PROVN OF CERTAIN REVENUE AND MINOR WORKS IN AOR OF AGE BHDC AND AGE B/R-I UNDER GE (EAST) DELHI CANTT-10

Amount

S&F Solid PVC Wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame acomplete all as specified and directed.

S&F 10 mm thick toughened frosted glass door shutters of size area exc 1.50 Sqm but not exc 3 Sqm, including necessary floor spring hydraulically regulated, otherside fixed on pivot CP fittings and fixtures, CP handles 300 mm long, CP locking arrangement, necessary cutting & holes moulding and fixed including engraving, emblem and lattering not exc 200 mm complete as per directed by Engr-in-Charge.

S & F factory made UPVC white colour Sliding window Three track area not exceeding 2.00 Sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and required accessories. (Note: The unit rate quoted by contractor includes cost of glass and all other connected accessories. Net Opening will be measured for payment purpose.)

S&F 10 mm thick toughened frosted glass for wall partition, Reception, work station of size as required, including necessary CP fittings arrangment including cutting & holes moulding and fixed including engraving, emblem and lattering not exc 200 mm complete as per directed by Engr-In-Charge.

S & F plain gypsum board panel 12 mm thick on ceiling with and including necessary GI frame work for seamless ceiling used with ' T ' , channel or any section including screws , cleats ,fasteners, clips and all required accessories , hangers etc of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm etc ( Any Design & pattern as approved by GE) complete all as specified and directed.

M&L glazed coloured ceramic tiles, 600x300x7mm thick, in vertical surfaces such as skirting/dado etc, set and jointed in cement slurry, laid over & including 10mm thick rendering in cement mortar 1:4, set, jointed and pointed in white cement mixed with colour pigment to match the shade of tile complete all as specified and as directed.

Supply and fabrication & fixing of Modular wardrobe,cupboards, cabinets, drawers , shelfs, vanity , dressing table including shutters ( depth 45 cm to 70 cm) etc , all front side, bottom, top, two sides and partions etc made out of 15-18 mm thick HDHMR board and back side made out of 8 - 10 mm thick HDHMR board (Action tesa or equivalent ) with machine pressed 0.5 to 0.8 mm thick fabric/glossy colour laminate on all exposed front side and other sides decorative laminations. All exposed edges of boards with machine pressed edge band 0.8mm from rehau Germanetc (colour of laminates , design & paterns of partations/ etc as approved by GE) including all accessories of fittings - Auto/soft closing hinges for shutters , C/J gola profile for handles, telescopic channels 18'' / 20'' long , rollers for smooths sliding of drawers, etc as required complete all as specified and as directed. (Note : Overall net size front side including frame will be measured for payment purpose. Total quantity of both type HDHMR board shall be approximately 4.50 sqm and the contractor's quoted rate shall deemed included keeping in view area of board involved and fitting as well and nothing extra shall be payble on a/c of any misunderstanding)

S & F roller blinds of any size and any colour (non-blackout series) with aluminium head rail, with chain operation complete all as specified and directed by Engr-in-Charge. (Make: Vista/Hunter Douglas)

S & F ready made wall / floor mounted Vanity box made of HDHMR board, both side laminated and front side melamine surface, consisting of the following combination :- (a) Wash Hand Basin 620 mm x 460 mm including brass waste cupling. (b) Base Cabinet 585 mm x 445 mm x 480 mm. (Make : Hindware - DTC brand (Element Soft OAK color) or equivalent as per approved by GE)

S & F Hermetically sliding sealed automatic door for lab size 1200 x 2100 view window 300 x 300 mm complete all as specified and as directed.(Make in VSS) (Note: The unit rate quoted by contractor includes cost of glass and all other connected accessories.)

S & F of Droma XL-C AIDO 4125 Sliding Door (Dorma XL-C 4125, 125 mm Height 2.1 Mtr Approx) Automatic Sliding Door Operator without Lock, with 2 Nos Motion Sensor, 1 Nos Safety sensor, 1 Nos Remote, 2 Nos Glass Claps & all Mechanical parts; Max opening capability 2 Mtrs ; Max Weight 80 Kg Both Leafs. All as specified and as per Manufacturer's Instruction. (Note: The unit rate quoted by contractor includes cost of Toughned glass and all other connected accessories.)

S & F powder coated aluminium anodised section 40 x 44mm x14 gauge for aluminium partition wall in wall in panel 1m x1m covered with 5mm thick plain/frosted tinted glass on top half portion and 5 mm thick Aluminium Composite panel fixed in half bottom portion complete all as specfied and directed.

