ATTENDING DAY TODAY WATER SUPPLY BREAK DOWN COMPLAINTS INCLUDING REPAIR REPLACEMENT OF CONNECTED WORKS AND REPAIR MAINTENANCE OF MT VEHICLES UNDER GE I GOS

Amount

Dismantling and disconnecting of unserviceable parts of Tata Mobile 207 Veh BA No 07C-080817H, 14C-09971W , 13C-097227L reinstalling after repair/replacement of unservice-able parts complete to entire satisfaction of Engr-in-Charge. NOTE: Spare parts required to be replaced shall be measured and paid separately as mentioned here-in-below.

Engine oil

Oil filter element

Diesel filter element (set of two)

Air filter

Brake leather

Front wheel bearing

Coolant

Front shokers

Brake oil

Door lock driver side

Door lock rear door

Counter Shaft

Top gear

Gear Bearing

Synchronizing ring

Gear Oil

Gear Oil Seal

Gear Jain Kit

Fan Belt

Tie rod end

Bush kit complet

Ball joint assembly

Diesel pipe

Yoke and teeth

Shaft Nuts and Bolts

Mirror rolling machine

Engine mounting

U.J cross

Fly wheel Ring

Front Mirror with rubber beading

Head light assembly complet with tube

Main leaf spring

Leaf spring 2nd No

Leaf Spring 4th No

Leaf Spring clump

Nuts and Bolts with washer

Centre Bolts

U- Bolts

Wiper Arm & Blade

Alternator rectifier

Alternator rotor assy

Side view Mirror

Front indicator assembly

Rear indicator assembly

Ignition cum lock switch

Cluch cylinder assy upper

Clutch cylinder assy lower

Master cylinder assy

Clutch Plate

Pressure plate assy

Clutch release bearing

Dismantling of four wheels by greasing of four wheels including replacement of oil seal and reassembling complete all as directed.

Repair to gear by replacing main gear shaft.

Repair of seat complete including replacement of best quality Rexign, U foam & spring complete all as directed.

Alignment of wheel completely by computerized machine.

Cleaning of radiator assy complete by opening both tanks & cleaning the fins of the radiator by chemical and stopping the leakage by gas welding wherever required

Repair to FIP pump by over hauling the FIP and replacing all the spares of the FIP with the new spares and testing complete on machine all as directed.

Repair to Alternator by replacing carbon brush

Dismentling of Fuel tank assy complete from the vehicle and cleaning by pressure and refitting.

Repair of seat complete including replacement of best quality Rexign, U foam & spring complete all as directed.

Dismantling and disconnecting of U/S parts Hero Honda 100CC Veh BA No 19A-071993M19A-071994K, 15A-068526P. and BA No: NYA-03Nos Reinstalling after repair/replacement of U/S parts complete to entire satisfaction of Engr-in-Charge. NOTE: Spare parts required to be replaced shall be measured and paid separately as mentioned here-in-below.

Carburetor assy

Chain and chain sprocket.

Spark plug

Clutch plate

Shock absorber

Lock set complete

Side Looking Mirror

Kilometer cable

Head Light Tube

Back Light Complete

Break shoe Front and rear

Clutch cable complete

Accelerator cable complete

Engine oil

Dismantling and disconnecting of unserviceable parts of EICHER Model No 10.75 Veh BA No 14D-194341K,13D-191775P&17D-203855H and re-installing after repair/replacement of unserviceable parts complete to entire satisfaction of Engr-in-Charge.NOTE: Spare parts required to be replaced shall be measured and paid separately as mentioned here-in-below.

Engine Oil CRB plus 20W40

Oil filter element

Fuel filter element (set of two)

Door Handle with lock assembly

Door Handle

Coolant

Retreading of Tyres

Front Indicating light assly with bulb

Wheel bearing

Wheel cylinder assy

Break leather

Side view mirror

Head light assy complete with bulb (Halogen type)

Bumper corner

Self Starter Assy

Window glass with beading

Alternator carbon bush

Rectifier assy.

Alternator bearing

Back light assy. complete

Indicator assy.

Cutout 12 volts

Flasher

Main leaf spring

Nuts and Bolts with washer

Centre Bolts

U- Bolts

Wiper Arm & Blade

Ignition cum lock switch

Cluch cylinder assy upper

Cluch cylinder assy lower

Master cylinder assy

Cluch Plate

Pressure plate assy

Cluch release bearing

Fan Belt

Tie rod end

Diesel pipe

UJ cross

Top Gear

Gear Bearing

Synchronizing Ring

Fuel tank cleaning

Gear oil

Gear oil seal

Gear Cain Kit

Main Gear shaft

Repair of self starter by replacing of self bendex, carbon bush set, solenoid switch etc complete.

