SBM 2.0 SWM Wet Waste

Amount

Earthwork open excavation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting but inclusive of shoring, strutting and baling out water wherever necessary and depositing the excavated earth within the compound in places shown by departmental officers with an initial lead of 10m and lift of 2m and clearing and leveling etc. complete complying with standard specification.

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted - etc., complete complying with standard specification.

Cement concrete 1:4:8 mix (One cement four sand and eight aggregate) using 40 mm ISS metal including mixing, laying, consolidating curring cost and conveyance of all materials to site and all labour charges etc., complete as per standard speicification

Supplying and erecting centering to sides and soffits including supports and strutting with necessary cross bracing for plain surface such as RCC slabs rectangular beams all beams lintels etc. Centering for soffits of RCC slabs plain surface including strutting upto 3.29 meter height using mild steel of size 90 cm x 60 cm x 10 gauge with MS angles of size 25 mm x 2 mm x 3 mm laid over silver oak (CW) joists of size 10 cm x 6 cm spaced upto 90 cm c/c and supported casurina props or 10 cm to 13 cm dia spaced at 0.750 cm c/c complying with standard specification and as directed by the departmental officer a) Without Strutting

b) Above basement

c) Toilet Roof plain surface

Providing and laying in Position, Standardised concrete mix M-20 Grade in accordance with IS :456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement concrete of 325 Kg/M3 and maximum water content ratio of 0.55, including admixture (Plasticiser / Super Plasticiser) in recommended Proportions as per IS :9103 to accelerate. retard setting of concrete, improve workability without preparing strength and durability with about (5 cu.m) 7730 Kg of 20mm machine crushed stone jelly and with about (3.30 cu.m) 5156 Kg of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 Kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also laying, vibrating with mechanical vibrators, finishing curing etc., and providing fixtures like fan clamps in the RCC floor/roof slabs wherever necessary without claming etc., complete complying with standard specifications and as directed by the departmental officers. The coarse and fine aggregates to be used should be comply with the requiremnts of IS standard.(No seperate payment will be made by the department for the excess uasge of materials)- upto Basement. a) Upto Basement

b) Above basement

Supplying and fabrication placing in position of M.S. (or) RTS rods for required size and length as directed by the deparmental officers approved design including bending cutting tying and cost of binding wire cost and conveyance of all materials to site etc., complete as per standard specification

Plain Cement concrete1:2:4 Mix Using 20mm metal including cost of mixing laying curing etc complete complying with standard specification

Brick work in cement mortar 1:5 mix using (One cement and five sand) using best quality of Fly Ash bricks of size (9"x4 3/8"x2 3/4") for foundation including curing cost and conveyance of all materials to site and all labour charges etc., complete as eper standard specification a) Upto Basement

b) Above basement

Plastering with cement mortar 1:5 mix (One cement and five sand ) to 12 mm thick including curing cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification

Supply and fixing of M.S. iron grill gate of required size and design approved by the departmental officers including cost of materials and labour charges including one coat of primer of red oxide etc., complete as per standard specification

Supplying and fixing of RCC jolly work 50 mm thick with cement concrete 1:2:4 using HBG jelly following thick including moulding finishing and curing etc., complete

Plastering with cement mortar 1:3 mix (One cement and three sand ) to 10 mm thick mixing curring cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification

Supplying and fixing steel door double lead made out of 18 gauge M.S. sheet outer frame of 40 mm x 40 mm x 6 mm 'L' angle linner frame of 30 mm x 30 mm x 5 mm 'L' angle cross stiffener M.S. flat 25 mm x 6 mm with aldrop 1 No, tower bolts 4 Nos. two handlde and six hold fast complete welded and revitted and painted one coat of red oxide paint including cost and conveyance of all materials and labour etc., complete

Painting two coats with approved quality of (soncem) cement paint over the plastered surface including curing cost and conveyance of all materials to site and all labour charged etc., complete as per standard specification

