REPAIR/MAINT OF VARIOUS TYPES OF LIGHTS INCLUDING OTHER WORKS OF DG SETS AT PUMP HOUSES IN THE AREA OF AGE E/M EXT (WS) UNDER GE E/M LUCKNOW

Amount

Repair/maint of LT Panel 3 phase AC 415V, 50 Hz A of any make including Taking out old /UNSV MCCBs & MCBs /incoming and outgoing laminated copper busbar , DMC/epoxy insulators of any size ,Volt meter, Amp. meter,phase indicator LED lamp,Change over switch of any capacity ,burnt out copper winding ,current coil ,potential coil and keeping aside for safe custody for re-use, opening the LT Panel, removing gasket, dismantling and taking out old parts carefully, disconnecting all conections, & re-assembling all serviceable parts to original position including cleaning , removing sludge, dirt, dust, cleaning of parts including removal of old paint with 02 coat synthetic enamel paint after 01 coat iron red oxide paint along with replacement of nuts, bolts, thimbles, gasket etc as per site requirement including complete testing as per site requirement , complete all as specified and directed by Engineer-in- Charge. Note : All spare parts and rewiring work will be measured and paid seperately under respective item of Sch 'A'.

Supply only MCCB 160 Amps, 415 volts AC 50Hz, 3 pole, bracking capacity 36 kA ajustable thermal setting, Ics=100%Icu@ with suitable size of sheet metal enclosure complete all as specified and directed by Engineer-in- Charge.

Supply only MCCB 200 Amps, 415 volts AC 50Hz, 4 pole, bracking capacity 36 kA ajustable thermal setting, Ics=100%Icu@ with suitable size of sheet metal enclosure complete all as specified and directed by Engineer-in- Charge.

Supply only MCCB 250 Amps, 415 volts AC 50Hz, 4 pole, bracking capacity 36 kA ajustable thermal setting, Ics=100%Icu@ with suitable size of sheet metal enclosure complete all as specified and directed by Engineer-in- Charge.

S & F in repairs MCCB 100 Amps, 415 volts AC 50Hz, 3 pole, bracking capacity 16 kA ajustable thermal setting, Ics=100%Icu@ with suitable size of sheet metal enclosure complete all as specified and directed by Engineer-in- Charge.

Supply only Changeover switch on load in open execution 4 pole 415 V, 50 cycles-100 Amp -02 Nos, complete all as specified and directed by Engineer-in- Charge.

Supply & fix in repair MCB TPN capacity 32 Amps, 415V, 50 c/s 16 KA, complete all as specified and directed by Engineer-in- Charge.

Supply & fix in repair MCB SPN capacity 32 amp, 'C' series , complete all as specified and directed by Engineer-in- Charge.

Supply only Set of indicating lamp LED type, complete all as specified and directed by Engineer-in- Charge.

Gate light LED-40 WATT 215 V, 50 HZ, post top made in cast aluminium spigot housing with decorative clear acrylic diffuser and IP65 protection fix with GI Pipe 40 mm dia 30 cm long (15 cm under the pillar & 15 cm above the pillar ) with proper connecting with existing electric cable in and ilcuding taking out old unservicable light , complete all as specified and directed by Engineer-in- Charge.

Point wiring for one light/fan point controlled by one, one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly and make wall surface as existing same colour including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately)and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing, complete all as specified and directed by Engineer-in- Charge.

All as per item No 14 above but for one socket outlet point 5 amps on independent board controlled by one, one way switch.

All as per item No 14 above but for one socket outlet point on the same baord with other switches.

Point wiring for 15 amps socket point controlled by one, one way switch using 2.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated FRLS unsheathed cables in and including PVC concealed conduit and conduit fittings including pressed steel terminal switch boxes and 3 mm thick plate for fixing of switches/sockets and fitted with Chromium plated brass screws & washers and1.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated unsheathed earth wire and connected to earth dolly including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately)and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing, complete all as specified and as directed by Engineer-in- Charge.

Switch piano flush type of of polycarbonate, SP,5/6 Amps, one way ,complete all as specified and as directed by Engineer-in- Charge.

