SPECIAL REPAIRS TO BUILDING NO P-37 OF TRG REGT AT ARTY CENTRE UNDER GR NASIK ROAD CAMP

Amount

Demolition of brick work or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillers etc but including ashlar facings, dressed stone work and precast concrete articles

M & L for Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 with old size bricks.

M & L for Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 with old size bricks.

Taking down cement plaster on brick or stone wall etc including raking out joints hacking for keys scrubbing down with water etc. including removing all the debris out side MD land

M&L for rendering 5 mm thick (1: 3) on fair faces of concrete surfaces incl preparation to new surfaces on ceilings finished even and smooth without using extra cement

M&L for rendering 15 mm thick on stone surfaces or other than fair faces of brick work or concrete surfaces in CM 1:4 rendering is to be finished even and smooth without using extra cement adding water proofing compound 3% by weight of cement (water proofing compound shall be measured and paid separately)

M&L for rendering 15 mm thick (1: 6) on stone masonry or surfaces fair faces of brickwork or concrete surfaces finished even and smooth without using extra cement

Supply only intergral water proofing compound

M&L Preparation of new plastered surfaces and applying three coats of white wash on ceiling surfaces all as directed

M & L for preparing old decorated surfaces and applying two coat of white wash on surface of ceilings.

M & L for Complete removal of existing treatment and applying 3 mm thick Birla white putty incl necessary repair and priming with alkali resistant primer coat as prepratory to applying two coats of OBD, white or tinted on walls all as specified and directed by Engr-In-Charge.

M&L for preparing plastered surfaces and applying two coats of oil bound distemper over one coat of primer including preparatory work with including and applying 3mm thick wall care putty to distempering on surfaces of walls complete all as specified and directed by EIC.

M & L for special treatment to sunken portion with (a) Clean the sunken portion of toilet/Bath/WC/Kitchen throughly to remove laitance, dirt, dust, etc. (b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar ("Dr Fixit" Pidicrete URP" or eqvt) (c) Sanitary pipes entering through walls and floor shall be sealed with "Dr Fixit Bathseal Tape" and the gaps to be grouted with non-shrink cementitous grout "Dr Fixit Bathseal Grout" or eqvt. Nahani traps, etc to be fitted securely and the gaps around it to be grouted in the same manner. (d) Apply one coat of a Bitumen-modified polymer coating "Dr Fixit Bathseal Plus" or eqvt on all angle fillets by brush and cover it with 100 mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely.(Contd...)

Item No 14 Contd..... (e) In the remaining area, in dry sustrate condition brush apply first coat of the same coating and further apply second coat when first coat is dry. Extend the coating upto 150 mm above the FFL. Above FFL, another cementitious waterproof coating "Dr Fixit Pidifin 2 K" or eqvt can be further applied right upto 2.1 mm to waterproof the shower area also, it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hours and allow to dry completely.(f) After 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed M 15 type B0 mixed with intergral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:5:10 type E2.(g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready-to -make Tile grouts of appd makes such as Dr Fixit, FOSROC SIKA, MC BUCHEMIE, ROFF, etc. Tile to be measured separatly

S&F in repairs Vitreous china squatting pan ,'Orissa' pattern, size 580x440 mm white,with integral foot rests (excluding flushing cistern and flush pipe)

S&F of PVC(SWR) 'P' trap of 125/110 mm bore

Dismantling floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premises.

M&L for 10 mm thick rendering in CM 1:4 on brick masonary or concrete rough finished surfaces as backing coat

M&L for coloured glazed ceramic tiles 300 x 450 x 7-8mm thick in vertical surface, set and jointed in neat cement slurry & pointed with white or coloured cement to match

M & L for 15mm thick Screed bed or bedding layer in cement mortar 1:6 for laying floors finishes

M&L non-skid coloured ceramic tiles 7 to 8mm thick square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile all as specified and directed by Engr-in-charge

S&F in repairs bib taps standared of PTMT 15mm bore dia any colour high presure screwed for iron pipe of Make Prayag fixed (minimum weight 90 gms) complete all as specified and directed

S&F in repairs PVC valveless,symphonic action type,flushing cistern ,low level white,with inlet,ball valve,float and handle including brackets of 10 ltrs inclluding flush pipe of polyethelene of low or high dencity or PVC, 32 mm dia all as specified and direcetd.

