Fabrication and placement of office furnishings for admin, PFFF and ZFF office building at NFC Kota.

Amount

Supplying & Placing Modular table in completely knock down conditions with an overall size 2100mm X 1800mm X 750mm that is to be assembled at site. The top shall have the size 1900mm X 900mm made up of 45mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported on 75mm Peg mounted over side storage unit and fixed pedestal. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 45mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick Pre-laminated particle board in linear shape with appropriate PVC edge banding connected with both end. The table shall have side unit for storage purpose with an overall size 1800mm X 510mm X 625mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with top and side 45mm thick and drawer base 9mm thick & other parts 18mm thick like shutter, back, facia, etc. It shall have 3 drawer and 2 sliding shutter. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A hanging pedestal shall be provided with an overall size 455mm X 685mm X 485mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, facia shall be 18mm thick & drawer base shall be 9mm thick. The pedestal shall have 2 nos. of drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of sliding channels to enable operation. The drawer shall have central locking mechanism in which all the drawer shall be locked with one single key.

Supplying & Placing Modular table in completely knock down conditions with an overall size 1800mm X 1650mm X 750mm that is to be assembled at site. The work top shall have the size 1600mm X 900mm made up of 45mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported on 75mm Peg mounted over side storage unit at one side and fixed pedestal at another side. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 45mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick Pre-laminated particle board in linear shape with appropriate PVC edge banding connected with both end. The table shall have side unit for storage purpose with an overall size 1650mm X 510mm X 625mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with top and side 45mm thick and drawer base 9mm thick & other parts 18mm thick like shutter, back, facia, etc. It shall have 3 drawer and 2 sliding shutter. The drawer shall be operated with SS handle and easily close & open with the assistance of roller base channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The top shall be enclosed by single sided flaper box that houses telephone cable, data and power connection discretely. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A hanging pedestal shall be provided with an overall size 455mm X 510mm X 485mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, facia shall be 18mm thick & drawer base shall be 9mm thick. The pedestal shall have 2 nos. of drawer operated with SS handle and easily close & open with the assistance of roller and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be locked with one single key. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supplying & Placing executive table with credenza unit and pedestal unit in completely knock down conditions with an overall size 1650mm X 1900mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall have the size 1650mm X 800mm made up of 50mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be enclosed with wire manager cap for electric provision. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 300mm. The trey shall be operated on sliding channel. The table top shall be supported on particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board in linear shape with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have credenza unit for storage purpose with an overall size 1100mm X 450mm X 650mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 box drawer, 1 filing drawer and 1 shutter. It should be operated with the assistance of SS handle, concealed crank hinge and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. It shall be mounted on injection moulded nylon castor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 650mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over injection moulded nylon castor. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supplying & Placing executive table with credenza unit in completely knock down conditions with an overall size 1600mm X 1600mm X 750mm that is to be assembled at site. The worktop shall have the size 1600mm X 700mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on CRCA powder coated rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. The table shall be clad with 1mm thick modesty panel which provide structural support for the table. It should be 1mm thick with star perforation CRCA powder coated sheet in linear shape. The understructure shall consist of loop leg and C-type leg made up of CRCA powder coated triangular shape pipe having cross-section area 53mm X 53mm X 75mm with 1.6mm thick. There shall be shoe provided at the base to avoid scratches on the floor. Side top shall be provided with an overall size 900mm X 570mm X 750mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823. It shall be supported on peg which is mounted on credenza unit. The credenza unit shall have overall size 1400mm X 575mm X 500mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 box drawer, 1 filing drawer and 1 shutter. The drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The shutter shall be operated by SS handle and concealed crank hinge. The credenza unit shall be mounted over CRCA powder coated U shape leg having cross-section area 53mm X 53mm x 75mm with 1.6mm thick. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supplying & placing executive table in completely knock down conditions with an overall size 1500mm X 750mm X 750mm that is to be assembled at site. The worktop shall be made up of 25mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The table shall be clad with modesty panel which provide structural support for the table. It should be 1mm thick CRCA star perforated sheet connected with both end. The table understructure shall consist of C frame MS/CRCA leg having cross-sectional area 60mm X 30mm. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 660mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted on injection moulded nylon castor. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supplying & Placing Modular table in completely knock down conditions with an overall size 2800mm X 2000mm X 750mm that is to be assembled at site. The worktop shall have the size 2400mm X 1000mm x 50mm thick made up of Medium Density Fibre-board with approved laminate. The table top profile shall be in rectangle shape. The table top shall be supported on pedestal on one side and on the other side a side unit. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre-board in linear shape with appropriate PVC edge banding and laminate. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 2000mm x 600mm X 600mm. It shall have 2 nos. of drawer, 2 nos. of filling space with door and 1 nos of open space. The pedestal shall have 3 nos drawer and 2 Nos filling space with door. The drawer shall be operated with profile handle and easily close & open with the assistance of sliding channels to enable smooth operation and sliding rail track and concealed crank hinge. Drawer facai, sides and all other shall be made in 18mm thick and drawer base shall be 9mm thick. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom.

