Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹23.8 CrAccepted-AOC | ₹23.8 Cr Quoted ₹24.6 Cr | L1 | Accepted-AOC ACCEPTED |
| 2 | L2₹24.9 CrRejected-AOC | ₹24.9 Cr | L2 | Rejected-AOC REJECTED |
| 3 | Rejected-Technical NAMAKKAL | - | - | Rejected-Technical Finanical Turn over not satisfied |
Tender Value
₹23.8 Cr
EMD Value
₹12.0 L
Closing Date
24 Nov 2023, 3:00 pmClosed
JOINT COMMISSIONER ARULMIGU KAPALEESWARAR TEMPLE
ARULMIGU KAPALEESWARAR TEMPLE MYLAPORE CHENNAI
CONSTRUCTION OF CULTURAL CENTER BUILDING IN ARULMIGU KAPALEESWARAR TEMPLE LAND AT GREENWAYS ROAD RA PURAM CHENNAI 600028
2023_HRCE_382709_1
2/2023-24
Open Tender
Civil Works - Buildings
510 days
GREENWAYS ROAD
Please refer Tender documents.
20 documents required · 20 mandatory
₹0
₹12.0 L
Yes
ARULMIGU KAPALEESWARAR TEMPLE MYLAPORE CHENNAI
20 Feb 2024
27 Oct 2023
24 Nov 2023
27 Oct 2023
24 Nov 2023
27 Oct 2023
27 Oct 2023 - 23 Nov 2023
20 Nov 2023
Amount
Dismantling, clearing away and carefully stacking materials useful for re-use Brick / Stone Masonry in cement mortar walls under 3m high
Dismantling RCC by manual / by using deploying machineries
Dismantling Doors and Windows including removal of frames, hinges and fastenings
Dismantling Corrugated Iron Sheet Roofing over Pan Tiles without roof timbers
Installation of Vertical Bored cast in situ RCC piles in all types of soils, using Ready Mix Concrete of M 30 grade, with sulphate resistant Cement, fine aggregate, 20mm and down graded HBGS jelly coarse aggregate. The rate excludes cost of reinforcing steel, binding wire, fabrication, welding charges, placing of reinforcement cage in bore hole in correct position and including cost of boring to the required depth with Bentonite solution with temerory casing of required length, conveyance of RMC to site and pouring concrete using Tremine pipes, conveyance of all materials to the site including all tools and plants, shifting the plants and equipments from one point to another, excavation of mud pits for circulation of Bentonite solution, closing the mud pits to original level and mud removal with initial lead and lift but including dismanting the concrete above the cut off level etc complete as directed by the departmental officers including socketing. The reinforcement cage should be welded properly for lifting. The concrete cubes to be tested as per IS 456-2000. Acceptance criteria by clause 16.1. Frequency of testing should be as per clause 15.2.2. The length of pile for payment shall be measured up to natural ground level. The work should be carried out as per IS 2911. Pile depth should be decided by the departmental office at site.
450 mm dia pile
600 mm dia pile
Providing pile foundation 12" dia augur pile for a depth upto 3.50 m including M 30 Design Mix, using 20mm Hard Broken Stone jelly etc. all complete, excluding reinforcement. (For Compound wall)
Initial Load Test as per IS 2911 Part IV 1985 including cost of single pile (250% of pile capacity), labour, reinforcement charges and all other incidential charges including excavation, shoring, strutting, dewatering, mobilization of equipments, etc. and also necessary hire charges for jacks, measuring devices, Structural Frame work for platform, Kent ledges etc, as required and providing pilecap.
For 600 mm dia piles
For 450mm dia piles
Routine load test as per IS 2911 part IV 1995 (150% of pile capacity) including mobilization charges, labour charges for jack, measuring devices, structural frame work plot form, kent ledges etc., as required and as directed by the departmental officers etc. complete.
For 600 mm dia piles
For 450mm dia piles
Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.
Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification
Supplying and filling in foundation and basement with STONE DUST in layers of 150 mm thickness well watered rammed and consolidated complying with watered rammed and consolidated complying with relevant standard specifications including cost of filling sand as directed by the Departmental officers.
Supplying and filling in foundation, basement, etc with filling M sand sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.
Supplying and filling in foundation and basement with Gravel in layers of 150 mm thickness well watered rammed and consolidated complying with watered rammed and consolidated complying with relevant standard specifications including cost of filling sand
Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000,using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kglms and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).
For Basement & Foundation
For Ground Floor
For First Floor
For Second Floor
For Third floor
For Terrace floor
Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)
Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)
Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)
For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.
For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.
Brick work in 1:5 Cement Mortar using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.
Brick work in 1:6 Cement Mortar using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.
In Ground floor
In First floor
In Second floor
In Third floor
In Terrace floor
Brick partition walls of 11.50cm thickness using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)
In Ground floor
In First floor
In Second floor
In Third floor
Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers
Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.
Providing two coats putty for the walls including cost of putty, labour charges , scaffolding etc., complete complying with relevant standard specification and as directed by the departmental officer.
Painting the New Walls with two coats of approved Plastic Emulsion paint over one coat of primer over Cement Plastered wall surface including cost of brushes, emulsion paints curing etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality and shade of paint should be got approved by the Executive Engineer before use).
Painting the wall with Texture Finish Paint including labour charges complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality and shade of paint should be got approved by the Executive Engineer before use).
Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete
Supplying and fixing ornemental Double leaf Teak Wood Door of size 3m x 2.40m including teak wood frame of size 0.15m x 0.15m with panel of 45mm thick as per design including cost and labour for fixing the Brass furniture fittings viz. 2 no. of Door Handle 3 nos. of 5" Brass Butt hinges, 2 nos. of 6"x1/2" Tower bolt,1no. of 10"x5/8" Aldrop, 1no. of Rubber bush with required polishing,screws etc. all complete complying with relevant standard specifications and as directed by the departmental officers.
Supplying and fixing of soild core Flush shutters with Teak ply on both sides with teak wood lipping all-round 35 mm thick including cost and labour for fixing the Aluminium furniture fittings viz. 2 no. of Door Handle 3 nos. of 5" Aluminium Butt hinges, 2 nos. of 6"x1/2" Tower bolt,1no. of 10"x5/8" Aldrop, 1no. of Rubber bush,1no. of door stopper with rubber bush, with required screws etc. and Polishing the teak wood door with two coats of best French (Lac) polish with approved quality and brand over a coat of bee's waxing including preparing the wooden surface to receive polishing, etc., c (The make, quality and colour of french polish, bees vax should be got approved by the Executive Engineer before use on works.) all complete complying with relevant standard specifications and as directed by the departmental officers.
Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 1800mm x 700mm with following specifications. A.Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b.Door leaf 1mm: Galvanized 120 GSM branded make JSW c.Shutter Thickness: 46mm d.Honeycomb: In-fill e.Glue Macroplast UR-7221 f.Door Hinges: 4" x 3" x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS304 - Finish SS g.Door Closer with Standard Arm Finish:Silver h.Lock Set: Dead Lock with both side key i.Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating : Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns l.Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent n.Vision Panel 200 x 300mm 2 Hrs. Fire Glass Schott Pyran with Frame 0.Rated Glass Schott Pyran with Frame p.Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, plastering, scaffolding all other conveyance as per standard methods and as directed by the Departmental Officers.
Supplying and fixing wood polymer composite board solid door frame and 25mm thick shutter frame corners of extruded outer size 75mm X 50mm the inner core more rigid WPC composite with minimum shore hardness of 55 and bulk density 0.8 Grams per cubic centimeters. The frame shall be fixed to the wall using 10 X 100 mm long MS screw through the frame through the pvc fastener. Minimum three numbers of screw to be provided for each vertical member. The overall size of frame shall be with suitable rebate for housing shutter and shutter consist of 25mm polymer composite board single core exhaust with one side embo printing design. To avoid duplicate from the printing design shall have logo of the WPC board shall be bount aid proved by kept official. The shutter shall be provided with 3 Nos of 4” SS butt hinges, 2 Nos of 4” Stainless Steel handles, 3 Nos of 6” Stainless Steel tower bolts with required Stainless Steel screws including labour charges for fixing the shutter frame, shutter and furniture fittings in position and finished smooth with template etc., all complete in all respects complying with relevant standard specification and as directed by the departmental officers
Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.