S & F PVC connections 15mm size with PTMT nuts of length 450mm.

S &F in repairs Vitreous china bowl urinal flat back ,size of 465x355x265 white (minimum),with grating and union for discharge pipe (excluding flushing cistern,flush pipe and waste pipe)

S&F 40mm size waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F waste coupling of PTMT (half or full threaded), 32 mm bore dia (Min weight 45 gms) (half or full threaded) suitable for urinals

S&F in repair stop valve, 15mm bore dia PTMT of any colour high pressure screwed for iron pipe and fixed (Minimum weight 90 gms) complete all as specified and directed

S&F in repair Pillar tap, 15mm bore dia PTMT of any colour high pressure screwed for iron pipe and fixed (Minimum weight 110 gms) complete all as specified and directed

S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)complete all as specified and directed

S&F in repair swivel shower of PTMT any colour for fixing with 15mm pipe complete all as specified and directed

S & F in repairs Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) complete all as specified and directed

S & F in repairs 75mm PVC (SWR) floor trap, plainwith grating including jointing with solvent cement complete all as specified and directed

S & F in repairs soap dish any type ,fixed to plugs with choromium plated brass screws complete all as specified and directed

Taking up or down tubes galvanized iron and connections and fittings or removal from site as incl cleaning for refixing where directed complete all as specified and directed.

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 32 mm dia

Re-fixing only tubes galvanized iron and connections fixed to walls or laid in floor supplying & fixing new fittings such as socket, bends, elbows nipple, union etc all as specified and directed of size complete all as specified and directed

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

S/F for tubes medium grade, galvanized with iron all fittings fixed to walls, ceiling and laid in floor of sizes complete all as specified and directed :-

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 32 mm dia

S&F PVC(SWR) pipes 75mm dia single socketed,in any length with rubber ring joints fixed to walls

S&F PVC(SWR) pipes 110 mm dia single socketed,in any length with rubber ring joints fixed to walls

S&F PVC(SWR) 75 mm dia bends of any radius

S&F of PVC(SWR) 110 mm dia bends of any radius

S&F PVC(SWR) 75 mm dia branch piece,single(single Y) equal or unequal

S&F PVC(SWR) 110 mm dia branch piece,single(single Y) equal or unequal

S&F PVC(SWR) junction single,(single T), 75 mm dia equal or unequal

S&F PVC(SWR) junction single,(single T), 110 mm dia equal or unequal

S&F of PVC(SWR) Vent cowl 110 mm dia

S&F 50mm dia low density polyethylene pipes(LDPE) of pressure rating 6 Kgf/cm2 fixed complete to walls as directed by Engr-In-Charge

Taking down carefully existing bitumen tarfelt incl. Screed and cleaning of surfaces of roof etc. With wire brush incl. Flashing and junctions of parapets/kerb walls etc. And removing of the rubbish to a distance exc. 500 metres but not exc. 1.5 km and deposting where directed.

M&L Plastering 10mm thick in cement mortar (1:4) on concrete surfaces mixed with water proofing liquid and smooth finished and smooth(without using extra cement).

Waterproofing on roof including flashing and junction of parapet, kerb, wall etc. As under (a) A coat of hot blown type bitumen of grade 85/25, applied hot @ 0.70 kg/sqm (b) Laying by thermo fusion ( torch applied) 3 mm thick APP based polymeric water proofing membrane weighing not less than 3.5kg/sqm and reinforcement with polyester non woven fabric ( not less than 150 gms/sqm) (c ) Painting the exposed APP membrane surface with bituminous paint @ 0.15kg/sqm

Taking down of shutters of any description exc 1.00 sqm and n exc 2 sqm each shutter complete all as specified and directed

Taking down chowkat or frames with shutters (without taking off shutters from the frame not exc. 1.5 Sqm each.

Taking down chowkat or frames with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4 sqm each.

