Creation of one Director Cabin at office of NHIDCL at 1st Floor, Tower A, World Trade Centre Nauroji Nagar, New Delhi-110029

Providing and laying vitrified floor and wall tiles in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all

11.41A colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc.,

11.41A.2. Size of Tile 600 x 1200 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic

11.48 coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting

and finishing complete as per direction of Engineer-in-charge.

1 Digitally signed by AMIT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply of 100 mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness 1.30

to 1.50mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

TOTAL FLOORING WORKS 479127.00

2 FALSE CEILING WORKS

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special

sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side

inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27

mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia

x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of

required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5

mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting

clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels

0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to

2.01 12.45 wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm

interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and

square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for

board, all as per manufacturer's specification and also including the cost of making openings for light

fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per

drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with

12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS Sqm 20.00 1145.95 22919.00

TOTAL FALSE CEILING WORKS

3 WALL FINISHES WORKS

2 Digitally signed by AMIT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE AMOUNT

Supply and installation of Aluminium Framed Glass Partition for Access and Cabin System for minimal frame,

room dividing solutions. Single glazed mullion free demountable glass partition using Toughened/ Laminated

glass in proprietary natural anodised/ Black aluminium sections ALT 50 of size 50mmx30mm with Concealed

sealing (No visible Gaskets/ Seals) with acoustic rating of Minimum 32 db with third party test certificate. The

profile will have Carpert Groove at the bottom on both sides for accomodating max. 8mm carpets. The

Glass to be fixed with help of proprietary stability GRIPPER Clamp to have a stable system. It should consists

of intermediate slim junction profiles for Glass to Glass vertical joints, 90 Degree L Junction and T Junction

profiles suitably to be used as per room configuration designs. No VISIBLE Clip Lines to provide clutter free

view at both side of section. The Glass to be offset mounted towards outer edge leading to minimum

aluminium frame on one side. Optional Profile Bottom Seal pair for additional accoustic. Glass thickness-10

(LSG) shall be included in the product.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed

and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash

fastener shall be paid for separately).

Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core

9.21 of block board construction with frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both faces of shutters:

3.04 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush

3.05 9.23 door shutters (over all area of door shutter to be measured). Sqm 5.00 401.40 2007.00

Providing and Fixing 22x922 mm D-type Handle Material : Stainless Steel. Finish : Satin Stainless Steel (SSS). of

3.06 MR approved make and model all complete as per the direction of Engineer-in-charge. Each 2.00 8549.00 17098.00

Providing and Fixing SS Mortise Lock Body SB/TB for door thickness 25-50 mm for of approved make and

3.07 MR model all complete as per the direction of Engineer-in-charge. Each 1.00 896.00 896.00

Providing and Fixing Double cylender Floor Spring- with Closing Force EN 3 with Maximum door weight 105

Kg. Maximum door width 950mm.Closing speed : 130°

Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight of floor spring approx : 6kg, 5,00,000

cycles Tested with 5 Years Warranty against manufacturing defect. CE certified for wooden doors all

complete as per the direction of Engineer-in-charge.

3 Digitally signed by AMIT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE AMOUNT

Providing 40x5mm flat iron hold fast 400mm long including fixing to frame with 10mm diameter bolts, nuts

and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3

coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and Fixing top and Bottom Strap of approved make and model all complete as per the direction

3.10 MR of Engineer-in-charge. Each 1.00 1010.00 1010.00

Providing and Fixing Dead lock Back set- 50 mm with Key Hole of approved make and model all complete

as per the direction of Engineer-in-charge.

Providing and Fixing 60 mm SS Cylinder One side knob and one side regular key (3 key) for wooden doors

of approved make and model all complete as per the direction of Engineer-in-charge.

Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce

Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil

(0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion

after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS

3.15 MR warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be endorsed by 3M India Limited Sqm 5.00 2467.00 12335.00

Architectural Market Department. Contractors payment wouldn't be released until & unless he/she produces

orginal warranty certificate from the manufacturer.