Switch piano flush type of single pole, 15 Amps, one way ,complete all as specified and as directed by Engineer-in- Charge.

Socket out let 2 in 1 socket 3 pin 5 Amps, flush type controlled by one switch , complete all as specified and directed by Engineer-in- Charge..

Socket out let 2 in 1, 3 pin, 5 and 15 Amps flush type , complete all as specified and as directed by Engineer-in- Charge.

Ceiling rose, Pilot 3 Plate ceiling rose 6A ,complete all as specified and as directed by Engineer-in- Charge.

MCB SP 6 to 32 Amps, 240 Volts of 'B' series to be housed in DBs and suitable size cable lugs to be fixed with MCBs as in replacment, complete all as specified and directed by Engineer-in- Charge.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 32 amps , complete all as specified and directed by Engineer-in- Charge.

Flourescent LED tube light fitting Surface mounting , 1X36 Watt ,energy efficient,ceiling /wall mounting box type fitting complete , with decorative serrated acrylic cover diffused illumination elegantly designed , spring loaded, rotary type lamp holder, connector block etc. and all accessories with 1 No 40/36 watt tube rod including provn of two core flexible copper cable of size 1.5 Sqmm from ceiling rose/connector in and ilcuding taking out old unservicable light , complete all as specified and directed by Engineer-in- Charge.

LT under ground electric power cable crossed linked polyethylene ( XLPE) insulated, galvanised steel strip or wire armoured, ISI-7098 Marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of size 10 sqmm cross sectional area, 2 core ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc. with and including MS Clamps, nuts , bolts, washers including jointing and testing complete and taking out unserviceable cable , complete all as specified and directed by Engineer-in- Charge. Note : Excavation, earth work, sand cushioning, protection bricks/ tiles/ block and pipe shall be measured and paid separately under appropriate items.

All as per item No 26 above but 25 Sqmm 3.5 core.

All as per item No 26 above but 50 Sqmm 3.5 core.

All as per item No 26 above but 70 Sqmm 3.5 core.

Excavation in trenches not exc 1.5m wide and and not exc. 1.5m depth wide in soft/loose soil for laying electric cables/pipes etc including getting out excavated earth and trimming the sides and bottoms of trenches , complete all as specificed and directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each, excavated soil in trenches after the cables have been laid and tested, complete all as specified and directed by Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.50 meter above the starting point , complete all as specified and directed by Engineer-in-Charge.

Supply and spread fine dry sand locally available for cable cushioning complete all as specified and directed by Engineer-in- Charge.

M&L for laying sub class 'B' brick in trenches as cable protection covers across the length of the cable complete all as specified and directed by Engineer-in- Charge.

Aviation Light fitting LED 50 Watt 230 Volts 50 Hz yellow painted die-cast aluminium alloy housing, red coloured polycarbonate dome and accessories. in and ilcuding taking out old unservicable light , complete for O/H Tank of hieght 20-30 Mtrs complete all as specified and directed by Engineer-in- Charge.

Daily Maintenance of AMF Panels of any make and model of 18 D.G.Sets at various locations of in Lucknow Cantt area including cleaning overhauling and repairs to defective AMF Panels after renewal of defective spares / components of any approved Make as per existing or its equivalent complete all as specified and directed by Engineer-in- Charge. [Note :(i) Each AMF Panel shall be cleaned /maintained daily under supervision of EIC (ii) Fixing of defective spares / Components are deemed to be included in the unit rate but cost of spares / components will be paid under respective items here-in-after (iii) Daily maintenance register shall be maintained for each pump house and shall be signed by representative of contractor and the Engineer in-Charge after doing necessary maintenance)

Labour only for repair and maintenance and cleaning of DG set of any make. Capacity-30 to 82.50 KVA including replacement of diesel filter lubricating oil filter, rubber hose pipe, V-belt, Oil pipe, diesel pipe and worn out parts including cleaning of Diesel Tank. (Spare shall be measured and paid separately in relevant item of schedule complete all as specified and directed by Engineer-in- Charge.)