Supply and fixing of UPVC glazed window made out of hollow multi-chambered UPVC sections having isolated drainage and reinforced with galvanized steel. The corners and joints shall be mitre cut and fusion welded. The outer frame of the window shall be made out of UPVC sections having an overall size of 60mmx60mmx40mm having wall thickness of 2.3mm, + or - 0.3mm and provided with steel reinforcement at a hardware location and size of 27mmx21.5mm. The fixed mullion shall be made out of UPVC sections having an overall size of 76mmx60mmx36mm having wall thickness of 2.3mm, + or - 0.3mm.
Supply and fixing of UPVC ventilator made out of hollow multi-chambered UPVC sections having isolated drainage and reinforced with galvanized steel. The corners and joints shall be mitre cut and fusion welded. The outer frame of the window shall be made out of UPVC sections having an overall size of 60mmx60mmx40mm having wall thickness of 2.3mm, + or - 0.3mm and provided with steel reinforcement at a hardware location and size of 27mmx21.5mm. The fixed mullion shall be made out of UPVC sections having an overall size of 76mmx60mmx36mm having wall thickness of 2.3mm, + or - 0.3mm.
Supplying and fixing of mild steel grills to windows and ventilators including cost of necessary screws and cost of applying priming coat of paint etc.,
Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive ofhood covers, transportation charges etc
Providing band with cement mortar 1:5 (One of Cement and Five of Sand) 12mm thick finished with neat cement including,scaffolding curing, etc.,complete complying with relevant standard specification and as directed by the departmental officers (7.5 cm width).
Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
Supplying and fixing in position of colour Double Charged Vitrified Floor tiles (600x600mm) of any size of approved special quality of 10 mm thickness laid in cement mortar 1:3( One of cement and three of sand) 20mm thick for flooring including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers. Note:( The colour and quality shall be approved from the E.E before use only one particular size of ceramic wall tiles to be used for one building)
Supplying and laying of Joint free Rectified Glazed Ceramic Flooring Tiles 305 x 305 x 8mm thickness laid in cement mortar 1:3( One of cement and three of sand) 20mm thick for flooring including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers. Note:( The colour and quality shall be approved from the E.E before use only one particular size of ceramic wall tiles to be used for one building)
Dadooing walls with following best approved quality, white / colour glazed tiles of following 300 x 450 x 8mm set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.
Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification. (For steps)
Supply and fixing of polished jet Black granite wall cladding slab of 10mm to 12 mm thick of best approved quality laid in C.M. 1:2(one of cement and two of sand) 12mm thick over the wall in all the floors including cutting the granite slab to the required size wherever necessary fixing in position finishing edges neatly including the cost of granite slab nosing , polishing laying etc., complete in all respect as directed by the departmental officer.(For Lift faica)
Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.
Ground floor
Third floor
Fourth Floor
Paving the Top of roof with Solar reflective ceramic tiles of size 305 x 305x 7mm thick of approved quality and colour laid in Cement Mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officer. (The make and brand of the tiles should be got approved by Executive Engineer before use of work).
Providing expansion joint of 12.5 mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed.
Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete complying with relevant standard specification and as directed by the departmental officers.
Supply of laying of Anutone (or) Equivalent Brand of Acoustical Insulation of Sound Synth Polywool, 50mm thick made from recycled poly fibre and fully recyclable, surface density 1000 g / m2, weight 1.0 kg / m2 in form of rolls of 600mm wide and 15m in length, adhered to surface with stick S7 adhesive or held in position with chicken wire mesh etc., complying to standard specication.
Supply and installation of Anutone (or) Euivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc. complying to standard specification.
Providing and fixing Acoustic Wall Panelling (equivalent to Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a "Helmholtz" fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be "tongue-and-grooved" to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by Armstrong and approved by the Engineer-in-Charge.
Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875. Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm.
Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer
Ornamental Brick work in COMBINATION MORTAR 1:1:4 mix using country bricks 83/4"x43/8"x23/4" all vari vargams, moulds, sthambas, mukapatram, koodu, nasi, and all ornamental brick work complete panchavarnam agaraies, karnakoodus etc forming core walls rajagopuram/vimanams complete in cluding cement al labour chage (Sthapathi work for elevation)
Providing vargapoochu over the corewalls of Vimanams/Gopurams, with Cement martor1.4 complete including shaping the mukhapathram, mahannasi,koodu all arnamental works to proper shape, by embedding broken bricks or shaped/chiselled bricks, rough - plastering with Cement martor1.4 and finishing with final ornamental plastering and nayam theervai including cost and conveyance of all materials labour therefore, lifting of materials, all woeking in heights curing with water etc, complete - including all extra for folding and including clearing the debris from the vimanams/ Gopurams - Upto 50'0" height (Sthapathi work for elevation)
Painting water based with multicolour (Panchavarnam ) good Emultion paint complete for the Vimanams/Gopurams, including cost and conveyance of all materials, labour charges includingArtist painter, working in heights , lifting of materials, cost of brushes etc., complete - which include all extra for foldings - Upto 50'0" height
Providing and laying Sub Grade with quarry rubbish of good grade of material for 150mm thick to give CBR of 10 on prepared sub grade in accordance with 45% of gravel and quarry dust for filling the voids including cost and conveyance of materials, labour charges for spreading and consolided by power roller to the requirement of departmental officers.
Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc.
Cement Concrete 1:3:6 (One Cement, Three crushed stone sand and six hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification
Supplying and Laying Rubber Moulded hydraulic pressed paverblock of 83mm thick with new one using cement concrete 1:2:4 for manufacturing, finishing, Curing and conveyence to site and laying etc., complete complying with standard specification and as directed by the deparmental officers.
Drilling of 150mm dia Bore well including Transportation from one place to another in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc., by taking pilot bore of 150mm dia and then enlarging to 300 mm dia direct of reverse
Reaming of 150mm dia Pilot Bore to 300mm dia Bore well upto a depth of 65metre ending below Ground level as directed by the departmental officers.
Providing Rainwater Harvesting pit by earth work of 90 cm dia and 60 cm depth and filling with stone jelly 40 mm size including bearth work excavation filling work with the stone jelly and covering with precast well ring RCC 1:2:4 including cost
Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.
160 mm dia
Supplying, laying, fixing and jointing the following UPVC pipes as per ASTM D – 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness excluding the cost of suitable UPVC/GI specials like Elbow, Tee reducers, Plug , union, bend, coupler, nipple etc., wherever required above ground level including the cost of Teflon tape, special clamps, GI Bolts and Nuts, nails, etc., fixing on wall to the proper gradient and alignment and redoing the chipped masonry after the pipes are laid, fixing charges etc., complying with relevant standard specifications & as directed by the departmental officers.
50mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials
40mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials
32mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials
25mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials
20mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials
Supplying and fixing of GM Gate valve 50mm Dia heavy duty labour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from Executive Engineer before use).
50mm dia
32mm dia
Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements
UPVC Elbow
50 mm dia
40 mm dia
32mm dia
25 mm dia
20 mm dia
UPVC Tee
50 mm dia
40 mm dia
32mm dia
25 mm dia
20 mm dia
UPVC Reducer
50x40mm dia
40x32mm dia
32x25mm dia
25 x 20 mm dia
UPVC Reducer Elbow
50x40mm dia
40x32mm dia
32x25mm dia
25 x 20 mm dia
UPVC Reducer Tee
50x40mm dia
40x32mm dia
32x25mm dia
25 x 20 mm dia
UPVC Hex Nipple
50 mm dia
40 mm dia
32mm dia
25 mm dia
20 mm dia
UPVC Union
50 mm dia
40 mm dia
32mm dia
25 mm dia
20 mm dia
Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works).
15mm dia CP Screw Down Tap
15mm dia CP Pillar Tap
Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)
Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).
Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).
Supplying and fixing of Health faucet including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use).
Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).
Supplying and fixing in position best quality approved make white glazed earthernwere sink of size of 600 x 450 x 200mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]
Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC soil pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).
Supplying and fixing in position white European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)
Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)
Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)
Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three crushed stone sandand Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.
Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level
75mm dia PVC soil / waste pipe
110mm dia PVC soil / waste pipe
160mm dia PVC soil / waste pipe
Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.
Supplying & fixing PVC mould CI Steps for Sump etc all complete in all respects complying with relevant standard specification and as directed by the departmental officers.
Supply and delivery of following dia P.V.C Casing Pipe and specials as per IS 12818/1992 of approved quality for Bore well
150mm dia Pvc pipe
150mm dia Slotter Pvc pipe
150mm dia Pvc end cap
Labour Charges for inserting 150mm dia P.V.C Pipes assembly ( with or without slots ) in the drilled hole including jointing P.V.C Pipes with couplers with cement paste complete and supplying and packing annular space with pebbles of good quality - to Bore Well - (TWAD SOR 21-22 No.14d)
Charges for developing the bore well with air compressor of 600 CFM Capacity including Transportation ,Labour and fuel charges for compressor as directed by the departmental officers and conducting Yield test by' V ' Notch method all complete as directed
Supply, delivery, erection and commissioning of 2.0 HP with clear water vertical wet type deep well submersible pump set suitable for 150mm dia borewell of best approval quality with ISI Mark, IS 8034/2002 as amended thereafter and BEE 3 Star Rated capabl
Supply and delivery of direct online starter confirming to IS13947, ICE 60947-1 suitable KW rating for operation in AC/ three Phase/50HZ(+/5%) and 415V (+/- 10%) including Ammeter, Overload relay, under Voltage release with no Volt coil, Air Break contact
Supplying and laying of PVC insulated and sheathed 4 Core Flat type 16 Sq.mm Copper Cable Confirming to IS 694 / 1990 with ISI mark for 3 phase submerisible pump set including labour charges for laying cables below ground level including earth work excava
Supplying and laying of L.T. Cables 4 Core 1.1 KV Grade Armoured Aluminium Conductor cable confirming to IS 1554 part I with ISI mark 16 Sqmm cable below ground level including earth work excavation and refilling charges, cost of all material Labour charg
Supply and laying of all materials and termination of 4 core 16 Sq.mm AYWY/A2XY/AYFY aluminium LT UG cables using double compression type cadmium plated brass cable glands suitable crimped type cable lugs(copper), cable identification tags and including
Supplying and laying of 40mmdia HDPE pipe for submercible of 10kg/cm including laying, cutting, jointing etc.,
Nylon rope of good quality tying the motor in proper way and as directed by the departmental officers.
Supply, delivery, erection and commissioning of 5.0 HP submersible pump set best approval quality with ISI Mark, IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging 250LPM against 60m head of water column due to all causes. The
Supply, erection, testing and commissioning of Gun Metal Non-Return Valve of size 50mm dia including necessary MS flange of table „E‟, gaskets, bolts & nuts, etc., installed at pump house delivery line for the purpose of priming to suction line so that to
Supplying and fixing of water level independent high vertical jet of 1.5inches BSP connection high vertical jet at size of 235mm height with 19 mm orifice with ball joint made up of brass with nickel plating, complete
Supplying and fixing of ball joint made up of stainless steel 304 grade etc., complete
Supplying and fixing of 5 H.P open well submersible mono block water - cooled pump. (Three phase -2880 rpm- 440 volts -50Hz suguna or CRI make or Texmo or equivalent make) made up of high grade cast iron materialsetc. Complete
Supplying and fixing of suction strainer made out of ss304 grade materials and covered with ss Meshets. Complete.
Supplying and fixing ofsupreme or equivalent make ASTM D1785 sch 40UPVC pipes ASTM D2467 sch 80 UPVC fifting & control valves for connect pump to 10 feet dia ring ect, complete.
Supplying and fixing of 3' X 2.5' size of wire mesh of size 1cm X 1cm 2mm thick 14 gauge unit made upof stainless steel with ss frame for protect the pump from the dust and garbage articles etc, complete.
Supplying and fixing of multi - colour 27 watts - 12 volta DC RGB under water L. E.D lights made up of die cast stainless steel 304 grade suitable to be fitted with emitter type power LED;s with all in one optical lens of 85% efficiency step tempered galss 8mm with protection class of IP -68 i/C connection & water proof jointing sealed with heat resistan with mounting cradle made upn of stainless steel etc, complete.
Supplying and fixing of necessary electrical items like control panel made up of 16 SWG powder coated mild steel including BCH/ L&T or equivalent make panel board for 5H.P pump consisting of isolated switch , phase light , start and stop push buttons , contactor, relay , volt meter , ammeter in a powder casted mild steel enclosures , 40 Amps 4 pole Legrand / L&T or equivalent make isolator , 20 amps single pole Legard / L&T or equivalent make miniature circuit breaker , necessary 1.0 sq.mm 4 core Havels / polygon / finolex or equivalent make electric cables, automatic color changing on - OFF time control 1no.for lights with powder coated mild steel control panel 1no.etc, complete.
Supplying and fixing of necessary S1BN8- F tupe cable - 7x4 + 5x1.5 size electric cables for pump and 1sq.mm 4 core havels / polygon / finolex or equivalent make electric cables for lights etc. complete.
Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling wht rotating wheel to open and close the valve including MS flange of table 'E' bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.U153
Supply, installation of Fire fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20 mm dia ball valve and open and close spray nozzie, warm clip, etc., as per the standard pattern of nay reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doiing the dismantled portions to its original condition wherever found necessary., etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.
Supply, and fixing in position of Fire fighting Application Hose of 63mm dia of 15 metres length binded by coppper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.
Supply, and fixing in position of Fire fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzie of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.
Supply of Fire fighting Application Application MS Hose Box to keep two number of hoses and 1 no. of branch pipe with nozzie having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.
Supply, erection, testing and commissioning of following MS 'C' Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10kg /sq.cm including necessary fittings like MS flange of table 'E' elbows, reducers, gaskets, bolt, nuts wth washerr & joints as per standard method of arc welding, including one coat of metal primer and two coat of Post Officer Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL/ EQUIVALENT.
200mm dia
150mm dia
100mm dia
Supply erection testing and commissioning of Eletric Motor Driven Fire Pumpset suitable for automatic operation and consisting of following . A. 1 No. horizontal split casing centrifugal type fire pum capable of delivering 4550 LPM against a total head of 110 metres, so as to ensure a miniimum pressure of 3.5kg. per sq.cm at the fartherst top most hydrant / outlet with pum pcasing of cast iron to grad FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring etc., of non corrosive metal either like brone, brass or gun metal and shaftof stanless steel. b. 1 No. suqirrel cage induction motor of 175 HO,, 415 Volt, 3 phase 50 Hz rating, conforming to IS 325-1978 with class "F" insulation, totally enclosed, IP 55 for enclosure fan cooled type conforming to relevant protection clause of IS 4691, synchronous speed of 2900 RPM. c. Common bed plate fabricated with MS channel / Cast iron type for assembling the pump and motro flexible coupling between the pump and the motor wiht coupling guard for protection - 1 No. d. Making cement concrete foundation suitable for the above pumpset including vibration isolation pads as necessary, foundation bolts, brackets, clamp fixtures, grouting etc., In accordance with the manufacture's design and as per standard methods and including conveying, fixing and incidiental charges, etc., complete as per standard specification and as directed by the Departmentaql Officers.
Supply, erection testing and commissioning of following sizes of Heavy Duty Foot Valve including all accessories, such as MS flange of table 'E' gaskets, bolts & nuts etc., installed at end of 150/200mm dia suction pipe line at sump i including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT.