Providing and fixing Channelled woodwork acoustic wall panel of width of 192/132/128mm with finishing of

15 mm thick Grooved wooden acoustic panel of size 2420 mm, Groove Size 3.2mm at an interval of

21mm/28 mm c/c as per acoustic design / Architects’ approval, the wooden acoustic panels to be backed

with black acoustic fleece with NRC of 0.45 (NRC 0.8 with 50mm GW of 48kg/m3).the edge of panel shall be

Tounge and groov to be fixed with clips on aluminium profile designed specially fo the panel. the panel will

3.16 MR be mounted with the help of clips on Bollard Aluminium extruded Keel. The grooved acoustic panel Sqm 10.00 3858.00 38580.00

laminated in desired shade as per Engineer In charge / Architect’s approval.

Providing and fixing of 6 mm thick premium GRIHA rated Lacquered glass of approved color by Architect/

Client / Customer, fixed with compatible neutral grade silicon on a perfectly levelled 12mm thick water

proof marine plywood / MDF / Mineral fibre board which is mounted on RCC wall/any other structure.

Lacquered glass must be made industrially (using curtain coating process); opaque (if viewed against a

support wall), uniformly coated with PU lacquer (50 micron thick coating or more); panel to panel colour

consistency (measured by photo spectrometer); highly durable (passes hardness test for minimum 220

oscillations); humidity resistance (conforms to BS EN 1036 1999 or equivalent) ; environmentally friendly

having Low VOC (no lead, no arsenic, no copper, no formaldehyde), low VOC content <100g/l. Silicone

used should not react with lacquer coating (compatible neutral cure silicon)

4 Digitally signed by AMIT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE AMOUNT

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc

coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having

equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to

centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws

9.105 with nylon plugs and the studs 48mm wide having one flange of 34 mm and other flange 36 mm and 0.50

3.19 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm

centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush

to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450mm centre to centre,

and fixing of boards to both side of frame work by 25mm long dry wall screws on studs, floor and ceiling

channels at the spacing of 300mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99mm width (0.9mm thick having two flanges of

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass Reinforced Gypsum (GRG)

plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks)

Providing & fixing of straight Paneling for walls & Columns structures anchored in floor slab & celling,

cladded with Acrylic Solid Surface 12mm thick sheets straight fabricated on a single face, finished in matte

finish, pasted with industrial grade silicon on a robust substrate. Substrate shall be with suitable MS box

sections [Appx. 15 to 20 kg/ Sqm] as per structural requirement & duly painted with anti-rust red oxide

3.20 MR coating and covered with 12 mm thick water proof ply as per the design and dimensions approved. The Sqm 2.00 13363.00 26726.00

proposal includes the cost of preparing appropriate substrate surface over the civil structure provided, along

with material cost & installation / fixing on straight walls etc. FOR ALL WALL CLADDING, TABLE TOPS ETC.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

6.13 superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 20.00 1018.05 20361.00

3.26 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick Sqm 20.00 86.45 1729.00

13.4 12 mm cement plaster of mix :

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface

3.28 13.26 even and smooth complete. Sqm 100.00 214.30 21430.00

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

13.60.1 Two or more coats on new work Sqm 100.00 137.85 13785.00

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved

9.140 primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in-

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type Sqm 35.00 1084.60 37961.00

5 Digitally signed by AMIT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE AMOUNT

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved

primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in-

4mm thick MDF Board Sqm 35.00 600.00 21000.00

Providing and fixing metal system up to ceiling height, which includes frame work made of special section

power pressed/ roll form G.I. sheet with zinc coating of 120 GSM, consisting of Boral U track 52mm wide

having equal flanges of 30mm and 0.55mm thick (Base metal thickness) fastened to the floor slab and

ceiling soffit using rawl plugs with screw at 600mm centers, with first & last fixing point at not greater than 50

3.32 MR mm from either end. Boral C studs 50mm wide having one flange of 34mm, other flange 36mm, lip size 6 mm Sqm 10.00 955.12 9551.23

and 0.55mm thick installed perpendicularly within the flanges of floor and ceiling channels located directly

opposite to each other at not more than 610mm centers. Maintain 5 to 10mm gap between C Stud and

web of U Track.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede

finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to

IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having

3.34 12.57 density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & Sqm 10.00 307.35 3073.50

washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge.