Supplying and fabrication and fixing in position of anodised natural colour matt fininsh sliding Door in TWO track in all floors with following sizes. All the two shutters with slinging entering and made with UPVC (ultra Polyvinyl Chloride ) section for outer frames as shown below with necessary accessories such rubber beading.clips, handle and fixing 5 mm thick clear sheet glass including all required for fabrication etc., complete. Necessary dismantling making holes in RCC columns, beams, mansory wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers. (All materials should be got approved by the Executive Engineer before fixing in position)

Painting two coats with best approved quality of enamel paint over one coat of priming for new iron work including all labour charges etc., complete as per standard specification

Supply and fixing of trusses using necessary 'L' angels and I section each according to design approved by the departmetal officers including cutting, welding cost and conveyance of all materials to site and all labor charges etc., complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete. 20MM dia,G.I pipe

25MM dia,G.I pipe

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements. 20mm dia G.M.Gate Valve

25mm dia G.M.Gate Valve

Brick partition wall 11.50 cm thick in cement mortar 1:3 mix (One cement and three sand) mix using (9"x4 3/8"x2 3/4") cm best Fly ash bricks including cost and conveyance of all materials and labour cost and etc., complete as per standard specification .

Plastering with cement mortar 1:3 mix (One cement and three sand ) to 20 mm thick mixing curring cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification

Supplying and fabrication and fixing in position of anodised natural colour matt finish sliding window in two track in all floors with following sizes. All the three shutters with slinding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section for outer frames as shown below with necessary accessories such rubber beading. Aluminium clips, rubber beading,handle and fixing 4mm thick clear sheet glass including all required for fabrication etc., complete.Necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers.The Al.Surfaces is to be anodised with matt finish under electrically condition in accordance with ISI 1868/1962 specification for an average anodic film thick of not less than 15 microns. (All materials should be got approved by the Executive Engineer before fixing in position)

Paving the floor with palin/design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement

Dadooing walls with glazed tiles (colour) of size 305 x 200 x 6 mm laid in cement mortar 1:2 mix to 10 mm thick and painting with white cement using 0.40 kg / 1 M 2 including finishing the jointing and painting with tiles surface including and labour charges cost and conveyance of all materials to site etc., complete as per standard specification

Supplying and fixing in position best quality approved make colour glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position of Indian make colour water closet of size in 58 cm x 44 cm (21") orissa pan type with 'P' of 'S' trap and with sand cushion and etc., complete with necessary connection including all labour charges cost and conveyance of all materials to site etc., complete as per standards specification

Supply and delivery and fixing of 2000 litres HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x l00 x 113 mm TW switch box for 5 A 3 pin non inter locking CS plug with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point. (SD - 36)

Wiring with 2x4 sqmm(56/0.3) PVC insulated SC unsheathed Cu.Conductor cable of 1100V grade in suitable pipe on wall and ceiling with PVC accessories with 150 mm x 100 mm x 63mm TW switch box for 15 A 3 pin non inter locking CS plug with painting of suitable colour, with continuous earth wire connection of 14 SWG TC wire for open PVC power plug point. (SD - 39)

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC.unsheathed Cu. Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A F.T. switch with painting of suitable Colourfor open PVC light point / fan point (For electronic regulator) (6points per coil) (SD - 20)

Supply and run of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour (SD - 56)

Supply and run of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour (SD - 67)

Supply and run of 4 of 4 sq.mm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 25mm dia GI pipe (Class 'B') bent at both ends with necessary angle iron up right and end supports for mains (SD - 72)

Supply and fixing of single box type 4'36 W flu fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. (SD - 87)

Supply and fixing of TNEB meter Board suitable for 32A Three Phase service connection with 3 Nos. 32A Fuse unit (500V) 32A neutral link and earth link (1" x 1/8" Copper flat) on TW plank of size 600mm x 450mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit. (SD - 127)

Supply and fixing of 3 Phase 32A aerial fuse unit for 3 Nos 32A fuse units (500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work the tapping pole with necessary clamps. (SD - 132)

Supply and fixing of 32 Amps DP Switch of 500V with metal clad with fuse and neutral (Side Handle) on suitable TW Board with PWD Earthing (SD - 143)