Taking down of shutters of any description n. exc 1.00 sqm shutter complete all as specified and directed

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube S&F in opening as per specification and drawing.

S&F factory made soild panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing.

S&F II nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, sup-plied and fixed

M & L for 2nd class Hard wood Pain fillets, square, rectangular or triangulars in section,bull nosed, splayed, chamfered or rounded on one edge or face, section area exc 13 & n.exc 25 sq.cm, rought, fixed with screws

S&F IInd class hard wood factory made Glazed and ske- leton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (divided in to square with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mi-tred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Sec-tion 8, cla-use 8.20 (a); supplied and fitted to chowkats.

S&F IInd class HW 35mm thick plain framed factory made panelled shutters (two panel) with lock rail, panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Part I) Kiln, Seasoned and chemically pressure treated.

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., for windows and ventilators, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (b)

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L for preparation of old wooden surface of any description over 10cm width or girth and applying one coats of synthetic enamel paint.

S&F aluminium alloy anodised sliding door bolt 300mm long with hasp & staple (bolt type) and fixing chops of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast alluminium alloy abd fixed

S&F Aluminium alloy anodised barrel tower bolts 200mm long

S&F MS butt hinges 100mm size medium weight complete all as specified and directed

S&F SS butt hinges 100mm size medium weight complete all as specified and directed

S&F aluminium alloy barrel tower bolt 150 mm long

S&F 150 mm extruded aluminium alloy handels

S & F 50 mm long medium weight, cold rolled mild steel Butt hinges.

S&F 75 mm extruded aluminium alloy handels

S & F Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples.

S&F in repairs 1st class hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each

Dismantling water tanks of size exc 500Ltrs but n. exc 1000Ltr and removing to store

S&F Rotational moulded polyethylene water storage tanks double layered 1000 ltr capacity(cylindrical verticalwith closed top) hoisted and fixed in position all as specified in SSR Part I

S&F 25mm bore dia Nipple suitable for HDPE water tank. (Minimum weight 25mm- 65gms)

S&F 25mm bore dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

Supply only Sheet glass ordinary quality 3.00 mm thick n. exc 0.5 sqm each pane complete all as specifed and directed

Dismantling of stone slabs & tiles of any description or thickness (except ceramic tiles) in floors, aprons etc laid bedded & pointed in any mortar complete all as specified and directed

M&L 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

Moulding to granite (single or double) slab including rounding off edges for 18 to 20 mm thick slabs including grinding and polishing

Demolition of cement concrete concrete(un reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M/L for 75mm thick PCC 1:3:6 type C1 ( using 20mm graded stone aggregates) as in plinth protection finished even and fair without using extra cement all as specified.

M&L 75 mm thick PCC 1:4:8,type D-2(using 40mm graded stone aggregate)as in sub base to flooring finished even and fair without using of extra cement all as directed by EIC.

S&F in repairs Vitreous china wash basin, white , flat back , size 550 x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets fixed in repairs.

S&F Providing precast cement concrete type B1, 1:2:4 (20mm graded stone aggregate) in window or door cills, lintels, bressumers, steps,quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, Kerb stones etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match with CM 1:4 complete all as specified and directed.

M&L for preparation of old painted surfaces of plaster, stone , brick concrete of any description over 10cm girth or width, not otherwise described and applying one coat of synthetic enamel paint (Ordinary tint) complete all as specified and directed.

S&F in repairs tubular rail curtain rod/towel rail, 20mm dia, brass chromium plated complete all as specified and directed by EIC.

S&F in repairs for brass chromium plated brackets for 20mm dia tubular curtain rod/towel rail complete all as specified and directed by EIC.

S&F in repairs Gun metal,globe or gate valves,with iron wheel head,screwed both ends for 32mm bore iron pipe and fixed.

S & F machine cut cudappa stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete Note: screed bed layer measured seperately complete all as specifed and directed.

M&L for rubber moulded machine pressed precast inter locking paver block with gray cement any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-25 grade laid on 30mm thick stone dust cushioning laid dry to the profile complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

Taking down and hanging during point wiring of ceiling fan/exhaust fan of any size and sweep in proper manner and connecting up including provision of cable from ceiling rose or connector to fan all as per specified and directed by Engr-in-Charge

Dismantling unserviceable main switch/DBs with MCBs and wooden board including making good disturbed surface of wall.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surfaces.