Dismantling the load springs and refitting after repair and giving suitable tensioning complete all as directed.

Dismantling of four wheels complete by greasing of four wheels including replacement of oil seal and re-assembling complete.

Setting of wheel alignment and setting of brake system including filling of brake fluid in master cylinder kit.

Repair of seat complete including replacement of best quality Rexign, U foam & spring complete all as directed.

Overhauling, greasing of King pin including replacement of oil seal complete.

Denting of vehicle, including welding wherever required

Dismentling of Fuel tank assy complete from the vehicle and cleaning by pressure and refitting.

Supply and fixing in replacement of maintenance free battery 12 volt 92 Ah including battery leads and initial charging of battery. Make:- Exide/ Amron.

Supply and fixing in replacement of maintenance free battery 12 volt 60 Ah including battery leads and initial charging of battery. Make:- Exide/ Amron.

Dismantling and disconnecting of unserviceable parts ofMaruti swift Dzire Veh BA No: NYA and re-installing after repair/replacement of unserviceable parts complete to entire satisfaction of Engr-in-Charge.NOTE: Spare parts required to be replaced shall be measured and paid separately as mentioned here-in-below.

Engine oil

Oil filter element

Fuel filter element (set of two)

Brake oil

Coolant

Attending day to day breakdowns/ complaints of damaged water supply lines in distribution system of DI/CI GI/PP-R Pipe line, restoration of water supply by stopping the leakage occured by deputing skilled /semi skilled man power for smooth functioning of water supply , complete all as specified and directed by Engineer-in-Charge . Bore of the pipe line of 15mm to 25mm

All as per Srl item No 141 above but Bore of pipe line 40mm to 50mm

All as per Srl item No 141 above but Bore of pipe line 80mm to 100mm

All as per Srl item No 141 above but Bore of pipe line 150mm to 200mm

All as per Srl item No 144 above but bore of pipe line above 300mm to 400mm Note for srl item no : 1 to 5 (a) Up to 0.5Cum of the earth work shall be included in the job & more than 0.5 Cum shall be measured and paid separately. (b) The complaint /breakdown shall be rectified by the contractor within 24 Hours.Any delay thereafter,recovery at double the rate quoted per job shall be deducted from the dues of contractor by the Engr-in-charge without any notice. (c) GI fittings like Elbow,union.socket nipple etc..deemed to included the unit rate quoted.

Taking down 0ld unserviseable Run lead joint and M&L for run lead joint of size 80 mm dia complete all as specified and directed

All as per Item No 146 above but 100 mm bore.

All as per Item No 146 above but 150 mm bore.

All as per Item No 146 above but 200 mm bore.

All as per Item No 146 above but 300 mm bore.

S&F in replacement of sluice valve 200 mm bore class PN - 1.6 with flanged and iron wheel head ,shut and open directed cast on it and including jointing materials,rubber gasket suitable size nut bolts and washer etc complete all as specified and directed. Make :Upadhay/Zoloto/Kirloskar or equivalent

All as per Item No. 151 above but 150 mm bore.

All as per Item No. 151 above but 100 mm bore.

All as per Item No. 151 above but 80 mm bore.

S&F in replacement of NON return valve 100 mm bore class PN - 1.6 with flanged including jointing materials,rubber gasket suitable size nut bolts and washer etc complete all as specified and directed. Make :Upadhay/Zoloto/Kirloskar or equivalent

All as per Item No. 155 above but 80 mm bore.

M& L for MS/CI/DI fittings up to 150mm bore such as collar, bends (any type radius, any angle, double end socketted or double flanged or spigot & socket, tail pieces (all socketed or all flanged with an equal & other end tapering bellmouth or flanged plates, connecting pieces straight (both end flanged or socketed of socket & flanged & spigot ends or bellmouth tailpieces ( one end flanged & other end spigot or socket or tapering as bell mouth or flanged ) caps blank flanges heavy duty suitable for mechanical joint/flanged joint with and incl taking down old fitting of any type and any size complete all as specified and directed.

