Development of Nohkalikai Precinct Area At Sohra , Meghalaya

Nohkalikai

Civil Works

Plumnbing Works

Electrical Works

Horticulture

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to any distance outside the periphery of the area cleared as identified by the contracting agency.

Earthwork in excavation by mechnical or manual means up to a depth of 3m below the existing ground level for foundation trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils. All kinds of soil (ordinary soil/ hard soil/ dense soil)

Earthwork in excavation by mechnical or manual means up to a depth of 3m below the existing ground level for foundation trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils. In ordinary rock (soft rock/ medium rock/ hard shale)

Earthwork in excavation by mechnical means up to a depth of 3m below the existing ground level for foundation trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils. In hard rock (Blasting prohibited)

Extra over rates on items "Earthwork in excavation all kinds of soil (ordinary soil/ hard soil/ dense soil), ordinary rock (soft rock/ medium rock/ hard shale) and hard rock (Blasting prohibited)" for each 1m depth or part thereof beyond the initial depth of 2m.

Earthwork in filling with available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering for all lead and all lift.

Earthwork in filling with borrowed earth/ stone dust (excluding rock) (including royalty) in trenches, plinth, sides of foundations etc in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering for all lead and all lift.

Sand filling in plinth in layers not exceeding 150 mm thick including breaking of clods, consolidating by ramming and watering complete as directed.

Providing and laying rubble soling by using best quality crushed metal of 40 to 63 mm and sand packed in required thickness, laid in levelling, spreading, grading and compacting with vibratory roller 8-10 tone as directed including all labour and materials and if necessary dewatering, complete.

Supplying, diluting, spraying, punching and injecting chemical emulsion i.e. Imidacloprid 30.5 % SC or equivalent for anti-termite treatment at foundation, filling and trenching levels. 1. The bottom surface and sides of the excavation made for foundation and basement shall be treated with the chemical emulsion at the rate of 5 liters per square meter or as per manufacturer recommendation. 2. The chemical emulsion is seep or inject through holes up to 75 mm deep at 150 mm centers both ways with 12 mm diameter mild steel rod on the filled surface. The top surface of the consolidated earth within plinth walls shall also be treated with chemical emulsion at the rate of 5 liters per square meter or as per manufacturer recommendation before laid the sand bed or sub grade. 3. The external perimeter of the building should be treated with chemical emulsion at the rate of 7.5 liters per square meter or as per manufacturer recommendation. The chemical emulsion is seep/ injected though holes up to 300 mm at 450 mm intervals with 16mm diameter mild steel rod or driller machine after completion of filling/ plinth work of the building periphery. 4. The wooden material and electric conduits should be carried out oil base treatment at the ground floor. The contractor shall submit bond of 5 year warranty.

Filling sunken floor with broken brick bats and sand including compacting and supplying of materials complete as specified and directed for all levels.

Providing and placing in position serrated with central bulb (225 mm wide, 8-11 mm thick) PVC water stops conforming to IS:12200 for construction or expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete.

Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering- all work up to plinth level in 1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairingstrength; including pumping of concrete to site of laying, curing, carriagefor all leads; including the cost of centering, shuttering and pumping of concrete to site of laying, curing, carriage for all leads, finishing; but excluding reinforcement as per direction of the Engineer in-charge for all works up to plinth level of M25 grade concrete with minimum cement content of 330 kg/cum.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairingstrength; including pumping of concrete to site of laying, curing, carriagefor all leads; including the cost of centering, shuttering and pumping of concrete to site of laying, curing, carriage for all leads, finishing; but excluding reinforcement as per direction of the Engineer in-charge for all works above plinth level of M25 grade concrete with minimum cement content of 330 kg/cum.

Supplying, fitting and fixing in position FE 500D Thermo-Mechanically Treated reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers, welding (if required), couplers (if required) etc. complete for all levels/ all heights/ all floors. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurement for the same is required.)

Providing and fixing rock anchors using 25 mm dia TMT bars inserted in 32 mm dia drilled holes with epoxy resin based injection grout, conforming to relevant international guidelines and having valid ETA/ ETAG approval for rebar installation in dry, wet and water-filled drill holes, suitable for hammer drilling, compressed air drilling, hollow drill bits and diamond core drilling. The grout shall be supplied in hard cartridge packing system with static mixer for proper dispensing. The work includes drilling of holes to required depth as per approved drawings, cleaning of holes with wire brush and compressed air jet, removal of water if any, dispensing of epoxy grout, insertion and fixing of anchor bar to required embedment length/ depth, curing, scaffolding, safety arrangements, and cleaning of the site after completion, all complete as per specifications and direction of Engineer in-charge. Reinforcement bars shall be measured and paid separately under relevant tender item.

Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:4 (1 cement: 4 coarse sand).

Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in superstructure above plinth level in all shapes and sizes in cement mortar 1:4 (1 cement: 4 coarse sand).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations, plinth and superstructure above plinth level in cement mortar 1:4 (1 cement : 4 coarse sand)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) up to plinth level with cement mortar 1:6 (1 cement: 6 coarse sand).

Random rubble masonry with hard stone in superstructure above plinth level including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) with Cement mortar 1:6 (1 cement: 6 coarse sand).

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoir, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative(internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50 mm. The work shall be carried out for vertical surface two coats @ 0.70 kg per sqm per coat and horizontal surface one coat @1.10 kg per sqm all complete as per direction of the Engineer In-charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed or sunken portions of W.C., kitchen, pantry and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with wate

r proofing compound conforming to IS : 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400-micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). The product performance shall carry guarantee for 10 years against any leakage.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/ brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645, to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order as directed by the Engineer In-charge”: With average thickness of 120 mm and minimum thickness at khurra as 65 mm. The product performance shall carry guarantee for 10 years against any leakage.

Supplying, filling and laying cut piece AAC blocks as light weight filler material and gap filled with 1:6 cement mortar in sunk layers of 15 cm thick including watering, placing, ramming and consolidating etc. as per drawings and directed by Engineer In-charge.

12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand).

15 mm cement plaster on rough side of single or half brick wall of mix 1:4 (1 cement: 4 coarse sand).

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:4 (1 cement : 4 fine sand).

Providing and fixing GI or Fiber chicken wire mesh jali in 22 gauge at all junction of concrete and brick/ AAC block work or between two different materials after making "V" groove and filled with rich 1:1 cement mortar, nailing for all levels/ all heights/ all floors etc. complete. The evidence of all junction photographs shall be part of RA bills for payment.

Providing and applying plaster of paris putty of average 6 mm thickness over plastered or concrete surface to prepare the surface even, level and smooth complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered or concrete surface to prepare the surface even and smooth complete.

Providing and applying priming coats with water thinnable cement primer and two coats painting with premium acrylic emulsion paint of interior grade of approved brand and manufacture, having Volatile Organic Compound (VOC) content less than 50 g/litre, including surface preparation, scaffolding, applying additional coats wherever required to achieve even shade colour as direction of Engineer in-charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications, including scaffolding: Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm.

Finishing walls with textured exterior paint of required shade, including scaffolding: New work (Two or more coats applied @ 3.28 ltr/10 Sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 Sqm.

Kota stone 25 mm thick slab in flooring laid over average 20mm thick base of cement mortar 1:4 (1-cement : 4-coarse sand) or chemical adhesive as per manufacturer and filled 5 mm groove with epoxy grout to match the shade of slab including rubbing, scrubbing, full depth flushed or struck pointing, polishing and chamfering/ nosing at edges by using mechanical/ manual means etc. complete as approved by the Consultant/ Engineer In-charge.

Kota stone 25 mm thick slab in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) or chemical adhesive as per manufacturer and filled 5 mm groove with epoxy grout to match the shade of slab including rubbing, scrubbing, full depth flushed or struck pointing, polishing and chamfering/ nosing at edges by using mechanical/ manual means etc. complete as approved by the Consultant/ Engineer In-charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished Steel Grey Granite stone, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, door & window sills, jambs, shelves, skirting, facias and similar locations of required size, approved shade, colour and texture laid over average 20mm thick base of cement mortar 1:4 (1-cement : 4-coarse sand) or chemical adhesive as per manufacturer and jointed 5 mm groove filled with epoxy grout to match the shade of slab including rubbing, scrubbing, full depth flushed or struck pointing, polishing and chamfering/ nosing at edges by using mechanical/ manual means etc. complete as approved

by the Consultant/ Engineer In-charge.

Providing and laying Leather finish Steel Grey Granite stone flooring, coping, sill, jamb, lintel, steps, tread, riser, ramp, skirting etc. in required design and patterns, in linear as well as curvilinear portions of all complete as per the architectural drawings with 18 mm thick stone laid over average 20mm thick base of cement mortar 1:4 (1-cement : 4-coarse sand) or chemical adhesive as per manufacturer and filled 5 mm groove with epoxy grout to match the shade of slab including rubbing, scrubbing, full depth flushed or struck pointing, buffing and chamfering/ nosing at edges by using mechanical/ manual means etc. complete as approved by the Consultant/ Engineer In-charge.

Providing and laying Leather finish Kadapa stone flooring, dado, wall lining, coping, sill, jamb, lintel, steps, tread, riser, ramp, shelves, counter, platform, skirting etc. in required design and patterns, in linear as well as curvilinear portions of all complete as per the architectural drawings with 18 mm thick stone laid over average 20mm thick base of cement mortar 1:4 (1-cement : 4-coarse sand) or chemical adhesive as per manufacturer and filled 5 mm groove with epoxy grout to match the shade of slab including rubbing, scrubbing, full depth flushed or struck pointing, buffing and chamfering/ nosing at edges by using mechanical/ manual means etc. complete as approved by the Consultant/ Engineer In-charge.

Providing and laying Bush Hammered finish Kadapa stone flooring, dado, wall lining, coping, sill, jamb, lintel, steps, tread, riser, ramp, shelves, counter, platform, skirting etc. in required design and patterns, in linear as well as curvilinear portions of all complete as per the architectural drawings with 18 mm thick stone laid over average 20mm thick base of cement mortar 1:4 (1-cement : 4-coarse sand) or chemical adhesive as per manufacturer and filled 5 mm groove with epoxy grout to match the shade of slab including rubbing, scrubbing, full depth flushed or struck pointing, buffing and chamfering/ nosing at edges by using mechanical/ manual means etc. complete as approved by the Consultant/ Engineer In-charge.

Providing and laying Lather finish Steel Grey Granite stone flooring, coping, sill, jamb, lintel, steps, tread, riser, ramp, skirting etc. in required design and patterns, in linear as well as curvilinear portions of all complete as per the architectural drawings with 40 mm thick stone laid over average 20mm thick base of cement mortar 1:4 (1-cement : 4-coarse sand) or chemical adhesive as per manufacturer and filled 5 mm groove with epoxy grout to match the shade of slab including rubbing, scrubbing, full depth flushed or struck pointing, buffing and chamfering/ nosing at edges by using mechanical/ manual means etc. complete as approved by the Consultant/ Engineer In-charge.

Providing and laying Glazed Vitrified tiles matt/ antiskid finish size of 600 mm x 600 mm in flooring and skirting (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid over average 20mm thick base of cement mortar 1:4 (1-cement : 4-coarse sand) jointing with grey cement slurry @3.3 kg/sqm or chemical adhesive as per manufacturer and filled 5 mm groove with epoxy grout to match the shade of tiles etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Providing and laying Double charge vitrified tile polished finish size of 600 mm x 600 mm in flooring, skirting, riser of steps and dados, (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid over average 20mm thick base of cement mortar 1:4 (1-cement : 4-coarse sand) jointing with grey cement slurry @3.3 kg/sqm or chemical adhesive as per manufacturer and filled 5 mm groove with epoxy grout to match the shade of tiles etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including filling the gaps with ordinary white cement mixture & mixing with synthetic polyester fibre, triangular in shape having specific gravity of 1.34 to 1.40, cross section size ranging from 10 to 40 micron & length up to 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar, including providing and mixing water proofing material in mortar @ 1 kg per 50 kg of cement, all complete as per direction of Engineer In-charge.

Providing, supplying, fitting, fixing and laying of 100 mm thick dressed stone block flooring (Cherra/ local stone block) laid on 25 mm thick base in cement mortar 1:3 and jointed with grey cement slurry including clearing, rubbing, chipping etc. complete as directed by Engineer In-charge.

Providing, supplying, fitting, fixing and laying of dressed stone block kerbing of 300 x 300 x 300mm (Cherra/ local stone block) laid on 25 mm thick base in cement mortar 1:3 by fixing in 100mm thick cement concrete vata @ both side and jointed with grey cement slurry including clearing, rubbing, chipping, buffing etc. complete as directed by Engineer In-charge.

Providing and fixing 10x10x7.50 cm Granite Cobble stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20 mm thick base mortar 1:4 (1 cement: 4 coarse sand) with joints 10 mm wide filled with same mortar including ruled pointing ctc. complete as per direction of Engineer In-charge.

and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer In-charge but excluding the cost of painting.

Providing & fixing 8 mm thick Calcium Silicate Board false ceiling made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process, at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 150 gms/ Sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm c/c, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.l channels 45 x15 x 0.90 mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm Each having lips of 10.5mm, at 450 mm c/c, shall be fixed in a direction perpendicular to G.l intermediate channel with connecting clip made out of 2.64 mm dia x 230 mm long G.l wire at every junction, including fixing perimeter channels 0.50 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25 mm at 230 mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes, finishing with jointing compounds in three layers covering up to 150 mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture’s specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in charge but excluding the cost of painting.