M&L 50 mm thick PCC 1:2:4, Type B1, using 20 mm graded stone aggregate, below tiles for levelling of existing surface complete all as specified and as directed.

S&F Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, over and including 15 mm thick screed bed in cement morter 1:4 for laying floor finishes set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the shade of tile complete.

M & L for Brick work with sub class 'B' bricks of old size, straight or curved on plan to any radious built in CM 1:6 including demolition of Brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n.exc 4 sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each and removing to store complete all as specified and as directed.

Taking down cement or cement lime plaster , any description on brick or stone walls or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for complete removal of existing treatment on walls, cornices etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots incl preparation of old decorated surfaces of walls and applying 2mm thick wall care putty complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and as directed.

M & L for 15mm thick rendering in CM 1:4 on fair face of brick walls/ concrete surfaces and finished even and fair incl scafolding etc, complete all as specified and as directed.

M & L for 15mm thick rendering in CM 1:6 on fair face of brick walls/ concrete surfaces & finished even and fair incl scafolding etc, complete all as specified.

M & L rendering 10 mm thick on concrete surfaces as in ceiling in CM 1:3, finished even and fair incl scafolding etc, complete all as specified and as directed.

M&L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

S & F solid PVC door frame of size, 50x47mm, made out of 5mm thick plain colour PVC sheet, reinforced with MS square tube fixed with screw/plugs to brick walls complete all as specified and directed. Make : Rajshree / Syntex.

S & F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed .

S&F for pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed.

S&F for factory made steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

S & F for flush shutters 40 mm thick solid core constructions with block boardcore , plywood face panels commercial type on both side complete all as specified and as directed.

S & F 100mm size stainless steel butt hinges fixing with SS screws to PVC door frame welded to frame complete all as specified.

S & F 150mm size flat base type aluminum adodised handles complete all as specified and as directed.

S&F for 150mm long flat base type aluminium anodised,barrel tower bolts of extruded section, complete all as specified and as directed.

S & F 300 mm MS sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

M&L 3 mm thick glass panes ordinary quality and glazing with oil putty in square n .exc 0.50 Sqm in each Pane etc complete, complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) ty D-2 using 40mm graded stone aggregate as in sub base of floor. complete all as specified and as directed.

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) of size 300mmx300mm or 400mmx400mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6, after dismantling floor, hearth or wall tiling with cement mortar bedding (but not backing), complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for glazed ceramic tiles in vertical surface of size 300mm x600mm and 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 10mm thick rendering in CM 1:4, complete all as specified and as directed.

S & F GI tubing 15mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F GI tubing 20mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F in repairs of 15 mm bore size PVC, PTMT bib tap complete all as specified and directed.

S&F in repair 15mm dia Stop/ angle valve of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/ 20mm- 92gms) complete all as specified and as directed.

S&F in repair 20mm dia Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/ 20mm- 92gms) complete all as specified and as directed.

S & F in repairs PVC connection 450 mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer complete all as specified and directed.

S&F in repairs PVC Pipe (SWR) 75mm bore single socketed, in any length with rubber ring joint, laid in floors or in trenches complete all as specified and directed.

S&F in repairs PVC Pipe (SWR) 110mm bore single socketed, in any length with rubber ring joint, laid in floors or in trenches complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bend any radius with ovel access door complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bend any radius with ovel access door complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl.

Dismantling of water tanks 500 ltrs of capacity and removing to store complete all as specified and directed.

S&F for Rotational moulded polyethylene water storage tanks tripple layered (cylindrical vertical with threaded lead) hoisted and fixed in position all as specified in SSR Part-I of Capacity 1000 litres all as specified .

S & F vitreous china squatting pan, 'Orissa' pattern, incl connection to trap and flushing pipe, anti-syphonage pipe etc incl making good to floor fixed in repairs size 580 x 440 mm white, with integral foot rests with 'P' or 'S' trap (excluding flushing cistern but incl flush pipe), complete all as specified and as directed.

S&F in repairs 10 ltrs PVC (white) valve less syphonic action type, flushing cistern, low level, coloured with inlet ball valve, float and handle incl aluminium brackets for bottom support fixing with gitties embedded in wall with drilling machine etc complete all as specified and directed.