TOTAL WALL FINISHING WORKS 372890.70

GRAND TOTAL 874936.70

GRAND TOTAL 874936.70

6 Digitally signed by AMIT

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR S NO QUANTIT TOTAL

DESCRIPTION UNIT RATE

2021 Y AMOUNT

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED BASIN MIXER (WALL MOUNTED) WITH SPOUT (COMPOSITE ONE

MR 1 PIECE BODY) EACH 1 16080.00 16080.00

Supply, Installation, Testing and Commisioning of TABLE TOP BASIN, SIZE: 630X460X130 MM

Supply, Installation, Testing and Commisioing of suitable compatible WASTE COUPLING 32MM- FULL THREAD- WITH CERAMIC CAP-*130MM

MR 3 HEIGHT *65MM CERAMIC CAP EACH 1 2398.00 2398.00

Supply, Installation, Testing and Commisioing of BOTTLE TRAP (WITH INTERNAL PARTITION) 32mm SIZE WITH 300mm & 190mm LONG WALL

MR 4 CONNECTION PIPES & WALL FLANGE EACH 1 3284.00 3284.00

Supply, Installation, Testing and Commisiong of RIMLESS, BLIND INSTALLATION WALL HUNG WC WITH UF SOFT CLOSE SLIM SEAT COVER,

MR 5 HINGES AND ACCESSORIES EACH 1 15087.00 15087.00

SET, SIZE: 375X520X400 MM

MR 6 Supply, Installation, Testing and Commisiong of PNEUMATIC CONTROL PLATE EACH 1 6641.00 6641.00

Supply, Installation, Testing and Commisiong of ANGULAR STOP COCK WITH WALL FLANGE

Supply, Installation, Testing and Commisiong of CONCEALED STOP COCK WITH ADJUSTABLE WITH WALL FLANGE 15mm

Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET) WITH 8mm DIA 1.2 METER LONG FLEXIBLE TUBE

AND WALL HOOK ALD-CHR-573 or equivalent

Supply, Installation, Testing and Commisiong of PNEUMATIC SINGLE PIECE SLIM CONCEALED CISTERN BODY WITH INSTALLATION

MR 10 KIT & “S-TYPE” DRAIN PIPE CONNECTION SET FOR WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE) EACH 1 8044.00 8044.00

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

Providing and fixing mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass

screws and washers complete.

18.53 13 Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931

18.53.1 15 mm nominal bore EACH 4 500.35 2001.40

18.8 14 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass

threaded fittings,

Concealed i/c fixing the

work including pipechases

cutting with clamps at 1.00good

and making m spacing.

the walls etc.,

18.8.1 15mm nominal outer dia pipes METRE 15 441.15 6617.25

18.8.2 20mm nominal outer dia pipes METRE 15 513.75 7706.25

18.51 15 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

18.51.1 15 mm nominal bore EACH 1 708.40 708.40

Digitally signed by AMIT

DSR S NO QUANTIT TOTAL

DESCRIPTION UNIT RATE

2021 Y AMOUNT

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil, waste, and vent, Type-B as per IS : 13592 suitable for

rubber ring joints, including all neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors), reducers, WC

connectors, couplers, expansion joints / bellows, cowels, clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp &

hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc. including chase cutting as required, excavation and back filling

in all kind of soils, suspended from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper completion of the work, breaking and

making good the walls and floors etc. after pipes have been duly laid and tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on 50x50x5 mm slotted angle. The cost will include all support

arrangements. The work includes commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 15.00 536.00 8040.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 10.00 416.00 4160.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6 Kg/ Sqcm rating with fitting for waste pipe from fixtures to

floor trap including reduces, enlarger, socket, couplers, bends, tees etc including fixing at wall/ ceiling level supported by clamp & hangers etc. cutting

MR 17 holes in wall/ floors/ slabs and making good the same with cement concrete 1:2:4 complete as required.

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating complete in all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 3 536.00 1608.00

MR 19 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. EACH 3 726.00 2178.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover with screws and other required fitting complete as required.

