andmaking necessary holes for inlet,outletandover flopipesbutwithout fittings and base support for tank.
Triple Layer Tanks (1000 ltr)
Providing& fixing inpositionon terrace (at all floor levels)HDPEtankcover forwaterstorage tanks of approvedmake (to the approval of Engineer -in-charge) complete in all respect.
For 1000 ltr capacity tank and above
Construction of Septic Tank size 5.00 Mtr x 3Mtr. Internal size with 2.5 Mtr. Internal depth in brick masonary, 4 no. chambers medium duty man hole cover complete as per drawing/specification andto the entire satisfaction of Engineer-in-charge
Please Enable Macros to View BoQ information
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.96 MB
SBD-compressed.pdf
Tender Documents • 17.49 MB
BOQ_324517.xls
BOQ • 0.44 MB
Download all tender documents and submit your bid