Supplying & Placing Modular table in completely knock down conditions with an overall size 2600mm X 1900mm X 750mm that is to be assembled at site. The worktop shall have the size 2200mm X 1000mm x 50mm thick made up of Medium Density Fibre-board with approved laminate. The table top profile shall be in rectangle shape. The table top shall be supported on pedestal on one side and on the other side a side unit. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre-board in linear shape with appropriate PVC edge banding and laminate. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 1900mm x 600mm X 600mm. It shall have 2 nos. of drawer, 1 nos. of filling space with door and 1 nos of open space . The drawer shall be operated with profile handle and easily close & open with the assistance of sliding channels to enable smooth operation and sliding rail track and concealed crank hinge. Drawer facai, sides and all other shall be made in 18mm thick and drawer base shall be 9mm thick. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom.

Supplying & placing executive table in completely knock down conditions with an overall size 1500mm X 750mm X 750mm that is to be assembled at site. The worktop shall be made up of 25mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The table shall be clad with modesty panel which provide structural support for the table. It should be 1mm thick CRCA star perforated sheet connected with both end. The table understructure shall consist of C frame MS/CRCA leg having cross-sectional area 60mm X 30mm. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 660mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted on injection moulded nylon castor.The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be made of metal insert pipe frame padded with high resilience polyurethane foam 40mm thick having density 40kg/m³ in seat and 19mm thick having density 23kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support as well as head support. The chair shall be supplied with chrome plated metal arm with black integral polyurethane top. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti-shock feature which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged MS CRCA chrome plated having pitch circle dia. 660 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 480±10 mm(D) X 475±10 mm(W) and back size shall be 465±10 mm(W) X 700±10 mm(H) from seat. Overall height shall be = 1160±10 mm, overall depth = 600±10 mm & overall width = 550±10 mm.

Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be made of metal insert pipe frame padded with high resilience polyurethane foam 40mm thick having density 40kg/m³ in seat and 19mm thick having density 23kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support. The chair shall be supplied with chrome plated metal arm with black integral polyurethane top. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti-shock feature which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged MS CRCA chrome plated having pitch circle dia. 660 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 460±10 mm(D) X 475±10 mm(W) and back size shall be 465±10 mm(W) X 510±10 mm(H) from seat. Overall height shall be = 980±10 mm, overall depth = 620±10 mm & overall width = 560±10 mm.

Providing and supplying a visitor chair with ergonomic design for user comfort & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be metal insert pipe frame padded with high resilience polyurethane foam 40mm thick having density 40kg/m³ in seat and 19mm thick having density 23kg/m³ in back. The seat and back shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine for lumbar support. The chair shall be supplied with chrome plated metal arm having black integral covering top and powder coated steel spine shall be joint with seat and back. The frame structure shall be cantilever support type made up of MS CRCA chrome plated round pipe of dia. 28mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 480±10 mm(D) X 480±10 mm(W) and back size shall be 485±10 mm(W) X 510±10 mm(H) from seat. Overall height shall be = 980±10 mm, overall depth = 600±10 mm & overall width = 560±10 mm.

Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back frame shall be made up of the wooden structure padded with high resilience polyurethane foam (50+25+30)mm thick having density (40, 32 & 32)kg/m³ in seat and (30+25)mm thick having density (32, 32)kg/m³ in back. The same shall be upholstered with leatherette tapestry 0.8±0.2mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine for lumbar support which helps to provide full back support. Seat and back shall be covered with polished wooden at both side for decorative appearance. The chair shall be supplied with wooden cushion arm having melamine polish. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have metal insert CRCA covered with natural wood having pitch circle dia. 630 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(D) X 510±10 mm(W) and back size shall be 520±10 mm(W) X 725±10 mm(H) from seat. Overall height shall be = 1185±10 mm, overall depth = 720±10 mm & overall width = 650±10 mm.

Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back frame shall be made up of the combination of 15mm thick hot pressed commercial plywood and ply-board padded with high resilience polyurethane foam (50+25+30)mm thick having density (40, 32 & 32)kg/m³ in seat and (30+25)mm thick having density (32, 32)kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine for lumbar support which helps to provide full back support as well as head support. Seat and back shall be covered with polished wooden at both side for decorative appearance. The chair shall be supplied with natural wood arm having melamine polish and die cast aluminium end caps. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have metal insert CRCA covered with natural wood having pitch circle dia. 630 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 510±10 mm(D) X 510±10 mm(W) and back size shall be 525±10 mm(W) X 710±10 mm(H) from seat. Overall height shall be = 1170±10 mm & overall width/depth = 740±10 mm.

Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back frame shall be made up of the combination of 15mm thick hot pressed commercial plywood and ply-board padded with high resilience polyurethane foam (50+25+30)mm thick having density (40, 32 & 32)kg/m³ in seat and (30+25)mm thick having density (32, 32)kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine for lumbar support which helps to provide full back support. Seat and back shall be covered with polished wooden at both side for decorative appearance. The chair shall be supplied with natural wood arm having melamine polish and cushion base leatherite covering top. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged metal insert CRCA covered with natural wood having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 510±10 mm(D) X 530±10 mm(W) and back size shall be 525±10 mm(W) X 530±10 mm(H) from seat. Overall height shall be = 1010±10 mm, overall depth = 680±10 mm & overall width = 675±10 mm.

Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be made of metal insert pipe frame padded with high resilience polyurethane foam 40mm thick having density 40kg/m³ in seat and 19mm thick having density 23kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support. The chair shall be supplied with chrome plated metal arm with black integral polyurethane top. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti-shock feature which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged MS CRCA chrome plated having pitch circle dia. 660 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 460±10 mm(D) X 475±10 mm(W) and back size shall be 465±10 mm(W) X 510±10 mm(H) from seat. Overall height shall be = 980±10 mm, overall depth = 620±10 mm & overall width = 560±10 mm.

Supplying & placing storage unit with an overall size 3600mm X 400mm X 2000mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top shall be 25mm thick, base 9mm thick and all other profile i.e. side, back, shutter, facia, shelf, skirting shall be 18mm thick. The edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have shutter shall be provided for closing and opening the storage. The shutter shall be operated with concealed crank hinge with SS handle as well as MP lock mechanism. The top shutter shall be made in 18mm thick pre laminated particle board. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying & placing storage unit with an overall size 800mm X 550mm X 2000mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top shall be 25mm thick, base 9mm thick and all other profile i.e. side, back, shutter, facia, shelf, skirting shall be 18mm thick. The edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 4 nos. of shutter shall be provided for closing and opening the storage. The shutter shall be operated with concealed crank hinge with SS handle as well as MP lock mechanism. The top shutter shall be made in aluminium extrution and glass, the bottom shutter shall be made in 18mm thick pre laminated particle board. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying & placing storage unit with an overall size 1200mm X 400mm X 2000mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top shall be 25mm thick, base 9mm thick and all other profile i.e. side, back, shutter, facia, shelf, skirting shall be 18mm thick. The edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 6 nos. of shutter shall be provided for closing and opening the storage. The shutter shall be operated with concealed crank hinge with SS handle as well as MP lock mechanism. The top shutter shall be made in aluminium extrution and glass, the bottom shutter shall be made in 18mm thick pre laminated particle board. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying & placing storage unit with an overall size 1600mm X 400mm X 2000mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top shall be 25mm thick, base 9mm thick and all other profile i.e. side, back, shutter, facia, shelf, skirting shall be 18mm thick. The edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 8 nos. of shutter shall be provided for closing and opening the storage. The shutter shall be operated with concealed crank hinge with SS handle as well as MP lock mechanism. The top 2 shutter shall be made in aluminium extrution and glass, other 2 shall be made in 18mm thick pre laminated paticle board and the bottom shutter shall be made in 18mm thick pre laminated particle board. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying & placing storage unit with an overall size 1200mm X 400mm X 800mm. It storage should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. All profile i.e. side, back, top, shutter, facia, shelf, skirting shall be 18mm thick and base 9mm thick. The top and side shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 2 nos. of drawer, 2 nos. of adjustable shelf and 2 nos. of shutter. The drawer and shutter shall be operated with roller channel to enable smooth operation and concealed crank hinge with SS handle. The drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key and shutter shall have MP lock. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying & placing storage unit with an overall size 300mm X 300mm X 900mm. It storage should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The side and top, shall be 25mm thick and All other shall be made in 18mm thickness. The top and side shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 2 nos. of adjustable shelf and 1 nos. of shutter. The shutter shall be operated on concealed crank hinge with SS handle. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying & placing storage unit with an overall size 1600mm X 400mm X 820mm. The storage shall be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top shall be made up of 25mm thick and other parts like side, back, shutter, facia, skirting shall be 18mm thick. The edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall be supplied with 2 nos. of shelves. Door shutters shall be provided for opening and closing the storage. The shutter shall be operated with concealed crank hinge and die cast handle as well as proper locking arrangement. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying & placing storage unit with an overall size 2000mm X 400mm X 820mm. The storage shall be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top shall be made up of 25mm thick and other parts like side, back, shutter, facia, skirting shall be 18mm thick. The edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall be supplied with 2 nos. of shelves. Door shutters shall be provided for opening and closing the storage. The shutter shall be operated with concealed crank hinge and die cast handle as well as proper locking arrangement. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying & placing storage unit with an overall size 900mm X 450mm X 1200mm. The storage shall be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top shall be made up of 25mm thick and other parts like side, back, shutter, facia, skirting shall be 18mm thick. The edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall be supplied with 2 nos. of shelves. Door shutters shall be provided for opening and closing the storage. The shutter shall be operated with concealed crank hinge and die cast handle as well as proper locking arrangement. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The back shall be designed in manchested chesterfield design. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with pure leather tapestry. The understructure shall wood and designer legs of SS with electroplated finish. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 1540±10 mm(W), seat height = 435±10 mm, overall width = 1900±10 mm, overall depth = 770±10 mm & overall height = 800±10 mm.

Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The back shall be designed in manchested chesterfield design. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with pure leather tapestry. The understructure shall wood and designer legs of SS with electroplated finish. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 540±10 mm(W), seat height = 435±10 mm, overall width = 915±10 mm, overall depth = 770±10 mm & overall height = 800±10 mm.

Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with leather. The understructure shall consist of pipe frame loop leg of SS shiny chrome finish having cross-section area 40mm X 20mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 1540±10 mm(W), seat height = 435±10 mm, overall width = 1900±10 mm, overall depth = 770±10 mm & overall height = 800±10 mm.

Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The complete structure shall be upholstered with leather. The understructure shall consist of SS 202 grade loop leg with shiny chrome finish having cross-section area 40mm X 20mm with 1.6mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 1040±10 mm(W), seat height = 435±10 mm, overall width = 1360±10 mm, overall depth = 770±10 mm & overall height = 800±10 mm.

Supplying and placing single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with leather. The understructure shall consist of pipe frame loop leg of SS shiny chrome finish having cross-section area 40mm X 20mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 540±10 mm(W), seat height = 435±10 mm, overall width = 915±10 mm, overall depth = 770±10 mm & overall height = 800±10 mm.

Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with leather. The sofa shall be supported on MS powder coated pipe frame having size 40mm X 20mm. The under structure shall consist of MS powder coated round leg with upper dia. 38mm and lower dia. 30mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 570±10 mm(D) X 1660±10 mm(W), seat height = 425±10 mm, overall width = 2020±10 mm, overall depth = 750±10 mm & overall height = 665±10 mm.

Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with leatherate tapestary. The sofa shall be supported on MS powder coated pipe frame having size 40mm X 20mm. The under structure shall consist of MS powder coated round leg with upper dia. 38mm and lower dia. 30mm. There shall be PPCP shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 570±10 mm(D) X 1100±10 mm(W), seat height = 425±10 mm, overall width = 1490±10 mm, overall depth = 750±10 mm & overall height = 665±10 mm.

Providing and supplying centre table with an overall size 1400mm X 700mm X 400mm. The top, sides, bottom and drawer facia shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. It shall also have a drawer.

Supplying & placing center table with an overall size 1200mm X 600mm X 400mm. The top shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The side clad of the table shall be 18mm thick particle board. The under structure shall consist of SS 202 grade pipe frame cross-section area 50mm X 10mm. There shall be PPCP shoe provided at the base to avoid scratches on the floor.

Supplying & placing center table with an overall size 600mm X 600mm X 400mm. The top shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The side clad of the table shall be 18mm thick particle board. The under structure shall consist of SS 202 grade pipe frame. There shall be PPCP shoe provided at the base to avoid scratches on the floor.

Providing and supplying centre table with an overall size 1200mm X 1200mm X 410mm. The top should be made up of 75mm thick, it would be 25mm at mid and 75mm at sides. The MDF top should have decorative finish with approved veneer and PU polish accordingly. The understructure shall consist of 4 nos. of MS sheet gold leg with 6mm thick.

Providing and supplying Side table with an overall size 490mm X 700mm X 500mm. The top, sides, bottom and drawer facia shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. Another top shall be added on the top of the side table made in 25mm thickness.

Providing and supplying Side table with an overall size 490mm X 490mm X 500mm. The top, sides, bottom and drawer facia shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. Another top shall be added on the top of the side table made in 25mm thickness.

Supplying & Placing Conference table in completely knock down conditions with an overall size Dia. 1600mm X 750mm that is to be assembled at site. The table top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in circular shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table shall be supported on MS powder coated rectangle pipe frame having cross-section area 50mm X 25mm with 1.6mm thick. The table understructure shall have 3 nos. chrome plated reducing leg. There shall shoe provided at the base to avoid scratches on the floor. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Providing, supplying and placing vertical filing cabinet. The overall size of the cabinet shall be 470mm (W) X 620mm (D) X 1040mm (H). The cabinet shall be supplied with 3 nos. of drawer. The drawer shall be operated with aesthetically appealing snap fit ABS plastic handle and ball bearing base sliding channel. All drawers shall be synchronized locked with central locking mechanism by one single key. Uniformly distributed load capacity of each drawer shall be 15/20 Kg. The entire body panel and shelves shall be made of prime quality 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the wall from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom of the cabinet. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-60µ thick.

SANJEEV BROTHERS (BID ID -3239338)