Infrastructure development of newly created Paye Circle Head Quarter,Kra Daadi District.

Amount

Approach Road(1.50Km)

Formation cutting(FC-1.50 Km)

Excavation in Soil with Dozer with lead upto 100 metres (Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.

Excavation in Ordinary Rock with Dozer with lead upto 100 metres (Excavation for roadway in ordinary rock by deploying a dozer, 80 HP including cutting and pushing the cut earth to site of embankment upto a distance of 100 metres ( average lead 50 metres ), trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.)

Granular Sub-base (150 mm thick) for 1.50 Km

Preparation of Sub-grade

Preparation of sub grade (Preparation of sub grade by excavating earth to an average depth of 22.50 cm, dressing to camber and consolidating with road roller, making good the undulations etc. and disposal of surplus earth, lead upto 50 m.)

Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade.

Granuar Sub-Base with Close Graded Materials (Table: 401)

Plant Mix Method (Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401)

By Manual Means

Cross Drainage :

RCC Slab Culvert 1.00 mtr Span

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.

Manual Means

Depth upto 3 m

Providing and laying boulders Solling for bed for protection against scour with stone boulders weighing not less than 05kg each complete as per drawing and Technical specification.

Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.

Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications.

RCC Grade M30

Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications.

RCC Grade M20

Furnishing and Placing Reinforced/ Prestressed cement concrete in super-structure as per drawing and Technical Specification

RCC Grade M20 , Using Concrete Mixer, Height upto 5m

Construction of precast RCC railing of M25 Grade, aggregate size not exceeding 12 mm, true to line and grade, tolurence of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequate space between vertical post for expansion, complete as per approved drawings and technical specifications.

Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specification.

Providing and laying of boulder apron for bed protection in U/S and D/S protection work complete as per drawing and Technical specifications clause 1300.

Providing & fixing in position HYSD (TMT) reinforcement bars in foundations complete as per drawings and Technical Specifications Section 1000.

Providing & fixing in position HYSD (TMT) reinforcement bars in superstrucutre complete as per drawings and Technical Specifications Section 1000.

Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications

Katcha Side Drain (Surface Drains)

Surface Drain

Surface Drains in Soil (Construction of unlined surface drains of average cross sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions to the requirement of clause 301 and 309. Excavated material to be used in embankment within a lead of50 metres (average lead 25 metres)

Mechanical means

Surface Drains in Ordinary Rock (Construction of unlined surface drain of average cross sectional area 0.4 sqm in ordinary rock to specified lines, grades, levels and dimensions as per approved design and to the requirement of clause 301 to 309. Excavated material to be used in embankment at site.)

Mechanical means

General Ground

SH : Formation cutting(FC)

Excavation in Soil with Dozer with lead upto 100 metres (Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.

Excavation in Ordinary Rock with Dozer with lead upto 100 metres (Excavation for roadway in ordinary rock by deploying a dozer, 80 HP including cutting and pushing the cut earth to site of embankment upto a distance of 100 metres ( average lead 50 metres ), trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.)

Non Residential Building

Circle Office Building

Earth work

Surface dressing of the ground, including removing vegetation and inequalities not exceeding 15 cm depth and disposal of rubbish, lead upto 50 m and lift upto 1.50 m. a)-Hard Soil.

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Dry stone pitching 22.50 cm thick including supply of stone and preparing surface complete (including carriage of stone for 5 km lead).

C. C. work

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : Foundations and plinth.

R. C. C. work

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : . M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. .M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement withM20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers bands and facias up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding the 6 mm to give a smooth and even surface but excluding the cost of centering, shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 fine sand : 4 stone aggregate 12.5 mm nominal size).

Reinforcement of R C C work including bending, binding and placing in position complete, b) Tar/ TMT steel

Centring and shuttering including strutting, propping etc and removal of form work for :

Foundation, footings, bases of columns etc. and mass concrete.

Column, pillars, posts and struts etc.

Lintels, beams, girders, bressumers and cantilevers etc.