20 Providing and fixing stainless steel tray below sewage pipe of size 200x200x200 mm of grade SS304 including all accessories

Supply, Installation, Testing and Commisiong of HIGH FLOW SINGLE LEVER CONCEALED DIVERTOR FOR BATH & SHOWER

MR Supply, Installation, Testing and Commisiong of SPOUT FOR BUILT IN BATH/SHOWER MIXER EACH 1 9377.00 9377.00

Supply, Installation, Testing and Commisiong of OVERHEAD SHOWER 350x350MM ROUND EDGE SQUARE HEAD SINGLE FLOW (BODY & FACE

22 PLATE STAINLESS STEEL WITH CHROME PLATED) WITH RUBIT CLEANING SYSTEM

MR 23 Supply, Installation, Testing and Commissioning of 15 litre geyser EACH 1 12004.00 12004.00

MR Supply, Installation, Testing and Commisiong of SOAP DISH HOLDER EACH 1 4392.00 4392.00

MR Supply, Installation, Testing and Commisiong of TUMBLER HOLDER EACH 1 4309.00 4309.00

MR 25 Supply, Installation, Testing and Commisiong of TOWEL RACK 600MM LONG WITH LOWER HANGER EACH 1 15653.00 15653.00

MR Supply, Installation, Testing and Commisiong of ROBE HOOK EACH 1 2045.00 2045.00

MR Supply, Installation, Testing and Commisiong of TOILET ROLL HOLDER WITH COVER EACH 1 4978.00 4978.00

MR 27 Supply, Installation, Testing and Commisiong of TOWEL HOLDER EACH 1 3336.00 3336.00

Supply, Installation, Testing and Commisiong of Bamboo Tap Artize Jaguar Series Tap SS Finished Chrome LEVER

CONCEALED DIVERTOR

MR 29 Supplying & Fixing of Shower Cubical 10 mm thick Toughned Glass with Necessary Hardware as per Requirement. Nos 1 48500.00 48500.00

TOTAL 336454.80

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION

S NO UNIT QUANTITY RATE TOTAL AMOUNT

S NO UNIT QUANTITY RATE TOTAL AMOUNT

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in

surface / recessed medium class PVC conduit, with modular switch,

1.10 modular plate, suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc as

Wiring for group controlled (looped) light point/ fan point/call bell point

(without independent switch etc.) with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed PVC conduit,

A.2 and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed medium class

A.3 1.12 PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper Metre 100 334.00 33400.00

conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing

1.24 modular plate & switch box including connections but excluding

modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 10 122.00 1220.00

1.24.5 6 pin 15/16 amp socket outlet Each 10 197.00 1970.00

Supplying and fixing following size/module, GI box along with Modular

base & cover plate on existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Digitally signed by AMIT

DSR NO DESCRIPTION

S NO UNIT QUANTITY RATE TOTAL AMOUNT

S NO UNIT QUANTITY RATE TOTAL AMOUNT

Wiring for circuit/ submain wiring alongwith earth wire with the following

1.14 sizes of FR PVC insulated copper conductor, single core cable in

B.1 surface/ recessed

2 X 2.5 sq. mm + 1medium class

X 2.5 sq. mmPVC

wire as required

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 50 334.00 16700.00

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

E.11 1.19 copper conductor PE insulated, shielded with fine tinned copper braid Meter 100 47.00 4700.00

and protected with PVC sheath in the exisitng surface/recessed steel/

Supplying andasfixing

of following sizes medium class PVC conduit aong

1.21 with accessories in surface/ recess including cutting the wall and

E.12 making good the same incase of recessed conduit as required

Total of Electrical items 152268.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - HVAC WORKS

S No DESCRIPTION UNIT Rate Qty.

HVAC 2025 AMOUNT

Inverter Type- Cooling only

1 8.4.1 1.5 TR with 5 Star BEE Rating Each 67095 1 67095

REFRIGERANT PIPING - -

Supply, Installation, testing and commissioning including

and Nitrogen testing of following nominal sizes of soft/hard drawn

refrigerant piping for VRV/VRF system, complete with fittings, with

adjustable ring type hanger supports, jointing/brazing including

a 7.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm Rmt 20.0 346.0 6920

b 7.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm Rmt 10.0 487.0 4870

c 7.14.5 19.0 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm Rmt 15.0 739.0 11085

d 7.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm Rmt 15.0 904.0 13560

CONDENSATE DRAIN UPVC PIPE -

Supply, installation, testing and commissioning of uPVC Pipe

,complete with fittings, supports,U trap arrangement,Clean Plug with

6mm nitrile insulation and - -

accessories as per specifications, drawings.