150mm dia
100mm dia
Supply, Installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of followings complete in all respects as required. a.1No. Horizontal split casing centrifugal type fire pump cable of delivering 2850 LPM against a total head of 70 metres, so as to ensure a minimum pressure of 3.5 kg per sq.cm at the farthest top most hydrant /outlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring, etc., of non-corrosive metal either like bronze, brass or gun metal and saft of stainless steel. b.68 BHP, 1500 RPM water cooled with radiator, diesal engine conforming to relevant BS & IS standard complete. c.Auto starting mechanism, 12 volts /24 volts electric starting equipment llike self motor, dynamo, solenoid switches etc., d.110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre filter, after filter etc....... e.Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessary MS support arrangements from wall or ceiling as per site condition. f. Dash board consisting of the instruments like Temperature Gauge, Galvano Type DC Ammeter, Lubricant Oill Pressure Gauge, Ignition Switch, Emergency Stop and all other pretection equipments as per specification, stop soleneid for auto stop in the event of fault with audio indications, painted with Post Office Red Colour etc., as required. g.12V.24V, storage battery, maintenance free tape, 180AH rating, MS fabricated common base plate, coupling guard, foundation bolts, etc., as required. h.Positioning the Diesel Engine Driven Fire Pump over cement concrete foundation using suitable size anti vibration mounting arrangements. The works including conveying, fixing and incidental charges, etc., completed as per standard specification and as directed by the Departmental Officers. (Make: KIRLOSKAR/EQUIVALENT).
Supply, erection, testing and commissioning of Fire fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 metres head with Electrical Motor of 60 HP of 415 volt 3 phase connection complete with base plate and accessories (Make: Kirloskar or Equivalent). The rate inclusive of necessary vibration, bad mounting etc., as per standard method as directed by the Departmental Officers.
Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table 'E' gaskets, bolts & nuts including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT. a) 150mm dia
Supply, erection, testing and commissioning of Cast iron and Gun metal or stainless steel internal Non return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table 'E' gaskets, bolts & nuts etc., as per IS 5312 including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. a) 150 mm dia
Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14kg. Range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe ling in pump house to read the developing pressure including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.
Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motro including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.
Supply , erection testing and commissioning of Fire Fighting 4 Way Fire Brigade inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT.
Supply, erection, testing and commissioning of Air Release Valve of 20mm dia so as to release airlock in 100mm dia MS pipe at top most wet riser, ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR/ EQUIVALENT.
Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS 15683 with pressure gauge, discharge hose & control nozzie, wall mounting bracket, safety clip etc., ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT/ SAFETY FIRST / EQUIVALENT.
Supply and fixing Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS:15683., complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT.
Supply, Installation, testing and commissioning of Micro Processor based Conventional 12 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230/24 volt SMPS unit, 2 Nos. of 12 volt, 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.
Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers, (Make: Ravel / Equivalent)
Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers, (Make: Ravel / Equivalent)
Supply, Installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS junction box / false ceiling using fixing accessories llike screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers, (Make: Apollo / Equivalent)
Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.
Supply, installation, testing and commissioning of 120 Watts, 100 Volt Audio out put Amplifier having 5 Mic input& 2 Aux input, working either in 220-240 Volt, 50/60 Hz single phase AC supply or in 12 Volt DC supply, suitably mounted on wall using Mounting bracket fabricated in MS angle, Screw, Wooden plug etc., as per standard methods and as directed by the department officers. ( Bosch / Equivalent)
Supply and runs of 2 core 1.5 sqmm multi strand shielded Copper Cable for PA wiring between PA console and PA speaker provided in respective Zone existing 20/25mm dia PVC pipe as per standard methods and as directed by the department officers.
Supply and laying of 25mm dia PVC conduit Pipe in wall or Ceiling using suitable size GI mounting bracket, anchor Fateners,nylon strap etc., as per standard methods and as directed by the department officers.
Supply, installation, configuration, programming, customisation, testing and commissioning of 1/2.8"/2MP CMOS, ICR, 1920x1080:30fps, H.265/H.264/MJPEG, triple streams, DC12V & POE , fixed lens(2.8mm, 4mm, 6mm optional), smart functions, IR range upto 30m, digital defog, IR anti-reflection window, UL approved.
Supply, installation, configuring, customizing, testing and commissioning of 32 channel 320Mbps n with 1920x1080 resolution, pluggable HDDs upto 2 SATA Harddisks, supports HDMI/VGA output, ANR technology, RJ-45 self adapative ethernet interface with optional LCD display. The NVR shall have RS-232, RS-485 interface, accurate retrieval, instant playback, 30 days memory backup. (code 34- M-2198)
Supply and installation of 6TB SATA harddisk for NVR. (MAKE: Western/ Digital/ Equivalent) ( code 38 M-2222)
Supply and installation of CAT-6 I/O socket with camera back box. Code 37 M-2216.
Supply and installation of 42" monitor having large format display with HDMI.
Supply and installation of 24 Port PoE switch with all the accessories. (MAKE: D-Link/ Equivalent) code 33 M-2194
Supply and installation of 24 Port patch panel (Fully loaded) with all the accessories. (MAKE: D-Link/ Equivalent) code 40 M-2236.
Supply and installation of Patch cord - 1 Metre Length with all the accessories. (MAKE: D-Link/ Equivalent) code 40 M-2232
Supply and installation of 12U rack with all necessary accessories. (MAKE: D-Link/ Equivalent) code39 M228
Supply, installation, testing and commissioning of enhanced unarmoured Cat 6 cable. UNIT code 28 M-2183
Supply, laying and concealing of 25mm dia PVC conduits(Heavy gauge) with necessary specials and other materials inlcuding all the accessories like clamps, saddles, pull boxes for CCTV wiring etc., all complete in all respects complying with relevant standard specification and as directed by the departmental officer.
Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End ) (SD 311)
Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End (SD 313)
Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End (SD 355)
Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End. (SD 365)
Supply and fixing of single box type Havells Dura Battern LED 4' 40W LED Wall fitting complete with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting. (Data- A)
Supply and fixing of single box type Havells Dura Battern LED 4' 40W LED Wall fitting complete with TW round blocks Suspension from the ceiling Using Aluminium Pipe with PVC unsheathed Copper leads from terminals to the fitting. (Data- B)
Supply and fixing of PLUTO NEO 2X2-PLR-42W-LED840S Havells make Recess fitting with Necessary connection.(Data-C)
Supply and fixing of Havells- TORUS 600RDP/ S25W LED 857S PM MAWH Circular Fitting with its Mounting Kits to fixn on the ceiling with Necessary Connection. (Data-D)
supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting . (SD 535)
supply and fixing of 30W LED street light fitting with LED (Lower end) with 25mm dia. GI pipe (class B) with 1 no.25mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .(SD 534)
supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD 528)
Supply and fixing of Havells-HEXAFT10WLED857SSYMBOPC WTBH Fitting IP-66 on wall with 6”x6” Sintex Junction Box with Backlite connectors with necessary Connection. (Data-E )
Supply and fixing of Havells-CORAL LED POST TOP-CORAL PT 25W LED 757 PSYMTOPC Gate light fitting with 65mm Dia Gi pipe for mounting the Fitting on the gate with Control gear Box with 1 No 6A SP MCB with connection. (Data-F)
Supply and fixing of 65mm (2-1/2") GI pipe (Class 'B') of 6 metre length 6 Metre Length Double Bracket Pole with Base Plate (250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 6000mm Length with concreting with construction of masonary pedestal with suitable MS box to houseand supply and fixing of 2 Nos 48W LED street light fitting with LED (Higher end) with Control Gear Box with 2 Nos 6A SP MCB’s with Necessary Connection.(Data-G)
Supply and fixing of 65mm (2-1/2") GI pipe (Class 'B') of 6 metre length 6 Metre Length Double Bracket Pole with Base Plate (250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 6000mm Length and Additional Single Bracket to Mount 3 Nos Light with concreting with construction of masonary pedestal with suitable MS box to houseand supply and fixing of 3 Nos 48W LED street light fitting with LED (Higher end) with Control Gear Box with 3 Nos 6A SP MCB’s with Necessary Connection.(Data-H)
Supply and fixing of 7 Metre Length Single Bracket Pole with Base Plate (250 x 250 x 6mm) 114.30mm OD x 5.40mm Thick x 4000mm Length, 88.90mm OD x 4.85mm Thick x 1500mm Length, 76.1mm OD x 3.25mm Thick x 1500mm Length with concreting with construction of masonary pedestal with suitable MS box to houseand supply and fixing of 1 No 80 W LED street light fitting with LED (Higher end) with Control Gear Box with 1 No 6A SP MCB’s with Necessary Connection.(Data-I)
Supply and fixing of 4M LED Foot Light Havells Make concealed in wall with Connection. (Data- J)
Supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 300mm down rod on the existing fan clamp (SD 577)
Supply and fixing of 375mm (15") sweep (light duty) AC exhaust fan complete without provision of holes in the wall. (SD 117)
Supply and fixing of louvers shutters arrangements for 375mm (15") sweep light duty AC Exhaust fan (SD 121)
Supply and fixing of the almonard Make 400MM Wall Mounting Fan. (Data-K)
Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections. Higher End (SD 484)
Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (SD 140)
Supply and fixing of 3 nos.6A two module 5 pin socket , 3 nos. 6A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections. Higher End (SD 472)
Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 57)
Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour. (SD 424)
Supply and Run of 3 Core 2.5 Sqmm Copper Cable through PVC pipe concealed in wall. (Data- L)
Supply and fixing of Double Pole 6A to 32A, 10KA, with Suitable MS Enclosure Concealed in Wall with Connection. (Data-M)
Supply and fixing of Street light controller Panel, made up of 18 SWG MS sheet of Size Back 2.0' x 1.5' x 1’ for MS Box with Door and Hinges and Lock and Key Arrangement, comprising the Following such as L&t 4 Pole Contactor MCX-3 32A, Havells 24 Hour Analog Time Switch DHTED30016, 40A FP MCB Isolator and3 Nos of 32A DP MCB’s with 4.0 Sqmm Copper wire for Control Wiring and painting with one coat of red oxide and 2 coats of synthetic enamel paint. With Necessary Connection. (Data-N)
Supply and laying of 2 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (SD-198 )
Supply and laying of 4 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely wit h bricks and sand and refilling the earth to make good (SD-202
Supply and laying of 3 ½ x50 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (SD-206 )
Supply and clamping of 2 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps (SD 220)
Supply and clamping of 4 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps (SD 220)
Supply and clamping of 3 ½ x25 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps (SD 222)
Supply and clamping of 3 ½ x50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps(SD 224)
Supply and clamping of 3 ½ x185 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps (SD 224)
Supply and fixing of brass cable gland for 2 x 10 sq.mm. PVC armoured LTUG cable with earth connection (Data-G)
Supply and fixing of brass cable gland for 4 x 10 sq.mm. PVC armoured LTUG cable with earth connection (Data-G)
Supply and fixing of brass cable gland for 3 ½ x25 sq.mm. PVC armoured LTUG cable with earth connection (SD-186)
Supply and fixing of brass cable gland for 3 ½ x50 sq.mm. PVC armoured LTUG cable with earth connection (SD-188)
Supply and fixing of brass cable gland for 3 ½ x185 sq.mm. PVC armoured LTUG cable with earth connection (SD-193)
Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete. (SD 235)
Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete. (SD 237)
Supply and providing cable end termination of 3-1/2 x 185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete. (SD 242)
Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with 1No 32A DPMCB as incoming and 8 Nos 6Amps to 32Amps SPMCB `outgoing oncealed in Wall with earth connection only. (DATA-P)
Supply and fixing of 12 way Hager IP43 Double Door DB 12 way, 12 modules MCB sheet steel enclosure distribution board with 1No 32A DPMCB as incoming with 40 Amps 30 MA DP RCCB and 10 Nos 6Amps to 32Amps SPMCB `outgoing concealed in Wall with earth connection only. (DATA-Q)
Supply and fixing of Vertical type 4 way triple pole neutral MCB distribution board with Metal/Acrylic Door cover with IP42 Protection, 40 A FP MCB as incoming with, 12 Nos 32A SP MCBs are Outgoing on wall with angle iron frame work with earth connection only.The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager make)(Data-R)
Supply and fixing of Vertical type 4 way triple pole neutral MCB distribution board with Metal/Acrylic Door cover with IP42 Protection, 63 A FP MCB as incoming with, 12 Nos 32A SP MCBs are Outgoing on wall with angle iron frame work with earth connection only.The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager make) (Data-S)
Supply and fixing of Vertical type 6 way triple pole neutral MCB distribution board with Metal/Acrylic Door cover with IP42 Protection, 63 A FP MCB as incoming with, 6 Nos 32A TP MCBs are Outgoing on wall with angle iron frame work with earth connection only.The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager make) (Data-T)
Supply and fixing of Vertical type 6 way triple pole neutral MCB distribution board 6 Way TP MCCB DB HagerVYV06DM- with Legrand MCCB DPX160-125A, 25KA, 4P as incoming with Rotary Handle 420160 Direct and 4P Spreader Link and 6 Nos 63A TP MCB Hager NDN263N are outgoing on wall with Cable Adopter Box with Section Plate on angle iron frame work with earth connection only.The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager L &T make). (Data- U)
Supply and fixing of Vertical type 8 way triple pole neutral MCB distribution board 6 Way TP MCCB DB HagerVYV06DM- with Legrand MCCB DPX160-125A, 25KA, 4P as incoming with Rotary Handle 420160 Direct and 4P Spreader Link and 8 Nos 63A TP MCB Hager NDN263N are outgoing on wall with Cable Adopter Box with Section Plate on angle iron frame work with earth connection only.The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager L &T make). (Data- V)