Providing & fixing 600mm x 600mm company fitted access panel for ceilings, to services running above the false ceiling including 12.5 mm thick tapered edge gypsum (MR) Moisture Resistant board door with powder coated Aluminum Alloy 6063 T6 Extrusion section frame. Each panel is comprise a push latch closing mechanism with door retaining safety cable & hook, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes, finishing with jointing compounds in three layers covering up to 150 mm on both sides of joints and two coats of primer suitable for boards all as per manufacture’s specification but excluding the cost of painting.

Providing and fixing aluminium work for doors, windows, ventilators, louvers, panelling, false ceiling, partition, curtain wall, facade and cladding with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confirming to lS:733, lS:1285 and aluminium quality as per grade 6063 T5 or T6 as per BS 1474, providing & fixing with dash/ anchor fasteners of required diameter and size, including necessary filling up the gaps with weatherproof structural sealant at junctions, i.e. at top, bottom and sides with required microwave cured EPDM rubber/ neoprene gasket, wool pile, silicon sealant etc. Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ panelling, sleeves, cover plate, space plate, extensions, C.P. brass/ stainless steel screws, etc. all complete as per architectural intent drawings, approved shop drawings submitted by Contractor and the directions of Engineer In-charge. For fixed portion polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing aluminium work for doors, windows (sliding/ openable), ventilators, louvers, panelling, false ceiling, partition, curtain wall, facade and cladding with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confirming to lS:733, lS:1285 and aluminium quality as per grade 6063 T5 or T6 as per BS 1474, providing & fixing with dash/ anchor fasteners of required diameter and size, including necessary filling up the gaps with weatherproof structural sealant at junctions, i.e. at top, bottom and sides with required microwave cured EPDM rubber/ neoprene gasket, hinges, top & bottom pivot & double acting hydraulic floor

spring type including arrangement and making necessary holes, stainless steel ball bearing, L type lock handle, wool pile, silicon sealant and making provision for fixing of fittings wherever required etc. Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ panelling, sleeves, cover plate, space plate, extensions, C.P. brass/ stainless steel screws, etc. all complete as per architectural intent drawings, approved shop drawings submitted by contractor and the directions of Engineer In-charge: For shutters of doors, windows (sliding/ openable) & ventilators including providing and fixing hinges/ pivots, stainless steel ball bearing, L type lock handle, wool pile and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever SS 316 grade handles inclusive of 1 master key and 3 computerised keys of approved quality with necessary screws etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS: 3564, embossed on the body, door weight up to 90 kg), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing SS 316 grade tower bolts, ISI marked, satin finished as approved quality & make with necessary screws etc all complete: 300x10 mm.

Providing and fixing 12 mm thick pre-laminated Medium Density Fiber (MDF) board exterior grade-I IS: 14587:1998 marked, factory pressed 1.5mm thick laminated on both sides, fixed to aluminum frame or shutter with screws, adhesive and necessary hardware etc., including edge finishing, cutting and making openings if required, all complete as per direction of Engineer In-charge, but excluding the cost of aluminum framing.

Supplying and fixing rolling shutters of approved make, made of 80x1.20 mm M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 -part 1 and 1.20 mm thick M.S. top cover of required thickness for rolling shutters.

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters.

dia M.S. bar instead of laths as per design approved by Engineer In-charge. (Area of grill to be measured).

Providing and fixing Stainless Steel (Grade 316) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories such as posts, handrails, balusters (or pickets/ spindles), supports, infill, base plates, connectors and brackets, etc. and stainless steel dash fasteners, stainless steel nut-bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer In-charge, (for payment purpose only weight of stainless steel members shall be considered).

Providing and fixing pre-coated Galvanised Iron profile sheets (size, shape and pitch of corrugation as approved by Engineer In-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 150 grams per sqm as per IS: 277, in 240 MPa steel grade, 5–7 microns epoxy primer on both side of the sheet and polyester top coat 15–18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 meter or as desired by Engineer In-charge. The sheet shall be fixed using self-drilling/ self-tapping screws of size (5.5×55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses Including cutting to size and shape wherever required.

including scaffolding, safety majors, disposing the debris, cleaning for all levels/ all height as per structural consultant's drawing and approval of Engineer In-charge etc. compete. Rate shall be inclusive of filling the hole with waterproof non-shrink grout in good manner. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency only. (a) holes from 50mm to 75mm dia.

Core Cutting: Executing core cutting by wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC member without vibration by core cutting (diamond drilling) machine including scaffolding, safety majors, disposing the debris, cleaning for all levels/ all height as per structural consultant's drawing and approval of Engineer In-charge etc. compete. Rate shall be inclusive of filling the hole with waterproof non-shrink grout in good manner. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency only. (c) holes from 101mm to 130mm dia.

Providing and fixing heavy duty SFRC type manhole cover of 600x600mm clear opening with frame and cover with provisions to match with surrounding finished level without any undulation for smooth running as approved and as specified having clear opening of given size and also covers have pick holes with a handle to lift manhole cover. It allows to fix with C:M 1:3 mortar with proper grading and on true line & level etc. complete as directed by EIC.

Providing, placing and fixing 110mm dia PVC sleeve in slab, beam, walls, etc. as per the details shown in drawing.

Providing and fixing 6 mm thick mirror of superior glass (of approved quality) of required shape and size fixed with silicon or chemical adhesive as per manufacturer on 6 mm thick marine ply conforming to IS: 710 backing and teak wood moulded frame with necessary screws or anchors etc. complete.

Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer In-charge and accordance with applicable specifications.

Designing, supply, fabricating, transporting, hoisting, fixing and testing of wet stone cladding system comprises 20 mm thick slate grey sandstone of approved shade in various elements of any size, shape including curvature, pattern and design as securely fixed over average 12mm thick base of cement mortar 1:3 (1-cement : 3-coarse sand) or chemical adhesive as per manufacturer, jointed 5 mm groove filled with epoxy grout to match the shade of slab and silicon coating on external stone face including rubbing, full depth flushed or struck pointing, chamfering/ nosing at edges and scrubbing to achieve clean surface by using mechanical/ manual means etc. complete as approved by the Consultant/ Engineer Incharge. Rate shall be inclusive of submission of shop drawings with design calculation, 3D view, approvals, stone slab, silicon coating, scaffolding, tools and tackles for all levels/ all heights/ all floors etc. complete.

Design, supply, fabrication, erection and installation of decorative bamboo entrance canopy structure (lattice or diamond pattern) including treated bamboo columns and roof framework in 100mm arched shape and latice or dimond pattern roofing in 25 mm memebers tied in woven method and securely anchored to custom-designed MS ring brackets or holding frames fixed around the column and roof. All bamboo components shall undergo chemical treatment (i.e. Boron or CCA) to protect against water ingress, insect attack, and decay, followed by finishing with an outdoor-grade natural oil or a clear UV-resistant coating. The treated bamboo shall be properly dried and cured in accordance with best practices and the provisions of IS 9096:2006, ensuring long-term resistance to termites, fungi, and environmental exposure. MS brackets and supports shall be rust-protected with zinc primer and synthetic enamel or powder-coated finish. Installation to be completed as per approved architectural design and mock-up sample, ensuring uniform spacing, alignment, and aesthetic quality.

Design, supply, fabrication, erection and installation of decorative bamboo cladding on columns of height 5.5 m in curve profile @ 75 c/c and roof @ 75 c/c tied @ 750 c/c using natural treated bamboo poles of diameters (typically 75 mm). Bamboo poles shall be arranged vertically and artistically in a tree-like or flared configuration, securely anchored to custom-designed MS ring brackets or holding frames fixed around the column and roof. All bamboo components shall undergo chemical treatment (i.e. Boron or CCA) to protect against water ingress, insect attack, and decay, followed by finishing with an outdoor-grade natural oil or a clear UV-resistant coating. The treated bamboo shall be properly dried and cured in accordance with best practices and the provisions of IS 9096:2006, ensuring long-term resistance to termites, fungi, and environmental exposure. MS brackets and supports shall be rust-protected with zinc primer and synthetic enamel or powder-coated finish. Installation to be completed as per approved architectural design and mock-up sample, ensuring uniform spacing, alignment, and aesthetic quality.

Aluminium Standing Seam Roofing System with Flashing, Skylight, Gutter, Fall Protection System for maintenance, Step Walkway System for maintenance: Designing, fabricating, testing, installing and fixing in position Double Skin Roofing System of straight & tapered sheets with 2 coats of PVDF coating. The roofing system will have required minimum thermal conductivity of 0.034 W/m-K as per ASTM C518, U Value of 0.35 W/m²-K, R Value of 3 m²-K/W, Sound Transmission Class (STC) rating of 50 dB as per Int

ernational Building Codes and wind pressure as per site weather condition. Top Layer: Aluminium Standing Seam SF 65/400 in self-supported fix roofing system in 1mm thick is profiled on site with Aluminium Halter (Straight/ Tapered/ Curved/ Infinity). Halter to be fixed on purlins or brackets with SS 304 screws. The feed material for top skin is manufactured out of nominal 1mm thick AA 3004 aluminium alloy in 2 coats of 25microns PVDF finish (colour as per Architect approval). The profile panels should have 3nos of mini ribs for extra strength. The roof element will be supported and joined longitudinally with an electrically operated closure zipping machine over concealed extruded secret halter integrated into the longitudinal element flanges thereby allowing for the possibility of transmitting reaction forces resulting from positive and/or negative loads, accommodating unobstructed thermal movements resulting from the specified ambient temperature variation and other loads as per IS codes. The sheet to be laid as per the requirement of building geometry provided by Architect.Second Layer: 100mm thick 2-hour Fire rated Rockwool insulation of 100 kg/cum density conforming to IS 8183. The insulation must be certified by EUCEB as non-carcinogenic, bio soluble and also comply to the Building Standard considering Fire Performance of EN 13501-1 Non-combustible/ Euro Class A1, BS 476 Part 4 Non-combustible. BS 476 Part 6 Fire Propagation, BS 476 Part 7 Surface Spread of Flame, UL 723– SDI & FSI 0 (Xero) Melting Point ASTM E794 > 1000ºC.Third Layer: Top Hat Bracket of 2mm made from GI steel sheet.Fourth Layer: Top Hat Batten made from 2mm GI steel sheet to be fixed above the 0.5mm liner sheet.Fifth Layer: Vapour Control Layer is a reinforced polythene vapour barrier of double sided aluminium foils of 200 microns with Moisture Vapor Transmission Rate (MVTR) of 343 MN.s/g and water permeability of <0.7 g/m2/daySixth Layer (Bottom Sheet): Trapezoidal Galvalume minimum thickness of 0.50mm (TCT) profile sheet of 980-1250 mm effective cover width and 28-35 mm height ribs with pitch at 200-250 mm centre-to-centre using self-drilling/ self-tapping zinc coated/ S.S. screws of required size with EPDM seal complete up to any pitch in Straight/ Tapered/ Curved/ Infinity surfaces.The complete system must be waterproof with 10 years guarantee. The rates shall inclusive of wind clamps, anchor fasteners, halters, 1mm thick aluminium flashing in 2 coats of 25microns PVDF finish at all edges, opening/ skylight provision of addition 2mm thick aluminium flashing in 2 coats of 25microns PVDF finish, 2mm thick aluminium gutter (up to 1200mm) in 2 coats of 25microns PVDF finish with down take spouts, fall protection system for maintenance, step walkway system at centre for maintenance, double side vulcanized rubber expansion joints, rockwool insulations and other required hardware/ accessories like cover plate, end caps, welding at joints etc. for complete system in all areas, periphery, sides and edges etc. Aluminium standing seam complete system with maintenance provisions rate shall be measured in square metre of top surfaced planned area.

Providing and fixing three layered Asphalt Shingles Roofing System consisting first layer of 3.5 mm thick asphalt roofing shingles conforming to EN 544 of approved colour and pattern fixed with manufacturer-recommended adhesive and stainless steel 410 grade fasteners, second layer of 3 mm thick SBS-modified bituminous waterproofing membrane applied over a coat of bituminous primer in proper overlaps and third layer of10 mm thick exterior-grade cement board conforming to IS 14862 fixed with corrosion-resistant screws by using preservative-treated wooden termite free batten framing to achive flat level over roofing system. The work shall be executed complete with all materials, labour, tools, scaffolding, and finishing ensuring proper alignment, sealing, and structural stability. The complete system must be waterproof with 10 years guarantee.

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and Technical Specification Clause 1204.3.8.

Providing & laying weep hole in abutments, return walls and retaining walls etc. by using PVC pipe of 100mm including laying in proper grade and jointing the completed as per detailed specification and deta

il drawings.

Providing and laying factory made 80mm thick factory made shot blasted precast M35 grade Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness, colour, pattern, design & size/ shape including curvature as specified in drawing, made by table vibratory method/ pneumatic compressed using steel mould, laid over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern by machine only, finishing and sweeping extra sand etc. complete as approved by the Consultant/ Engineer In-charge.

Providing and laying factory made steel mould vaccum wet pressed precast M30 grade cement concrete kerb stone of various types (Half Batter, Bull Nose, Splay, Square, Flat, Offlet, Transition, Dropper, Angle, Cuvelier, Radius, Quadrant, Offlet, Sloped, Dished Channel with or without Outlet, L Profiled, Gully, Drain Cover etc.) in position to the required line, level and curvature, fixed with cement concrete 1:2:4 (1-Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm nominal size) in vata and jointed with cement mortar 1:1 (1 cement: 1 fine sand), including making joints with or without grooves with throughly curing, rendering with cement slurry, cleaning the joints neatly etc. (thickness of joints except at sharp curve shall not to more than 3 mm), including making drainage opening wherever required complete etc. as approved by the Consultant/ Engineer In-charge. (The length of installed kerb shall be measured to calculate volume for payment).