Suspended floors, roofs, landings shelves and their supports, balconies and chajjas ( 3.5 m height).

Stairs (excluding landings) except spiral stair cases.

Vertical and horizontal fins individually or forming box louvers bands and facias.

Brick work

Brick work with best available local bricks in foundations and plinth in cement mortar 1:5 (1 cement : 5 fine sand).

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1cement : 4 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Wood work

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing and fixing flush door shutters, decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

40 mm thick including anodised aluminium butt hinges with necessary screws.

Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticalssides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineerin- charge.

Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm (± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (+ 0.2 mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing 12 mm thick and 150 mm wide pelmet of flat pressed 3 layer particle board (medium density) with 25 mm dia second class teak wood curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.

Timber class - A IV.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

Ornamental grill

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size).

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Steel work

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm x 10 mm x 2 mm and braced with flat iron diagonals 20 mm x 5 mm size with top and bottom rails of T iron 40 mm x 40 mm x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

Flooring work

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to bespecified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12mm thick bed of cement mortar1:3 (1cement:3coarsesand), including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :

Makrana white second quality.

Extra for pre finished nosing to treads of steps of marble stone.

Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, including rounding of junctions with floor.

21 mm thick.

Roofing work

Providing Alumunium Troughed Sheet Roofing fixed with 'J' hooks,bolts, nuts, washer with bitumen (the 'J' hook,nut and bolt are as per IS:733 of 1983) and limpet washer filled with white lead complete excluding the cost of the purlins,rafters and trusses. a)- Using 0.65 mm thick Alumunium Troughed Sheet.

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses. Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages = 12.566m After laping as per manufacturer's specification, effective Measurable length will be (4 x 3.05) - (3 x 0.15) = 11.75m.

Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately).

Providing and fixing on wall face C.I. rain water pipe including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement : 2 fine sand).

100 mm diameter pipe

Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1 : 2 : 4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc.

100 mm diameter pipe

Finishing work

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand) .

15 mm cement plaster 1 : 5 (1 cement : 5 fine sand) on the rough side of single or half brick wall.

6 mm cement plaster to ceiling 1 : 3 (1 cement : 3 fine sand).

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Wall painting (two or coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Miscelleaous Work

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Brick edging 7.50 cm wide and 12.50 cm deep to plinth protection with 2nd class bricks including grouting with cement mortar 1 : 4 (1 cement : 4 fine sand).

Drainage Work

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

100 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design.

100 mm dia SW pipes

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honey comb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

Water Supply Work

Providing and fixing GI/CPVC pipes complete with GI/CPVC fittings and clamps including cutting and making good the walls (internal work).

15 mm nominal bore

20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

25 mm nominal bore

32 mm nominal bore

Providing and fixing brass bib cock of approved quality.

15 mm nominal bore

Providing and fixing brass stop cock of approved quality.

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing PVC connection pipe with brass union.

45 cm length 15 mm nominal bore.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing brass full way valve with wheel of approved quality.

32 mm nominal bore.

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet.

150 mm dia

Samitary Installation Work

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

Orissa Pattern WC Pan.

Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Litres high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required.

WC pan with white plastic seat and lid.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality).

750 x 20 mm size

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.

100 mm inlet and 100 mm outlet

100 mm inlet and 75 mm outlet

Providing and fixing CP brass waste for wash basins and sinks.

40 mm dia

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

100 mm dia SW pipes

75 mm dia SW pipes

Providing and fixing 100 mm sand cast iron grating for gulley, floors or nahni trap .

Providing and fixing sand cast iron/ cast iron (spun) soil, plain bands.

100 mm diameter pipe

75 mm diameter pipe

Painting two or more coats on rain water, soil waste and vent pipes and fittings with black anti-corrosive bituminoustic paint of approve brand and manufacture over a priming coat of ready mixed genuine red lead on new work.

100 mm dia

ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) : For fixed portion. Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron).

For shutters of doors, windows & ventilators including providing and fixing hinges /pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron).

Providing and fixing glazing in aluminium door, window, ventilator shutters andpartitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) :

With float glass panes of 4.0 mm thickness.

With float glass panes of 8.0 mm thickness.

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete.

Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. Complete as per direction of Engineer-in-charge

Polyester powder coated minimum thickness 50 micron aluminium .

Residential Building

Type-II Quarter (Single unit)

Site Development

Clearing and Grubbing Road Land, (Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness.)

By Manual Means:- In area of light jungle.

By Mechanical Means :- In area of thorny jungle

Excavation in Soil with Dozer with lead upto 100 metres (Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.)

Excavation in Ordinary Rock with Dozer with lead upto 100 metres (Excavation for roadway in ordinary rock by deploying a dozer, 80 HP including cutting and pushing the cut earth to site of embankment upto a distance of 100 metres ( average lead 50 metres ), trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.)

Earth work

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Dry stone pitching 22.50 cm thick including supply of stone and preparing surface complete (including carriage of stone for 5 km lead).

C. C. work

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : Foundations and plinth.

Providing and laying damp proof course 38 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 12.5 mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by manufacturers.

R. C. C. work

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : . M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. .M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement withM20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement of R C C work including bending, binding and placing in position complete, b) Tar/ TMT steel

Centring and shuttering including strutting, propping etc and removal of form work for :

Foundation, footings, bases of columns etc. and mass concrete.

Column, pillars, posts and struts etc.

Lintels, beams, girders, bressumers and cantilevers etc.

Suspended floors, roofs, landings shelves and their supports, balconies and chajjas ( 3.5 m height).

Vertical and horizontal fins individually or forming box louvers bands and facias.

Brick work

Brick work with best available local bricks in foundations and plinth in cement mortar 1:5 (1 cement : 5 fine sand).

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1cement : 4 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Wood work

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position

Providing and fixing flush door shutters, decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

40 mm thick including anodised aluminium butt hinges with necessary screws.

Providing and fixing 38 mm thick wire gauge shutters using galvanized mild steel wire gauge of IS gauge designation 140G with wire of dia 0.56 mm for doors, windows and clerestory windows including anodized aluminum butt hinges with necessary screws.

Best available local wood class B-I.

Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticalssides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineerin- charge.

Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm (± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (+ 0.2 mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing 12 mm thick and 150 mm wide pelmet of flat pressed 3 layer particle board (medium density) with 25 mm dia second class teak wood curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.

Timber class - A IV.

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing oxidised M.S. Safety chain with necessary fixtures for doors, (weighting not less than 450 gms).

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Steel work

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

Flooring work

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to bespecified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12mm thick bed of cement mortar1:3 (1cement:3coarsesand), including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick.

Extra for pre finished nosing to treads of steps of marble stone.

Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, including rounding of junctions with floor.

21 mm thick.

Roofing work

Providing Alumunium Troughed Sheet Roofing fixed with 'J' hooks,bolts,nuts, washer with bitumen (the 'J' hook,nut and bolt are as per IS:733 of 1983) and limpet washer filled with white lead complete excluding the cost of the purlins,rafters and trusses.

Using 0.65 mm thick Alumunium Troughed Sheet

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.

Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages = 12.566m After laping as per manufacturer's specification, effective Measurable length will be (4 x 3.05) - (3 x 0.15) = 11.75m

Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately).

Finishing work

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand) .

15 mm cement plaster 1 : 5 (1 cement : 5 fine sand) on the rough side of single or half brick wall.

6 mm cement plaster to ceiling 1 : 3 (1 cement : 3 fine sand).

Providing and applying plaster of paris putty of 2 mm thickness over plasteredsurface to prepare the surface even and smooth complete.

Wall painting (two or coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Miscelleaous Work

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Brick edging 7.50 cm wide and 12.50 cm deep to plinth protection with 2nd class bricks including grouting with cement mortar 1 : 4 (1 cement : 4 fine sand).

Drainage Work

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

100 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design.

100 mm dia SW pipes

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honey comb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

Water Supply Work

Providing and fixing GI/CPVC pipes complete with GI/CPVC fittings and clamps including cutting and making good the walls (internal work).

15 mm nominal bore

20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

25 mm nominal bore

Providing and fixing brass bib cock of approved quality.

15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore

Providing and fixing brass full way valve with wheel of approved quality.

25 mm nominal bore

Providing and fixing PVC connection pipe with brass union.

45 cm length 15 mm nominal bore.

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet.

150 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Sanitary Installation Work

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

Orissa Pattern WC Pan.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board , 510x1040 mm bowl depth 250 mm.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality).

750 x 20 mm size

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms.

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.

100 mm inlet and 100 mm outlet

100 mm inlet and 75 mm outlet

Providing and fixing CP brass waste for wash basins and sinks.

40 mm dia

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

100 mm dia SW pipes

75 mm dia SW pipes

Providing and fixing 100 mm sand cast iron grating for gulley, floors or nahni trap .

Providing and fixing sand cast iron/ cast iron (spun) soil, plain bands.

100 mm diameter pipe

75 mm diameter pipe

Painting two or more coats on rain water, soil waste and vent pipes and fittings with black anti-corrosive bituminoustic paint of approve brand and manufacture over a priming coat of ready mixed genuine red lead on new work.

100 mm dia

75 mm dia

FURNITUREs

Wooden Cot 3'-3'x6'-6'

wooden meat safe

cane chair

writing table

Water Filter 10 litre capacity

Wooden armed Chair with cane seat

Type-III Quarter (Single unit)

SH:- Site Clearance

Clearing and Grubbing Road Land, (Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness.)

By Manual Means:- In area of light jungle.

By Mechanical Means :- In area of thorny jungle

Excavation in Soil with Dozer with lead upto 100 metres (Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.)

Excavation in Ordinary Rock with Dozer with lead upto 100 metres (Excavation for roadway in ordinary rock by deploying a dozer, 80 HP including cutting and pushing the cut earth to site of embankment upto a distance of 100 metres ( average lead 50 metres ), trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.)

Earth work

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Dry stone pitching 22.50 cm thick including supply of stone and preparing surface complete (including carriage of stone for 5 km lead).

C. C. work

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : Foundations and plinth.

Providing and laying damp proof course 38 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 12.5 mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by manufacturers.

R. C. C. work

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : . M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. .M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement withM20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement of R C C work including bending, binding and placing in position complete, b) Tar/ TMT steel

Centring and shuttering including strutting, propping etc and removal of form work for :

Foundation, footings, bases of columns etc. and mass concrete.

Column, pillars, posts and struts etc.

Lintels, beams, girders, bressumers and cantilevers etc.

Suspended floors, roofs, landings shelves and their supports, balconies and chajjas ( 3.5 m height).

Vertical and horizontal fins individually or forming box louvers bands and facias.

Brick work

Brick work with best available local bricks in foundations and plinth in cement mortar 1:5 (1 cement : 5 fine sand).

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1cement : 4 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Wood work

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws.

38mm thick best available local wood class - B I.

Providing and fixing flush door shutters, decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

40 mm thick including anodised aluminium butt hinges with necessary screws.

Providing and fixing 38 mm thick wire gauge shutters using galvanized mild steel wire gauge of IS gauge designation 140G with wire of dia 0.56 mm for doors, windows and clerestory windows including anodized aluminum butt hinges with necessary screws.

Best available local wood class B-I.

Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticalssides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineerin- charge.

Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm (± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (+ 0.2 mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing 12 mm thick and 150 mm wide pelmet of flat pressed 3 layer particle board (medium density) with 25 mm dia second class teak wood curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.

Timber class - A IV.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

Ornamental grill

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size).

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing MS Hooks and Eyes.

Providing and fixing oxidised M.S. Safety chain with necessary fixtures for doors, (weighting not less than 450 gms).

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Steel work

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

Flooring work

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to bespecified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12mm thick bed of cement mortar1:3 (1cement:3coarsesand), including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick.

Extra for pre finished nosing to treads of steps of marble stone.

Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, including rounding of junctions with floor.

21 mm thick.

Roofing work

Providing Alumunium Troughed Sheet Roofing fixed with 'J' hooks,bolts,nuts, washer with bitumen (the 'J' hook,nut and bolt are as per IS:733 of 1983) and limpet washer filled with white lead complete excluding the cost of the purlins,rafters and trusses.

Using 0.65 mm thick Alumunium Troughed Sheet

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.

Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages = 12.566m After laping as per manufacturer's specification, effective Measurable length will be (4 x 3.05) - (3 x 0.15) = 11.75m

Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately).

Finishing work

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand) .

15 mm cement plaster 1 : 5 (1 cement : 5 fine sand) on the rough side of single or half brick wall.

6 mm cement plaster to ceiling 1 : 3 (1 cement : 3 fine sand).

Providing and applying plaster of paris putty of 2 mm thickness over plasteredsurface to prepare the surface even and smooth complete.

Wall painting (two or coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Miscelleaous Work

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Brick edging 7.50 cm wide and 12.50 cm deep to plinth protection with 2nd class bricks including grouting with cement mortar 1 : 4 (1 cement : 4 fine sand).

Drainage Work

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

100 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design.

100 mm dia SW pipes

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honey comb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

Water Supply Work

Providing and fixing GI/CPVC pipes complete with GI/CPVC fittings and clamps including cutting and making good the walls (internal work).

15 mm nominal bore

20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

25 mm nominal bore

Providing and fixing brass bib cock of approved quality.

15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore

Providing and fixing brass full way valve with wheel of approved quality.

25 mm nominal bore

Providing and fixing PVC connection pipe with brass union.

45 cm length 15 mm nominal bore.

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet.

150 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Samitary Installation Work

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

Orissa Pattern WC Pan.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board , 510x1040 mm bowl depth 250 mm.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms.

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.

100 mm inlet and 100 mm outlet

100 mm inlet and 75 mm outlet

Providing and fixing CP brass waste for wash basins and sinks.

40 mm dia

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

100 mm dia SW pipes

75 mm dia SW pipes

Providing and fixing 100 mm sand cast iron grating for gulley, floors or nahni trap .

Providing and fixing sand cast iron/ cast iron (spun) soil, plain bands.

100 mm diameter pipe

75 mm diameter pipe

Painting two or more coats on rain water, soil waste and vent pipes and fittings with black anti-corrosive bituminoustic paint of approve brand and manufacture over a priming coat of ready mixed genuine red lead on new work.

100 mm dia

75 mm dia

FURNITUREs

Wooden Cot 3'-3'x6'-6'

Meat Safe

Cane Chair

Centre Table

writing table

Dining Chair

Water Filter 10 litre capacity

Wooden armed Chair with cane seat

Dining table(5'x3')

Chain Link Security Fencing

1.20 m high welded steel wire fencing with 1.80 m RCC posts of standard design placed at every 3 m apart embedded in cement concrete blocks 45 x 45 x 60 cm of mix 1 : 5 : 10 (1 cement : 5 fine sand : 10 stone aggt. 40 mm nominal size), corner end and every 10th post to be strutted and embedded in cement concrete blocks of 70 x 45 x 50 cm of same mix provided with welded steel wire fabric 0.90 m wide, rectangular mesh 75 x 25 mm size weighing not less than 7.75 kg per Sq.m. fixed between the two posts fitted and fixed with GI staples on wooden plugs or tied to 6 mm bar nibs with binding wire including earth work in excavation, concrete work and cost of posts, struts etc complete.

Providing and fixing MS Gate (size 1.20 x 1.20 mtr ) .as per specification and direction of Engineer in charges.

Ms Sha Enterprise (BID ID -7607)