REPAIRS TO FENCING, DRAINS, HARDSTANDING, PATH, RETAINING WALL, SECURITY WALL AND GATE AT ZONE A AND ZONE B AREA AT SHILLONG CANTT UNDER GE SHILLONG

Amount

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground in natural ground etc complete all as specified and directed by Engineer-in-Charge.

Demolition of Precast cement concrete block walling built in cement mortar ,in any position, complete all as specified and directed by Engineer-in-Charge.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of Cement Concrete of any description ( reinforced) and in any position not otherwise specifically provided for etc complete all as specified and directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, and removing surplus soil to a distance n.exc. 50 m from the starting point etc complete all as specified and directed by Engineer-in-Charge.

M&L PCC type C2 ( 1:3:6, using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

S&F mild steel flat iron / angle iron fixed to posts to hold chain link fencing and similar small articles conforming to Fe-290 Gde-E-165 etc complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel 11 to 15 mm dia screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm long but n.exc. 10 cm long etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC Block masonry with solid precast cement concrete blocks made out of cement concrete 1:3:6 type C1, (using 20 mm graded stone aggregate), exc 10 Cm width and setting in cement sand mortar 1:6 including demolition of old unserviceable one and removing the debris completely from site and throwing in low lying area outside MoD land etc complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick or concrete surfaces in anyposition including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MD land all specified and directed by Engineer-in-Charge.

M&L for Rendering 10 mm thick plaster on fair faces of brick work or concrete surfaces in cement sand mortar (1:4) finished even and smooth without using extra cement complete all asspecified and directed by Engineer-in-Charge.

M&L for Rendering 15 mm thick plaster other than fair faces of brick work or concrete surfaces in cement sand mortar (1:6) finished even and smooth without using extra cement complete all asspecified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of wall and applying two coats of white or tinned cement base paint over a coat of exterior grade wall primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated surfaces of steel of any description and girth, not otherwise described and treated with two coats synthetic enamel paints over a coat of red oxide primer complete all as specified and directed.

Dismantling of barbed wire fencing of any description, size, spacing etc all as specified and directed by Engineer-in-Charge.

Dismantling fencing wire mesh including fixing arrangement like flat iron, angles of any type etc complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed by Engineer-in-Charge.

Restraing and resecuring incl making good staples etc. of barbed wire complete all as specified and directed by Engineer-in-Charge.

Supply only Chain link MS galvanised fencing, any size or type etc complete all asspecified and directed by Engineer-in-Charge. .Note:- The unit weight of chain link shall not be less than 4 kg per sqm.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of new GI binding wire etc complete all as specified and directed by Engineer-in-Charge.

S&F mild steel works such as Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge.

M&L for Mild steel TMT bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete specified and directed by Engineer-in-Charge.

S&F in repair 1.00 mm thick Mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bendingmor turning up, mitred angles, etc.complete all as specified and directed by Engineer-in-Charge.

M&L PCC type C2 ( 1:3:6, using 40mm graded crushed stone aggregates) as in surface channel and drain including necessary formwork etc complete all as specified and as directed.

M&L for Machine pressed pre-cast concrete rubber moulded coloured interlocking paver block of any shape and size conforming to IS : 15658-2006 , 60mm thickness, M-35 grade of approved design jointed with grey cement and pigment etc complete all as specified and as directed.

M&L for Sand filling under floor including watering and well ramming for laying of interlocking paver blocks complete all as specified and directed by Engineer-in-Charge.

M&L for RCC type A-1, 1:11/2:3 as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, Canopies, deck slabs and in shelves etc complete all as specified and directed by Engineer-in-Charge.

M &L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc complete all asspecified and directed by Engineer-in-Charge.

M&L for machine pressed pre polished factory made pavement chequered cement concrete tiles of size 300 X 300 X 25 mm thick of approved design and colour , set jointed and pointed in neat cement slurry with grey cement and pigment over and including 15 mm thick screed bed in cement sand mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

M&L for dark shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement sand mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M/S INSHA ELECTRICALS