Supply and fixing of Vertical type 8 way triple pole neutral MCB distribution board 250A MCCB 8 Way TPDB No:507756 with Legrand DPX 250,36 KA, 4P, No:420249 OL/SC protection as incoming with Rotary Handle 420160 Direct and 4P Spreader Link and 5 Nos 63A TP MCB Hager NDN263N, 3 Nos 100A Triple Pole MCB’s are outgoing on wall with Cable Adopter Box with Section Plate on angle iron frame work with earth connection only.The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager L &T make). (Data- W)
Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.(SD 233)
Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection ( SD 458)
Supply Erection ,testing and commissioning of 11KV, 25KA, 630Amps HT OUTDOOR SINGLE PANEL VACCUM CIRCUIT BREAKER For Consumer POS With 18KV, 10kA Polymer Type Surge Arrester. Horizontal Draw Out VCB fitted with Manual / Motor Operated spring charging mechanism with 230V AC Motor & Motor Control Switch, Mechanical ON / OFF indicator Operation Counter, Automatic safety shutters & push Shunt trip Coil, 110V DC. Closing Coil, 110V DC. Spare auxiliary contact, 6NO + 6NC. Anti pumping Feature, 110V DC. Power pack 230V-110V AC / 110V DC Potential Transformer, Three Phase, Resin cast, Dry type, Fixed Potential transformer with one set of HTFS / LTFS and one no. Neutral Link of Ratio : (11KV/√3) / (110V/√3) Current Transformer, Single phase, Resin Cast, Dry Type Current Transformer, Core 1: for meter, Cl-0.5s, 5VA, Core 2: for protection, Cl-5P20, 15VA. Metering, MFM, Digital Ammeter & Digital Voltmeter With Fault Level tripping & Fault Recording. Protection, Numerical Non-directional IDMT combined 3 O/C+1 E/F relay, High speed / Master trip relay, Indication Lamps, All LED Lamps, VCB OFF/ON/Auto trip/Trip circuit healthy/Spring charge indication lamps, R,Y,B Phase Indication Lamps. Heater ON / OFF switch with filament type 200Watts space heater & thermostat , single phase switch with socket, 40W cubicle Lamp for panel illumination with snap type door limit switch, Fuses/MCBs for AC/DC control. Cable Entry In and Out should be Separate Chamber MS Sheet steel enclosure & installation with paint shade of RAL 7032 suitable for outdoor.(Data-A) Heater ON / OFF switch with filament type 200Watts space heater & thermostat , single phase switch with socket, 40W cubicle Lamp for panel illumination with snap type door limit switch, Fuses/MCBs for AC/DC control. Cable Entry In and Out should be Separate Chamber MS Sheet steel enclosure & installation with paint shade of RAL 7032 suitable for outdoor.(Data-A)
Construction of HT Cable Trench with the following steps. 1. Earth work excavation 2. Cement Concrete 1:4:8using 40MM Guage HBGSnot more than 15CM thick with standard Specification. 3. Brick work in 1:5 Cement Mortar using Chamber burned bricks of size 9”x4-3/8x2-3/4 with standard Specification. 4. Plastering with cement mortar1:512mm Thick in all areas with standard Specification. 5. Supply and fixing MS Grills cover slab on top of the Trench. ( Data-C )
Supply and laying of 11KV 3 Core 240 Sqmm XLPE UG cable in a existing trench from TNEB pole to 3 Panel Metering VCB. (Data-D)
Supply and clamping at 11KV 3 core 240 sq.mm XLPE UG cable in Existing Trench or on wall with M.S. special clamps (3 panel HT VCB Incoming to SinglePanel VCB and to Transformer) (DATA-E)
Supply and providing cable end termination suitable for 11KV 3 core 240 sq.mm XLPE HTUG cable with necessary outdoor type heat / cold shinkable joint kit and accessories (Make:RayChem/M.Seal.(TNEBPole) (Data- F )
Supply and providing cable end termination suitable for 11KV 3 core 240 sq.mm XLPE HTUG cable with necessary indoor type heat / cold shinkable joint kit and accessories (Make:RayChem/M.Seal) (Data-G )
Construction of Transformer Yard as concrete bed for the size of 14Mt x 8.0Mt with the following procedures . 1. Earth work Excavation 2. Filling M-Sand 150MM 3. Cement Concrete 1:5:10 150mm 4. Design Mix M20 Concrete Below Basement. 5. Design Mix M20 Concrete Above Basement. 6. MS RTS rod for all RCC Works. 7. Centring for all sides. 8. Brick work using Chamber burnt bricks. 9. Plastering work for all round. (Data-H)
Fencing for protection arrangements to the transformer yard. Supply and providing HT yard link fencing with fixing of 11ft height in MS Square pipe of size 3'' X 3'' by excavated the earth with depth of 3ft putting concrete and refilling the earth to make good and fixing of chain link fencing with size of (2" X 2")X 10SWG galvanized iron wire fixing of 7'* 8' Square MS Angle in box type frame all around the HT yard with necessary binding wire with 8Nos ISI earthing RCC pillar with chain link fencing should be provided for the total area of 8 Mtr X14Mtr.and with One No Entrance Gate. Earthing the fencing by using no.8 SWG copper wire all around the fencing. (10+5)x2x7 = 210 Sqmt ) (MR]
Supply and fixing of HT Metering box made of 16SWG CRCA Sheet steel as per TNEB / IER specification with earth connection on the existing 3 Panel VCB suitable masonry with armored copper cable from HT CT coil box, 2.5 sqmm PVC unsheathed SC copper conductor of 1100V grade 4colours Red, Yellow, Blue and Black 15mtrs each with termination kits for M.R.T use, copper holders complete as required for TNEB HT side metering as instructed by the site officers complete with painting of suitable colour. ( MR)
Supply erection ,testing and commissioning of 500KVA/11KV /433V copper wound outdoor type distribution transformer conforming to relevant ISI 1180 Level -2 standard and fitted with the following : a)HV cable end box suitable for Connection 3 core 240 Sq mm 11 KV , XLPE HT cable b) LV cable end box suitable for connection 3 runs of 31/2x400 Sq mm LTUG Cable c)Conservator with shut off valve d) Conservator drain plug valve e) Dehydration silica gel breather (f) Expansion vent g) 4Nos plain rollers H) Thermometer pocket with dial type thermometer with caillary tubing with maximum reading position i) Drain plug/ valve ) Filter valve j) Oil filling hole and cap k) Oil level gauge l) two body earthing terminals m) Rating and terminal marking plate n) Lifting hooks / lifting eyes ,jacking pad to facilitate movement of transformer and easy handling1No(Each) n) OFF load hand operated tap changing switch at standing height from ground level p)Neutral on LV side to be available for 4 wire supply and brought out thought bushing for earthing q)Air release device r)The transformer should be supplied with first filling of oil All removable cover shall be provided with weather proof hot oil from the tank Rowson /Voltech /IPL )/3Si /eq ( Data-I)
Supply and Clamping of 3 Run x 31/2 x 400 sq.mm PVC armoured LTUG cable in a existing Trench and covering the cable completely with MS Grill Slab. (Data- K)
Supply and fixing of brass cable gland for 3½X400 Sq.mm PVC armoured LTUG cable with earth connection. ( SD- 196 )
Supply and providing cable end termination of 3½X400 Sq.mm PVC LTUG aluminium armoured cable with necessary aluminium cable socket by crimping etc., with electrical connection complete. (Data- L)
Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection. (SD-76)
Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection. (SD-77)
Supply and Errection of safety items. 1) 2mx1mx20mm thick 11 kv grade rubber mat-- 20nos 2) 9 litter fire bucket 4nos with stand --2 set 3) 5 kg cappacity dry powder type fire extinguisher--8 nos 4) Rubber hand gloves11 kv---1pair 5) First aid box with medicine--1 set 6)First Aid Chart Tamil-1No &English-1No=2Nos 7) Earth discharge rod with 5 mts 8 AC Chargeable Emergency Lamp 2 x 11W PL Lamp with all connected accessories 9) Danger Board as required by the Electrical Authorities. (Data- M)
Supply and installation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp. (SR-M-2144)
Supply and Laying of 3 Run x 31/2 x 400 sq.mm PVC armoured LTUG e in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good Re-filling of earth: (Data- J)
Supply , Erection Testing and commissioning of 415V/50 HZ 800A Cubicle panel board with Panel Size 10’(L)x 6’(H) x 3.3’(W) with centre switches Chamber the bus bar chamber and cable chamber with 16 SWG thick CRCA sheet with 100Mm x 50MM x 6MM MS channel for base Support with 2”x ½ ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the the panel board for earth buses and with MFM 4405 LED meter Cl_1, 3 Line Digital MFD meter with RS -485 Connection, with one set of LED pilot lamps set with fuse base, top & 10A HRC fuse link for 3 phases on a separate chamber and with the following switches complete. 800A ACB Draw out C-Power EDO 65KA (LNT : SL96072) L&T Make with EFR release module SL91340OOOO (Incoming) - 1 No 1. 400 Amps FP MCCB L&T make –2 nos. 2. 250A FP MCCB L&T Make -3 Nos 3. 320A FP MCCB L&T make- 2 Nos 4. 125A FP MCCB L&T Make- 2 Nos with 1 No Metallic danger board with powder coated painting, necessary identification of outgoing loads, bus capacity, cable size etc., with bold letter (Data- N)