M & L for preparation of newly steel and iron surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

Writing letters or figures (Block, Roman, Italic or Indian) n exc. 30 cm high

S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface with bitumenous primer @ 0.30 Ltr/Sqm by forced application complete all as specified including taking down existing roof treatment complete all as specified and directed.

M & L for preparation of new surface of wood and wood based surfaces by knotting, stopping etc of any description exc 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L 3 coats of white wash on ceiling on newly plastered surface incl prepration of surface, complete all as specified and directed.

M&L for preparation of treated surfaces of wall and apply Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed.

M&L 3 coats of white wash on wall on newly plastered surface of wall including prepration of wall complete all as specified and directed.

Cutting into existing manholes for 150mm pipe and connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

Excn in post holes (or similar holes) each n.exc. 0.5 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25 cm, watering and removing surplus soil to a distance n.exc. 50 m and making surface good in soft / loose soil.

M&L Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete.

Cement concrete in foundations, filling and mass concrete in type D2 1:4:8 (40mm graded aggregate) complete all as specified and directed by Engr-in-charge.

M&L MS Steel work in tubular trusses/purline/ column/nut bolts/base plate including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240.complete all as specified and directed by Engr-in-charge.

M&L Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge.

M&L for 75mm thick cement concrete (1:3:6) type C- 2,using (40mm graded stone aggregate),as in sub base finished even and smooth without using extra cement.

M & L for factory made Coloured Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) conforming to IS 15658-2006 of 80 mm thick, M-40 Grade with grey cement and pigment laid over and including 50mm thick sand cushioning, complete all as specified and directed by Engr-in-charge.

M&L for PCC (1:2:4) ty B-1 using 20mm graded stone aggregate as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, copings, kneelers, apex stones, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed by Engr-in-charge.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/ loose soil.

Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:4) complete.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soil.

Removing excavated material exc. 50m but not exc 100m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified.

S & F precast cement concrete type B0 1:2:4 (12.5 mm graded aggregates) louvres and jallies, 45mm thick set in CM (1:4) (measured solid), including all mouldings but excluding frame (Pre cast frame shall be measured and paid seperately) including demolition of existing RCC Jallies complete all as specified and directed.

S&F Factory made Solid PVC Moulded Door Shutter 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, cast type anodised complete all as specified and as directed.

S&F 200mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

M & L for Preparation of newly plastered /unplastered surfaces of walls and ceilings and applying two coats of Oil Bound Distemper on wall surfaces over a coat of primer and 1.5-2mm thick wall care putty ,complete all as specified and directed.

S&F stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed.

M & L for brick work with sub-class B brick straight or curved on plan built in cement mortar 1 : 6 complete all as specified and directed

M&L for 100mm PCC type D -2 (1:4:8) using 40 mm graded crushed stone aggregate as in Sub base complete all as specified and directed.

S&F(plain or chequered ) channels ,square cut or notched ( oridinary and counter sunk) forming holes , w/o any attatchment.

M&L for mild steel bolts purpose made with hexagonal or square head one end each screwed other end to be fitted with washers and one hexagonal or square nut. Dia 16mm and 60 cm long.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in proof covering / cladding to wall, fixed with self tapping screws as specified.

M&L for two coat of Cement base paint over a coat of cement primer on new surface of wall complete.

M&L for Cement Concrete in CM 1:3:6 type C1 as in plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Providing and fixing factory made uPVC white colour fixed window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware , EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 6mm thick glazing with toughened glass with etching wk complete in differnnt colurs and desinged) After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality. (Note: The unit rate quoted by contractor including cost of toughened glass with etching work and includes all other connected accessories Net opening will be measured for payment purpose.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. comprising of uPVC multi?chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Note: The unit rate quoted by contractor includes cost of 5.5mm glass, Wiremesh and includes all other connected accessories. Net Opening will be measured for payment purpose) .

S&F 12 mm thick toughened frosted glass (with etching wk in different clour) door shutters of size area exc 1.50 Sqm but not exc 3 Sqm, including necessary floor spring hydraulically regulated, other side fixed on pivot CP fittings and fixtures, CP handles 400 mm long, CP locking arrangement, necessary cutting & holes moulding and fixed including engraving, emblem and lattering not exc 200 mm each complete as per directed by Engr-in-Charge.

S & F Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete as per directed by Engr-in-Charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets etc complete all as specified and as directed.

S & F plain gypsum board panel 12 mm thick on ceiling with and including necessary GI frame work for seamless ceiling used with ' T ' , channel or any section including screws , cleats ,fasteners, clips and all required accessories , hangers etc of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm etc (Any Design & pattern as approved by GE) complete all as specified and directed.