4 MR Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. Mtr 35.0 161.6 5,656.00

5 MR Supply and fixing IP-55 based outdoor MCB box with 1 NOS 65 amp Nos 1.0 5500.0 5,500.00

MR Supply and fixing MS base frame for VRV outdoor stand as per

Total HVAC WORKS 103530 18072

Total HVAC Amount 121602

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - DATA and VOICE WORKS

S NO Description UOM Qty Rate Amount

A. UTP Components for Data

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper

(DSR conductors for Connectivity of Hub room to End Point.High Speed

1.53.1) Gigabit Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH

SupplyC6, Installtion , Testing and Comissioning of I/O port for CAT6 cable

2 MR termination at Work Station end. Keystone Unshielded Outlet, 180DG Nos. 10 450.00 4500.00

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

3 MR termination at Work Station end Redantant . Keystone Unshielded Outlet, Nos. 10 450.00 4500.00

180DG C6, Yellow

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

4 MR termination at Rack Side. Keystone Unshielded Outlet, 180DG C6, Blue Nos. 10 450.00 4500.00

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

5 MR termination at Rack Side end Redantant . Keystone Unshielded Outlet, Nos. 10 450.00 4500.00

180DG C6, Yellow

GRAND TOTAL (A+B+C+D+E) 52200.00

GRAND TOTAL (A+B+C+D+E) 52200.00

1 Digitally signed by AMIT

SCHEDULE OF QUANTIITES: AV SYSTEM

S.No. Item Description Item Description Qty Unit Rate Non DSR Amount

SITC of 55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness

Minimum 390cd/m2, Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1,

LAN-1,SPDIF-1 or Higher, Output Audio-1( Audio out to connect

additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System

Support Windows 7/8/10/Windows XP/Linux/Mac/Android (Windows

XP/Linux/Mac Support one point touch) , Multi touch point Min 20 Points

or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen Capture,

1 55" main LED display Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory 1 Nos. 148,500.00 148,500.00

(32GB),(Hisi 811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power

Indicator, or higher, Screen Share/Mira cast to Connect TAB/Mobile, Web

Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or higher , ISO9001,

ISO14001,ISO45001,

The display should be a smart screen and touch enabled alongwith

stylus/pen. The display should also have provision for OPS PC.

SITC of Premium High Speed Gold plated HDMI Cable 15 ft HDMI Cable,

Up to 4K @ 60 Hz (4096x2160), UHD @ 60 Hz (3840x2160) 8 bit color depth,

2 HDMI Cable max. 18.0 Gbps data rate, Material: Tinned copper, 28 AWG and also to 2 Nos. 2,741.00 5,482.00

comply the detailed technical specifications as attached

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - LIGHTING WORKS

S NO DSR/MR Description Image Unit QTY Rate AMOUNT

Supply, Installation, Testing and Commissioing of Recessed downlightwith

HPE (High-Performance Efficiency) with LED (Light Emitting Diode), system

power: 12 W, Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy,

Colour temperature of 4000 K, Neutral white, CRI > 80, 230V constant

current driver, 70% of luminous flux after 50,000 operating hours; energy-

efficient LEDs, direct light emission, housing in die-cast aluminium, Polyester

2 MR powder white coloured coat applied over a 5-stage pre-treatment trim, no 10 1395.00 13950.00

prismatic diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN

LOW SMOKE) wiring, Electronic control gear,

Protection class II, IP 40, Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm

Supply, Installation, Testing and Commissioing of Pendant/Recessed

luminaire with LED (Light Emitting Diode), system power 28 W, luminous

flux of luminaire 3080 lm, 110 LM/W system efficacy, direct light emission

CRI>80, colour temperature of 4000K, Neutral white, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours, energy efficient

LEDs, luminaire profile in aluminium, Plastic moulded end caps, Polyester

powder Aluminium white coloured coat applied over a 5- stage pre-

3 MR treatment, high efficiency glare-free snap fit micro-prismatic diffuser for no 4 4000.00 16000.00

homogeneous light distribution, ZHLS (Zero Halogen Low Smoke) internal

wiring, integral Electronic control gear, adjustable suspender,

Protection class I, IP 20, L = 1199 mm, B = 75 mm, H = 90 mm, PL max =

TOTAL 29950.00

1 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Item Description Qty Unit Rate Amount

Supplying & Placing of First & Second Floor Director Cabin Main table with made of

Director Sheesham Wood & Sattva model With modiesty panel The Size of Table is 270x105x76 in

Main Table Cm as per approved Design & Color Scheme by Client .

Director Supplying & Placing of Director Cabin Storage back unit The Size of Storage 400x45x75

2 Back in Cm The model , 3 part Which are made of Sheesham /Glass & the model is Sattva as Nos 1 320043.00 320043.00

Storage per approved Design & Color Scheme by Client .

Supplying & Placing of Drawer under table storage Which Are made of Sheesham Wood

3 & Sattva model The Size of Storage is 45x45x50 in Cm as per approved Design & Color Nos 1 27589.00 27589.00

Scheme by Client .

Director Supplying & Placing First & Second Floor Director Cabin of Side Unit Whicjh Are made of

Side Unit Sheesham Wood & Sattva Model - Large The Size of Side unit is 150x60x60 in Cm as per

approved Design & Color Scheme by Client .

Providing and placing in position High back chair.The seat shall be made up of 1.2 +/- 0.1

cm thick hot pressed moulded reconstituted wood & upholstered with leather and

moulded polyurethane foam. Size of back shall be (W)-46.0cm, (H)-57.0cm & size of seat

shall be (W)-49.0cm x (D)-49.5cm. High Resilience (HR) foam should be used in making

seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/-

2 kgf as per IS: 7888 for 25% compression. The back rest should be connected to the

mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0+/-

0.5cm for the comfortable back support to suitable individual need. Armrests should be

pressure die casted in polished aluminium with PP arm tops. The mechanism of chair shall

have following features:360 degree revolving type, Seat/Back tilt ratio of 1:3,

Synchronized tilt, Back tilt with 4 position locking and Side tilt tension adjustment knob

Director should be operated while taking back support for better adjustment of comfort. The chair

5 High back shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- Nos 1 60843.54 60843.54

chair 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with

5 nos twin wheel castor. The size of head rest shall be (W)26.0cm x 12.0cm(L). The size of

the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The

twin wheel castors shall be injection moulded in black polypropylene. Overall dimensions

of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from

pedestal below. Height from ground - min 113.5 to max 138.0 cms. Seat height - min

41.0cm to max 51.0 cm. Dimensions tolerance / variations shall be within +/- 1 cm.

Complete all as per the direction of Engineer in Charge.

S No Item Item Description Qty Unit Rate Amount

Providing and placing in position revolving visitor.The seat shall be made up of 1.2 +/- 0.1

cm thick hot pressed moulded reconstituted wood & upholstered with leather and

moulded polyurethane foam. The back shall be designed with contoured lumber support

for extra comfort. Size of back shall be (W)-45.0cm, (H)-49.0cm & size of seat shall be (W)-

49.0cm x (D)-49.5cm. High Resilience (HR) foam should be used in making seat & back

which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per

IS: 7888 for 25% compression. The back rest should be connected to the mechanism with

a drop-lift mechanism which can be adjusted in the range of 7.0+/-0.5cm for the

comfortable back support to suitable individual need. Armrests should be pressure die

casted in polished aluminium with PP arm tops. The mechanism of chair shall have

following features:360 degree revolving type, Seat/Back tilt ratio of 1:3, Synchronized tilt,

Director Back tilt with 4 position locking and Side tilt tension adjustment knob should be operated

Revolving while taking back support for better adjustment of comfort. The chair shall be provided

6 visitor & with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The Nos 3 52455.95 157367.85

Discussion pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin

Chair wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/-

1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of

Chair - 75.0 cm as measured from pedestal below. Height from ground - min 93.5 to max

110.5 cm. Seat height - min 41.0cm to max 51.0 cm. Dimensions tolerance / variations

shall be within +/- 1 cm. Complete all as per the direction of Engineer in Charge.

Director 3 Providing and Placing in position of Three seater long sofa as per approved by clind

7 Seater Sheesham made king size 3 seater Sofa 184x70x93 as per approved uphosty by cllient. Nos 1 203985.46 203985.46

Director 1 Providing and Placing in position of Single seater long sofa has been designed with

8 Seater Different Shade & Sheesham Family & Different Size Single Seater Sofa 91x70x93 Nos 2 74006.47 148012.94

Sofa approved By Client.

Director Providing and placing Coffee Table Sheesham Wood Make as per appropriate Size

9 Cofee 120x75x46 in cm as per approved by Client Nos 1 42468.07 42468.07

Director Providing and placing End Table Sheesham Wood Make as per appropriate Size

End Table 45X45X45 in cm as per approved by Client

Supplying & Placing PS Cabin of Director of Made of Sheesham Wood & Model Classic

11 Bhram W Quadro The Size of Visiter table 165x60x76 in Cm. as per approved Design & Nos 1 59593.00 59593.00

Color Scheme by Client .

Director Supplying & Placing PS Cabin Of Director of Made of Sheesham Wood & Model Classic

12 PS Under Bhram W Quadro Pattern The Size of Drawer Under Table Storage 45x45x50 in Cm. as per Nos 1 24278.00 24278.00

Storage approved Design & Color Scheme by Client .

Director Supplying & Placing PS Cabin Of Director of Made of Sheesham Wood & Model Classic

13 PS Side Bhram W Quadro Pattern The Size of Side Unit 120x60x60 in Cm. as per approved Design & Nos 1 82769.00 82769.00

Unit Color Scheme by Client .

S No Item Item Description Qty Unit Rate Amount

Providing and placing in position high back chair.The seat is made up of 1.2± 0.1cm thk.

Hot pressed plywood. The back is made up of injection moulded glass filled nylon &

upholstered using net fabric with high tenacity yarn. Seat Size:- 47cm(w) × 51.5cm (D). The

HR polyurathene foam is moulded with density =55+/-2 kg/m cube and hardness 16± 2

kgf as per is:7888 for 25% compression. The armrest has an up=Down adjustment of 8.5 ±

0.5cm which is provided in armrest structure. Armrest top has an integrated layer of

thermoplastic elastomer. Armrest is made up of plastic injection moulded nylon with

textured top. It shall have Front pivot synchro mechanism with following features. 360

degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position

Director locking with anti- shock feature, seat/back tilting ration of 1:2. The lumber support consists

14 PS High of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. Nos 1 12083.75 12083.75

back chair The height of lumber pad can be adjusted through two projecting knobs provided on the

rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be

greenguard certified. the work shall be carried out as per guidance and instructions

recieved from Engineer Incharge. This shall come along a headrest from same family. It

shall be SCS IAQ certified for Indoor Air Quality.Complete all as per the direction of

Engineer in Charge.

Providing and placing in position mid back chair.The seat is made up of 1.2± 0.1cm thk.

Hot pressed plywood. The back is made up of injection moulded glass filled nylon &

upholstered using net fabric with high tenacity yarn. Seat Size:- 47cm(w) × 51.5cm (D). The

HR polyurathene foam is moulded with density =55+/-2 kg/m cube and hardness 16± 2

kgf as per is:7888 for 25% compression. The armrest has an up=Down adjustment of 8.5 ±

0.5cm which is provided in armrest structure. Armrest top has an integrated layer of

thermoplastic elastomer. Armrest is made up of plastic injection moulded nylon with

Director textured top. It shall have Front pivot synchro mechanism with following features. 360

degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position

Medium locking with anti- shock feature, seat/back tilting ration of 1:2. The lumber support consists

of polypropylene pad with mouled polyurathene foam & covered with polyester fabric.

The height of lumber pad can be adjusted through two projecting knobs provided on the

rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be

greenguard certified. the work shall be carried out as per guidance and instructions

recieved from Engineer Incharge. It shall be SCS IAQ certified for Indoor Air

Quality.Complete all as per the direction of Engineer in Charge.