Providing and Fixing of Children Play Equipments, Open Air Gym, in various parks in Dhanas, Chandigarh, under WDF

Providing and fixing of swing ( 2 seater) 10’ Long 8’-6’ high & 5’-0” wide made out of 2” M.S. Pipe completed as per DRG No. 02 Job No. M-06 and to the Entire satisfaction of Engineer-In-Charge

Providing & Fixing of Wide Slide SS Area : 3.9 m x 1.3 m Safe Play Area : 4.9 m x 2.3 m Platform Height : 1.2 m The Wide Slide on of the attractive slides of its kind. The chute is made up of 14 SWG SS/GI Sheet. The stainless steel used is of 304 grades. The chute is supported by 40X5 MS angle. This chute is attached to the platform made from SS/G sheet. The platform is supported by 40 NB GI pipe. The ladder is made using 20 NB and 25 NB GI Pipes. The steps for the ladder is made are of 20 NB GI Pipes. The sliding height is 2.4m. The landing support used is made up of 25 NB pipe. The handrail of the chute is made up of 20NB power coated GI pipe. The slide is innovative wide slide on which at a time 3 kids can slide.

Providing & Fixing of Multi Activity Play System (II) (MAPS II): Deck 3’ Ht. 1 Deck 2.5 Ht. 1 FRP Staircase 3’ Ht. 1 FRP Curve Slide 3’ Ht. 1 Rainbow ladder 1 Double Swing 1 Bubble Pannel 1 Steering 1 Area: 7mX5m Safe Area: 8mX6m 1. Deck 3’ height & 2.5’ height - The Deck of MAPS is made up of 4mm thickness fiberglass reinforced plastic. The top of the platform shall be made up of anti skid surface with multicolored pigment resign. All the attachments is through nylon clamps only. The size of platform is 1.6Mx1.6M. 2. FRP Stairs case - The ladder shall be made up of the fiber reinforced plastic with a thickness of 4mm. It should have reinforcement to maintain strength and avoid bending. 3. FRP Curve Slide- It is made up of 4mm thickness fiber reinforced plastic. 4. Rainbow Ladder- It is 5’ long in height, the main frame of ladder is made up 20 NB G.I. Pipe and risers are made up of 40 NB G.I. Pipes. 5. Double Swing.-Leg Support in 40 NB G.I. Pipe and top pipe is made up of 50 NB G.I. Pipe seat is made up of 10 mm reinforced rubbers and G.I. Pipe should be rubber coated and movement with Nylon Clamps at top. 6. Bubble Panel.-The railing is providing to all decks for safety and it is made up of LLDPE. 7. Steering Wheel-It is made up of LLDPE.

Providing and fixing of Chest Press Double complete in all respects having following specifications. Size / Dimensions- Length -1200 milimeter, Width- 700 milimeter, Height – 1800 milimeter Maximum weight -120 kilogram Material:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure strength, durability, and corrosion resistance. The main central pipe shall be an 80 mm NB GI pipe, while the handle frame and sheet frame shall each consist of 40 mm NB GI pipes. The connecting links shall be made of 32 mm NB GI pipes, and the footrest pipe shall also be 32 mm NB GI. The mild steel (MS) foundation plate shall have a minimum thickness of 12 mm. The foundation pipe shall consist of a GI pipe anchored 750 mm deep and supported with an MS angle of 25×25×4 mm for stability. The seat and backrest shall be made of high-density polyethylene (HDPE) sheets with a thickness of 3 mm, designed with a uniform bending radius to avoid sharp edges and ensure user safety. All nuts and bolts used for assembly shall be made of galvanized iron (GI) to enhance durability and resistance to corrosion. The movement mechanism shall be fitted with ball bearings that are self-lubricating and sealed to protect against rain, dust, and other environmental elements. The closing caps of open ends of all pipes, as well as bearings, bushes, and bases, shall be covered with fibre-reinforced plastic (FRP) closing caps having a minimum thickness of 3 mm. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions. Colour:- Green, Paint finish- Power coated, UV resistant, Paint coating thickness (min) – 100 micrometer, Warranty - 3 years. Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge.

