NIT No GE/ND-85/2025-26

Supply, installation, testing and commissioning of 1000mm long rigid architectural RGBW (W=3000K/4000K) LED Linear light with non-integral driver & housing of Extruded aluminium alloy & die cast aluminium end caps. The luminaire shall have emlectrosta caly applied polyester powder coating finish. The luminaire width Shall be 40mm & height of 60mm without brackets. The luminaire's integrated brackets shall be made of extruded aluminium & the same shall be so designed that the luminaire can be tilted +95°. The luminaire shall have silicon glue between optical cover & LED chamber to ensure proper IP66 protection. The luminaire shall be equipped with high-power Cree, Osram, Seoul only. The fixture shall have suitable beam angle as required & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK07 rated clear tempered glass. The LEDs shall have minimum CRI ≥80 & shall have SDCM≤4 and flicker≤3% . The fixture shall come with power & DMX cable of minimum 100mm length, should be able to follow Daisy Chain Topological connections. The fixtures shall be installed with have IP67 connectors. The luminaire shall have system wattage not exceeding 36W and system lumen output of not less than 1100 lumens. Fixture shall operating temperature range of - 30°C to 50°C. The fixture shall have a non-integral driver with input voltage of 24V DC. The luminaire shall have declared life of 50,000 burning hours at L70@ 35deg. The luminaire shall have class I insulation. The luminaire shall be compatible with DMX512 controller. The luminaire shall automatically addressable using hand-held addressing device. The luminaire shall be capable of 8-bit control of RED, Green, Blue & White (W=3000K/4000K) to produce 16.7million colours complete all as specified and directed. Make : Cat part model No-Lustre “GLIDE” Luminaire, Item No.-Li-92042-36 or equivalent in Iguzzini/We-ef/Led-Linear

Supply, installation, testing and commissioning of 500mm long rigid architectural RGBW (W=3000K/4000K) LED Linear light with non-integral driver & housing of Extruded aluminium alloy & die cast aluminium end caps. The luminaire shall have emlectrosta caly applied polyester powder coating finish. The luminaire width Shall be 40mm & height of 60mm without brackets. The luminaire's integrated brackets shall be made of extruded aluminium & the same shall be so designed that the luminaire can be tilted +95°. The luminaire shall have silicon glue between optical cover & LED chamber to ensure proper IP66 protection. The luminaire shall be equipped with high-power Cree, Osram, Seoul only. The fixture shall have suitable beam angle as required & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK07 rated clear tempered glass. The LEDs shall have minimum CRI ≥80 & shall have SDCM≤4 and flicker≤3% . The fixture shall come with power & DMX cable of minimum 100mm length, should be able to follow Daisy Chain Topological connections. The fixtures shall be installed with have IP67 connectors. The luminaire shall have system wattage not exceeding 36W and system lumen output of not less than 1100 lumens. Fixture shall operating temperature range of - 30°C to 50°C. The fixture shall have a non-integral driver with input voltage of 24V DC. The luminaire shall have declared life of 50,000 burning hours at L70@ 35deg. The luminaire shall have class I insulation. The luminaire shall be compatible with DMX512 controller. The luminaire shall automatically addressable using hand-held addressing device. The luminaire shall be capable of 8-bit control of RED, Green, Blue & White (W=3000K/4000K) to produce 16.7million colours complete all as specified and directed. Make : Model/cat part No “GLIDE” Luminaire, Item No.-Li-92042-36 of Lustre or equivalent in Iguzzini/We-ef/Led-Linear

Supply, installation, testing and commissioning of 5 Meter Rolls of high-performance flexible linear RGBW Neon Flex luminaire, made of Dow Chemical SILASTIC™ ET-7021 environmental-grade silicone rubber extrusion with high transparency, tensile strength and UV stability. The luminaire shall be of horizontal bend type with dimensions not exceeding 12 mm (W) × 20 mm (H), suitable for uniform linear façade illumination. The fixture shall operate on 24 V DC constant-voltage supply and consume not more than 15 W per meter. It shall consist of RGBW (4-in-1) high-brightness LEDs with colour wavelengths of Red 620–625 nm, Green 515–525 nm, Blue 460–465 nm, and White 4000 K (CCT), achieving rich colour mixing and a minimum efficacy of ≥ 90 lm/W. Each luminaire sec on shall be individually addressable via DMX512 protocol and integrated with UCS512CL IC, capable of 8 pixels per meter or as required. The fixture shall support 8-bit control of Red, Green, Blue & White channels, producing 16.7 million colours with smooth gradient transitions.The luminaire shall be IP67-rated for protection against dust and water ingress and shall be resistant to salt, weak acid/alkali corrosion, and UV radiation. It shall have cu able segments at 125 mm intervals and allow DMX512 compatibility. The Neon Flex shall exhibit uniform optical light distribution with no visible LED dots or shadows, maintaining consistent brightness throughout its length. The fixture shall be compatible with standard DMX controllers and support daisy-chain topology for data and power interconnection. The luminaire shall have a minimum service life of ≥ 30,000 hours (L70 @ Ta = 50 °C) complete all as specified and directed. Make - Iguzzini/We-ef/Led-Linear/Lustre.

Supply, installation, testing and commissioning of RDM-6 Wall DMX Splitter & Booster is a 6-output DMX/RDM splitter with DMX/RDM pass-through supporting bi-directional communications for discovery, addressing and DMX control. This unit takes the incoming DMX/RDM signal and splits the signal into six separate output channels allowing for expanding the number of devices controlled from 32 to 6 X 32. The output terminals are electronically isolated from the input & RDM through port and share a common ground reference. All six output ports have an independent output driver to boost the DMX/RDM signal complete all as specified and directed. Make : Iguzzini/We-ef/Led-Linear/Lustre.

Supply, installation, testing and commissioning of Compact master Content Program Controller (DMX controller) with capability to control minimum 8 DMX512 universes, playback scenes and anima ons stored in its SD card, and it can be used for offline scenes scheduling, setting brightness, white balance and playback speed adjustments. It should be able to amplify the DMX signal in cascaded connection & suppor automatic playback scheduling. It should support power-on startup and scheduled ming start along with capability of un ended operation and remote scene triggering if needed The Content Program Controller Shall have integrated LCD display & support IR remote control. The dimensions of the Content Program Controller shall be approximately 278X193X66 mm (#10%). It should be housed in aluminium casing. The Input voltage shall be 12VDC & shall have 2 R.J45 ports on Input side. The IEC classifica on shall be Class III. It should operate on DM512 protocol. The output shall have 8 X 3P lockable terminals. The power consump on shall be 8W (=10%). The Content Program Controller shall have one SD card slot for maximum 32GB card & the SD card being used shall be FAT32 format. The Content Program Controller shall come with 220-240V to 12V DC power supply. The IP rating of content program controller shall be IP20. The DMX controller/content program controller shall be from the same make/brand/ manufacturer as that of façade lighting luminares. The working temperature range shall be -30°C to 50°C. The successful bidder shall submit the technical data sheet for approval before supply of material complete all as specified and directed. Make : Iguzzini/We-ef/Led-Linear/Lustre.

Programming for lighting management system includes addressing for all smart ligh ng fixture along with mapping on connected system. All fixture to be programmed as per the site requirement. Min 5 Scenes to be created & configure on smart keypad for ease of operation of smart light system complete all as specified and directed. Make : Iguzzini/We-ef/Led-Linear/Lustre. Note: (a) The work has to be executed through OEM/OEM authorised agency only. (b) The contractor must sign bid specific MoU with the OEM for execution of work through OEM/OEM authorised agency. (c) The contractor must submit the copy of the MoU signed with OEM at the time of submission of Technical bid, failing which his technical bid shall be summarily rejected.

Supplying, fabrication, installation, testing and commissioning of LT panel not less than 3mm thick made out of modular polycarbonate thermoplastic enclosures outdoor type, factory made CPRI approved, floor mounting type, environment friendly, recyclable, UV resistant, halogen and silicon free, anti-acid and anti corrosive, IP-65 Protection in accordance with IEC 60529, 24 hrs astronomical time switch, auto/ manual selector switch, ON/OFF push buttons. The gasket material shall be plyurethane while the gas/ket shall be internally embedded including suitable working space suitable for 3 phase 4 wire system 415V, 50HZ, AC supply and fixed on raised PCC base 1:2:4, type B1 (20mm graded aggregate) raised base with cable glands, phase indicators, internal wiring, CT of suitable Ratio, digital voltmeter and ammeter, air passing holes with proper spacing to accommodate to all control switches and other accessories, cable connections with suitable size of lugs/thimble etc including suitable size canopy to cover the panel with proper fixing arrangement including excavation and earth work complete all as specified and directed and comprising the followings. Incoming : (a) MCB 32 Amps, 4 Pole - 01 No (b) Power contactor - 32 Amps (c) Surge protection device - 01 No (d) RYB Indicating lamp (e) Digital Voltmeter and ammeter of suitable rating (f) Start/stop Push Button -1 No (g) Over voltage/under voltage relay - 01 No Outgoing: (a) MCB DP, 32 Amps, 2 pole - 02 Nos

Supply, laying, testing and commissioning of 2 runs x 4 sqmm copper flexible cable for power supply to the fixure complete all as specified and directed by Engineeer-in-Charge. Make : Havells/Polycab/RR Kabel

Supply, laying, testing and commissioning of 2 runs x 2.5 sqmm copper flexible cable for power supply to the fixure complete all as specified and directed by Engineeer-in-Charge. Make : Havells/Polycab/RR Kabel

Supply and fixing of PVC conduit pipe of size 25mm suitable for passing cable complete all as specified and directed by Engineer-in-Charge.