Providing and fixing factory made precast M35 grade cement concrete solid circular bench including transporting, hoisting (necessary hooks) and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required reinforcement, centering, shuttering complete as directed by Engineer In-charge.

Design, supply and installing of 8 meter length Electrotechnical Boom Barrier of polyester powder coated Aluminum (minimum thickness of polyester powder coating 50 micron) Vertical Mounting, Telescopic Boom & End Supports with Reflectors, built-in LED flashing lights and microprocessor control board, having opening time of 2-3 seconds including additional accessories such as pair of photocell, 3 station push buttons, 2 set of remote receiver and 1 hour battery back-up etc. complete as per approval of Consultant/ Engineer In-charge.

Providing & fixing white river (stone) Pebbles size of 2" to 2.5" dia (5 cm to 6.25 cm), in natural colour at site of work including loading, unloading, carriage etc. and as per direction of Engineer In-charge.

Quintal

Design, supply, fabrication, erection and installation of 2 m × 1.8 m × 3.0 m security cabin made entirely from treated full round bamboo and its component, including wall frame, wall matt, door, window, roof frame, roof matt, decking, flooring, railing, shelves and seating, securely anchored to custom-designed MS ring brackets or holding frames fixed around the column and roof. All bamboo components shall undergo chemical treatment (i.e. Boron or CCA) to protect against water ingress, insect attack, and decay, followed by finishing with an outdoor-grade natural oil or a clear UV-resistant coating. The treated bamboo shall be properly dried and cured in accordance with best practices and the provisions of IS 9096:2006, ensuring long-term resistance to termites, fungi, and environmental exposure. MS brackets and supports shall be rust-protected with zinc primer and synthetic enamel or powder-coated finish. Installation to be completed as per approved architectural design and mock-up sample, ensuring uniform spacing, alignment, and aesthetic quality.

Designing, supplying and fixing 6mm thick Bamboo Mat Board on conforming to IS: 13958–1994 for partition, fixed over suitable framework comprising frames by backing or studding with fasteners or screws etc. complete. All bamboo components shall undergo chemical treatment (i.e. Boron or CCA) to protect against water ingress, insect attack, and decay, followed by finishing with an outdoor-grade natural oil or a clear UV-resistant coating. The treated bamboo shall be properly dried and cured in accordance with best practices and the provisions of IS 9096:2006, ensuring long-term resistance to termites, fungi, and environmental exposure. Installation to be completed as per approved architectural design and mock-up sample, ensuring uniform spacing, alignment, and aesthetic quality.

Design, supply, fabrication, erection and installation of bamboo railing made from seasoned and treated natural bamboo poles. Vertical posts and horizontal handrails shall be constructed using bamboo poles of 75 mm diameter for main members and 40–50 mm diameter for intermediate and decorative members. All bamboo components shall undergo chemical treatment (i.e. Boron or CCA) to protect against water ingress, insect attack, and decay, followed by finishing with an outdoor-grade natural oil or a clear UV-resistant coating. The treated bamboo shall be properly dried and cured in accordance with best practices and the provisions of IS 9096:2006, ensuring long-term resistance to termites, fungi, and environmental exposure. The railing shall be fabricated using traditional lashing techniques with weather-resistant natural/coated r

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

ANGLE VALVE Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (a) 15mm dia nominal bore. Angle Valve : Jaquar , Model No. FUS-CHR-29053

BIB COCK Providing and fixing C.P. brass Bib Cock of approved quality conforming to IS standards and weighing not less than 810 gms. (a) 15mm nominal bore. Bib Cock: Jaquar, Model no. FUS-CHR-29037

TWO WAY BIB COCK Providing and Fixing in position CP brass 2 Way bib cock of approved make and quality, conforming to IS standards and weighin not less that 810 grams, and as approved and directed by the Engineer-in-charge. Two Way Bib Cock : Jaquar, Model no. FUS-CHR-29041

HEALTH FAUCET Providing and fixing 8 mm dia. C.P/ S.S Jet with flexible tube up to 1.2 metre long with S.S. triangular plate to European type W.C. Of quality and make as approved by Engineer-in-charge. Health Faucet : Jaquar, Model no. ALD-CHR-563 GA

Silencio- 75 mm dia.

Providing and fixing square-mouth S.W. Gully Trap class sp-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: (b) 150xl00 mm size p type

Supply & installation of Grease separator made of polyethylene( HD-PE) as per DIN EN 1825; with proven stability of 25 years; for above ground installation with integrated sludge trap and with odor tight maintenance opening of 450 mm dia.; operating side: right/left as per site requirement; with inspection window with wiper; filling device with ball valve ¾" and pressure relief valve; With Ventilation provision; Draining connection, fire hose quick coupling B 2½"; Suction and emptying sump with drain plug socket 1"; Inlet and outlet Dia.: DN 100 Sludge trap capacity: 400 ltr, Grease storage capacity: 200 ltr, Overall Capacity:830 ltr Inlet and outlet dia: DN 100 Make: ACO: Model: LipuJet-P-OD Extension stage 1 Nominal Size: NS 4 (Art No: 3554.64.40)

Providi

ng & laying UPVC under ground drainage pipes & Fittings of Approved make for storm water drains & Sewer lines of following size conforming to IS:15328 to proper level & grade, jointing including providing coupler with solvent cement / welded joints / as per manufacturer's requirement, encasing the pipe alround using cement concrete 1:3:6 complete if required all as per specifictions, drawing and as directed by the E.I.C. item includes Providing and fixing UPVC fittings such as Bendes, Tees & Y, Reducers, Blanking Plugs, Couplers, Adaptors etc For Sewer line and Storm water Drains NOTE:- Cement concrete for encasing shall be paid under relevant item. 200 mm dia. Nominal Bore- SN-8

150 mm dia. Nominal Bore- SN-8

Providing & fixing 110 mm dia PVC Cowl on PVC ventilating pipes and verticals for soil and waste Pipes & Rain water pipes at top level/ terrace level, as specified and required, etc. complete.

Providing and fixing copolymer polypropylene steel reinforced plastic Foot-rests / Steps of approved brand or eq. as per ASTM D - 4101 specification and moulded a 12 mm dia. IS - 1786 grade Fe - 415 steel reinforcing bar and in "U" shape having dimensions 263 x 168 mm and fixing in concrete / wall as shown in the drawing and as directed all complete.

Construction of catchpit chamber of size 600x600mm up to 1000 mm (clear in to in dimension) including excavation, backfilling, watering, soling, compaction, Reinforcement etc. complete. It includes R.C.C work of M-30 for walls, top and bottom slabs, also having 150 mm thick PCC in M-15 at bottom level. It shall be plastered with 15mm thick Plaster with neat coat in CM 1:3 on internal and outside of chamber with 20mm thick sand faced cement plaster in two coat at all sides. Top shall be covered with FRP surface heavy duty recessed cover with 25T capacity with clear opening of 600x600 mm with frame and cover as Mentioned in Drawing. It shall be completed with all respect in ture line level, plumb with neat & clean surface as per coordinated infrastructure detail drawing up to the level of satisfaction.

Construction of inspection/manhole Chamber of size 900x800x1200 mm (clear in to in dimension) including excavation, backfilling, watering, soling, compaction, Reinforcement etc. complete. It includes R.C.C work of M-30 for walls, top and bottom slabs, also having 150 mm thick PCC in M-15 at bottom level. It shall be plastered with 15mm thick Plaster with neat coat in CM 1:3 on internal and outside of chamber with 20mm thick sand faced cement plaster in two coat at all sides. Top shall be covered with FRP surface heavy duty recessed cover with 25T capacity with clear opening of 600x600 mm with frame and cover as Mentioned in Drawing. It shall be completed with all respect in ture line level, plumb with neat & clean surface as per coordinated infrastructure detail drawing up to the level of satisfaction.

Providing and fixing 3 layer PP-R (Poly Propylene Random Copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP-R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. External work (i)PN - 10 Pipe, 50mm OD (SDR-11)

(ii) PN - 10 Pipe, 80 mm OD (SDR-11)

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. For Security OFfice Toilet Capacity : 0.5 KLD

Supply , Installation, Testing and Comissioning of ISO certified company made self contained Drinking Water Cooler with BEE Rated energy efficient hermetic sealed type compressor,non CFC refrigerent suitable for operation on 230V/1pH/50Hz ac supply,Full stainless steel (S304)body and tank , stainless steel water tray,minimum two nos faucets and suitable drainage system complete in all respect with 300mm height MS fabricated and painted plateform. complete in all respect of the following capacity. NABL accredeated / CPRI/ ERDA lab testing reports with OEM certificate must submitted to engineer in charge. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . Cooling capacity 150 Ltr./Hr. and storage capacity 150 Ltrs

DOMESTIC WATER TREATMENT PLANT Supply installation, testing and commissioning of dometic water treatment plant comprising of Pressure sand filter, and softner Plant accrording to input water quality/analysis. Water treatment plant consisting of FRP tank, filter media, resins, brine tank, CPVC SCH 80 piping, isolation valves, instruments supports. The scope shall include CPVC SCH 80 interconnection piping, Butterfly Cast Iron valves, NRV, instruments, autoback wash arrangement, Brine preparation tank & agitator platform, 1 nos Agitator require capacity and Ventury etc.complete the job .Scope shall also includes one month operation including consumable and training for operation of staff. Inlet Flow Range : 50 m3/hour. Input Water Parameters: - As per Site Output Water Hardness : < 50 PPM

WTP FEED PUMP. Centtrifugal Monoblock Transfer pump Supplying, installing, testing and commissioning of centrifugal pumps Complete with SS-316 casing, S.S 316 impeller and SS-316 shaft, C.I. Base CED (Cathode Electrode Deposition) coating & head TEFC motor (with mechanical seal) driven by 415 V AC, 3 phase, 50HZ., motor running at 2900 rpm speed , dry run protection, antivibration paid, 2 pole Motor & IE3 Efficiency, shall be supplied with all accessories viz., base plate, coupling, motor etc. complete. Contractor to submit performance curves and technical catalogue of the proposed model for review and information. Panel mounted microprocessor based multi pump controller with large graphical display with VGA 240 x 320 pixels and IP 55 enclosure, diodes to indicate pump ready, earthing, pump running and fault condition, Cascade Operation. Each incomer and Outgoing feeder should be capable for protection against Overload, Short Circuit and Phase reversal condition and shall be capable to communicate with other controllers following. The PLC shall support MODBUS-IP communication for its compatability to intergrate with 3rd party BAS system. Controller shall authorise Read/Write command via BMS.All alarms should be displayed in the controller. System should be equipped with dry running protection. Indication of all type of faults / on-off status / electrical parameters shall be available on panel and central IBMS monitors. On-off operation for all pumps shall be available on BMS system. SITC of elctronic type low water level controler with LED panel to operate pump (necessary contacts along with minium one PLC operated spare contacts required), shall prevent the pump from dry running Mounting Height : 500mm from the bottom of Raw Water tank. Electronic type low, Medium & High water level controller with LED panel to operate pump (necessary contacts along with minimum one PLC operated spare contacts required),level controller with operational mode as one pump working at Medium level and cut off at High level complete the job. Mounting Height (Medium Level) : (Domestic Treated water Tank) Mounting Height (Hight Level ): (Domestic Treated water Tank) with probe & all control wiring from Pump room Panel to operate the system automatic/manual & shall prevent the pump from dry running. Scope shall also include power and control cable of required size, termination, cable tray from Pump to Control panel, control cable as whereever required etc. complete the job. Set of accessories such as GI C Class headers of suction and discharge for (working and Standby pump assembly) with CED Coating, Gun Metal Isolation valves, Gun Metal non return valves, pressure gauge with Isolation Valve of PN 10 etc. complete the job. Capacity per pump - 40.0 m3/hour, Head - 30 mt, 1 Set = 3 Nos. Pump (2 Working + 1 Standby - cascade operation).

HYDRO PNEUMATIC SYSTEM FOR Domestic Water Distribution, (UGT to OHT water transfer pump) Variable Speed Hydro-booster System Compact self contained Hydro-booster system comprising of following SITC of In-line, vertical multistage, centrifugal clear water pumps with SS-304 casing, S.S 304 impeller and SS-304 shaft, C.I. Base CED (Cathode Electrode Deposition) coating & head TEFC motor (with mechanical seal), dry run protection, antivibration paid, 2 pole Motor & IE3 Efficiency. Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Panel mounted microprocessor based multi pump controller with large graphical display with VGA 240 x 320 pixels and variable frequency drive (VFD) integrated in a single body, pressure sensor transmitter, IP 55 enclosure, diodes to indicate pump ready, earthing, pump running and fault condition, Cascade Operation. Each incomer and Outgoing feeder should be capable for protection against Overload, Short Circuit and Phase reversal condition and shall be capable to communicate with other controllers following. The PLC shall support MODBUS-IP communication for its compatability to intergrate with 3rd party BAS system. Controller shall authorise Read/Write command via BMS.System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equipped with dry running protection. Indication of all type of faults / on-off status / electrical parameters shall be available on panel and central IBMS monitors. On-off operation for all pumps shall be available on BMS system. Electronic type low water level controller with LED panel to operate pump (necessary contacts along with minimum one PLC operated spare contacts required), with probe & all control wiring from Panel to tank to operate the system automatic/manual & shall prevent the pump from dry running. Scope shall also include power and control cable of required size, termination, cable tray from Pump to Control panel, control cable as whereever required etc. complete the job. Pre-charged diaphragm pressure vessel with interchangeable membrane, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc. complete (size of pressure vessel shall be as per manufacturer recommendation). Set of accessories such as GI C Class headers of suction and discharge for (working and Standby pump assembly) with CED Coating, Cast iron control valves, Cast Iron non return valves, pressure transducers, pressure gauge with Isolation Valve of PN 10 etc. complete the job.Require complete company fitted ready-to-connect packaged system. Capacity per pump - 25.0 m3/hour, Head -65 mt, 1 Set = 3 Nos. Pump (2 Working + 1 Standby - cascade operation), Location - UGT Pump Room, Suction head - flooded positive

suction

HYDRO PNEUMATIC SYSTEM FOR Irrigation Water Distribution, Variable Speed Hydro-booster System Compact self contained Hydro-booster system comprising of following SITC of In-line, vertical multistage, centrifugal clear water pumps with SS-304 casing, S.S 304 impeller and SS-304 shaft, C.I. Base CED (Cathode Electrode Deposition) coating & head TEFC motor (with mechanical seal), dry run protection, antivibration paid, 2 pole Motor & IE3 Efficiency. Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Panel mounted microprocessor based multi pump controller with large graphical display with VGA 240 x 320 pixels and variable frequency drive (VFD) integrated in a single body, pressure sensor transmitter, IP 55 enclosure, diodes to indicate pump ready, earthing, pump running and fault condition, Cascade Operation. Each incomer and Outgoing feeder should be capable for protection against Overload, Short Circuit and Phase reversal condition and shall be capable to communicate with other controllers following. The PLC shall support MODBUS-IP communication for its compatability to intergrate with 3rd party BAS system. Controller shall authorise Read/Write command via BMS.System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equipped with dry running protection. Indication of all type of faults / on-off status / electrical parameters shall be available on panel and central IBMS monitors. On-off operation for all pumps shall be available on BMS system. Electronic type low water level controller with LED panel to operate pump (necessary contacts along with minimum one PLC operated spare contacts required), with probe & all control wiring from Panel to tank to operate the system automatic/manual & shall prevent the pump from dry running. Scope shall also include power and control cable of required size, termination, cable tray from Pump to Control panel, control cable as whereever required etc. complete the job. Pre-charged diaphragm pressure vessel with interchangeable membrane, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc. complete (size of pressure vessel shall be as per manufacturer recommendation). Set of accessories such as GI C Class headers of suction and discharge for (working and Standby pump assembly) with CED Coating, Cast iron control valves, Cast Iron non return valves, pressure transducers, pressure gauge with Isolation Valve of PN 10 etc. complete the job.Require complete company fitted ready-to-connect packaged system. Capacity per pump - 15.0 m3/hour, Head -50 mt, 1 Set = 3 Nos. Pump (2 Working + 1 Standby - cascade operation), Location - STP Pump Room, Suction head - Nagative suction

Package type STP - 24 KLD Supplying, installing, testing & commisioning of STP, deatils as per below mentioned: Following are the various components of the proposed Packaged STP process. Each component has a distinct role in the treatment process. 1. Primary Treatment: Pre-treatment removes material that can be easily collected from the raw sewage prior to damaging or clogging the sewage/pump lines of clarifiers like tree limbs, trash, leaves branches etc. where in the influent sewage water passes through a bar screen which removes inorganic materials like plastic packets, sticks cans etc carried in the sewage stream. Solid Separation Zone: First stage transforms the solids in raw sewage to settled solids while allowing scum to Float on the surface. It is a primary sedimentation zone in which settled sludge is stabilized by anaerobic digestion with a BOD removal of 30-40% Anoxic Zone: Anoxic zone accomplishes denitrification of the wastewater stream. Denitrification process includes anoxic microbes which break down existing nitrates, which results in the release of inert nitrogen gas into the atmosphere. Due to Dissolved oxygen level between 0.2 to 0.5 ppm in the anoxic zone free ammonia is achieved as per NGT norms. 2. Secondary Treatment: Aeration Zone: The sewage from anoxic zone flows to the aeration zone. Air is diffused with help of air blowers which will encourage the growth of bacteria cultures in and around the floating plastic media inside the aeration zone. The PP media provides extended surface area for growth of microorganism with a BOD removal of approx. 60-65%. Sedimentation Zone: The next step of treatment involves the sedimentation where organic wastes are settled in the sedimentation zone. The settled waste in the bottom of the tank is pumped back to the solid separation as a return sludge, to ensure that quality of effluent would pass the stipulated sewage parameters. 3. Tertiary Treatment: The secondary treated sewage is then passed through Pressure Sand Filter where in suspended solid is removed around 90-95%, Activated Carbon Filter helps in further removal of color & odor. The treated water is then disinfected using Chlorine Dosing system which is a disinfection process, which in turn supports in further reduction of BOD levels before reuse.

Package type STP - 36 KLD Supplying, installing, testing & commisioning of STP, deatils as per below mentioned: Following are the various components of the proposed Packaged STP process. Each component has a distinct role in the treatment process. 1. Primary Treatment: Pre-treatment removes material that can be easily collected from the raw sewage prior to damaging or clogging the sewage/pump lines of clarifiers like tree limbs, trash, leaves branches etc. where in the influent sewage water passes through a bar screen which removes inorganic materials like plastic packets, sticks cans etc carried in the sewage stream. Solid Separation Zone: First stage transforms the solids in raw sewage to settled solids while allowing scum to Float on the surface. It is a primary sedimentation zone in which settled sludge is stabilized by anaerobic digestion with a BOD removal of 30-40% Anoxic Zone: Anoxic zone accomplishes denitrification of the wastewater stream. Denitrification process includes anoxic microbes which break down existing nitrates, which results in the release of inert nitrogen gas into the atmosphere. Due to Dissolved oxygen level between 0.2 to 0.5 ppm in the anoxic zone free ammonia is achieved as per NGT norms. 2. Secondary Treatment: Aeration Zone: The sewage from anoxic zone flows to the aeration zone. Air is diffused with help of air blowers which will encourage the growth of bacteria cultures in and around the floating plastic media inside the aeration zone. The PP media provides extended surface area for growth of microorganism with a BOD removal of approx. 60-65%. Sedimentation Zone: The next step of treatment involves the sedimentation where organic wastes are settled in the sedimentation zone. The settled waste in the bottom of the tank is pumped back to the solid separation as a return sludge, to ensure that quality of effluent would pass the stipulated sewage parameters. 3. Tertiary Treatment: The secondary treated sewage is then passed through Pressure Sand Filter where in suspended solid is removed around 90-95%, Activated Carbon Filter helps in further removal of color & odor. The treated water is then disinfected using Chlorine Dosing system which is a disinfection process, which in turn supports in further reduction of BOD levels before reuse.

Plant Room Sump Drain Pump Supply, installation, testing & commissioning of Submersible Non Clog, single stage, single entry pumps connected to TEFC submersible motor for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe. The pump shall be provided with a lifting devise of pull chain/guide rail. (Pumps suitable to handle solids upto 20 mm size with C.I. body, SS304 shaft, SS impeller). Panel mounted microprocessor based multi pump controller with large graphical display with VGA 240 x 320 pixels and IP 55 enclosure, diodes to indicate pump ready, earthing, pump running and fault condition, Cascade Operation.

Each incomer and Outgoing feeder should be capable for protection against Overload, Short Circuit and Phase reversal condition and shall be capable to communicate with other controllers following. The PLC shall support MODBUS-IP communication for its compatability to intergrate with 3rd party BAS system. Controller shall authorise Read/Write command via BMS.All alarms should be displayed in the controller. System should be equipped with dry running protection. Indication of all type of faults / on-off status / electrical parameters shall be available on panel and central IBMS monitors. On-off operation for all pumps shall be available on BMS system.Scope shall also include supply, laying, termination of control and power cables of adequate size and arrangemnt of cable trayfrom pump to control panel etc. to complete the job. Electronic type low, Medium & High water level controller with LED panel to operate pump (necessary contacts along with minimum one PLC operated spare contacts required),level controller with operational mode as one pump working at Medium level, both pumps at High level with a hooter alarm and cut off at Low level complete the job. Mounting Height (Low Level ): (Sump) Mounting Height (Medium Level) : (Sump) Mounting Height (Hight Level ): (Sump) with probe & all control wiring from Pump room Panel to Sump to operate the system automatic/manual & shall prevent the pump from dry running. Scope shall also include power and control cable of required size, termination, cable tray from Pump to Control panel, control cable as whereever required etc. complete the job. Set of accessories such as CPVC SCH 80 headers of discharge for (working and Standby pump assembly) , Gun Metal Isolation valves, Gun Metal non return valves, pressure gauge with Isolation Valve of PN 10 etc. complete the job. Capacity per pump - 10.0 m3/hour, Head -20 mt, 1 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade operation).

Providing Supplying And Fixing Of Organic Waste Converter Of Capacity Of 500Kg/Day.Technical Specification Of System:- Organic Waste Machine Or Composting Machines To Be Used To Effectively Dispose Of Organic Wastes (Food Waste And Similar Biodegradable Wastes) In Vegetable, Fruits, Kitchen Waste Etc. The Unit Can Efficiently Treat Organic Waste Resulting In Volume Reduction Of Upto 90% And Convert The Residual Material Into High Quality Compost. This Fully Automated Composting Machine Can Be Used Onsite And Is Capable Of Reducing Solid Waste From Food Sources, Marine Products And Agriculture Resources Into High Quality Compost In An Eco-Friendly Manner. The End Product I.E High Quality Compost Can Be Used For Horticulture/Gardening. Owc Machine Composter Is Fully Automatic And Compact In Size, Housing With Epoxy Painted And Composite Reactor Tank Material (Blades, Shaft, Input & Output Door) Shall Be Of Stainless Steel-304 Grade, Processes All Types Of Organic Waste, Noiseless, Odourless, Maintenance-Free, No Harmful Gases Let Out, No Pathogens And Does Not Need A Skilled Person To Operate It. The Minimum Requirement Is As Shrader Inbuilt (5 Hp) Helical Gearbox, Mixer Motor 7.5 Hp With Planetary Gearbox, Blower 2.5 Hp Min., External Body Shall Be In M.S Plate With Paint, Machine Heating System Shall Be With 50Kw Ceramic Coil. Machine Dimension 4.50 Mtr X1.80 Mtr X 2.0Mtr. Overall Space For Operation Of 1200Kg Per Day Owc Shall Be 7.50Mtr X 7.50Mtr X 3.60 Mtr (Lxwxh) With Required Base Support Foundation, Frp Shed, Incoming Power Cable With Mccb Suitable For 61Kw Power Rating. (This Power Connection , Foundation And Frp Shed Work In Civil Contractor’S Scope.) Panel For Auto Operation Of Owc In Owc Supplier Scope. This Organic Waste Converter Can Efficiently Mix Organic Waste And Convert The Same Into Compost. This Fully Automated Composting Machine Can Be Used On-Site And Is Capable Of Reducing Solid Waste From Food Sources, Marine Products And Agriculture Resources Into High Quality Compost In An Eco- Friendly Manner. The Unit Is A Fully Enclosed Automatic Composting Machine That Disposes Of Any Food Matter. A Rotating Arm Inside The Machine Slowly Churns The Waste Food To Constantly Mix The Organic Waste The Process Is A Practical Alternative To Traditional Waste Disposal. The Composting Machine Is Designed For All Types Of Cooked And Uncooked Vegetables, Fruits, Fish, Poultry And Meat Products, Dairy, Wheat, Flour, Rice, Tea, Coffee, Grass Clippings, Leaves And All Such Types Of Processed And Unprocessed Biodegradable Waste. The Composting Process Takes Place In A Closed Composting Barrel, Preventing Any External Handling Or Contamination, While Eliminating Any Sources Of Food For Insects And Rodents. The Composters Are Sealed To Prevent Odors To Be Released, Eliminating In This Way A Common Nuisance And Source Of Public Complaints Frequent In Open Air Or Traditional Composting Sites. This Composter Is Designed And Manufactured According To The Toughest Industry Standards. High Quality Materials And Components Coupled With A Responsive Technical After Sales Team Provide A Lo

ng Service Life And Faultless Reliability. Make:- Kelvin/Ecs/EcobotSalient Features And Advantages.•Fully Automatic And Compact In Size., •All Contact Parts Are In Stainless Steel Construction.•Processes All Types Of Organic Waste (Canteen Waste, Kitchen Waste And Garden Waste).•Volume Reduction Of Organic Waste Into High Quality Compost.•Ready Compost In 24 Hours.•Noiseless, Odorless, Maintenance-Free.•No Harmful Gases.•No Pathogens.•Reduces Large Amounts Spent On Transportation To Landfill Sites.•In-House Waste Management Reducing Dependence On Any Outside Agency.•Segregation And Separation Of The Organic Waste.•Inbuilt Shredding Of The Organic Waste While Feeding In The Composter.•Processing In The Composter.•Finished Ready Compost For Use. Inclusive-•Unloading And Placement The Machine At Installation Site.•Installation, Testing And Commissioning Of Machine.Mode Of Measurements:The Rate Shall Include The Cost Of All Materials, Labours Etc. Complete As Specified In The Item. The Rate Shall Be Measured In No. Basis. Civil Work, Frp Shed And Incoming Power Cable With Mccb Is Not Included In This Line Item.

LT PANEL (NON TTA) Supply, installation, testing and commissioning of 3 phase 415V 4 wire Free Standing Floor mounted LT panel made out of minimum 14 SWG CRCA sheet after seventank process and painting with Epoxy powder coating including all switchgear as detailed below. The panel having PU/Neoprene rubber gasket of not less than 3mm thickness,separate detachable, gland plate M.S. base channel, hinged door with locking arrangement for equipment/switchgear. The panel shall consist of suitable rating FP/TPN Aluminium- busbar-as per SLD (at the rating of 0.8ASq.mm) supported with DMC/ SMC barriers and colour coded with Heat shrinkable sleeves. The Metering shall be provided as specified. The panel shall have Short circuit with standing capacity as given in SLD and consist of the switchgear as mentioned below. The panel shall be mounted on plinth, stand, etc. including all materials. The panel shall be got fabricated from manufacturers with CPRI Test certificate only. All the Panels shall have minimum 25% outgoing as per SLD. The earth bus shall be continuoulsy run without any jointing/welding and its Size should be per SLD. The size of all Panel Mounting Meters shall be 96X96mm.The Panels shall be mounted on U channels including supply and fixing of the same. MCBs shall be provided for Control purposes. (All Panels shall be extendable type only). Price shall be inclusive following: Shifting of panels from site store to the suitable location. Installation of panel as located in electrical drawings or as per site conditions, including removing packing etc. Earthing all components, frame etc. to a

common internal earth bar. Connection, testing & commissioning. Electrical contractor shall carry out the insulation test at site & all the readings shall be submitted in copy to the consultant or engineer-in-charge. Supply, installation, testing and commissioning all accessories, supporting structure, hard ware etc to complete the job. Supply, installation, testing and commissioning of necessary tools, hard ware, testing hard ware, testing equipment etc. The rates for the distribution boards apart from the Breakers and instruments shall also include the following : This schedule of Quantities shall be read in conjuction with the technical specification, General & Special conditions as well as all tender drawings. Supporting rigid steel framework. Cubicle type, 14 gauge CRCA sheet steel enclosed. Proper bonding to earth. Painting/lettering on Breakers and distribution boards, the location they serve, providing on each panel its circuit diagram. Providing cable clamps / supports within distribution boards cable alley. All MCB’s shall be of minimum 10 KA breaking capacity. The breaking capacity of MCCB’s are mentioned panel wise. All MCCB’s shall be with thermal magnetic releases upto 250 amps and miroprocessor based for 250 amps and above capacity, unless specified otherwise. All motor feeders MCCBs shall be of motor duty. Distribution panels shall be Powder Coated with Siemens gray paint shade no. RAL-7032 of IS-5. Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993. IP 4x for all Indoor panel. IP 65 and double door for all outdoor panel. All MCCB’s shall be provided with operating mechanism for door interlock. All measuring instruments (Meters) shall be of digital electronic with LED of approved make. All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire. All panels shall have provision of the following: Pad locking of Switch board doors.All MCB’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic and discharge lamps and UPS etc. shall be of type D characteristic. All incoming and outgoing air circuit breakers shall be placed on middle portion of the vertical in single tier formation. SPD as shown in SLD (REFER TENDER SLD FOR DETAIL BOQ) COMMON UTILITY PANEL LOCATED AT CAFETERIA SERVICE ROOM

FSP-FEEDER SECTION PILLER (OUTDOOR TYPE) LOCATED NEAR SUBSTATION

PLUMBING PANEL LOCATED IN PUMP ROOM

EXTERNAL LIGHTING PANEL-1 (OUTDOOR TYPE)

EXTERNAL LIGHTING PANEL-2 (OUTDOOR TYPE)

SECTION FEEDER PANEL LOCATED IN EACH BLOCK METER ROOM

Supply, installation, testing and commissioning of Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for SPNDB (c) 12 Way + 12 Module

SPNDB (c) 08 Way + 08 Module

TPNDB (c) 8 Way 8+24 Module

TPNDB (d) 12 Way 8+36 Module

VTPN DB 4 way (8 + 12), Double door

VTPN DB 8 way (8 + 24), Double door

VTPN DB 12 way (8 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 6-32 Amp SP MCB

6-32 Amp DP MCB

40 Amp DP MCB

6-32 Amp TP MCB

40 Amp TP MCB

6-32 Amp FP MCB

40 Amp FP MCB

50-63 Amp FP MCB

80-100 Amp FP MCCB

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying fitting and fixing of (RCCBs) of the following Amp capacity 25 Amp DP RCCB 30mA

40 Amp DP RCCB 30mA

40 Amp FP RCCB 30mA

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. Supply ,fixing, connection and testing of MCCBs with enclouser and all accessories to complete the job. 25/32A DP MCB with Enclouser

Supply ,fixing, connection and testing of MCCBs with enclouser and all accessories to complete the job. 40A DP MCB with Enclouser

Supply ,fixing, connection and testing of MCCBs with enclouser and all accessories to complete the job. 40A FP MCB with Enclouser

Supply ,fixing, connection and testing of MCCBs with enclouser and all accessories to complete the job. 63A FP MCB with Enclouser

Supply ,fixing, connection and testing of MCCBs with enclouser and all accessories to complete the job. 100A FP MCCB with Enclouser

Supply ,fixing, connection and testing of ATS with enclouser and all accessories to complete the job. 32A DP ATS with Enclouser

Supply, connection, testing and commissioning of heavy duty, medium voltage,XLPE (IS 7098 - PART-II) insulated, Stranded AL / Cu conductor Armoured / Flexible FRLS cables as per specification & IS. The cable shall have outer sheeth of XLPE and inner sheath of PVC with stranded AL conductor wherever specified. The cable shall be laid underground in excavated trench / prepared trench / hume pipes when laid outside the building. Cable shall be laid throught preapred trench / cable tray / duct / hume pipe / channel / floor trunks etc when laid inside the building as instructed by PMC/Site Incharge. 3.5C x 300 Sq.mm. Aluminum XLPE armoured cable

Meter

3.5C x 240 Sq.mm. Aluminum XLPE armoured cable

3.5C x 120 Sq.mm. Aluminum XLPE armoured cable

3.5C x 95 Sq.mm. Aluminum XLPE armoured cable

3.5C x 70 Sq.mm. Aluminum XLPE armoured cable

.5C x 50 Sq.mm. Aluminum XLPE armoured cable

3.5C x 35 Sq.mm. Aluminum XLPE armoured cable

3.5C x 25 Sq.mm. Aluminum XLPE armoured cable

4C x 16 Sq.mm. CU XLPE armoured cable

4C x 10 Sq.mm. CU XLPE armoured cable

4C x 6 Sq.mm. CU XLPE armoured cable

4C x 4 Sq.mm. CU XLPE armoured cable

4C x 2.5 Sq.mm. CU XLPE armoured cable

3C x 10 Sq.mm. CU XLPE armoured cable

3C x 6 Sq.mm. CU XLPE armoured cable

3C x 4 Sq.mm. CU XLPE armoured cable

3C x 2.5 Sq.mm. CU XLPE armoured cable

Providing, supplying of Multicore cables including carriage testing of the following sizes PVC insulated and FR PVC round Sheathed, Copper conductor flexible cable 1100Volt confirming to IS694 3C x 2.5 Sq.mm. CU XLPE flexible cable

3C x 4.0 Sq.mm. CU XLPE flexible cable

3C x 6 Sq.mm. CU XLPE flexible cable

4C x 4 Sq.mm. CU XLPE flexible cable

4C x 10 Sq.mm. CU XLPE flexible cable

4C x 16 Sq.mm. CU XLPE flexible cable

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5C x 25 sq. mm (28mm)

3.5C x 35 sq. mm (32mm)

3.5C x 50 sq. mm (32mm)

3.5C x 70 sq. mm (38mm)

3.5C x 95 sq. mm (45mm)

3.5C x 120 sq. mm (45mm)

3.5C x 240 sq. mm (45mm)

3.5C x 300 sq. mm (45mm)

Supplying and making end termination with brass compression gland and Copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required. 3/4 X 2.5 sq. mm (15mm)

3/4 X 4 sq. mm (17mm)

3/4 X 6 sq. mm (19mm)

3/4 X 10 sq. mm (22mm)

3/4 X 16 sq. mm (28mm)

Concealed wiring in looping in system with 2x1.5 sqmm PVC insulated single core cable of 600V grade in heavy gauge PVC pipe including occuping and fitting of elbows, bend, fees, junction boxes etc including required size of MS concealed boxes and front plate for housing of switches, sockets fan regulator, bell push etc complete to light point.

Point

Wiring as in item No.20 above to Light Plug Point when fixed elsewhere with continous earth wire complete

Wiring as in item No.20 above for Staircase/2Way Switch Wiring

Loop light point controlled by same switch or SP MCB (group-c)

Wiring in looping in system with 1.5 sqmm PVC wire in heavy gauge 16SWG 3/4 inch dia MS conduit pipe Including supplying and fitting of bends, tees, joints Boxes etc as necessary complete with 5amp FT switch ceiling rose etc including earthing the conduit to light point.

Wiring as in item No. 29 Complete to a Light Plug Point when fixed elsewhere.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

2 way 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, onnection, painting etc. as required.

wiring as in item No.20 above to Power Plug Point with 2x4mm2 incluJing supplying and fitting of l5Amp modular switch. socket Combined with coniinuous earth wire to a Power Plug Point Complete'

Wiring as in item No.20 above to Ceiling Fan/Exhaust Fan Point

iiing as in item No.20 above to Wall Point

Circuit/sub-man wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire

Circuit/sub-man wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire

Circuit/sub-man wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Circuit/sub-man wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supply, installation, testing and commissioning of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm

Supply, installation, testing and commissioning of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32mm

Supply, installation, testing and commissioning of 16 A x 240 V plug & socket with IP55 enclosure.

Supply, installation, testing and commissioning of 32 A TP Isolator with IP55 enclosure.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.l. suspenders including G.l. bolts & nuts, etc. as required. 150mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (Galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.l. suspenders including G.l. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (Galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.l. suspenders including G.l. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member" (Galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.l. suspenders including G.l. bolts & nuts, etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required. 160 mm dia (OD-160 mm & ID-135 mm nominal)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required. 200 mm dia (OD-200 mm & ID-175 mm nominal)

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required 150 mm dia

plying, installation, testing and commissioning of ON LINE UPS system with SMF battery and 30 min back and with battery rack complete in all respect. 1 set. of 10 KVA UPS three phase input & three phase output for unbalance load.

S/L SWG GI wire in ground: Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required

Supply of CPRI tested maintenance free ,Low carbon mild steel copper coated earth rod of 3 metre electrode having diameter of 17.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 with threaded top with 1 mtr length seperate rod of same dia size with thread at both end with female threaded socket for joining both rods , universal clamp made of SS to connect rod with flat conductor. Earth conductivity enhancing compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested. The above arrangements shall be provided with Heavy duty earth chamber of 5000kg load bearing capacity having rust proof heavy duty weather proof Polyethylene material with following dimensions :254 mm dia (top), 330 mm dia (bottom) & 260mm (height) to ensure the safety of earthing system

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and fixing Earthing Strip of 50x6mm Hot Dip Galvanized GI strip

Providing and fixing Equipotential Busbar of 50x6mm Hot Dip Galvanized iron.

Fixing of Shock Treatment Charts written in English and Local Language. These charts shall be framed in teak wood frame and covered with glass.

Supply and fixing in position the best quality Danger Boards of approved shape and size as specified by Local Electricity Authorities written in English & Local Languages.

Supply and fixing in position 1000 mm wide rubber matting of 11KV gradeas per electricity rules.

Supply and fixing in position 1000 mm wide rubber matting of 1.1KV grade as per electricity rules.

Supply and fixing in position the approved single line diagram framed in 1000 x 800 mm size glass frame in the sub station.

Supply of tool kit with 1 pair 11KV rubber hand gloves

Supply of first aid box of approved make as per specification.

HIGH MAST POLE - 12 METER Supplying, erecting, testing, commissioning approved make M.S. Polygonal High Mast Pole having following general Specification. (a) Polygonal Section fabricated from M.S. Plate confirms BSEN 10025 & Hot deep galvanized minimum 65/86 micron (as per IS 2629 /1985) Lantern carriage with ring and rubber lines for erection of luminaries of suitable site. (b) Maximum telescopic section not more than four (c) Double drum gear pipe motorized winch with 6mm dia S.S. Rod (For 16 mtr and above size) (d) Approved make L.E.D. aviation light = 1 No. Lightening arrestor = 1 No. with necessary wiring of 2.5 sq.mm 5 core ISI copper cable Unarmoured. (e) Bottom most section suitable for mounting reversible motor and switchgears having door not more than 1400mm x 300mm with waterproof gasket & hinges & locking arrangement. (f) Pole structure comprises suitable size of reversible motor, cable and necessary switchgears with control panel. (g) bottom section shall have suitable size of thickness supports ribs foundation bolts nuts etc. (h) Item not comprises the cost of lanterns. (i) Necessary Cement Concrete foundation as per IS including testing & commissioning of the entire structure for following size of High Mast poles [1] High Mast 12 Mtr. TOP A/F 105 mm, BOTTOM A/F 360mm, No. of Sec. No. - 1, Bottom Thickness - 3 mm, Size of Base Plate - Dia 520 mm x 20 mm thick, Foundation Bolt Size M24 x 850 mm, Qty - 6 Nos., Suitable for mounting Fitting of Light - 6 Nos. this includes all the accessories like trailing cable etc. to complete this job.

ixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)

SHRUB UP LIGHTER (SPIKE) - 6W SITC of LED uplighter of 6W,inbuilt Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current, minimum IP65, minimum IK006 protection,CRI > 70,voltage input AC100-240V.Body-Die-casting AL with Surface Anti-ageing electrostatic spray processing & screen. Estimated Lifetime-L70 @ 50,000hours minimum Light fixture shall be with minimum following specification. 1. High End Lens for better uniformity and low glare for Superior distribution 2. Internal metallic isolated driver for ensuring better reliability and safety. 10KV/5KVA external surge arrestor 3. Fixture along with Driver should be warrantied for 5yrs And Life is 50,000 hrs @ L70 4. Approved Led source Nichia , Cree, Lumileds , Osram Only 5. PF >=0.9 and THD <=10 % (Certificate need to be submitted from NABL Accredited lab), Internal Driver Surge 4KV, 6. The manufacturer should be ISO 9001 -2008 and ISO 14001 -2004 Company 7. Colour temparature shall be 2700K - 3000K (or as per architecture requirement). Body colour of fixture shall be as per architecture requirement Submission of LM80 for LED source & LM79 for Luminaire from NABL Accredited Lab mandatory. Fixture along with Driver should be warrantied for 5yrs(NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)

CEILING SUSPENDED LIGHT (PENDANT LIGHT) - 20W (INDOOR) Supply, Installation, testing & commissioning of suspended light,System Wattage: 20W LED, Driver Integral: Constant Current Input Voltage: 230-240Vac, Frequency: 50-60Hz Operating Voltage: 100-277Vac, Operating Temperature: -15°C~+50°C Light Source: NICHIA, Luminaire efficiency: 85 lm/w CRI (Ra): ≥80, LED Colour Temperature: 3000K Power Supply: Integral, Power Factor: ≥0.95, THD: <10%, Surge Protection: 2.5KV, Efficiency: >85% Colour Temperature: 3000K/4000K (or as per architecture requirement) Luminaire efficiency : 85 lm/W, Light Distribution: Asymmetrical Body: Die-Cast Aluminium, Diffuser: Clear Polycarbonate,, Life: 60,000 hrs, Life: 60,000 hrs . The luminaire is BIS & CE certifications. Submission of LM80 for LED source & LM79 for Luminaire from NABL Accredited Lab mandatory.Fixture along with Driver should be warrantied for 5yrs. (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)

CEILING SUSPENDED LIGHT (LINEAR PENDADNT - 2 METER) - 20W Supply of 20W hanging light point System Wattage: 20W LED, Driver Integral: Constant Current Input Voltage: 230-240Vac, Frequency: 50-60Hz Operating Voltage: 100-277Vac, Operating Temperature: -15°C~+50°C Light Source: NICHIA, Luminaire efficiency: 85 lm/w, Protection class IP65.CRI (Ra): ≥80, LED Colour Temperature: 3000K Power Supply: Integral, Power Factor: ≥0.95, THD: <10%, Surge Protection: 2.5KV, Efficiency: >85% Colour Temperature: 3000K/4000K (or as per architecture requirement) Luminaire efficiency : 85 lm/W, Light Distribution: Asymmetrical Body: Die-Cast Aluminium, Diffuser: Clear Polycarbonate,, Life: 60,000 hrs, Life: 60,000 hrs . The luminaire is BIS & CE certifications. Submission of LM80 for LED source & LM79 for Luminaire from NABL Accredited Lab mandatory.Fixture along with Driver should be warrantied for 5yrs. (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)

MIRROR LIGHT - 9W Supply, Installation, testing & commissioning of Lighting fixtures of approved make suitable for operation at 230V,50Hz complete with housing, ballast, cover and LED lamp with > 100 Lumen/watt efficiency as per Technical specifications CRI should be > 70. Life : 50000 burning hrs with 70% lumen mainteneace. Surge Protection > 2.5Kv for indoor products and > 4Kv for Outdoor products.Colour Temperature: 3000K/4000K (or as per architecture requirement). Input Voltage range : 140V-270V AC for all products and as approved by the Engineer. The light fixtures may vary as per Interior/Architect/Client requirement. Submission of LM80 for LED source & LM79 for Luminaire from NABL Accredited Lab mandatory. (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect

and Engineer incharge after sampling and mock-up before finalization.)

STEP LIGHT (LINEAR / RECTANGULAR) - 6W Supply, Installation, testing & commissioning of compact and robust wall recessed luminaires for illuminating walls and stairs. Diffused light distribution. Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners. ABS plastic installation housing for preparing the recess opening in wall / stairs. Translucent acrylic diffuser. Single cable entrance via M10 cable gland. Protection class IP65. Mechanical resistance IK03. Pure polyester powder coated RAL 9004 Signal black, RAL9007 Grey aluminium, RAL 7016 Anthracite grey, Graphite grey. Colour Temperature: 3000K/4000K (or as per architecture requirement) , Colour rendering index (CRI)>80.LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >80%, Power factor >0.90, THD <10%, Surge protection 2KV. CE & BIS Certified. Inhouse NABL accredited lab. Submission of LM80 for LED source & LM79 for Luminaire from NABL Accredited Lab mandatory. Fixture along with Driver should be warrantied for 5yrs (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)

TREE UPLIGHTER (SPIKE) - 12W SITC of LED uplighter of 12W,inbuilt Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current, minimum IP65, minimum IK006 protection,CRI > 70,voltage input AC100-240V.Body-Die-casting AL with Surface Anti-ageing electrostatic spray processing & screen. Estimated Lifetime-L70 @ 50,000hours minimum Light fixture shall be with minimum following specification. 1. High End Lens for better uniformity and low glare for Superior distribution 2. Internal metallic isolated driver for ensuring better reliability and safety. 10KV/5KVA external surge arrestor 3. Fixture along with Driver should be warrantied for 5yrs And Life is 50,000 hrs @ L70 4. Approved Led source Nichia , Cree, Lumileds , Osram Only 5. PF >=0.9 and THD <=10 % (Certificate need to be submitted from NABL Accredited lab), Internal Driver Surge 4KV, 6. Colour temparature shall be 3000K/4000K (or as per architecture requirement). Body colour of fixture shall be as per architecture requirement Submission of LM80 for LED source & LM79 for Luminaire from NABL Accredited Lab mandatory. (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)

FLOOR RECESSED LIGHT (SLIM RECEESED LED PATH LIGHT) - 3W System Wattage: 3W, Driver Integral: Constant Current Input Voltage: 230-240Vac, Frequency: 50-60 HzOperating Voltage: 100-277VAC, Operating Temperature: -15°C~+50°C Light Source: Osrqam, Lumileds CRI (Ra): >80, LED Colour Temperature: as per Architect Power Supply: Integral, Power Factor: >0.95, THD: <10%, Surge Protection: 2.5KV, Efficiency: >84% Colour Temperature:3000K/4000K (or as per architecture requirement) , Luminire efficiency :85 lm/w, Beam Angle: 15° / 25° / 40° Body: Die-cast Aluminium Alloy, Diffuser: Clear Toughened Glass T=8mm, Loure:- Honey comb Mounting: Flushed , IP-67 , IK09 Front Ring:- 316 Grade Stainless Steel Finish: Graphite Grey/Anthracite Grey/Jet Black, IP66, IK04, Life: 60,000 hrs The luminaire is BIS & CE certifications. (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)(junction box shall be jelly filled IP-67)Submission of LM80 for LED source & LM79 for Luminaire from NABL Accredited Lab mandatory. Fixture along with Driver should be warrantied for 5yrs (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)

fter sampling and mock-up before finalization.)

SINGLE ARM BRACKET STREET LIGHT POLE Supply & Installation of 7M Height pole made of mild steel pipe section 100 x100 with Single Arm Bracket arrangement. The pole to be provided with suitable size base plate. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Min) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. junction box to light point wiring inclusive of 3c x 2.5 sq.mm cu. flexible wire. Pole & it's parts are marine/Saline painted in 3 layer coating(coating thickness-100 microns minimum)in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint -customised colour Metallaic Grey.

DOUBLE ARM BRACKET STREET LIGHT POLE Supply & Installation of 7M Height pole made of mild steel pipe section 100 x100 with Double Arm Bracket arrangement. The pole to be provided with suitable size base plate. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Min) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. junction box to light point wiring inclusive of 3c x 2.5 sq.mm cu. flexible wire. Pole & it's parts are marine/Saline painted in 3 layer coating(coating thickness-100 microns minimum)in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint -customised colour Metallaic Grey

FOCUS LIGHT - 20W Supply, Installation Testing and Commissioning of surface mounted compact spot light designed to provide directional light. Beam angle 15° / 25° / 40°. Luminaire made of extruded aluminium section with inner grooves to fix the top and bottom ring (grade 6063) , pressure die cast aluminium top and bottom ring of high corrosion resistance and non corrosive A2 stainless steel fasteners. Clear toughened glass of 4mm thickness. Pressure die-cast aluminium surface mounting base. Hybrid optics with lens & mirror finish pure aluminium reflector combination for higher efficiency, lower optical losses with optimum glare suppression. Swivel range of 0° - 90°. Single cable entrance M10 cable gland. Protection class IP66. Mechanical resistance IK07. Pure polyester powder coated RAL 9004 Black, RAL9007 Gre

e & LM79 for Luminaire from NABL Accredited Lab mandatory. (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)

POLE LIGHT (BULB VERTICALLY HUNG WITH POLE) - 12W Supply, Installation, testing & commissioning of 12W Bulb,System Wattage: 12W LED,IP65 Driver Integral: Constant Current Input Voltage: 230-240Vac, Frequency: 50-60Hz Operating Voltage: 100-277Vac, Operating Temperature: -15°C~+50°C Light Source: NICHIA, Luminaire efficiency: 85 lm/w CRI (Ra): ≥80, LED Colour Temperature: 3000K Power Supply: Integral, Power Factor: ≥0.95, THD: <10%, Surge Protection: 2.5KV, Efficiency: >85% Colour Temperature: 3000K/4000K (or as per architecture requirement) Luminaire efficiency : 85 lm/W, Light Distribution: Asymmetrical Diffuser: Clear Polycarbonate,, Life: 60,000 hrs, Life: 60,000 hrs . The luminaire is BIS & CE certifications. Submission of LM80 for LED source & LM79 for Luminaire from NABL Accredited Lab mandatory. Fixture along with Driver should be warrantied for 5yrs. (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the architect and Engineer incharge after sampling and mock-up before finalization.)

Supplying and fitting of ceiling fan AC Operated type 220/250 volt. Complete with 3nos. Of blades down rod canopy hanging shackle & 30mm length of down rod supplied with the fan by the dealer but the extra length will be charged @Rs25.00/mtrs. (b) Ac ceiling Fan '1200'mm Sweeps

Supplying and fixing of Wall/Table Fan with all necessary attachments and accessories as required. (b) 400mm Wall Fan

Supplying and fitting of exhaust fan double bearing self lubricating type single phase 50hz 250v AC operated complete with supporting frame, fan blades,nuts and bolts and other petty accessories as required. (v) Metal Exhaust Fan 300mm

Supply and application of intumescent based coating on cables/ cable tray using Hilti CP 678 or equivalent make, firestop cable coating of HILTI make or equivalent .The coating shall have a density in the range of 1.2 to 1.4 Kg/ L. The coating shall be non-toxic, asbestos and halogen free and shall have good mechanical strength. The coating shall comply with IEC 332 part 3 (1992).

Sqmtr.

Fire stop mortar system Supply and installation of Fire stop mortar system equivalent to Hilti CP 636 , with minimum 2 hours fire rating when tested in accordance with UL 1479/ASTM-E 814 standards, for horizontal openings in floors or slabs after passing service lines like cables/cable bundles, cable trays etc. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-hi

story method and VERTEQII for seismic zone 4. The product shall be age tested as per Dafstb and DIBT standards. The product shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The product shall be age tested as per Dafstb and DIBT standards.The system shall be UL listed. The gaps around inaccessible or complicated openings shall be sealed with exapnding firestop foam.

Firestop Sealant Supply and installatio of firestop sealant around combustible penetrations like plastic pipes or ducts/pipes with insulation passing through floor to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814. The sealant shall have surface burning characteristics according UL 723 (ASTM E84-96): Flame spread index 0 and smoke development index 5. The sound transmission classification according to ASTM E 90-99 shall be 56 (STC Rating). Sealant shall have mold and mildew resistance and the performance shall be Class 0 according to ASTM G-21. Movement capability approx.. 5% (ISO 11600) and the average volume shrinkage is 24% according ASTM C1241. Sealnt shall meet LEED requirements for indoor environmental quality credit (4.1 and 4.2) with a VOC content of 9 g/l. Seismic tested on mechanical performance, smoke and fire-ratings. The product shall be age tested as per Dafstb and DIBT standards.The system shall be UL listed & classified and product shall bear the UL and FM approval logo on the packing. If none of UL test certificate comply with actual application, an EJ document (as per IFC Guidelines) prepared by a qualified personnel and based on nearest third party tested & approved systems like UL test certificates & in accordance with IFC guidelines shall be producted by manufacturer. A firestop submittal shall be produced by manufacturer , in accordance with approved passive fire protection method statement, for technical approval. Firestop installation shall be done by manufacturer's Accredited Firestop Speciality Contractor and in accordance with manufacturer'sguidelines and UL system test certificates or approved EJ document. Firestop Speciality Contractor needs to submitt work completition certificate along with installation report through manufacturer's documentation Software for periodic inspection & maintenance purpose.

Fire Stop Foam Supply and installtion of expanding firestop foam equivalent to Hilti CP 620 on both sides of wall, with minimum 2 hours fire rating when tested in accordance with UL 1479/ASTM-E 814, for horizontal openings in floors or slabs made of concrete/ masonry or Gypsum after passing service lines like cable trays or cables/cable bundles. The expanding foam expands seven times its volume to fill the cavity at the time of dispensing the material and shall fully cure within two minutes after dispensing. The product shall be age tested as per Dafstb and DIBT standards. The product shall provide water tightness when tested for W rating as per UL standards and shall carry test certificate for sound insualtion of 50 db when tested in accordance with ASTM E 90. The product shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96 and shall have a VOC content of approx. 1.3 g/l as per LEED 2009. The product shall be tested in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. The system shall be UL listed & classified. The system shall be UL & FM approved.