Fuel filter ( Primary & Secondary)

Oil Filter

Air Cleaner

By pass filter

Super bypass filter

Hose pipe set for Kirloskar 32 KVA to 82.5 KVA

Fan belt suitable for 32 KVA To 82.5KVA Kirloskar/Cummins

Banjo bolt off sizes

Screen filter

Fuel Injector pipe for 32 KVA To 82.5KVA

Injector nozzles for 32 KVA To 82.5KVA

Injector plunger and plunger spring for 32 KVA To 82.5KVA

Cylinder liner for 32 KVA To 82.5KVA

Piston with gugen pin & bush for 32 KVA To 82.5KVA

Inlet and Exhaust valve, 32 KVA To 82.5KVA

Tappet bush with packing 32 KVA To 82.5KVA

Valve guide and spring, 32 KVA To 82.5KVA

Piston rings

Alternator booster panel with AVR system and control unit with all asseceries for 32 KVA To 82.5KVA alternator

M&L for dismantling of existing unserviceable asbestos rope and S&F new asbestos rope to DG Set of size 20 mm dia wrapped over the exhaust pipe including fixing complete all as specified and directed by Engineer-in- Charge.

M&L for Taking out FIP from DG set 32 KVA TO 62.5 KVA transporting to service center/contractor workshop for over hauling/calibration and refixing on DG Set after replacement of worn out parts such as screen filter, delivery valves, plunger, O-ring spring rotor assembly injector element etc complete all as specified and directed by Engineer-in- Charge.

All as per item No 58 above but 62.5 KVA upto 82.5 KVA

Taking out of turbo charger from DG Set for 32 KVA to 62.5 KVA capacity transportation to work shop for repairing and replacement of turbo charger kit & refixing to DG Set and testing complete all as specified and directed by Engineer-in- Charge.

All as per item No 60 above but 62.5 KVA upto 82.5 KVA

S&F in replacement alternator (Dynamo) charger suitable for 12 Volt Battery with all accessories i.e. fabrication of mounting brackets nut bolt etc suitable for DG set of capacity 32 KVA TO 82.5 KVA including testing complete all as specified and directed by Engineer-in- Charge. Make : TVS / LUCAS or equivalent Make for Kirloskar/Cummins Engines.

M&L for supply & replacement lead acid battery 12 volt 180 AH 25 plate including initial charging at various DG sets complete all as specified and directed by Engineer-in- Charge. Make : Exide / Amron

M&L for supply & replacement lead acid battery 12 volt 100 AH 25 plate including initial charging at various DG sets complete all as specified and directed by Engineer-in- Charge. Make : Exide / Amron

M&L for draining out old used lube oil from engine sump, cleaning of sump and supply & filling new lubricating oil SAE grade (15 w 30) multiviscoscity complete all as specified and directed by Engineer-in- Charge. Make : Castrol / CRB / Servo / BP

M&L for draining out old used lub oil from engine sump, cleaning of sump and supply & filling new lubricating oil SAE grade (20 w 40) multiviscoscity complete all as specified and directed by Engineer-in- Charge. Make : Castrol / CRB / Servo / BP

Supply and top up coolant/replacement of coolant by new coolant suitable for ambient temp from 15 to 40 degree centigrade complete all as specified and directed by Engineer-in- Charge. Make : TVS

Supply & pouring distilled water superior grade all as approved complete all as specified and directed by Engineer-in- Charge.

S&F turbo charger with all accessories suitable for DG set suitable for 32 KVA TO 82.5KVA Make-kirloskar/ cummins or others complete all as specified and directed by Engineer-in- Charge. Make - Auto lac

M&L for dismantling and transporting to contractor's work shop of alternator by opening of nut bolts of base plate and coupling opening of front and rear cover removing of fan and removing of armature, rewinding of alternator by super enameled insulated copper wire as per existing gauge, insulating materials, varnishing, drying in hot oven up to desired temperature assembling and testing on connected load complete all as specified and directed by Engineer-in- Charge of Cap 32 KVA to 82.5 KVA. Note : (Cost of transportation is deemed to be included in quoted rates)

Material & labour for preparation of old painted surfaces by removing of dust and dirt by caustic soda or any other means, painting of DG set CAP.32 KVA to 82.5KVA of various capacity complete alternator & engine parts as per colour code by spray painting applied two coat of synthetic enamel paint over existing painted surface and marking of SM/MES No on the sets as per approved colour complete all as specified and directed directed by Engineer in Charge.