Point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade surface casing capping not less then 20 mm width with MS sheet metal sunken switch/Terminal box 1.2 mm thick and ebonite switch board cover 3.0 mm thick or PVC moulded switch board and brass screws with cup washers including all necessary wall cutting and making good disturbed surface all as directed and specified. Note : Cutting chases and making good to match with the adjoining surface shall be included in the unit rate.

(a) One light point controlled by one, one way switch

(b) One ceiling /exhaust fan point controlled by one switch and regulator

(c) One 3 pin 5 amp socket out point on the same board with other switches.

(d) One3 pin 5 amps socket out let point on independent board

S &F Switch piano flush type single pole one way 5 amps.

S &F Socket outlet 2 in 1, 3 pin, 6A

S &F Switch socket combination 2 in 1, 6A flush type

S &F Ceiling rose, 3 phase/PVC/polycarbonate, isolated body

S &F Electronic regulator 100/120 Watt step type

S &F Lamp holder insulated body with back plate for angle holder including 9W LED Lamp all as per specified.

Supply and fixing LED lights fitting 1x 20W, 220V, AC, decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver (Make : Havells/Crompton/Bajaj )

S & F 15 Watt LED street light fitting luminaire made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 , including coneecting up with 2/3 core flexible coppper conductor cable , compete all as specified and directed by Engr-in-Charge.

Fabrication,supply & fixing of GI pipe bracket up to 40 mm dia- 0.9m long & 2 set of clamps made out of 30x5mm ms flat & fixed with anchor bolt suitable for 15 w LED security light fitting

Material and labour for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 4 Sqmm, earth continuity conductor of size 4 Sqmm to be drawn through and including PVC casing capping not less then 32mm dia medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge. Notes:- Two wires of 4 sqmm and one wire of 4 sqmm for earthing and one run of PVC casing capping shall be measured as one unit.

Material and labour for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through and including PVC CASING CAPPING not less then 32mm dia medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge. Notes:- Two wires of 6 sqmm and one wire of 6 sqmm and one run of PVC casing capping shall be measured as one unit.

S & F 4 way TP&N Vertical Loadline DBs in double door suitable for TP/FP MCCB with Range upto 160 A , breaking capacity : 10 kA / 16 kA / 25 kA , Bus Bars, Neutral Links, Blanking Plates without out MCCB, HSN Code - 8537, complete all as specified and directed by Engr-in-Charge,

S&F Sheet metal enclosure factory made for DBs Triple pole and neutral double door 415 volts 4 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed.

S&F Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 8 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed.

S&F Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 4 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed.

Supply and fix for MCB TPN 415 Volts, 'C' series, breaking capacity 10 KA of rating 63Amps

S&F MCB, single pole and neutral, 240 Volts , 40-63 Amps all as specified and as directed.

S&F MCB, single pole and neutral, 240 Volts , 6-40 Amps all as specified and as directed.

S&F MCB singal pole 240 Volts , 32 to 63 Amps all as specified and as directed.

S&F MCB singal pole 240 Volts , 6 to 32 Amps all as specified and as directed.

S & F in repair MCCB, 100 Amps , 415Volts, 16KA ,4 pole.

M&L Earthing complete with galvanized steel earth plate electrode 600mm x600 mm x 6mm buried directly in ground vertically to a depth not less then 2.25 meter below normal ground level with top edge of the plate not less then 1.50 meter below normal ground level connected to galvanized earth wire 4.00mm dia by means of bolts ,nuts ,check nuts and washers including earthing pit , charcoal, common salt ,earthing lead 4.00mm dia up to 7.5m, 20mm dia medium grade GI watering pipe ,G.I. protection pipe 15 mm dia up to 7.5m long, PPC pit in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate ,PCC pit cover including earth work of any type of soil/strata all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

Alpha Construction

M/S SAMEER SUBHASH PATANI

M/S MANISH CONSTRUCTION CO

Samruddhi Construction