EV Charging Station (CAR) Supply, installation, testing and commissioning of wall mounted/floor standing fast charging station for car with two numbers of combine charging socket as mentioned below with all require components and accessories to finish the job.Require solution for Payment gateway and related software (Charging management software) shall be part of scope. All require components and accessories to operate setisfactory shall be part of contractor's scope.earthing and its terminations should be included in its rate. Fast DC Charger (80KW EV Charger having Dual CCS2 Guns, Gun Capacity: 200 Amps)

Supply, Transportation, Installation, testing and commissioning of IP 66/69 weather proof Outdoor type junction boxes with terminal SIZE-110(L) x 110(B) x 67(D)

Supply, Transportation, Installation, testing and commissioning of IP 66/69 weather proof Outdoor type junction boxes with terminal SIZE-140(L) x 140(B) x 79(D)

Supply, Transportation, Installation, testing and commissioning of IP 66/69 weather proof Outdoor type junction boxes with terminal SIZE-182(L) x 180(B) x 111(D)

Supply, Transportation, Installation, testing and commissioning of IP 66 weather proof Outdoor type junction boxes with terminal (for driver) SIZE-205(L) x 255(B) x 112(D)

Designing, Supply, installation ,Testing & Commissioning of structurally Integrated lightning protection system confirming to IS/IEC 62305-3,NBC 2016 and IS 3043. includes following items/consider as per drawing : 1. 8 sq. mm AL conductor including fixing including clamp, expansion Joints 2. Vertical Air terminals (1 or 3 Mtr.) 3. lightning counter including fixing with clamp - 4. Expansion joint , splicers for conductor including fixing with clamp - 5. Stainless steel 304 GRADE of polyamide /stainless/ brass holder for fixing the aluminum downconductor on ring - 6. Stainless steel 304 GRADE Universal T connector for 8 mm Aluminium Round Conductor to connect with mesh on roof slope - 7. 10 mm dia copper. bonded down conductor including fixing including clamp, expansion Joints 8. Bonding /Rebar Clamp suitable for 32 mm dia for interconnecting round conductor with reinforcement inside the concrete for structural earthing system should be tested for conditioning, Ageing Test & Lightning impulse current withstand test: 100 kA of 10/350µs waveform 9. Cross Splicer for 8 mm & 10 mm conductor 10. Earthing stud of dimension SS-75mm OD plate with 10mm dia tail connector used in structural steel ring earthing system to meet the requirements of IS/IEC 62305 9. Disconnection link for 8 mm aluminium conductor 10. connector -To connect air terminal 8-10 mm with earth fixing point to meet the requirements of IS/IEC 62305 11. 10mm dia copper bonded from AL Conductor to the earth pit station and further the same strip shall be used for interconnecting all the earth pits below ground leve Zinc coating with holder 12. Electrode Cu Bonded Steel Rod 14.2mm dia x 3000mm-(250Microns);Eco Friendly rust proof heavy duty weather proof Polyethylene Earth Pit Chamber with followingdimensions :254 mm dia (top), 330 mm dia (bottom) & 260mm (height);14.2 / OD SS Clamp Both Side; Carbon based backfillcompound - 25Kg Also, Any other Item Not included above but required to complete the Job. Quantities of above items are considered as per Tender drawings.

Supply, Installation, Testing and Commissioning of Microprocessor based Networkable Analogue Addressable Fire Alarm Control Panel. The Panel shall be compliant with EN54-2, EN54-4 and approved by LPCB. The Fire Alarm Control Panel shall have inbuilt one loop. The Panel must have large graphic display. The Panel must also have the capability to take Addressable Intelligent Wired and Wireless Devices on same loop. Each loop shall have a capacity of 127 analogue Addressable devices and 127 Base sounders/Base Sounder Beacons. The Panel shall have 240 V AC power supply along with automatic Battery Charger. Non-Networkable. Approved by LPCB

Supply, Installation, Testing and Commissioning of Active Repeater Panel to be integrated with Fire Alarm Control Panel, larger display Full colour 800 x 480 LCD with resistive touch screen and automatic back-light dimming and the status of any Fire/Fault of Integrated Fire Alarm Panels, Panel should compliant with EN54-2, EN54-4 and Approved by LPCB

Supply, Installation, Testing and Commissioning of Network Module. The Module shall connect Panels and Repeator Panels through RS485. The Module shall use RS485 data at a Baud rate of 115200 Bauds. The Network Module must be configured Master/Slave, Multiple Master/Slave and Peer to Peer networking

Supply, Installation, Testi

Supply, Installation, Testing and commissioning of sensor common mounting base, includes stainless steel contacts, slim profile - only 8mm, quick connection via square cable clamps, facility for remote indicator, Approved by LPCB

Supply, Installation, Testing and commissioning of sensor common mounting base, Features integral Short-Circuit isolator, slim profile, Approved by LPCB

Supply, Laying and Fixing of 2 Core X 1.5 Sq.mm FRLS Multistrand PVC insulated Copper armoured RED cable with all required accessories.

Supply, Installation, Testing and Commissioning of IP based 4MP resolution Dome Camera, Vandal Proof, 2.8mm Lens, Fixed Iris, horizontal field of view:110°,Vertical: 77.6°, 30M IR, Shutter Speed 1 s to 1/100,000 s, DC12V/PoE, IP67/IK10, Basic IVA, Image sensor- 1 / 2.7" CMOS, Effective Pixels 2560 × 1440, Min. Illumination Color: 0.01 Lux @ F1.2, AGC ON; Color: 0.04 Lux @ F2.2, AGC ON; 0 lux with IR, Angle adjustment- Pan : 0°-355°, Tilt : 0°-67°, Rotation : 0°-355°, Focal Length- 2.8 mm @ F2.0, Defog, Lens Mount- M12, True day/night, 120dB WDR, Image features- 3D DNR, HLC & BLC, Corridor Pattern, IR cut filter with auto switch, Triple streams, Support multi-stream real time transmission, 4 zones video mask, Smart codec by ROI, SNR ≥52 dB, Video Compression H.265, H.264, Video Analytics- Object removal (object left/missing detection), scene change and video blur detection, intrusion and line crossing. Alarm Triggers- Motion detection, Intelligent video analytics, Network disconnect, video tampering, IP address conflict, Max Frame Rate 30fps @ 4MP (2560×1440), Five levels under VBR; Freely adjustable under CBR, time stamp, text overlay, flip & mirror, ROI, Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, white balance, video rotation, Scheduled profile settings, AGC, illegal login, SD Card full, SD Card error, Operating temperature - 30 °C to 60 °C, Relative Humidity 10 % to 90 %, Network-1 RJ45 10M/100M self-adaptive Ethernet port, Network protocol TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP, UPnP, Unicast, Multicast, ICMP, HTTP, HTTPS, DNS, DDNS, RTP, RTCP, IGMP, 802.1X, QoS, Ipv4, Ipv6, Cyber Security -HTTPS / IP Filter / IEEE 802.1X / Blacklist & whitelist / account security / telnet access control / serial password, ONVIF Profile (S & G), HAPI3, FCC Part 15.107 Class A, FCC Part 15.109 Class A , EN 55032, EN 55035 (IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC 61000-4-6, IEC 61000-4-8), EN 55030-4, UL 62368-1, IEC 62368-1 EN 62368-1, RoHS (IEC 62321-3-1, IEC 62321-5, IEC 62321-4, IEC 62321-6, IEC 62321-7, IEC 62321-7-2, IEC 62321-8), WEEE, REACH, CE, NDAA, BIS, Built-in micro SD/SDHC/SDXC slot upto 128GB.

Supply, Installation, Testing and Commissioning of IP based 4 MP resolution (2560 × 1440), Bullet Camera: H.265 4MP IR Vandal Proof Dome N/W Camera, 6mm lens, Fixed Iris, horizontal field of view:110°,Vertical: 77.6°; Fixed Iris, 30M IR, Shutter Speed 1 s to 1/100,000 s, , DC12V/PoE, IP67/IK10, Basic IVA, Image sensor- 1 / 2.7" CMOS, Effective Pixels 2560 × 1440,Min. Illumination Color: 0.01 Lux @ F1.2, AGC ON; Color: 0.04 Lux @ F2.2, AGC ON; 0 lux with IR, Angle adjustment- Pan : 0°-355°, Tilt : 0°-67°, Rotation : 0°-355°, Focal Length- 6mm @ F2.0,Defog, Lens Mount- M12, True day/night, 120dB WDR, Image features- 3D DNR, HLC & BLC, Corridor Pattern, IR cut filter with auto switch, Triple streams, Support multi-stream real time transmission, 4 zones video mask, Smart codec by

ROI, SNR ≥52 dB, Video Compression H.265, H.264, Video Analytics- Object removal (object left/missing detection), scene change and video blur detection, intrusion and line crossing. Alarm Triggers- Motion detection, Intelligent video analytics, Network disconnect, video tampering, IP address conflict, Max Frame Rate 30fps @ 4MP (2560×1440), Triple streams, Five levels under VBR; Freely adjustable under CBR, time stamp, text overlay, flip & mirror, ROI, Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, white balance, video rotation, Scheduled profile settings, AGC, illegal login, SD Card full, SD Card error, Operating temperature - 30 °C to 60 °C, Relative Humidity 10 % to 90 %, Network-1 RJ45 10M/100M self-adaptive Ethernet port, Network protocol TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP, UPnP, Unicast, Multicast, ICMP, HTTP, HTTPS, DNS, DDNS, RTP, RTCP, IGMP, 802.1X, QoS, Ipv4, Ipv6, Cyber Security -HTTPS / IP Filter / IEEE 802.1X / Blacklist & whitelist / account security / telnet access control / serial password, ONVIF Profile (S & G), HAPI3, FCC Part 15.107 Class A, FCC Part 15.109 Class A , EN 55032, EN 55035 (IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC 61000-4-6, IEC 61000-4-8), EN 55030-4, UL 62368-1, IEC 62368-1 EN 62368-1, RoHS (IEC 62321-3-1, IEC 62321-5, IEC 62321-4, IEC 62321-6, IEC 62321-7, IEC 62321-7-2, IEC 62321-8), WEEE, REACH, CE, NDAA, BIS, Built-in micro SD/SDHC/SDXC slot upto 128GB

Supply, Installation, Testing and Commissioning of 28 channel Network Video Recorder, supports up to 12MP recording resolution, Monitor Output Layout (Split Display) : 1x1, 2x2, 3x3, 4x4, 1+5, 1+7, 3+4, 2+8, 1+12, 1+9, 4+9, 2+12, 5x5, 6x6, 8x8 and Sequential, Incoming bandwidth : 512Mbps, Outgoing bandwidth : 512Mbps, Video o/p interfaces : HDMI 2.0 – 1 Port (Main), Audio o/p : 1 Channel, RCA Port, Two Way Audio Input : 1 Channel, RCA Port, Compression technique : H.265/H.264/MJPEG or better, Live View/Playback resolution : Up to 12MP resolution, SATA interfaces : 8 SATA @ 18TB each supported, RAID Arrays : RAID 0 / 1 / 5 / 10 supported, Protocol Support : TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, SMTP, FTP, UPnP, DDNS, RTP, IPV4, DNS, RTCP, ICMP, HTTP, QoS, ARP, NVR Operating System : Linux, Network Interfaces : 2 X RJ-45 10/100/1000 Mbps self-adaptive Ethernet interface, USB interface : Total 3 USB ports: 2x USB 2.0 and 1x USB 3.0, ONVIF : ONVIF Profile S, Alarm I/O : 2IN / 1OUT, Alarm Mode : Manual, Sensor, Motion, Exception, Smart Events, etc., Alarm Action : Record, Snapshot, Call Preset, E-mail, Buzzer, Certification : CE, FCC, BIS, NDAA Compliant.

Supply of CCTV management work station i7-11700 (8 core)/ 2x8GB Memory/1xIntel 512 Gb NVME SSD/1x1TB 7.2 SATA HDD/Win 10 Pro(OEM)/24" Monitor/DVDRW/3 Yrs Wty/460W.

Supply, Installation, Testing and Comissioning of 55" UHD Professional Display, 500 Nits Brightness, contrast ratio 50000:1, Operation: 24x7, Input ports: 1xVGA; 2xUSB 2.0, 4x HDMI 2.0 In, Secure USB 2.0 (Internal), RJ45, RJ12, RS232, Optical SPDIF, 1xHDMI 2.0 out, Supports Daisy Chain, Speaker 2x10 W, 30-degrees Tilting Installation, Open Content Management Support, Scheduler, USB-Autoplay, AutoLaunch, HDMI-CEC, HDMI-Wakeup, Auto-switch on Failover, Panel Lock, OSD Rotation, No Signal Power Off, Screen Saver, Pixel shift, Scheduler, Videowall support, Remote control via LAN, Realtime Clock, Joystick, Rocker Switch, Optional : SDM or OPS compatibility, Embedded IR, IR extender option, Optional: Overlay Touch Kit Compatibility, Certifications: Safety, EMC, CE. including 15 mtr. HDMI cable.

Supply, laying and fixing of 15 Mtr. HDMI Cables

Supply, Installation, Testing and Commissioning of Surveillance Hard Disk 10 TB.

Supply, laying and fixing of UTP 4 pair 23 AWG LSZH CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 305 mtr per Box. Blue in colour conforming to the following standards like ANSI EIA/TIA 568.2-D, IEC 60332-1, IEC 60754-1, ASTM 2843. Frequency tested upto 400Mhz with Third Party Certificate etc. Cable Dia 6.0 ± 0.3, Cross-member (+) fluted Spine/isolator for uniform separation for all pairs.

Supply, Installation, Testing and Commissioning of 24 port Cat 6 19" Modular Toolless Patch Panel (loaded) enable all possible combinations of the various types of cable (UTP, FTP, SFTP) mounted on the same panel by using various toolless connector blocks/modules. Have a metal structure enabling them to be durably fixed to the uprights of the 19” chassis and assuring automatic grounding between toolless RJ-45 connectors, the panel, and the 19” uprights of the enclosure. Include rear cable support with plastic cable guides to hold cable without need for cable ties. Include quick mounting system to mount the panel into the 19” rails without use of cage-nuts. These may be used to secure the c

onnections of wifi access points, IP cameras, servers, or other critical devices. Front Removal IO's option for maintenance and trouble shooting with 6 Different Colours Labels for Labelling & Identification of Individual Ports. Tested and guaranteed under dual circuit IEEE PoE++ more than 90W for up to 2500 on-load connections / disconnections.

Supply, Installation, Testing and Commissioning of RJ45 Connector

Supply, Installation, Testing and Commissioning of 24 x 10/100/1000BASE-T PoE ports, Min 2 x Gigabit SFP ports, Minimum 56Gbps Bandwidth for better Performance, Advanced L2 switching and security features, L2+ Static Routing, Should support Remote and Cloud management, Min 190W PoE budget.

Providing & erecting Optical Fiber cable should be ISO/IEC- 11801 , Outer sheath FRLSZH Shall be 9µ, Single mode OS2 steel armoured cable as per ISO/IEC- 11801 Shall be able to meet Gigabit & 10 Gigabit Ethernet performance requirement specified by IEEE 802.3z (1000 Base-X) & IEEE 802.3ae (10GBase-X) Shall have water blocked construction to prevent water absorption and consequent damages. Water blocking with flooding Gel and water blocking yarn shall comply for IEC 60332-3 for flame retardant, IEC 61034- 2 for low smoke & IEC 60754-2 for toxicity & acidity. Tensile load should be 2700 Newton or higher Optical Parameters – SM, (a) Attenuation @ 1310nm(max) ≤ 0.34 dB/Km, (b) Attenuation @ 1550nm(max) ≤ 0.22 dB/Km with neccessory connections (A) 6 core Single mode

Supply, Installation, testing and commissioning of Wall Moount-15U -600 /600 With Standard Accessories

"Liaison with Local Statutory body for Permanent Electrical Power,DG Set, Transformer,Compact Substation, HT/LT Cable, lift etc. & Getting Approval from Licensee, Electrical Inspector - IM & E Dept. The scope includes to get the required power with providing necessary drg/document/arranging visit etc from requirement of statutory authority. It is lumsum job item and may vary as per requirement. (The payment towards official payment shall be reimbursed against receipt of such payment and it will be in the scope client)"

6 Kg ABC (Powder Type) Fire Extinguisher. In HP Mild Steel Cylinders ISI marked fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged with ABC powder (Mono Ammonium Phosphate) pressured by Nitrogen complete in all respects including wall suspension bracket and conforming to IS:15683 Providing and Fixing of fire extinguishers with necessary accessories, stand, trolley, etc.

Supplying, installation testing and commissioning of CLEAN AGENT FK 5-1-12 Automatic Modular(Self Activated) fire extinguisher Automatic type 15 kg Fire Extinguishers Applicable fire classes A,B & C, UGTS Pressure Gauge, Empty Weight 6.40 kg, Full weight 21.40 kg. Can Height 425mm, Diameter 400 ± 10mm, Made up from 2 mm thick sheet,, Body Construction Deep Drawn with MIG Welding technology, Brass forged sprinkler valves with Nozzle is specially designed to give more than 99% discharge. Together with orifice characteristic to cover adequately fire risks with scattering cone of 40 to 45° Angle. Internal & External Pure polyester (UV Resistant) powder coated, Heat Sensitive Glass bulb of 68 °C. including pressure indicating gauge , celling mounted bracket.

Supplying, installation testing and commissioning of 6 liter K type Fire Extinguisher. In Stainless Steel Cylinders ISI marked fitted with pressure indicating gauge, internal tube, squeeze lever type brass valve fully charged with wet type chemical complete in all respects including wall suspension bracket.

Design, supply and installation of safety signages made of zinc base glow in the dark rigid sheet with high luminous with pasted on 3mm thick on rigid PVC foam sheet. Providing AUTOGLOW Signages in Block / Small Letters of Specified Sizes: "ABC" Extinguisher: 8" X 4"

Design, supply and installation of safety signages made of zinc base glow in the dark rigid sheet with high luminous with pasted on 3mm thick on rigid PVC foam sheet. Providing AUTOGLOW Signages in Block / Small Letters of Specified Sizes: "CO2" Extinguisher: 8" x 4"

Split AC Unit (For Heating & Cooling) Supplying, Fitting & Fixing of A.C. with heating & Cooling facility including supply of all necessary accessories as required for installation of air conditioner (AC). 2 ton Capacity

Providing and Fixing Hard CPVC drain water piping with fittings, support and insulated with 9mm thick closed cell elastomeric nitrile rubber insulation with ASTM E84 25/50 rated - where Flame Spread Index is 25 and Smoke Developed Index is 50, UL94(VO,HB) Passed ,GRIHA(V.3 criterion:14; V.2015 criterion: 8) certified and ASHRAE 90.1, NFPA 90A/NFPA 90B standards compliant Anti Microbial Closed Cell Nitrile Rubber with company bonded GC sheet of 7 mils/200 gsm having K value of 0.036 w/m.k at 24 Deg C with temp range of (-)50 to 105 Deg C. Water Vapor Permeability to be minimum 0.05 Perm-inch without any external barrier with protection against harmful Microbes as per ASTM G-21/UL-181/ASTME-2180-18 with Antimicrobial & Antiviral additive to be EPA approved for use in Drain piping. The material should have JIS Z 2801 Standard for Anti Viral Properties. The insulation material shall and have ozone resistance as per ASTM D 1149 . Adhesives to be GRIHA/IGBC compliant. Installation should be as per manufacturers SOP. 40 mm NB

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

CABINET TYPE FAN FOR EXHAUST AIR Supply, Installation, testing & Commissioning of Cabinet / Inline type Centrifugal Fans for Fresh Air / Exhaust Air System complete with SISW/DIDW blower, fan assembly shall be AMCA certified (AMCA certification requird for Air Performance & Sound) & totally enclosed, fan-cooled, provided with class F insulation, and of approved make., Fan shall be provided with TEFC Sq.cage, direct driven F' Class induction motor. Motor shall be suitable for 220 ± 5% volts, Single phase, 50 cycles OR 415+/-6% V, 50 hz, 3 phase electric supply As per Ventilation Equipment Schedule. The motor (Eff

CIRCULAR INLINE TYPE EXHAUST FANSupply, Installation, testing & Commissioning of Circular Inline type Fans for Exhaust Air System complete with blower, fan assembly shall be AMCA certified (AMCA certification requird for Air Performance & Sound) & totally enclosed, fan-cooled and of approved make., Fan shall be provided with TEFC Sq.cage, direct driven F' Class induction motor. Motor shall be suitable for 220 ± 5% volts, Single phase, 50 cycles OR 415+/-6% V, 50 hz, 3 phase electric supply As per Ventilation Equipment Schedule. The motor (Eff1 Class-Motor must be VFD Compatible ) Max. noise level shall be 56 dBA at 1.5 meter in hemispherical reverberant room condition.Necessary starter shall be in scope of HVAC Contract. Power cable will be available up to starter panel. The controller will be BMS compatible with all required open protocol and requried licence softares. 600 CFM / 15 TSP

Supply Installation , Testing & Commisioning of Propeller type exhuast fan 150 CFM

500 CFM / 30 TSP

Supply Installation , Testing & Commisioning of Cassette Type Exhuast Fan 100 CFM

Sheet Metal WorkSupply installation balancing & Commisioning of Factory Fabricated GSS sheet metal rectangular / round ducts, complete with neoprene rubber gasket, elbows, splitters dampers, vanes, hangers, supports etc as per approved drawings & specifications of following sheet thickness complete as required. Note : Sheet should be 120 GSMThickness 0.63 mm sheet ( up to 750 mm )

Thickness 0.80 mm sheet ( 751 to 1500 mm )

Supply Installation Testing And Commssioning Of Diffusers/ Grilles As Per Following Schedule Supply & Fixing of Powder coated extuded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supply & Fixing of Powder coated extuded aluminium Return Air Grills without volume control dampers completed as required.

Gavity Louvers

Supply, installation, testing and commissioning of decorative facade louver grill suitable for rain protection. Colour & Finish : Approval shall be obtained from Architect Planner / Interior consultant. As per specification/drawings and as directed by Architect & Engineer In Charge

Supply, installation, testing and commissioning of Gl volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Flexible Connections Supply , installation, testing commissioning of Flexible canvass connections to isolate vibrations produced by Air handling units , fans and other air moving equipments when these are to be connected to air ducts where ever specified. Canvass connections shall be of the same cross-sectional area as the mating fan inlet/outlet or duct section. Flexible Duct connector shall be tested and certified in accordance with BS 476 part 7 for class 1 and NFPA -701 from NABL accredited lab

DX ODU Engineered floor support ( 4 to 6 Support for each ODU )

MS Welded Structure (Supply and erection of M.S. angle stand with synthetic epoxy paint )

Minor civil work

Zari Work for drain piping , civil hole making etc

Core Cut up to 150 mm Dia

Soil Mix: Providing and laying of all kind of good soil/ agricultural soil, river sand and organic manure in proportion of 60%, 20%, and 20% respectively. The good soil/ agriculture soil, graded river sand and organic manure shall be provided/ bought by the contractor from approved outside source after testing including transportation, royalties and taxes etc. The engineering garden soil should be fine in texture, free from stones, gravels, plant roots, branches and any other unwanted material, if any. The rate includes supplying, stacking, mixing by mechanical/ manual means, spreading, grading, cleaning and removing stone, gravel, plants, roots, branches, etc. at su

b-base level including spraying anti-termite chemicals according to the manufacturer's specifications. The contractor shall hire a qualified horticulturist with at least 10 years of experience prior to start the landscaping work. The contractor is also responsible for tasks such as uprooting, ploughing, cutting, pruning, weeding, guying, tying, re-planting, spraying organic fertilizer, manuring, pest control etc. for at least (12) twelve months (operation and maintenance) after the final plantation handover including irrigation by mechanical (hydrant pipes, tankers, equipment, tools, tackle etc.) or manual (gardener/ labour) watering as per trees, plants and grass requirement and temperature condition at site.

TREES: Supplying and planting of shade, ornamental, fruit, flowering trees, small, medium and large specimens suitable for Karimnagar region, adaptable to low water, as per under noted varieties, with ht. as specified in drawings including excavation of pit of size 0.75 m x 0.9 m x 0.9 m filling the pit with soil mixture etc. as per specifications and as directed complete in all respect including watering and nurturing the trees. The trees may be planted individually in rows or in cluster as per direction in drg. and all plant material and its sizes and height/girth and crown should be shown to the landscape architect/ Project Manager & written approval to be sought before planting. (Cost excluding soil mix). Trunk Diameter to be measured 300 mm above Polybag. T-1, Grevillea robusta; Height min 3000 mm, Trunk Dimater min. 75 mm

T-2, Bauhinia Blakeana; Height min 3000 mm, Trunk Dimater min. 75 mm

T-3,Prunus serrulata; Height min 3000 mm, Trunk Dimater min. 75 mm

T-4,Magnolia grandiflora; Height min 1500 mm

T-5,Pinus kesiya; Height min 3000 mm, Trunk Dimater min. 75 mm

T-6,Mimusops elengi, Height min 3000 mm, Trunk Dimater min. 75 mm

T-7,Plumeria alba; Height min 3000 mm, Trunk Dimater min. 75 mm

T-8,Swietenia macrophylla; Height min 3000 mm, Trunk Dimater min. 75 mm

T-9,Lagerstroemia indica; Height min 3000 mm, Trunk Dimater min. 75 mm

T-10,Rhododendron arboretum; Height min 1000 mm, spread min 1000mm

PALMS: Supplying and planting of palms as per under noted varieties, with ht. as specified in drg., including excavation of pit of size 0.9 m x 0.9 m x 0.9 m, removal of excavated earth to desired location filling the pit with soil mixture etc. as per specifications and as directed complete in all respect including watering and nurturing the trees. The trees may be planted individually in rows or in cluster as per direction in drg. and all plant material and its sizes and height/girth and crown should be shown to the landscape architect/ Project Manager & written approval to be sought before planting. Trunk Diameter to be measured 300 mm above Polybag. PL-1, Wallichia oblongifolia; Height min 3000 mm, Trunk Dimater min. 75 mm

PL-2, Cycas sp; Height min 1000mm, spread min 1000mm

PL-3 Dypsis lutescens, Height min 300mm, spread min 600mm

SHRUBS: Providing, planting and developing plants/ flower bed with under noted varieties of plants (both shade & sun loving), including excavating the soil to a depth of 450mm - 600mm of required area as per plant species, removal of excavated earth to directed location, filling the excavated bed with approved soil mixture, planting the approved variety plants, providing strong stack etc. as per specification and as directed complete in all respect, including watering and nurturing the plants. Height & spread to be measured above polybag top. S-1, Camellia caduca; Height min 600mm, full of branches and foliage spread min 450mm

S-2,Herbaceous perennial; Height min 450mm, spread min 150mm

S-3,Strelitzia reginae; Height min 450mm, spread min 1000mm

S-4,Nephrolepis Exaltata; Height min 300mm, spread min 300mm

S-5,Hibiscus rosa-sinensis; Height min 1000mm, spread min 500mm

S-6, Gardenia jasminoides; Height min 600mm,spread min 1000mm

S-7,Ixora coccinea red and pink, Height min 600mm, spread min 450mm

S-8,Homalomena aromatica; Height min 600mm, spread min 450mm