Supply and laying in trenches Galvanised steel (Gl) tubing 'Medium grade' of 15mm bore dia with screwed socket joints, together with all tube fittings (such as bends, elbows, tees, short pieces, connectors, backnuts, diminishing pieces, caps, plugs and unions, etc.) with cutting, screwing, making forged bends on piping as required. insertion of Connectors where required or directed. including cutting through walls, floors, etc. and their making good and taking down old u/s pipe of any type all as specified and as directed for following size of pipes:Make : jindal/TATA (Note : Earthwork shall be measured and paid saperately under relavent Item)

All as per item No 158 above but 20mm bore dia

All as per item No 158 above but 25mm bore dia

S&F Gun-metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed in repair with taking down old u/s gate valve of 20mm dia. Make: Zoloto/kirloskar

All as per item No 161 above but of 25 mm dia

All as per item No 161 above but of 40 mm dia

All as per item No 161 above but of 50 mm dia .

S&F in repairs Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/ 20mm-210gms./ 25mm-455gms/ 40mm - 690 gms) of size 20 mm dia complete all as specified and directed. Make : Prayag/Polytuf

All as per Item No 165 above but 25mm dia

M & L for mechanical type joint made of MS sheet of size 6/8 mm thick along with rubber gasket nuts bolts and washers suitable for 80 mm bore dia of CI/DI pipe. Including Taking up or down old u/s joint all as specified and directed.

All as per item No 167 above but 100 mm bore dia

All as per item No 167 above but 150 mm bore dia

All as per item No 167 above but 200 mm bore dia

Excavation of trenches in any type of soil n.exc 1.5 M wide and n.exc 1.5 M in depth for taking out/laying of pipe lines and getting out forming bottom surfaces to required gradients complete all as specified and as directed.

Returning, filling in and including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick complete all as specified and directed

Removing excavated surplus materials to a distance not exceeding 50 Mtrs and deposited where directed at a level not exceeding 1.5 Mtr. Above starting point complete all as specified and directed.

Taking Down unserviceable GI/PPR pipes and S&F 3-layer PP-R polypropylene random copolymer concealed pipe (PN 16/SDR 7.4) UV stablised and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings, floors or in trenches etc of size 63 mm OD complete all as specified and directed. Make : SFMC or equivalent in approved by E-in-C

All as per Item No. 174 above but of size 50 mm OD.

All as per Item No. 174 above but of size 32 mm OD.

All as per Item No. 174 above but of size 25 mm OD.

S&F in repair of PP-R gate valves(brass inlet) as per requirement of size 63 mm OD complete all as specified and directed. Make : SFMC or equivalent in approved by E-in-C

All as per Item No. 31 above but 50 mm OD.

All as per Item No. 31 above but 32 mm OD.

All as per Item No .31 above but 25 mm OD.

M & L in replacement and making connection of pp-r distribution branch with pp-r main of size (16 to 40mm) by providing and fixing tee including cutting and making fusion joint etc as per required at site.

M & L in replacement and making connection of pp-r distribution branch with pp-r main of size (50 to 75 mm) by providing and fixing tee including cutting and making fusion joint etc as per required at site.

Taking down / removal of any damaged water point line from the position and connecting the pipe line 15 mm/20mm/25mm bore by providing new GI nipples, GI unions and GI sockets including exacavation and earth work , filling & good distributed surfaces all as specified and directed .

M&L cutting hole in RCC service tank removing rusted GI nipple of any size, providing new GI nipple of same size of providing pipe, making good to service tanks, making service tanks leak proof complete as directed

Boring across the road/hard surface with machanical boring equipments not less than 80 mm bore dia all as specified and directed.

Dismantling of old unserviceable and M & L for Construction of Brick masonry valve chamber of size 900x900x900mm (internal dimension) chamber depth to be reckoned from the top of PCC foundation to top of brick wall, including PCC1:4:8 type D2 in foundation PCC 1:2:4 type B1 in coping, brick work in cm 1:4, plaster 15 mm thick in CM 1:4 flush pointing externally as the work proceeds, MS Sheet cover 3.00 mm thick with handle and locking arranging and angle iron frame of size (25 x 25 x 5 mm) including painting with two coats of synthetic enameled paint over a coat of red oxide primer complete all as specified and directed

All as per Item No 187 above but 600x600x600mm

Taking up PPR/GI Pipe of 63MM OD Cleaning and removing mud,sand and stone Inside the pipe and Relaying the same complete all as specified and directed. Note: Earth work will be measured and paid for separtly.

All as per Item No. 189 above but 50 mm OD.

M/S. KISHAN ENGINEERING

M/S.J.BIJAYA KUMAR PATRO

M/S S. N. ENTERPRISES

M/s M M Engineering Systems

V.Venkata Ramaiah

R K Traders

R J ENTERPRISES