Supply , Erection Testing and commissioning of 415V/50 HZ 320 A Cubicle panel(MAIN Panel) board with Panel Size 8’(L)x 5’(H) x 2’(W) with centre switches Chamber the bus bar chamber and cable chamber with 16 SWG thick CRCA sheet with 100Mm x 50MM x 6MM MS channel for base Support with 2”x ¼ ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the the panel board for earth buses and with MFM 4405 LED meter Cl_1, 3 Line Digital MFD meter with RS -485 Connection, with one set of LED pilot lamps set with fuse base, top & 10A HRC fuse link for 3 phases on a separate chamber and with the following switches complete. 1. 320 Amps Four Pole MCCB L&T Make with UV Release(Incoming) - 1 No 2. 125 Amps Four Pole MCCB L&T-8 Nos 3. Selec Make MFM383A-C Multifunction energy meter 3 phase – 1 No with 1 No Metallic danger board with powder coated painting, necessary identification of outgoing loads, bus capacity, cable size etc., with bold letter. (Data- O)
Supply and Erection of 320A ATS Control Switch with Suitable Enclosure L&T Make Enclosed ATS, Frame 3, 315A- , CK90165BSOO with V/OV, Phase Sequence, Single Phasing, Frequency • Authorized Access Control through Password Protection • Terminal Shrouds, Phase Barriers & Source Separator Convenience Safety with necessary Connection. (Data- P)
Supply and Erection of Outdoor Pillar Box Made up of 16 SWG MS Sheet with Panel Size 3’(L)x 3’(H) x 1.5’(W) with sturdy support of 100Mm x 50MM x 6MM MS channel and to be fixed on the ground with Concrete plinth Concreting and masonry work for fixing the Pillar Box with Secure Lock and keys for accommodating AC Outdoor Panel to be erected on the Terrace. (Data-Q)
Supply, erection, testing ,and commissioning of 160 KVA Diesel Silent Generator set,0.8 PF 3 Ph, 415V, 50 Hz with AMF Panel as Detailed below. A.Engine: Water cooled Diesel Engine type suitable for generating application with a Shaft output of suitable capacity of 241 BHP at 1500 RPM unde NTP conditions. As per the BSS 5414 / ISO 3046 The Engine Shall comprise the following standard Fittings. (Kirloskar / Cummins / Equivalent )B.Alternator: Capacity fo 160 KVA / 128 KW, 0.8 PF self excited,self regulated design to run at 1500 RPM under NTP condition confirming to BS 5000 / IS 13364(part II) 1992 to be coupled directly to the Diesel Engineand Test Certificate. (Kirloskar / Stamford / equivalent) C. Battery: 1 No 12V 150 AH Battery with copper leads and terminals., Battery Make EXIDE/AMCO/AMARON I. Acoustic Enclosure: Supply of acoustic Enclosure for 160 KVA Diesel Generator Set. The Acoustic enclosure is made of 1.6 / 2 mm thick CRCA sheets in munsel Green shade and a Structural Sheet metal base frame Painted in Black. The walls of the enclosure are insulated with fire retardant foam so as to comply with the 75 dBA at mtr sound levels specified by Ministry of enforcement. The enclosure should be complete with 1. Arrangement for power cable for connection. 2. Residential exhaust silencer,with flexible base arrangements. 3. Suction louvers. 4. Discharge Louvers. 5. Open able and lockable doors on both sides with air tight Neoprene rubber gasket. 6. Interior lighting arrangements. 7. Lifting arrangements. J. Erection, Testing and Commissioning of the genset comprising the following: 1. Providing suitable concrete foundation with plain cement concrete 1:2;4 with sand cushion all around the foundation suitable for mould engine and alternator with acoustic enclosure. 2. Erection of generator set complete with acoustic enclosure ,fuel tank, engine control Panel, standard control Panel, base frame complete on the above foundation and lifting arrangements. First charging of lub oil and first charging of Battery. (M-2082)
Supply and laying of 3 ½ x 240 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. (SD-212)
Supply and clamping of 3 ½ x 50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps. (SD-230)
Supply and fixing of brass cable gland for 3 ½ x50 sq.mm. PVC LTUG aluminium armoured cable with earth connection. (SD-194)
Supply and providing cable end termination of 3-1/2 x 240 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.(Data-R)
Supply, Erection, Testing, Commissioning and Handing over of 13 Persons Capacity Passenger Lift (with Machine Room) as per following technical specifications including all taxes and duties. Technical Specifications: 1. Location: Cultural Centre, Chennai 2. No of Lift: 2 Nos 3. Type of Lift: Passenger cum Stretcher 4. Capacity of Lift : 13 Persons Passenger (680 Kgs) 5. Speed: 1.00 mtr /Sec 6. Type of Drive: Microprocessor based specific variable voltage variable frequency V3F Drive with enhanced ride comfort and near zero leveling functions. 7. No of floor: Ground + 3 floors . 8. Total Travel: 11.0 Mtrs Approximate. 9. Leveling Accuracy: High level accuracy with smooth & Jerk free stopping. 10. Construction of car: Special car made of Stainless Steel Hairline finish No.4 hair line finish & panels with direct lighting and new beautiful single tile false ceiling with tubular handrail and mirror. 11. Position of Machine: Directly above the lift well. In Machine Room 12. No. of Landing Entrance: One in front 4 Nos only. 13. No. of Car Entrance: One in front only. 14. Car Entrance Door: Centre opening automatic power door with stainless steel No.4 Hair Line finish with view panel. 15. Landing Entrance Door: Center opening automatic power door with stainless steel No. 4 hair line finish with view panel. 16. Lift well : 2500mm (width) x3000mm(depth) available size. 17. Lift pit depth available: 1600mm 18. Car size: 1600mm wide x 1350 mm deep x 2300mm Height (Part I) – 2000). 19. Car clear Opening: 900 mmX2100 mm (as per IS 14665 (Part-I) – 2000). 20. Lift Machine Room : As per standard specification. 21. Power Supply: 415v, 3 phase, 50 Cy /Sec A.C supply for power and 230 V, 50 Hz single phase AC supply for light. 22. Control: Micro processor Computer based – simplex collective full collective logic system with/without attendant mode. 23. Car fittings4 Nos 8W LED recess Mount Fixture Lighting with cross flow fan 24. Lift Well: RCC construction with Brick masonry. 25. Indication: Up/Down Digital Direction scroll type and position indicator for all landing and in car. 26. Emergency Alarm Bell: BatteryOperated Alarm Bell to be provided with automatic charging device. 27. Emergency Light: Battery operated Light to be provided with automatic charging device. 28. Fireman’s switch: To be provided at ground floor. 29. Minor Builders Work: To be provided by lift contractor. 30. Scaffolding: To be provided by lift Contractor. 31. Stainless Steel sill angles and facia Plates: To be provided by lift contractor. 32. Steel for lift Machinery: To be Provided by lift contractor. 33. Servicing and Maintenance: Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year.34. Provision of 1+3 EPABX intercom with phone to be provided at the following Places,vide 1.Lift Head Room,2. Reception Room and 3. Inside the Lift, by lift contractor. 35. Lift License: Preparation of drawing, Payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate and lift license as per lift act should be done by lift contractor. 36. Automatic rescue device – To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charges inverter ,under voltage protection system etc 37. Floor annunciation system with music. 38. Special futures: (a). Infra red door sensor with Full height screen. (b). Full width half height rear panel Mirror. (c).Voltage stabilizer for circuit control. (d). Tubular Stainless Steel hand rail Three sides in car. (e). Signal Fixtures (f). VandalproofS.S.buttonwith S.S. cover. (g). Stainless steel door frames (h). V3F door operator (i) Call register signal (j) Pit ladder (k). Braille buttons (l).Stainless steel facia for car operating panel and landing fixtures. (m). ON-OFF switch for fan and Light (n) Over load warning indicator. (O) Fire rating : 60 Mins. Over speed governor, phase failure and phase reversal relay, alarm bell, Guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs, car safety gears, buffer, electro mechanical door locks, emergency key, side supporting angles, motor over load protection devices, final limit switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries. 39. Guarantee: Guarantee for the Materials& workmanship of equipments complete should be offered by the Lift firm for a period of not less than one year. 40. Site testing in accordance with IS 14665 should be carried out at the time of handing over .