Taking down/ out carefully copper/aluminium point wiring for light/fan/bell/ sockets 5/15 Amps complete without accessories as switches, Sockets, holders, ceiling roses, light fitting regulators etc (to be measured and paid separately under relevent item of this Sch as S&F in repair and credit for these item given in credit schedule here-in-after) and making good the disturbed surface all as directed.

Material and labour of point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and fittings such as tees, bends, elbow, and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly including Metal Flush Box, Cover plate with frame, cutting chases and making good disturbed surface in CM 1:3 to match with existing surface for following:-

(a) one light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

(b) one socket outlet point 5 amps on the same board.

S&F in replacement Modular switch 6 Amp, 1 way, 1 module size complete all as directed.

S&F in replacement Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as directed.

S&F in replacement Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

S & F surface and wall mounted LED tube light fitting with Aluminium housing & interated electronic driver with tube rod of 20 Watt. slim elegant design.and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector all as specified and directed.

Supply and fix in replacement exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm complete.

S & F of MCB DB conforming to IP 43 - IK 09 with double door , SPN 8 way complete with din rail Neutral and earthing bar after taking out the old unserviceable DBs connection and making good the disturbed surfaces complete all as specified and as directed.

S&F in replacement of MCB SP, B Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

S&F in replacement of MCB SPN B Curve type, 10 KA, 63 Amp, with over load and short circuit protection complete all as directed.

M&L earthing with galvanised steel plate electrode 600 x 600 x 6 mm thick, buried directly in ground( earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level , connected to and including galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, washers of galvanised steel earth strip protected by and including 20 mm bore “light grade” and connected to main test point as directed and including concrete pit in PCC(1:3:6) type C1 precast RCC M-25 (design mix) precast cover slab (54 x 54 x 5 cm) duly reinforced with and including 8 mm dia TMT steel bars @ 150 mm C/C both way, one lifting handle made of 8 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI medium grade pipe for watering, charcoal and salt in alternate layers, including necessary excavation and earth work any type of soil complete all as specified and shown in electrical plate No. 5 of SSR Part –I including testing on completion complete all as specified and directed.

S&F of desert cooler of size > 25x25x36 inch, 4000 CuM/Hr, fabricated full body part with GI sheet of thickness 18 SWG, GI sheet having suitable door handle fitted with cooler, heavy duty fan motor kit in three speed mode (Low, Medium & High) having > 1400 RPM, fan blade of 18" size sweep (5 leaves), material of fan blade & hub should be metal type, honeycomb cooling pads, front grill with louvers also should be metal type, heavy type ISI marked submersible pump having output head 1m height, fan motor are made copper winding, GI wire mesh with pad set size 1x1" should be made of > 12 SWG, inside bottom tank and whole body should be painted with double coated red oxide paint of good quality and also written "AGE E/M BHDC" in capital letter of required size at cooler, tank capacity should be > 100 ltrs complete all as specified and directed by Engr-in-Charge. Pump & Motor Make: Crompton Greaves/ Khaitan/ Usha.

S&F fabricated MS stand of cooler size made out of MS angle iron frame of size 25 x 25 x 4 mm in cubical shape and MS flat iron strip of size 20 mm width and 3mm thickness to hold the legs of cooler stand at the bottom including welding and duly painted with two coat of synthetic enamel paint over a coat of red oxide primer complete.

S&F sub main wiring with 2 runs of 1.5 Sqmm FRLS single core PVC insulated & unsheathed cabl, 1100 Volts grade with multi stranded copper conductor drawn through and including suitable size of PVC casing and capping medium grade as per IS with all fittings and one run of 1.5 Sqmm FRLS PVC insulated copper conductor and complete all as specified and as directed. Note:- (Two run of cable along with earth conductor including PVC casing capping shall be measured as one RM length).

Supply and fixing of Modular switch 1 way 6 Amp complete

Supply and fixing of Modular socket 6A, 2/3 pin combined 2 module complete.

Supply and fixing of Modular cover plate with frame for 3 module complete

Supply and fixing of Modular Metal flush box for 3 module complete.

Supply and fixing Modular plug top of 6 Amps complete

Akhil Enterprises (BID ID -3375973)

R R Associates (BID ID -3374818)

M/S Rohit Enterprises (BID ID -3376273)

sony engineering works (BID ID -3375379)