Supply & replacement of self starter 12 volt suitable for 32 KVA To 82.5KVADG Set complete all as specified and directed by Engineer-in- Charge. Make : Lucas/Autolac

M&L for taking out of burnt out AVR system of DG set cap 32 KVA To 82.5KVA by opening of connection chamber of alternator dismantling all existing electric/electronic connection replacement of AVR set reconnection checking of all circuit, testing the same up to the satisfaction of Engr in Charge

M&L for taking down unserviceable self starter 12 volt from DG Set transporting to contractor workshop dismantling pinion etc , rewinding of armature and field coil by suitable size of insulated copper wire, to achieve its original performance, varnishing, replacement of pinion, pinion spring, carbon brush etc reassembling the same, testing and refitted with DG Set and testing complete all as specified and directed by Engineer-in- Charge.

Supply and fixing in replacement of solenoids switch for auto on off manual mode in the engine operation including wiring complete all as specified and directed by Engineer-in- Charge.

M&L for dismantling of water pump assembly from the the DG sets and supply and fixed new water pump assembly for the DG sets of capacity 50/60/62.5/ 63/82.5 kVA including testing complete all as specified and directed by Engineer-in- Charge.

Dismantling the water body pump assembly complete from the DG set of capacity 82.5 KVA to 250 KVA at site and transporting to work shop & testing and carrying out the following and brought back at site and fixing the same complete all as specified and directed by Engineer-in- Charge. (a) Over hauling of water body pump complete - 01 Job, (b) Supply and fix water body kit complete- 01 Set, (c) water body bearing - 02 Nos, (d) water body Hose- 01 Set,

Supply only battery terminal heavy duty made out of brass suitable for 12 volts lead acid battery complete all as specified and directed by Engineer-in- Charge.

M&L for replecement of horness cable control wiring and testing complete all as specified and directed by Engineer-in- Charge.

S&F off load change over switch cap 100 Amps 4 pole 415 Volts by addition/alteration in existing wall complete all as specified and directed by Engineer-in- Charge.

S&F off load change over switch cap 200 Amps 4 pole 415 Volts by addition/alteration in existing wall complete all as specified and directed by Engineer-in-Charge.

HRC fuse 4-10 amps etc complete for DG sets installed at various pokets under AGE E/M EXT(ELECT) complete all as specified and directed by Engineer-in- Charge. Note:- Spare required for repairs shall be measured & paid separately as supply only.

Supply & fix in repairs electronic control timer type ET-100 of suitable capacity as required at site complete all as specified and directed by Engineer-in- Charge. Make:- L&T/ABB/ Legrand/ AE/Secure.

Supply & fix in reapirs engine starter relay of suitable capacity as required at site complete all as specified and directed by Engineer-in- Charge. Make:- L&T/ABB/ Legrand/ AE/Secure.

Supply & fix in repairs under voltage relay complete all as specified and directed by Engineer-in- Charge. (Make:- PIC / EC / Wader.)

Supply & fix in reapirs 8 / 11 pin relay complete all as specified and directed by Engineer-in- Charge. (Make:- PLA.)

Supply and fixing in repairs crocodile clip for battery chargers of required size complete all as specified and directed by Engineer-in- Charge.

Three Pole Power Contractor -Type MNX-185 complete all as specified and directed by Engineer-in- Charge. Make-L&T

Four Pole Power Contractor -Type ML-06 complete all as specified and directed by Engineer-in- Charge. Make-L&T

Single Phase Preventor Relay + Timer 415 Volt complete all as specified and directed by Engineer-in- Charge. Make L& T

DIN Type Fuse Link Type HN Suitable for up to 200Amps complete all as specified and directed by Engineer-in- Charge. Make-L&T

Push Button Pendants 06 Amp, 415 V,50Hz with 02 push buttons complete all as specified and directed by Engineer-in- Charge. Make-L&T

M/S Nav Jyoti Enterprises

Magneoflux

Shree Tirupati Associates

Ajanta Associates

M/S AMARJIT SINGH