Supply, Erection, Testing, Commissioning and Handing over of 1 No 1500 Kg Capacity Goods/Service Lift (with Machine Room) as per following technical specifications including all taxes and duties. Technical Specifications: 1. Location: Cultural Centre, Chennai 2. No of Lift: 1 No 3. Type of Lift: Goods/Service Lift 4. Capacity of Lift : (1500 Kgs) 5. No of Stops/Opening: 4 / 4 6. Rated Speed: 1 Mt/Sec 7. Floor Design: Ground +3 Floors. 8. Access: 2 on Opposite Side in Ground 9. Shaft size: 2600 x 2470mm 10. Overhead: 4800 mm 11. Pit Depth: 1800 mm 12. Travel Height: 12 Mts Approximate. 13. Pit Ladder: Yes 14. Car Size: 1650 x 2080 mm 15. Car Clear Height: 2350 mm 16. Car Door Type: Power operated Centre opening slide Door. 17. No of Door Panels : 2 Panel. 18. Car Door Size: 1100 x 2000 mm. 19. Rear Car Door Type: Power operated Centre opening slide Door 20. Construction of car: Special car made of Stainless Steel Hairline finish No.4 hair line finish & panels with direct lighting and new beautiful single tile false ceiling with tubular handrail and mirror. 21. Position of Machine: Directly above the lift well. In Machine Room 22. Lift Machine Room : As per standard specification. 23. Power Supply: 415v, 3 phase, 50 Cy /Sec A.C supply for power and 230 V, 50 Hz single phase AC supply for light. 24. Control: Micro processor Computer based – simplex collective full collective logic system with/without attendant mode. 25. Car fittings4 Nos 8W LED recess Mount Fixture Lighting with cross flow fan 26. Lift Well: RCC construction with Brick masonry. 27. Indication: Up/Down Digital Direction scroll type and position indicator for all landing and in car. 28. Emergency Alarm Bell: BatteryOperated Alarm Bell to be provided with automatic charging device.29. Emergency Light: Battery operated Light to be provided with automatic charging device. 30. Fireman’s switch: To be provided at ground floor. 31. Minor Builders Work: To be provided by lift contractor. 32. Scaffolding: To be provided by lift Contractor. 33. Stainless Steel sill angles and facia Plates: To be provided by lift contractor. 34. Steel for lift Machinery: To be Provided by lift contractor 35. Servicing and Maintenance: Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 36. Provision of 1+3 EPABX intercom with phone to be provided at the following Places,vide 1.Lift Head Room,2. Reception Room and 3. Inside the Lift, by lift contractor. 37. Lift License: Preparation of drawing, Payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate and lift license as per lift act should be done by lift contractor. 38. Automatic rescue device – To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charges inverter ,under voltage protection system etc. 39 Floor annunciation system with music. 40. Special futures: (a). Infra red door sensor with Full height screen. (b).Voltage stabilizer for circuit control. (c). Tubular Stainless Steel hand rail Three sides in car. (d). Signal Fixtures (e). Stainless steel door frames (f). V3F door operator (g) Call register signal (h). Braille buttons (i).Stainless steel facia for car operating panel and landing fixtures. (j). ON-OFF switch for fan and light. (k) Over load warning indicator Over speed governor, phase failure and phase reversal relay, alarm bell, Guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs, car safety gears, buffer, electro mechanical door locks, emergency key, side supporting angles, motor over load protection devices, final limit switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries. l. Guarantee: Guarantee for the Materials& workmanship of equipments complete should be offered by the Lift firm for a period of not less than one year. 44. Site testing in accordance with IS 14665 should be carried out at the time of handing over . k. As per site condition, The lift should have double door (on Either Side ) for Loading.
Supply and installation of Modular type outdoor units equipped with highly efficient DC twin Rotary compressors with all inverter type compressor(s) only, special acryl pre coated heat exchanger, low noise condenser fan, auto check function for connection error, auto address setting, with multiple outdoor units of capacities and quantities as mentioned below. Refrigerant Shall be R410A.
20 HP Outdoor Unit
22 HP Outdoor Unit
24 HP Outdoor Unit
26 HP Outdoor Unit
Indoor Units for the above outdoor unit High Static Ducted indoor units with compact cooling coil,electronic expansion valve and multispeed fan motor,The blower shall be dynamicaly balanced and designed for silent operation.
3.0 Ton Indoor Unit
5.8 Ton Indoor Unit
7.15 Ton Indoor Unit
8.0 Ton Indoor Unit
11.4 Ton Indoor Unit
12.8 Ton Indoor Unit
Supply and fixing of Y & T JOINTS
Supply and fixing of wired remote for Indoor Unit
Supply and fixing of duct mouth damper
Supply and fixing of flexible convass connection
supply ,fabrication and fixing of suitable MS angle support frame for indoor units.
supply ,fabrication and fixing of suitable MS angle support frame for VRF Outdoor units
Supply ,fabrication and fixing of fresh air louver made of extruded aluminium with bird screen provided with intake louver
Supply and fixing of Fabrication and erection of 20SWG Galvanised Sheet Steel ducting with necessary ‘u’ supports.
Supply and fixing of Fabrication and erection of 22SWG Galvanised Sheet Steel ducting with necessary ‘u’ supports
Supply and fixing of Fabrication and erection of 24SWG Galvanised Sheet Steel ducting with necessary ‘u’ supports
Supply of extruded aluminium powder coated Gravity Louvers
Supply and fixing of extruded aluminium powder coated supply and return air grills/diffusers with volume control damper
Supply and providing thermal insulation of 9mm thick vidoflex with Aluminum Foil
Supply and providing acoustic for initial portion of ducting with 12mm thick Fibre Glass Rigid Board covered with Tissue Paper and Aluminum Perforated Sheet
Pressure Testing & Commissioning of VARIABLE REFRIGERANT VOLUME/FLOW SYSTEM of below mentioned capacities comprising of Inverter Compressor and complete with the following.100% FULLY INVERTER COOLING MODEL
20 HP Outdoor Unit
6 Nos 22 HP Outdoor Unit
24 HP Outdoor Unit
26 Hp Outdoor Unit
Testing and commissioning of VRF Indoor units and Ductable Indoor unit
Supply, installation, Testing & Commissioning of hard/Soft drawn soft refrigerant piping with refnet joints. The brazing to be carried out with bleeding of nitrogen. The copper pipe to be insulated with 19mm thick for suction and 13mm thick for liquid line with class O make( All Copper pipes to be covered with micropolyshield coating, Drier/filter and shutoff valves to be installed in liquid line of the outdoor unit)
41.3 mm; 34.9 mm ;28.6 mm ;22.2 mm ;19.1 mm ; 15.9 mm ;12.7 mm ;9.5 mm ;6.4 mm
Supply and laying of Control Cabling PVC insulated copper conductor control cables 3Cx1.5 sqmm,as per relevant IS.
Supply and laying of Control Cabling PVC insulated copper conductor control cables 3Cx2.5 sqmm,as per relevant IS
Supply ,Providing and fixing in position drain piping the 25.4 MM PVC pipes for drain to required lengths and installed complete with all necessary fittings like elbows, tees & reducers.
Supply and providing of pipeline nitrle rubber 13mm insulation for drain pipe lines
Supply and providing under duct insulation with 19mm XLP
Supply of Refrigerant gas topping at site for VRV/VRF
Towards the charges for Scaffolding
Unit lifting shifting , positioning charges for outdoor unit
Unit lifting shifting , positioning charges for Ducted unit
Supplying and fixing of 24watts LED decorative gate light fitting philps or havells complete with suitable length 32mm dia GI pipe Class B on the existing gate piller with supply and fixing of M.S box of 30cm x 20cm x 10cm with angle iron frame work
Towards charges for preparation of drawings and CEIG approval
Sub Total
GST18% (CGST9% + SGST 9%)
SRI VENKATESHWAR ENGINEERING CONTRACTORS
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid