GEU(N)40 2022 23PROVISION OF 2 BATH ROOM AND TOILET BLOCK NEAR MAIN GATE AND SINGLE JCO LIVING FOR ENGR REGT INCLUDING PROVISION OF ADDTION ALTERATION TO BLDG NO P11 P12 OF DDGSI ALONG WITH SPECIAL REPAIR TO BLDG NOP16AT KRIMCHI UNDER GE N UDHAMPUR

Amount

M&L for surface excavation n.exc. 30 cm deep and averaging 15 cm deep and getting out in hard dense soil complete all as specified and directed by Engineer in charge.

M&L for excavating in trenches n. exc. 1.5 m wide, and n.exc. 1.5 m in depth for foundation etc. n.exc. 10 Sqm on plan and n. exc. 1.5 mtr in depth and gettingin any type of soil complete all as per specified and directed by the Engr-in-charge.

M&L for excavating over areas, exc 1.5 m deep but not exc 3.0m deep and getting out in any type of soil,complete all as per specified and directed by the Engr-in-charge.

M&L for returning filling in, including, spreading, levelling, watering and well ramming in layers n. exc. 25 cm complete all as per specified and directed by the Engr-in-charge.

M&L for removing excavated material n. exc. 50 mtr and depositing where directed at a level n. exc. 1.5 mtr above the starting point complete all as per specified and directed by the Engr-in-charge.

M & L for loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells using broken bricks complete all as per specified and directed by the Engr-in-charge.

M&L for hard core of gauge broken stone or boulders n.exc.63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as per specified and directed by the Engr-in-charge.

Demolition of brickwork or stone masonary, built in cement mortar or cement lime mortar complete all as per specified and directed by the Engr-in-charge.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 metre mean radius, using old size bricks, built in cement mortar 1:6 , complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 metre mean radius, using old size bricks, built in cement mortar 1:4 , complete all as specified and as directed.

Description all as per item no 10 above but except bricks

M&L for plain cement concrete (1:5:10) type E2 using 40mm graded agg as in sub base as in foundation and in mass concrete complete all as per specified and directed by the Engr-in-charge.

M&L for from work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work n.exc. 200 mm thick curved ( horizontal or sloping ) with fair finished surfaces for flat roof complete all as per specified and directed by the Engr-in-charge.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as per specified and directed by the Engr-in-charge.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizintal or sloping and similar work exc 10cm but n exc 20cm wide complete all as per specified and directed by the Engr-in-charge.

M&L for formwork to soffits of suspended slabs such as roof slabs,floor slabs,landings & similar work,not exc 200mm thick(horizontal or sloping)fair finishes surfaces of cocrete flat complete all as per specified and directed by the Engr-in-charge.

M&L for re-inforced cement concrete M-25 Design mix in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as per specified and directed by the Engr-in-charge.

M&L for re-inforced cement concrete M-25 Design mix in beams, cantilevers, bressummers, lintels over 1.5m span complete all as per specified and directed by the Engr-in-charge.

M&L for re-inforced cement concrete M-25 Design mix in columns piers posts ane strutscomplete all as per specified and directed by the Engr-in-charge.

M&L for re-inforced cement concrete type B1 (1:2:4) using (20mm graded stone aggregate) M-25 Design mix in foundation footings complete all as per specified and directed by the Engr-in-charge.

M&L for re-inforced cement concrete (nominal mix) type B1 (1:2:4) using (20mm graded stone aggregate) in Chajjas complete all as per specified and directed by the Engr-in-charge.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in coping,bed plates benching etc slightly round or chamfered angles and throating,complete all as specified and directed by Engineer in charge.

M&L for precast cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in cover slabs ( for manholes etc). ,baffle wall including as in kerb stone and similar articles with plain faces, set in cement mortar 1:6, complete all as specified and directed by Engr-in-Charge. .

M&L for plain cement concrete (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in drain, filling and mass concrete complete all as per specified and directed by the Engr-in-charge.

M&L for plain cement concrete 1:4:8 using 40mm graded aggregate as in foundation mass concrete complete all as per specified and directed by the Engr-in-charge.

M&L for plain cement concrete 1:2:4 using 40mm graded aggregate as in surface channel and drains complete all as per specified and directed by the Engr-in-charge.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and smooth with using extra cement complete all as per specified and directed by the Engr-in-charge.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, slabs, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to TMT bars complete all as per specified and directed by the Engr-in-charge.

Ditto as per SI no 28 above but 5mm dia and over up to and including 10 mm dia in stirrups, spaces and binders complete all as per specified and directed by the Engr-in-charge.

S & F framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as per specified and directed by the Engr-in-charge.

S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as per specified and directed by the Engr-in-charge.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as per specified and directed by the Engr-in-charge.

Extra for forming fair finished drain or channel upto 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. complete all as per specified and directed by the Engr-in-charge.

Supply only integral water proofing compound complete all as per specified and directed by the Engr-in-charge.

M&L for concrete bed to drain pipes of bore 150mm including packing under,and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate including necessary shuttering and supports, complete all as per specified and directed by the Engr-in-charge. Note:- (i) Thickness of bed belew barrel of pipe -10 cm. (ii) Width of bed :- outer dia of pipe plus 30 cm.

M&L for Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as per specified and directed by the Engr-in-charge.

M&L for providing 75 mm thick cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in floors, sub base complete all as per specified and directed by the Engr-in-charge.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and rough to receive tiles without using extra cementcomplete all as per specified and directed by the Engr-in-charge.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection even and smooth with using extra cement complete all as per specified and directed by the Engr-in-charge.

M&L for dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiles to store and rubbish off the premises,complete all as per specified and directed by the Engr-in-charge.

S&F glazed ceramic tiles (coloured) on vertical surfaces 450x300x6 to 7 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match including 10mm thick screed (1:3) all as specified & directed by Engr-In-Charge.

M&L for non skid coloured glazed ceramic tiles area of each tile exc. 11 Sqm but n.exc. 18 Sqm 7mm to 8mm mm thick as in floor finishes set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick screed bed of cement mortar(1:4) all as specified & directed by Engr-in-Charge.

All as per item no 42 above but as in skirting over vertical surfaces & including 10 mm thick cement mortar 1:3 screed, set and jointed with grey cement slurry and pointed in grout of matching shade of tilescomplete all as per specified and directed by the Engr-in-charge.

M&L for light shade Vitrified ceramic tiles 10mm thick (square/ rectangular) area of each tile not exceeding 0.36Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick cement mortar 1:4 screed, set and jointed with grey cement slurry & pointed with grout of matching shade,complete all as per specified and directed by the Engr-in-charge.

All as per item no 44 above but as in skirting over vertical surfaces & including 10mm thick cement mortar 1: 3 screed, set and jointed with grey cement slurry and pointed in grout of matching shade of tilescomplete all as per specified and directed by the Engr-in-charge.

M&L for machine cut kota stone slab flooring 20-25 mm thk over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including laying over 20mm thick Screed in cement mortar 1:4 complete all as specified and directed.

M&L for kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar jointed with ditto as per item above & including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for granite (of any type) 18 mm to 20 mm thk work (table rubbed & polished) as in steps, jambs, pillars, window cills, cooking platforms and like ,machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone laid over & incl 20 mm thk screed bed in CM 1:4complete all as specified and directed by Engineer in charge.

M & L for 18mm thick marble strip cut to width not exceeding 100 mm wide fixed as border in stair case walk ways etc., complete incl 15 mm thick screed in CM 1:6 complete all as specified and directed

M&L for treatment of sunken floor surfaces with 0.488 kg/Sqm first layer of slurry of cement mixed with acrylic based polymer modified cementitious composite compound @0.253 Kg/Sqm. This layer shall be allowed to be cured for 4 hours and then applying in second layer slurry of cement @ 0.242 Kg /Sqm mixed with acrylic based polymer based modified cementitiousc omposite compound @0.126 Kg/Sqm. This layer shall be allowed to be cured for 4 hours incl fixing of 32 mm dia GI spout pipe 450mm long complete all as specified and directed by Engineer in charge.

M&L for 10mm thick rendering on concrete surfaces to be finished even and smooth ( w/o using extra cement) in cement mortar 1:3 in roof slab complete all as per specified and directed by the Engr-in-charge.

M&L for preparing RCC roof slab top by wire brushing and cleaning the dust and forign materail etc complete and applying a coat of hot blown bitumen 85/25 grade @ 1.20kg/Sqm over a coat of bitumen primer @ 0.40 ltrs/Sqm and there after laying of a layer of APP based polymeric membrane (five layered with centre core as 100 microns high molecular high density polyethylene film) weighing not less than 3.5 kg/Sqm and reinforced with polyster non woven fabric (wt. not less than 150 gms/Sqm) laid on bituminous surface by press application method with 75mm side overlap and 100mm end overlap. The membrane has to be laid with LPG torch application and overlaps sealed and finished neat, after that applying one coat of bitumen 85/25 grade on top surface @ 1.20 kg/Sqm and blinded with premier dry sand @ 0.5 kg/Sqm dusted over bitumen coat, complete all as specified and as directed. Note :- Water proofing treatment will be done by manufacturer of APP membrane or through their authorised specialized agency which will further have to give a five years warranty for rectification of any defect if incurred at a later stage, otherwise no payment shall be made to the contractor if water proofing treatment is executed by engaging local labour.

M&L for cement concrete tiles 25cmx25cmx20mm thick with grey cement and no pigment , machine pressed, set jointed and pointed in neat cement slurry in floors, terece over and including 20mm thick bedding layer in CM 1:4. complete all as specified and directed by Engr-in-charge.

M & L for providing Chequred cement concrete tiles 25cm x 25cm x22 mm thick tiles set , jointed and pointed in neat cement slurry in floors with grey cement ant pigment laid over & incl 20 mm thk screed bed in CM 1:4 all as spd & dir

M & L for machine pressed precast interlocking paver blocks any shape and size with grey cement and pigment confirming to IS-15658-2006 of 60mm thickness (M-35 Grade) including sand cushioning bed (filling under floors) including spreading levelling watering if required complete all as specified and directed.complete all as per specified and directed by the Engr-in-charge.

M&L for apply two coats of aluminium paint on roof complete all as per specified and directed by the Engr-in-charge.

M&L for forming construction joint 30 mm deep x 10 mm wide filled with sealing compound grade 'B' complete all as per specified and directed by the Engr-in-charge.

Dismantling wall and ceiling boards, fibre pulp insulation etc or insulation boards/ sslabs/ blankets, any thickness, including cover fillets,complete all as per specified and directed by the Engr-in-charge.

S&F non asbestos fibre cement board ceiling 4mm, thick in 600x 600mm panel designed ceiling conforming to IS-14862 type B category three including snpgrid frame work, hold fast, suspenders complete all as per specified and directed by the Engr-in-charge.

M&L for solid PVC wall lining consisting of 5mm thick single side prelam PVC sheet instead of plain PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as per specified and directed by the Engr-in-charge.

M&L for taking down cement plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as per specified and directed by the Engr-in-charge.

M&L for rendering 10 mm thick on fair faces of brick work on concrete internal surfacs in CM (1:6) and finished even and smooth ( w/o using extra cement) complete all as per specified and directed by the Engr-in-charge.

M&L for rendering 15 mm thick on fair faces of brick work on concrete surfacs in CM (1:4) on external brick / concrete surface finished even and smooth ( w/o using extra cement) complete all as per specified and directed by the Engr-in-charge.

M&L for rendering 5 mm thick on fair faces of brick work on concrete surfacs in CM (1:3) on ceiling surface finished even and smooth ( w/o using extra cement).complete all as per specified and directed by the Engr-in-charge.

M&L for 10mm thick screed bed or bedding layers in CM 1:4 finished even and rough for laying floor finishes complete all as per specified and directed by the Engr-in-charge.

M&L for providing and applying ready to use single component high strength polymer modified cementious repair mortar 25 mm thick with water/ powder ratio as specifiedby manufacturer so as to achieve the following parameters:- (i) 28 days Compressive Strength>= 50N/mm2 (ii) Flexural Strength at 28 days>= 5 N/mm2 incl removal or chipping of loose concrete, application of rust remover, followed by a coat of corrosion resistance coating,bonding agent & curing compound Make:- Sikatop 122 HS/ Fosroc Nito Mortars/ Equivalent in BASF

M&L for two coat of Apex point over a coat of alkali resistant primer paint including preparation of newly plastered surfaces of wall upto 7m height from ground level and at all locations as directed including scaffolding, cleaning and curing etc. complete as directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper over a coat of primer over 2to 3mm thick wall care putty complete all as per specified and directed by the Engr-in-charge.

M&L for preparation of newly plastered surfaces and applying three coat of white wash on ceiling complete all as per specified and directed by the Engr-in-charge.

M&L taking down chowkat or framed with shutter (without taking off shutter from the frames) not exceeding 1.5Sqm each complete all as per specified and directed by the Engr-in-charge.

M&L taking down chowkat or frame with shutter (without taking off shutter from the frame) exc 1.5Sqm but n.exc 4Sqm each complete all as per specified and directed by the Engr-in-charge.

S&F powder coated anodised aluminium door shutters, aluminium section weighting 0.55 kg/m including necessary joining cleats, glazing clips, rubber neopreans packing, handles 2 Nos I each door, hinges, anodised, aluiminium snap beading screws etccomplete all as per specified and directed by the Engr-in-charge.

S&F powder coated anodised aluminium window and ventilator shutters, side hung tye without sash bars, aluminium sections weighting 0.55kg/m including necessary joining, cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as per specified and directed by the Engr-in-charge.

S&F 5.50mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares exceeding 0.50Sqm in each pane complete all as per specified and directed by the Engr-in-charge.

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as per specified and directed by the Engr-in-charge.

S&F double action floor spring hydraulically regulated made up of minium 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as per specified and directed by the Engr-in-charge.

S&F in repair 18 mm thick prelaminated particle boards, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws as in shelves , cup board shutters etc, complete all as specified and directed.

Extra over rates of MDF board 18/19mm wide for external teak wood lipping, 6mm thick fixed with nails complete all as per specified and directed by the Engr-in-charge.

M&L for pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including S&F necessary fixing lugs, hinges, lock strike plate, hold fast etc. complete, of frame size 105 mm x 60 mm, including one shop coat of red oxide zinc chrome primer,complete all as specified and as directed by Engr-in-Charge.

M&L for pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including S&F necessary fixing lugs, hinges, lock strike plate, hold fast etc. complete, of frame size 125 mm x 60 mm, including one shop coat of red oxide zinc chrome primer ,complete all as specified and as directed by Engr-in-Charge.

M&L for factory Made PVC Moulded Door Shutter of wall nut colour, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core, fix in frame at site as per specification & drawing as per specification & drawing, complete all as specified and as directed by Engr-in-Charge.

M&L factory made 2nd class hard wood 35mm thick flush door shutters solid core with particle board exterior grade as per IS-22002 of 1983 (Part-I). Flush door shutters shall be internally lipped as per clauge 8.21 of SSR-1919 Part-I. Flush shutters solid panels construction with one face covered with decorative face veneer with lipping/ frame to match on both side complete all as specified and directed.

M&L for providing and fixing 30mm thick factory made PVC door shutter consisting of panel of hollow PVC profile of 24mm thickness, consisting of frame made out of M.S tubes of 19 gauge thickness and size of 19mmx19mm inserted inside the hollow section of stiles, top and bottom rails and two 19mmx19mm MS tubes inserted horizontally inside the hollow profile section at an equal distance from top and bottom of door and fixed with hollow profile section using 3mm thick Prelam PVC sheet using screws. Hollow PVC profile shall be lipped with 10mm (5mmx2) thick x 24mm width on stiles and rails using solvent cement. The inner panel shall be laminated with 5mm thick termite proof, water proof and fire retardant Prelam PVC sheet using solvent cement on both the sides of the panel etc complete as per direction of Engineer-in-Charge, manufacturer's specification and drawing.

S&F solid PVC moulded door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings complete all as per specified and directed by the Engr-in-charge.

S&F 2nd hard wood glazed and skeleton shutters open rebated and prepared to receive glass guage etc with rebated sash bars, and number of edges framin plan chamfered or rounded fitted with cut and mitred beads for securing glass etc, size SSR Part-I section 8 clauge 8.324 (a) complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as per specified and directed by the Engr-in-charge.

S&F4 mm thick figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane complete all as per specified and directed by the Engr-in-charge.

M&L for preparation of new wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as per specified and directed by the Engr-in-charge.

M&L for preparation of new /untreated steel surfaces of any descirption not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over one coat of red oxide complete all as per specified and directed by the Engr-in-charge.

M&L for steel windows or ventilators,fixed type,with glazing bars,including a shop coat red oxide of zinc chrome primer, complete all as per specified and directed by the Engr-in-charge.

S & F kitchen sinks with drainage board made of stainless steel 1mm thick overall size 915mm X 460mm bowl size 410mm X 330mm X 160mm with plugs, incl bedding in cement mortar and fixing cantilever brackets, waste coupling & PVC waste pipe complete fixed in repair complete all as per specified and directed by the Engr-in-charge.

M&L for 750mm x 600mm x 250mm plate rack made out of 1.00m thick stainless steel sheet with steel shelves and hanging arrangement for utensil, complete all as specified and directed fixed in repair complete all as per specified and directed by the Engr-in-charge.

S&F magnet catchers 50mm steel plate MS body and striking plate incl letting in & fixed complete all as per specified and directed by the Engr-in-charge.

M&L for 200 mm aluminium anodised, barrel tower bolts of extruded section complete all as per specified and directed by the Engr-in-charge.

M&L for 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete, all as specified.

M&L for 150 mm aluminium handles, cast type anodised complete all as specified and directed.

M&L for mild steel, 300 mm, ordinary rat tail rod pattern door spring including roller and roller plate in repaircomplete all as per specified and directed by the Engr-in-charge.

M&L for floor door stopper of aluminium power coated alloy long body (as per sample kept in GE's office) and tongue, anodised, with hard drawn steel spring, fixed in floor, 140mm overall length of cover plate complete all as specified and directed.

M&L for 100mm long, stainless steel butt hinges for PVC door, complete all as specified and directed by Engr-in- Charge.

M&L for continuous (piano) hinges width of flaps (when open) 30 mm, mild steel, bright finish or electro galvanised ,complete all as specified and directed by Engr-in- Charge

M&L for 125mm size hasp and staple safty type aluminum anodized with mild steel hinges pin including bolt to hinge plate and fixed with screwcomplete all as per specified and directed by the Engr-in-charge.

M&L for 100 mm aluminium handles, cast type anodised in repair complete all as specified and directed.

M&L for brass chromium plated towel ring round 200mm dia, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

M&L for 20mm dia brass chromium plated tubular towel rails, D type,60 cm long between flanges, fixed in repair, complete all as specified and as directed.

M&L for glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed by Engr-in-Charge.

M&L for corner Glass self ( With CP brakets) 225 x 225 mm complete all as specified and as directed.

M&L for centre hole mixer for mixing hot & cold water for wash hand basin, cast copper alloy, with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe suitable for 15mm bore, fixed in repair complete all as specified and directed.

S&F fixed in repair viterous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, witht integral foot rests (excluding flushing cistern and flush pipe) with 'P' or 'S' trap complete all as per specified and directed by the Engr-in-charge.

S&F plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, fixed in repair,complete all as per specified and directed by the Engr-in-charge.

S&F 10 Ltr PVC valveless syphonic action type flushing cistern low level white with inlet including bracket and 32mm flush pipe of polythylene ball valve,float and handleof low or high density and 15mm PVC connection 450mm long complete all as per specified and directed by the Engr-in-charge.

S&F Viterous china wash basin pedestral type white flat back size 550 x 400mm incl waste couping CP 32mm dia chain and plug and porcelan stopper and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP getting with holes complete all as specified and directed by Engr-in-Chare.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as per specified and directed by the Engr-in-charge.

S&F PVC connection 15mm size with PTMT nuts of length 650mm complete all as per specified and directed by the Engr-in-charge.

S&F vitreous china urinal,half stall type,white(including pvc connection 15 mm size with PTMT nuts of 300 mm length and angle valves 15 mm bore,fancy type cp,cast copper alloy screwd down high pressure,complete all as specified(excluding flushing cistern&flush pipe and waste pipe) complete all as per specified and directed by the Engr-in-charge.

M&L for 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layer white in colour (inside outside) hoisted and fixed in position incl inlet, outlet and overflow connection nipple of suitable size complete all as per specified and directed by the Engr-in-charge.

M&L for Ball brass valve 25mm dia high pressure with polythene float and fly nut complete all as per specified and directed by the Engr-in-charge.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store 15mm dia complete all as per specified and directed by the Engr-in-charge.

S&F 15 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as per specified and directed by the Engr-in-charge.

Fixing only steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia15 mm, all as specified.

S&F 25 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as per specified and directed by the Engr-in-charge.

S&F 25 mm Gun metal , global or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as per specified and directed by the Engr-in-charge.

S&F stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe 15mm dia complete all as per specified and directed by the Engr-in-charge.

S&F angle valve, brass, chromium plated, fancy type, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed

S&F angle valve,Twin type brass, chromium plated, fancy type, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed.

S&F health faucet, brass, chromium plated, with 1000mm long 8mm dia chrome finish flexible pipe with wall hook, fixed in repair complete all as specified and directed.

M&L for 15mm concealed type stop valve chromium plated, fancy type, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed.

M&L for bib taps, brass, chromium plated, fancy type, long nose, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed.

M&L for shower rose, brass, chromium plated, with CP arm 120mm dia with or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe or union as in repair complete all as specified and directed.

S&F in repairs pillar taps, cast copper alloy, fancy type with capstan heads, chromiuplated,screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15mm complete all as per specified and directed by the Engr-in-charge.

S&F soap dish, brass, chromium plated, heavy duty, fixed to wall with plugs with brass cromium plated screws, fixed in repair complete all as specified and directed

S&F CP brass grating 100mm dia, centre hole, fixed in repair complete all as specified and as directed.

S&F CP brass grating 100mm dia, fixed in repair complete all as specified and as directed.

S&F toilet paper holder, brass, chromium plated, heavy duty, fixed with brass screw complete all as specified and as directed.

S&F tumbler holder, brass, chromium plated, heavy duty, having suitable recesses made for hanging necessary bath items complete fixed with brass screws as per manufacturer's instructions complete all as per specified and directed by the Engr-in-charge.

S&F 110mm PVC(SWR) pipes single socket in any length with rubber ring joints fixed to walls complete all as per specified and directed by the Engr-in-charge.

S&F 110mm PVC (SWR) bends any radius complete all as per specified and directed by the Engr-in-charge.

Dismantling cast iron work of any description etc complete all as specified and directed by Engineer-in-Charge.

S&F 75mm cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4 of size 200mm x200mmx250mm, fixed in repair , complete all as specified and directed by Engineer-in-Charge.

S&F 150 x 150mm size salt glazed stoneware gully traps, square or round mouthed type ‘P’ , fixed in repair , complete all as specified and directed by Engineer-in-Charge.

S&F 100mm bore cast iron traps P or S fixed in repair , complete all as specified and directed by Engineer-in-Charge.

S&F stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75/100/110mm bore pipe fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F Cast iron cowls 100mm bore complete all as per specified and directed by the Engr-in-charge.

S&F 75mm bore cast iron sand cast soil waste and vent pipe in any length with or without ears with cement joint fixed to walls with mild steel Clamp including takind down of existing pipe complete all as specified and directed by Engineer-in-Charge.

S&F Cast iron soil, waste and vent pipes 100mm dia in any length with or without ears(Sand cast), with cement joints,complete all as per specified and directed by the Engr-in-charge.

S&F 100mm bore cast iron sand cast soil waste and vent pipe in any length with or without ears with cement joint fixed to walls with mild steel Clamp including takind down of existing pipe complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore cast iron branch pieces, single, (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches suitable for cast iron soil waste discharge pipe fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F 100mm bore cast iron bend (any radius) with duck's foot or heel rest fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore cast iron bend (any radius) with duck's foot or heel rest fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F 100mm bore cast iron diminishing pieces/junction plain any radius fixed as reducer, suitable for CI spun pipes fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore cast iron diminishing pieces / junction plain any radius fixed as reducer, suitable for CI spun pipes fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F aluminium deco gril of 5 to 6 mm dia in size of mesh not exc 7.5mm in either direction as approval by GE all as directed by Engineer-in- Charge.

18/19mm thick medium density fiber board (MDF) designs/ fancy shed exterior finished PVC laminated one side, interior grade, one side decorated laminated approval colour and other balancing site white in colour, cut to size as per required and fized in position for cabinates including PVC edges bonding tap of some shade and side fixed SR adhensive etc, complete all as specified and directed and approval by AGE/ GE.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with PVC insulted unsheathed, FRLS 1100 volts grade stranded copper conductor cable single core 1.5 Sqmm for one light/fan point controlled by one way switch, and wire to be drawn in and including MS sheet metal 1.2 mm thick switch board of suitable size be fixed flush wall, with 3 mm thick ebonite sheet cover and necessary screws, cap washers etc, or to be fixed on wall repectively and then making good as per existing as directed by EIC and providing earth continuity wire using PVC unsulated, un sheathed single core standard copper conductor FRLS cable of size 1.5 Sqmm. (Cutting chases for counduits shall be measured and paid separately ) light point / fan point controlled by one switch SP 5 amps 240 V.

All as per item No.154 above but for one 5 Amps socket outlet on independent board.

All as per item No. 154 above wire size 2x2.5 Sqmm and providing earth continuity wire using PVC insulated, unsheathed single core stranded copper stranded copper conductor FRLS cable of size 2.5 Sqmm. To controlled the 3 pins 5 / 15 Amps socket outlet on independent board.

M&L for point wring for one light/ceiling fan controlled by one switch with 1.5 Sqmm (nominal area) PVC insulated and PVC unsheathed multi stranded copper conductor cable FRLS in and including concealed PVC conduit 20 mm dia medium duty ISI marked, including sutiable new steel sunken boxes,modular frame and cover plate for fixing of modular switches as per required point in that board, flush to surface for one light point, fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 Sqmm copper conductor cable FRLS connected to common earth dooly complete including cutting,chasing the surface and then making good the same in CM 1:3 complete all as specified and directed. One light point /ceiling fan/exhaust fan/bell point controlled by one switch (a) One light point /ceiling fan/exhaust fan/bell point controlled by one switch

All as per item No.157 above but for one 3/5 pin socket outlet, 5 Amp independent

All as per item No.157 above but for one socket outlet 3 Pin, 5 Amps, SP on same board.

M&L for point wring for power point controlled by one switch with 2.5 Sqmm (nominal area) PVC insulated and PVC unsheathed multi stranded copper conductor cable FRLSH in and including concealed PVC conduit 20 mm dia medium duty ISI marked, including sutiable new steel sunken boxes,modular frame and cover plate for fixing of modular switches as per required point in that board, flush to surface for one light point, fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 2.5 Sqmm copper conductor cable FRLSH connected to common earth dooly complete including cutting,chasing the surface and then making good the same in CM 1:3 complete all as specified and directed.

M&L for point wiring with 1.5 Sq. mm PVC Insulated unsheathed FRLS multistranded copper conductor, medium grade ISI meraked drwan into and including PVC concealed conduit with all accessories from terminal box to junction of ceiling and wall and rest of circuit conductor wire drwan in to and including suraface PVC rigid non metalic conduit for one ceiling fan point controlled by one switch with and also including 1.5 Sqmm continious earth wire connected to common earth dolly complete all as specified and directed by Engr -in- charge.

All as per item No. 161 above but for bell / buzzer on independent board controlled by one push button bell switch.

All as per item No. 161 above but for one 3/5 pin socket outlet, 5 Amp independent

All as per item No. 161 above but for wire size 2x2.5 Sqmm controlled the 3 pin 5 / 15 Amps socket outlet on independent board.

All as per item No. 161 above but controle by 2 Nos.of two way switch.

All as per item No. 161 above but one socket outlet 3 Pin, 5 Amps, SP on same board.

M&L for cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed conduit wiring, etc, and making good, cutting not exc 10 cm girth complete all as specified and directed by Engr -in- charge.

S&F Two in one, 3 Pin, 5 Amps, flush type socket outlet complete all as directed by Engineer- in - Charge.

S&F in replacement modular switch single pole one way 10Amps 1 module complete all as specified and directed by Engr -in- charge.

S&F in replacement modular switch single pole one way 16 Amps 1 module complete all as specified and directed by Engr -in- charge.

S&F in replacement modular socket 6 amp-2/3 pin combined 2 module complete all as specified and directed by Engr -in- charge.

S&F in replacement modular Bell push 6 amp 01 module complete all as specified and directed by Engr -in- charge.

S&F in replacement modular socket 6 /16 Amps 2/3 pin flush type complete all as specified and directed by Engr -in- charge.

S&F in replacement modular electronic fan regulator, step type, two module 60 watt 230 volt and making all necessary connections complete all as specified and directed.

S&F stepped type, electronic fan regulator, flush type on the existing phenolic laminated sheet etc. as required complete all as directed by Engineer- in - Charge.

S&F calling bell, suitable for 230 Volt, 50 Hz, single pole, AC supply complete all as directed by Engineer- in - Charge.

S&F push bell switch piano, flush type, white colour, single pole, 5 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F bell ding dong AC 23Volts single pole complete all as specified and directed by Engr -in- charge.

Taking down existing serviceable tube light fittings any type any wattage and keep in safe custody for refixing the same after rewiring complete all as specified and directed by Engr -in- charge.

Fixing only Slim linear LED lighting fixture 4/5W watt LED batten, with full base of extruded poly carbonate isolated driver, complete making all connection from ceiling rose to fittings including testing complete all as per the direction of Engr-in-Charge.

Fixing only decorative ultra slim linear aluminium extruded LED lighting fixture 10/12 Watt LED of input voltage AC 220V-240V, 50 Hz with colour tempetrature 6500K more than 1080 lumens of IP 20 complete making all connection using 1.5 Sqmm copper conductor multistranded PVC insulated twin core flexible cable from ceiling rose to fitting complete all as per directed by Engr-in-charge.

Fixing only slim linear LED lighting fixture 20 Watt LED batten, P.F greater than 0.9, input voltage range from 90 Volts to 280Volts with full base of polycarbonate extruded section acting as a heat sink with closed back isolated driver complete making all connection using 1.5Sqmm copper conductor multistranded PVC insulated 2 core flexible cable with from ceiling rose to fitting complete all as per the direction of Engr-in-Charge

Fixing only LED Bulk head (6500K) fitting of 09/10 Watt surface mounting type extruded aluminium body with diffuser complete with testing complete all as per the direction of Engr-in-Charge

S&F LED light fitting PLUTO NEO PANEL 2'x2' PLR 36 watt LED 857S environmental friendly , new generation , aesthetically designed ,ultra modern recess mounting luminaire with high brightness SMD LEDs as light source suitable for armstrong /grid /ceiling complete all as per the direction of Engr-in-Charge

S&F switch Piano, flush type, two way, single pole, 5 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F switch Piano, flush type, One way , single pole, 5 Amps, suitable for 240 V, 50 Hz, Ac supply completed all as directed by Engineer-in-Charge.

S&F switch socket combination 5 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F switch socket combination 5 / 15 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F switch Piano, flush type, One way , single pole, 15 Amps, suitable for 240 V, 50 Hz, AC supply completed all as directed by Engineer-in-Charge.

S&F two in one, 3 Pin, 5 Amps, flush type outlet complete all as directed by Engineer-in Charge.

S&F socket outlet, flush type, One way, single pole, 15 Amps, suitable for 240 V, 50 Hz, AC supply complete all as by Engineer-in-Charge.

S&F ceiling rose, 3 terminal, PVC / ploycarbonet, islolated body complete all as directed by Engineer-in-Charge.

S&F Slim linear LED lighting fixture 20 watt LED batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, complete making all connection using 1.5 Sqmm copper conductor multistrandard PVC insulated 2 core flexiable cable with flexiable PVC pipe from ceiling rose to fittings complete including taking down old US tube light fitting 1x36W and taken in schedule of credit all as per the direction of Engr-in-Charge. Make- Havells or equilent to CG/ syska CAT No SSK SQ2001 as sample approved by Acepting officer.

S&F in replacement E-Lite LED Curve lighting fixture 10/12 watt LED batten, with full base of extruded polycarbonate body environmental friendly, energy efficient ready to use pack with isolated driver, complete making all connection using 1.5 Sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete all as per the direction of Engr-in-Charge.

S&F in replacement E-Lite LED Curve lighting fixture 05 watt LED batten, with full base of extruded polycarbonate body environmental friendly, energy efficient ready to use pack with isolated driver, complete making all connection using 1.5 Sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete all as per the direction of Engr-in-Charge.

S&F in replacement security (street) light fitting 35 watt, new generation energy saving & environmental friendly long life versatile pressure die cost aluminium IP 66 with acylic, powder coated, pressure die cast aluminium compact high power LED street light with heat resistant toughed glass, corrosion resistant, isolated driver, including provision of GI tubing bracket of suitable size and fixed on wall including clamps, nut, bolts and washer for fixing of security (street) light complete all as per direction of Engr-in-Charge.

S&F in replacement Slim linear LED lighting fixture 4W watt LED batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, complete making all connction from ceiling rose to fittings including testing complete all as per the direction of Engr-in-Charge. Make - Make of LED - SYSKA as per ordering code SSK-SQ0401-4W or equivalent model of Havells or CG as sample approved by accepting officer

M&L for submain wiring with 2X6.0 SqmM+1X6.0SqmM Earth Wire single core PVC insulated FRSL sheathed cooper cable connecting to common earth dolly in and including heavy duty PVC Concealed Conduit as per site requirement including taking down old us submain wiringand direction by EIC, all accessories complete all as specified and directed.

M&L for submain wiring with 2X4.0 SqmM+1X4.0SqmM Earth Wire single core PVC insulated FRSL sheathed cooper cable connecting to common earth dolly in and including heavy duty PVC Concealed Conduit as per site requirement including taking down old us submain wiringand direction by EIC, all accessories complete all as specified and directed.

M&L for earthing complete with GI earth plate electrols 600mmx60mmx6mm thick burried in ground vertically to a depth not less than 2.25meters below ground level with top edge of the earth plate at a depth not less than 1.5 meter below Normal ground level, earth plate surrounded 15cm thick layers of common salt and charcoal dust starting from ground below 15 cm of earth plate and up to 15 cm above the same. GI plate connected with galvanished earth lead wire 4.0mm dia by means of GI nuts, bolts and washers of galvanished iron or steel all as shown in electrical plate no. 5 connecting to earth test point all as specified or indicated including testing on complition with following:- (a) Test point GI wire 4mm dia. (b) Watering pipe GI light grade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embededin floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm constructed in PCC 1:2:4 type earth B1 exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC pit cover 25mm thick with 2 Nos MS handles of 12mm dia suitable for carring of pit cover (d) Angle iron frame made of 40x40x4 mm angle iron for 30x30 mm PCC pit for holding the pit cover.

S&F 4mm dia GI wire as earth continuty conductor or main earth strip fix to wall on batten or recess or chess or burrid in ground or any other indicated situation for loop earthing etc complete all as directed by Engineer- in - Charge.

Taking down serviceable MCB DB with MCB etc after disconnecting for re use or for credit complete all as directed by Engineer- in - Charge.

S & F sheet metal TPN DBs - DPX3 160 MCCB DBs 04 way (DPX³ 250+12) with metal door 415 volts grade IP 43 Protection Grade fixed flush to wall complete including connections should be provide with necessary reducer lugs all as specified and directed by Engr-in-charge.

S & F DPX3 thermal magnetic MCCB 4 pole 160 Amps 415 Volts 16 ka INCLUDING MAKING NECESSARY ARRANGEMENT all as specified and directed by Engineer- in - Charge.

S & F single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 8 ways. complete all as directed by Engineer- in - Charge.

S & F in repair sheet metal enclosure double door single pole and netural 240 Volts for DB's when MSBs to be used 4 way with 200 amp rated bus bar with IP-43 protection complete all as directed by Engr-in-Charge.

S & F single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 12 way complete all as directed by Engineer- in - Charge.

S&F MCB SPN 40 Amps, 240 Volts, 'C' Curve completed all as directed by Engr-in-Charge.

S&F MCB SP,6 to 32 Amps, 240 Volts, rupturing capacity 10 KA "C" Series. complete all as directed by Engr-in-Charge.

Taking down serviceable/unserviceable electric meter including meter box from existing position carefully for refixing including making good to disturbed surfaces complete all as directed by Engineer- in - Charge. (Note : Disturbed surfaces should making good by Plastering/distembering/colour washing/white washing to match with existing surfaces)

M&L for re fixing of serviceable electric meter obtained from item No 213 with meter box by scouting to the wall and fix firmely complete all as directed by Engineer- in - Charge.

S & F sheet metal TPN DBs - DPX3 160 MCCB DBs 04 way (DPX3 160+ 12) with metal door 415 volts grade IP 43 Protection Grade fixed flush to wall complete including connections should be provide with necessary reducer lugs all as specified and directed by Engr-in-charge.

S & F DPX3 thermal magnetic MCCB 3 pole 100 Amps 415 Volts 16 ka INCLUDING MAKING NECESSARY ARRANGEMENT all as specified and directed by Engr-in-charge.

Taking down ceiling fan/exhaust fan sealing cable end etc and shifting to store complete and rehanging the same after overhauling and painting with white synthetic enamel paint(two coat) with the help of spray gun and connecting with three core flexible copper conductor cable 0.75 sq mm complete all as directed by Engr-in-Charge.

S&F of rigid non metallic PVC conduit medium grade, 25 mm dia (external) inclusive of all fittings such as tees, bends, elbow, reducers,Junction box, with modular sheet cover, bell mouth tube ends etc and all fixing accessories such as couples, bolts, nuts, saddles, pipe hooks etc including cutting and chasing and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as specified and directed. (For Telephone wiring)

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as directed by Engr-in-Charge.

M & L for replacement of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps 240 volt capacity complete all as directed.

S&F heavy duty turbo force single phase exhaust fans PVC VENTIL AIR DXZ WHITE of 150mm sweep complete including fixing exhaust fan with grouting of nut & bolts complete Make HavellsVENTIL AIR DXZ WHITE or equivallent to other makes of crompton Greeves / Bajaj all as per specified and directed by Engr-in-Charge.

Supply and lay in replacement XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core in trenches/floor/pole/GI pipe complete including cutting of bituminous roadf/chasing to any surface and making good to the disturbed surface to match the existing complete all as directed by Engr-in-Charge.

Supply and lay in replacement XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core in trenches/floor/pole/GI pipe complete including cutting/chasing to any surface and making good to the disturbed surface to match the existing complete all as directed by Engr-in-Charge.

Supply and lay in replacement XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminiumconductor of size 25 sq mm 4 core in trenches/floor/pole/GI pipe complete including cutting/chasing to any surface and making good to the disturbed surface to match the existing complete all as directed by Engineer- in - Charge.

M&L for dry sand cushioning to under ground cables provided cables provided with layer of sand 8 cm deep before laying the cable, 15 cm depth after laying cable & stretching the cable complete all as directed by Engr-in-Charge.

Supply and lay brick class 'B' covering as mechanical protection to cable with well burnt complete all as directed by Engr-in-Charge.

M&L for GI tubing light grade with all fiting and fixed in wall and floor or fixed to pole of size 40mm dia complete all as directed by Engr-in-Charge.

M&L for cutting of road n.exc 45 Cm depth, and n.exc 30 Cm width for laying of GI tubing for protection of cable including making concrete in ground floors and paving all as per existing complete all as directed by Engr-in-Charge.

S&F on load change over switch 4 pole 415 V in sheet metal enclosure 4 pole of capacity 100 Amp complete all as directed by Engineer- in - Charge.

M/S GURU DEV BUILDERS

RAMAN KUMAR