PROVN OF SECURITY COMPOUND WALL OF ICE PLANT, BOUNDARY WALL AT SOUTH EAST PORTION OF BUTCHERY MD ACCN AND ADDN/ALTN OF BOUNDARY WALL BETWEEN OFFR MD ACCN AT KR ENCLAVE AND CIVIL AREA AT DANAPUR UNDER GE DANAPUR CANTT

Amount

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

Removing mortar from and cleaning bricks, stacking for measurement including all extra handling and removal and disposing off rubbish complete

Boring holes 3m deep and 300 mm dia of pile in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50 m complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

M & L for plain cement concrete, 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 design mix using 20 mm graded stone aggregate in foundation, footing, foundation beams, plinth beams, plinth beams, bases for columns, pedestal, under reamed piles, mass concrete, etc complete.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggregate as in columns, pillars, posts, struts etc complete.

M&L plain cement concrete M-25 design mix (using 20 mm graded stone aggregate) as in coping, beams, cantilever, band, bressummers, lintels over 1.5 m clear span etc complete all as specified & directed.

Use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

Use & waste of Form wk to rough finsished square, rectangular or polygonal concrete surfaces as in sides of columns, pillars, posts, struts etc complete

Use & waste of Form wk to rough finished flat surfaces as in sides and soffits of coping etc complete

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per item No 14 except bricks complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed.

All as per item No 16 but other than fair faces complete all as specified and directed.

M & L preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint over and including one coat of primer complete all as specified and directed.

M & L for preparation of new wall surfaces and applying two coats of weather coat paint (Apex) over a coat of primer complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance exc. 50 m but not exc. 250m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

S & F for mild steel angle iron size 50mmx50mmx6mm / any size angle iron / flat iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc and similar work conforing to FE 410--0 or 310--0 complete all as specified and directed.

S & F for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting and also fastening confirming to Fe – 410 – W(Gde E - 250) quality 'B' complete all as specified and directed.

S & F for galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, straining bolts at ends, staples or steel pins etc. ( Each line wire to be measured) complete all as specified and directed.

M & L for two coat synthetic enamel paint over a coat of red oxide on steel surfaces of any description over 10 cm in width of grith not otherwise described including preparation of surfaces complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

Taking down cement plaster on wall / ceiling / roof etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L for Granite work (of any type) 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Earth work in excavation of any type soil by mechanical means (Hydraulic excavator) means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-Charge

M/S PRAVIN ENTERPRISES

M/s Mukesh and company

M/S Priya Trading Agency

M/S SAROJ KUMAR SINGH

MS CHAKRAVARTY PRITHIVI RAJ

M/S ANAND MOHAN ENTERPRISES

MS BIJAY KUMAR AND SONS

M/S MODERN CONSTRUCTION

M/S ARVIND GROUP OF CONSTRUCTION & INFRASTRUCTURE