Providing and Fixing of Parallel Bars complete in all respects having following specifications. Size/Dimensions- Length- 900 millimeter, Height – 800 millimeter Material:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure strength and durability. The vertical or standing pipes shall be 40 mm NB with a thickness of 2.9 mm, and the horizontal pipes shall also be 40 mm NB with a thickness of 2.9 mm. The foundation pipe shall consist of a GI pipe anchored 500 mm deep and supported with a mild steel (MS) angle of 25×25×4 mm. The nominal bore of the foundation pipe shall be 40 mm NB with a thickness of 2.9 mm. The MS foundation plate shall have a minimum thickness of 12 mm. All nuts and bolts used for assembly shall be made of stainless steel to provide durability and resistance to corrosion. The open ends of all pipes, bearing bushes, and bases shall be fitted with fibre-reinforced plastic (FRP) caps having a minimum thickness of 2 mm. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance under outdoor conditions. Colour:- Paint finish- Power coated, UV resistant, Paint coating thickness (min) – 80 micrometer, Warranty - 3 years. Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing of Three wheel shoulder Builder/ Arm wheel- outdoor Gym Equipment complete in all respects having following specifications. Size / Dimensions Height of central Pole from ground -1524 millimeter Outside diameter of first wheel - 850 millimeter Outside diameter of second wheel - 800 millimeter Outside diameter of third wheel - 650 millimeter Height of first wheel from ground - 1220 millimeter Height of second wheel from ground - 1200 millimeter Height of third wheel from ground - 1180 millimeter Maximum weight -120 kilogram Material:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure quality and durability. The main central pipe shall be constructed using a 125 mm NB GI pipe, while the ring (wheel) shall be made of a 40 mm NB GI pipe. The spokes of the wheel shall consist of 15 mm NB GI pipes, with a total of six spokes per wheel. The foundation pipes shall be GI pipes anchored 750 mm deep, supported with mild steel (MS) angles of 25×25×4 mm, and shall have a nominal bore of 125 mm. The MS foundation plate shall have a minimum thickness of 12 mm. All nuts and bolts used for assembly shall be made of stainless steel to ensure durability and resistance to corrosion. The movement mechanism shall be equipped with ball bearings, which shall be self-lubricating and sealed to provide protection against rain, dust, and other environmental factors. The open ends of pipes, bearings, bushes, and bases shall be fitted with high-density polyethylene (HDPE) closing caps having a minimum thickness of 2 mm. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions. Colour:- Paint finish- Power coated, UV resistant,Paint coating thickness (min) – 80 micrometer, Warranty -4 years. Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing of double Surf Board - outdoor Gym Equipment complete in all respects having following specifications. Size / Dimensions - Length -950 millimeter, Width- 700 millimeter, Height – 1300 millimeter Maximum weight -120 kilogram Material :- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure quality, strength, and durability. The main central pipe shall be made of 150 mm NB GI pipe with a thickness of 4.5 mm. The movement frame pipe shall be 32 mm NB with a thickness of 4 mm, while the connecting link pipes shall be 32 mm NB with a thickness of 2.6 mm. The handle frame pipe shall be 25 mm NB with a thickness of 2.6 mm. The foundation pipes shall consist of GI pipes anchored 500 mm deep and supported with mild steel (MS) angles of 25×25×4 mm, having a nominal bore of 100 mm. The MS foundation plate shall have a minimum thickness of 12 mm. The movement mechanism shall be equipped with ball bearings that are self-lubricating and sealed to provide protection against rain, dust, and other environmental factors. All nuts and bolts used for assembly shall be made of galvanized iron (GI) to ensure long-lasting durability and corrosion resistance. The footrest shall be made of fibre-reinforced plastic (FRP) for strength and user comfort. The open ends of all pipes, bearings, bushes, and bases shall be fitted with GI closing caps having a minimum thickness of 3 mm. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions. Colour:- Paint finish- Power coated, UV resistant,Paint coating thickness (min) – 80 micrometer,Warranty - 2 years. Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing of Air walker/Stroller Single complete in all respects having following specifications. Size / Dimensions - Length -1100 millimeter, Width- 460 millimeter,Height – 1480 millimeter & Maximum weight – 100 kg. Material:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure strength, durability, and corrosion resistance. The main frame shall be made of 100 mm NB GI pipe, while the leg movement frame shall consist of 40 mm NB GI pipe, and the handle frame shall be constructed using 32 mm NB GI pipe. The movement mechanism shall be equipped with ball bearings that are self-lubricating and sealed to provide protection against rain, dust, and other environmental factors. The footrest shall be made of high-density polyethylene (HDPE) for enhanced durability and user comfort. The foundation pipes shall be GI pipes anchored 750 mm deep and supported with mild steel (MS) angles of 25×25×4 mm. The nominal bore of the foundation pipe shall be 100 mm, while the MS foundation plate shall have a minimum thickness of 10 mm. All nuts and bolts used for assembly shall be made of galvanized iron (GI) to ensure long-lasting durability and corrosion resistance. The open ends of all pipes, as well as the bearings, bushes, and bases, shall be fitted with HDPE closing caps having a minimum thickness of 2 mm to provide a neat finish and additional protection. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions. Colour:- Paint finish- Power coated, UV resistant, Paint coating thickness (min) – 100 micrometer,Warranty - 3 years. Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing of Double Twister( One standing and One Sitting) outdoor Gym Equipment complete in all respects having following specifications. Size / Dimensions- Length -1400 millimeter, Width- 680 millimeter,Height – 900 millimeter & Maximum weight - 100 kilogram Material:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure quality, strength, and durability. The main central pipe shall be made of 100 mm NB GI pipe with a thickness of 4.5 mm. The standing/sitting twister frame pipe shall be 32 mm NB GI pipe with a thickness of 4 mm, while the rotating disk support pipe at the bottom shall be 80 mm NB GI pipe with a thickness of 3.2 mm. The handle frame pipe shall be 25 mm NB GI pipe with a thickness of 3.2 mm. The foundation pipes shall consist of GI pipes anchored 750 mm deep and supported with mild steel (MS) angles of 25×25×4 mm, having a nominal bore of 100 mm. The MS foundation plate shall have a minimum thickness of 10 mm. The movement mechanism shall be equipped with roller bearings that are self-lubricating and sealed to provide protection against rain, dust, and other environmental elements. All nuts and bolts used for assembly shall be made of galvanized iron (GI) to ensure durability and corrosion resistance. The footrest shall be made of aluminum casting for enhanced strength and stability. The open ends of all pipes, as well as bearings, bushes, and bases, shall be fitted with fibre-reinforced plastic (FRP) closing caps having a minimum thickness of 2 mm to provide a smooth finish and additional protection. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions. Colour:- Blue, Paint finish- Power coated, UV resistant, Paint coating thickness (min) – 80 micrometer Warranty - 2 years. Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge.