Additional Estimate for Annexe I Building with Ancillary Works and Additional outside work of New Assam Legislative Assembly Complex at Dispur as per Revised Design Proposal

Amount

CIVIL EXTRA ITEMS Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) : 400 mm dia piles

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. 4th Floor-7th floor

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. 8th Floor-11th floor

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. 12th Floor-Terrace floor

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means. 9th Floor-12th floor

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means. 13th Floor-Terrace floor

Providing and fixing 12 mm thick frameless toughened glass partitions of approved brand and manufacturer, including providing and fixing partitions at top & bottom with aluminum channel etc. all complete as per direction of Engineer-in-charge

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks)

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and fixing 15mm thick Engineer wooden flooring with approved pattern, design, shade of approved make of ‘ KAHRS’ or approved equivalent make confirming to European Standards. Moisture Content as per EN13183 7%+-2%, Breaking Strength N/mm2 as per EN1533 NPD, Thermal Conductivity R value- as Per EN12664 0/14W/Mk, Biological Durability as Per EN350-2 Class1, And Top layer of plank shall be made of minimum 3mm natural Veneer of any shade. Surface of Top layer shall be pre finished with oiled immediately after installation if not prefinished, which shall be free from urea Formaldehyde and solvents. Flooring plank shall be woodloc@ 5S in a glue less floating manner or can be glued down as well . Engineered wood planks shall be a composition of 3 layer of Pine/Spruce lamella wood with direction of each layer oriented at right angle to the adjacent layer of natural strain in Lacquer and Non-Beveled/ Beveled in length and width as specified. Wooden flooring shall be FSC (Forest Stewardship Council) & Green Guard Certified. With certifications of SUNDAHUS, RTS M-1, BASTA, FLOOR SCORE , CE -The floor shall be laid in place with matching original profiles and accessories as approved and as per recommendations of approved manufacturer over base of existing flooring. Rate shall be inclusive of making any cut-out for services, floor matching cover over cut outs etc. complete. The contractor shall get approval of sample before execution etc. all complete as per manufacture’s specification and as directed by the Engineer-in-Charge.

Providing and fixing 40mm thick cladding comprising of Wooden framework using 25mx50mm sections at a maximum spacing of 600mm in any one direction (including adding members as required) covered with12mm thick BWP ply layered with 4mm thk. veneer on one side pasted and pressed with adhesive to give a uniform and smooth finish, including 4mm thk. S.S. strip framework on all sides of veneer panels with wooden member surround, top moldings / margins etc. to finish the thickness, as shown complete in drawing. All members / ply etc. shall be treated with anti-termite solution as per norms. No extra shall be paid for making of openings, door / window frames and for making provisions for electric conduits.

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) On one side only

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and applying of Heritage Granules, a surface texture paint after applying corresponding roller coat brush finish as heritage primer on pre plasterd surface to be smooth level without any undulations,color scheme as per approved sample in approved shade.Granules is a two component system of Dry Granules 25 kg and 5 kg of Bonding agent.The composition of texture paint consits of Acrayallic copolymer emulsion combined with 92 % natural Sillica sand, inorganic pigments,bacteriside,fungicidesand various other additives giving the product water repellant properties. The first coat (primer )should be applied by brush or wool roller as base coat, diluted with sufficient water and the next coat a final coat to be applied with trowel and properly finished. The thickness of both coat should be 0 .80 mm to 1.20 mm.Application to be carried out by company 's Authorised Dealer.

Providing and laying Bitumen Penetration Macadam with hard stone aggregate of quality, size and grading as specified, with bitumen of suitable penetration grade, including required key aggregate as specified, spreading coarse aggregate with the help of self propelled/tipper tail mounted aggregate spreader and applying bitumen by a pressure distributor and then spreading key aggregate with the help of aggregate spreader complete, including consolidation with road roller of minimum 8 to 10 tonne capacity to achieve specified values of compaction and surface accuracy : For 50mm compacted thickness using coarse aggregate of size 50-20 mm graded @ 0.60 cum per 10 sqm key aggregate of size 12.5 mm graded @ 0.15 cum per 10 sqm. With paving asphalt grade VG - 10 @ 50 kg/ 10 sqm.

Providing and laying seal coat over prepared surface of road with bitumen heated in bitumen boiler fitted with the spray set spraying using 98 kg of bitumen of grade VG - 10 and blinding surface with 0.90 cum of stone aggregate of 6.7 mm size (Passing 11.2 mm sieve and retained on 2.36 mm sieve) per 100 sqm of road surface, including rolling and finishing with power road roller all complete. Note: Seal coat items to be operated only with the prior approval of chief Engineer concerned.

Providing and displaying of Raphis palm having ht. 75 cm to 90 cm with 12 to 15 equal suckers, well developed, full of fresh & healthy leaves from bottom to top in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum inerme of ht. 20 cm to 30 cm multi branched in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Heliconia psittacorum

Cordyline fruticosa

Hymenocallis littoralis (spider lilly)

Pandanus baptisiti

Tradescantia spathacea (rhoeo discolour)

Sansevieria Trifasciata (laurenti)

Providing and Displaying Euphorbia milli hybrid variety with multi branch, full bloom, with fresh and healthy well developed having 30 to 45 cm ht. in 35 cm Cement Pots as per direction of the officer-in-charge.

Providing and stacking of Asparagus sprengeri of height 15 cm to 20 cm, full of leafy branches in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Sansevieria Trifasciata (laurenti) dwarf

Agathis robusta

Providing and stacking of Largerstroemia indica of height 90-105 cm. multibranched in poly bags of size 25 cm as per direction of the officer-in-charge.

Artocarpus altilis (Breadfruit tree)

Phenix canariensis (Canary Island date palm)

Agave desmettiana

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and laying in position ready mixed or site batched design mix concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering , finishing and reinforcement as per direction of the engineer-in-charge for the following grade of concrete. Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M25 grade with minimum cement content of 330 kg/cum

Providing and laying in position ready mixed or site batched design mix concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering , finishing and reinforcement as per direction of the engineer-in-charge for the following grade of concrete. Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M30 grade with minimum cement content of 350 kg/cum

Providing and laying in position ready mixed or site batched design mix concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering , finishing and reinforcement as per direction of the engineer-in-charge for the following grade of concrete. Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level : Concrete of M25 grade with minimum cement content of 330 kg/cum

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with 115 thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar.The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means. 5th Floor- 8th Floor

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade : Area of Slab over 0.50sqm

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 10 to 13 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.13 to 16 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 16 to 19 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 19 to 22 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 22 to 25 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 25 to 28 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 28 to 31 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 31 to 34 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 34 to 37 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 37 to 40 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 40 to 43 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 43 to 46 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 46 to 49 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 49 to 52 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 52 to 55 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 55 to 58 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 58 to 61 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 61 to 64 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 64 to 67 m

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 67 to 70 m

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, ptimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin- charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and fixing 18mm thick Granite stone work for wall lining upto 10 m height in cement mortar 1:3 (1cement : 3 coarse sand) including pointing with white cement mortor with an admixture of pigment to match the granite shade complete as per direction of Engineer-in-charge.

Providing & fixing 150mm wide Chicken wire mesh on joints of RCC & Brick work before plastering complete in the direction of Engineer-in-charge.

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. 5th Floor-8th floor

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. 9th Floor-12th floor

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. 13th Floor-Terrace floor

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means. 9th Floor-12th floor

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means. 13th Floor-Terrace floor

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to alead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars

Dismantling old plaster or skirting raking out joints and cleaning the surface for plasterincluding disposal of rubbish to thedumping ground within 50 metres lead

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Tile Size -800x800 mm

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joiningwith cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approvedand removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety featuresfor the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. sqm 338.25 Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Providing, placing and fixing in position Chemical rebar fastners (of M/s Hilti or M/s Sika or approved equivalent conforming to Europian standard CSTB/ETA and Civil Aid standard) of vaious diameters in Piers, Pier caps, including drilling holes of specified size and depth, cleaning holes, placing chemicals inside the holes and fixing reinforcing bars as per specifications of the chemical rebar supplier, and under supervision of the authorized representative of the supplier and conducting pull-out test of atleast 5% of total nos. of chemical re-ba fastners (cost of reinforcing bars to be paid seperately) all complete as per specification as directed byb the department a) 12 mm dia re-bar fastners

Providing, placing and fixing in position Chemical rebar fastners (of M/s Hilti or M/s Sika or approved equivalent conforming to Europian standard CSTB/ETA and Civil Aid standard) of vaious diameters in Piers, Pier caps, including drilling holes of specified size and depth, cleaning holes, placing chemicals inside the holes and fixing reinforcing bars as per specifications of the chemical rebar supplier, and under supervision of the authorized representative of the supplier and conducting pull-out test of atleast 5% of total nos. of chemical re-ba fastners (cost of reinforcing bars to be paid seperately) all complete as per specification as directed byb the department d) 25 mm dia re-bar fastners.

Makiing of Hole 3" with core Cutter

Makiing of Hole 5" with core Cutter

Supplying and installation of moisture resistant/fire resistant cement board as per standard sizes fixed with self-drilling / taping screws. Screws shall be of counter sunk rib head of 1.60 mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. Cement Fiber Board 6 mm thick as per IS 14862:2000 of type B (High pressure Steam Cured)

FURNITURE WORK Providing & Placing HON' SPEAKER'S ROOM Cabin Table with side unit with following details and specification :- whose top is made of 50-55mm thick E1 grade MDF (Environmental Friendly) with 0.4mm thick Veneer Finish, With Key board tray & Leatherite pad on the main table , size of leatherite is 900-1200Wx 460-560Dmm , with edge banding. E1 grade MDF with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Closed wiring tray is made of steel sheet thickness 1.2mm. Epoxy powder coated spray color, baked at temperature 200 C°. Below the acess flap/ axial box ( 2-3 nos socket/Switch), Top supported on one side suspended combo storage & One side Three drawer unit of size: 560Wx 670Dx 680Hmm with Dummy Box which is fixed with modesty panel, Drawer & Modesty are made of 19mm thick E1 grade MDF Board (Environmental Friendly) with 0.4mm thick Veneer Finish, Drawer unit & side combo storage connecting with 19mm thick MDF modesty panel with matching finish cover Edge banding (PVC) . E1 grade Veneer MDF with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Side Combo Storage: Body of storages made out 19 mm thick (E1 Grade) MDF board with 0.4 mm veneer with PVC edge-banding. Side Combo Storage is combination of 2nos swing shutter & Open space, E1 grade MDF to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992).The storage should have extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Low height back storage: Body of storages made out 19 mm thick (E1 Grade) MDF board with 0.4mm veneer with PVC edge- banding. shutter madeout of E1 grade MDF to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in- house quality . All shelf are adjutable. This should comply with (EN 120-1992).The storage should have extruded aluminum handle/ recess handle , as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. HON' SPEAKER'S ROOM Office Cabin Table is of Size: 3000mm(L1) x 2400mm(L2) x 1200mm(D1) x 550-600mm(D2)x 740- 760mm(H1)/580-600mm(H2).

Providing & Placing HON' SPEAKER'S ROOM Cabin Table with side unit with following details and specification :- whose top is made of 50-55mm thick E1 grade MDF (Environmental Friendly) with 0.4mm thick Veneer Finish, With Key board tray & Leatherite pad on the main table , size of leatherite is 900-1200Wx 460-560Dmm , with edge banding. E1 grade MDF with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Closed wiring tray is made of steel sheet thickness 1.2mm. Epoxy powder coated spray color, baked at temperature 200 C°. Below the acess flap/ axial box ( 2-3 nos socket/Switch), Top supported on one side suspended combo storage & One side Three drawer unit of size: 560Wx 670Dx 680Hmm with Dummy Box which is fixed with modesty panel, Drawer & Modesty are made of 19mm thick E1 grade MDF Board (Environmental Friendly) with 0.4mm thick Veneer Finish, Drawer unit & side combo storage connecting with 19mm thick MDF modesty panel with matching finish cover Edge banding (PVC) . E1 grade Veneer MDF with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Side Combo Storage: Body of storages made out 19 mm thick (E1 Grade) MDF board with 0.4 mm veneer with PVC edge-banding. Side Combo Storage is combination of 2nos swing shutter & Open space, E1 grade MDF to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992).The storage should have extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Low height back storage: Body of storages made out 19 mm thick (E1 Grade) MDF board with 0.4mm veneer with PVC edge- banding. shutter madeout of E1 grade MDF to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in- house quality . All shelf are adjutable. This should comply with (EN 120-1992).The storage should have extruded aluminum handle/ recess handle , as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. HON' SPEAKER'S ROOM Office Cabin Back Storage of size: 2450Wx 400D x 1800Hmm

Providing & Placing LEADER OF OPPOSITION/PRINCIPAL SECRETARY'S/DEPUTY SPEAKER'S Cabin Table with side unit with following details and specification :- whose top is made of 45-55mm thick E1 grade MDF (Environmental Friendly) with Veneer Finish, with edge banding. E1 grade MDF with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board- perforated method) for better in-house quality. This should comply with (EN 120-1992). The Closed wiring tray is made of steel sheet thickness 1.2mm. Epoxy powder coated spray color, baked at temperature 200 C°. Below the acess flap/ axial box ( 2-3 nos socket/Switch), Top supported on one side suspended combo storage & One side Three drawer unit of size: 560Wx 670Dx 680Hmm with Dummy Box which is fixed with modesty panel, Drawer & Modesty are made of 19mm thick E1 grade MDF Board (Environmental Friendly) with Veneer Finish, Drawer unit & side combo storage connecting with 19mm thick MDF modesty panel with matching finish cover Edge banding (PVC) . E1 grade Veneer MDF with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Side Combo Storage: Body of storages made out 19 mm thick (E1 Grade) MDF board with veneer Finish with PVC edge-banding. Side Combo Storage is combination of 2nos swing shutter & Open space, E1 grade MDF to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992).The storage should have extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. LEADER OF OPPOSITION/PRINCIPAL SECRETARY'S/DEPUTY SPEAKER'S Cabin Table is of Size: 3000mm(L1) x 2300mm(L2) x 900-1000mm(D1) x 650mm(D2)x 740-760mm(H1)

Providing & Placing Director Cabin Table with side unit with following details and specification :- Providing and placing table Whose top and legs are made of 38mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 16 mm cover with Melamine Edge-Banding(PVC) 2 mm. Also legs are made of Particle board wood Grade E-1 (Environmental Friendly) thicness 25 mm, cover with Melamine. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Low Height Swing Door Storage, Body of storages made out 18 mm thick Particle Board (E-1 Grade), melamine finishes with 2 mm PVC edge-banding. E1 grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Front of Low height Storages should be made out of 16 mm thick Particle Board (E-1 Grade),melamine finishes with 2 mm. PVC edge-banding fitted with extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Director Cabin Table of Size: 2000mm(L1)x1950mm(L2)x 900mm(D1) x 500-550 mm(D2)x 740-760mm(H1)/620- 640mm(H2).

Providing & Placing Director Cabin Table with side unit with following details and specification :- Providing and placing table Whose top and legs are made of 38mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 16 mm cover with Melamine Edge-Banding(PVC) 2 mm. Also legs are made of Particle board wood Grade E-1 (Environmental Friendly) thicness 25 mm, cover with Melamine. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Low Height Swing Door Storage, Body of storages made out 18 mm thick Particle Board (E-1 Grade), melamine finishes with 2 mm PVC edge-banding. E1 grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Front of Low height Storages should be made out of 16 mm thick Particle Board (E-1 Grade),melamine finishes with 2 mm. PVC edge-banding fitted with extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Director Cabin Cabin Back Storage of size:2000Wx 450D x 740-760mm(H).

Providing and placing of Deputy/Under Secretary/ Estate Officer Cabins Tables with following details and specification : - Providing and placing table Whose top and legs are made of 38mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 25 mm cover with Melamine Edge-Banding(PVC) 2 mm. Also legs are made of Particle board wood Grade E-1 (Environmental Friendly) thicness 38 mm, cover with Melamine. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600- 620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Low Height Swing Door Storage, Body of storages made out 18 mm thick Particle Board (E-1 Grade), melamine finishes with 2 mm PVC edge-banding. E1 grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Front of Low height Storages should be made out of 16 mm thick Particle Board (E-1 Grade),melamine finishes with 2 mm. PVC edge-banding fitted with extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Deputy/Under Secretary/ Estate Officer Cabin Tables of size :MainTable 1800W x900D x 740-760Hmm, Return Table :1050W x 500D x740-760Hmm

Providing and placing of Deputy/Under Secretary/ Estate Officer Cabins Tables with following details and specification : - Providing and placing table Whose top and legs are made of 38mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 25 mm cover with Melamine Edge-Banding(PVC) 2 mm. Also legs are made of Particle board wood Grade E-1 (Environmental Friendly) thicness 38 mm, cover with Melamine. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600- 620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Low Height Swing Door Storage, Body of storages made out 18 mm thick Particle Board (E-1 Grade), melamine finishes with 2 mm PVC edge-banding. E1 grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Front of Low height Storages should be made out of 16 mm thick Particle Board (E-1 Grade),melamine finishes with 2 mm. PVC edge-banding fitted with extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Deputy/Under Secretary/ Estate Officer Cabins Back Storage of size: 1800W x 450D x 740-760Hmm

Providing and placing Office Cabin Whose top and legs are made of 25mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 18 mm cover with Melamine Edge- Banding(PVC) 2 mm. Also legs are made of Particle board wood Grade E-1 (Environmental Friendly) thicness 25 mm, cover with Melamine. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Low Height Swing Door Storage, Body of storages made out 18 mm thick Particle Board (E-1 Grade), melamine finishes with 2 mm PVC edge-banding. E1 grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board- perforated method) for better in-house quality. This should comply with (EN 120-1992). Front of Low height Storages should be made out of 16 mm thick Particle Board (E-1 Grade),melamine finishes with 2 mm. PVC edge-banding fitted with extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Superintendent/ Committee Officer Cabin Table Main Table 1650W x 750D x 740Hmm, Return Table :900W x 450D x740- 760Hmm

Providing and placing Office Cabin Whose top and legs are made of 25mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 18 mm cover with Melamine Edge- Banding(PVC) 2 mm. Also legs are made of Particle board wood Grade E-1 (Environmental Friendly) thicness 25 mm, cover with Melamine. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Low Height Swing Door Storage, Body of storages made out 18 mm thick Particle Board (E-1 Grade), melamine finishes with 2 mm PVC edge-banding. E1 grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board- perforated method) for better in-house quality. This should comply with (EN 120-1992). Front of Low height Storages should be made out of 16 mm thick Particle Board (E-1 Grade),melamine finishes with 2 mm. PVC edge-banding fitted with extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Office Cabin Back Storage of size: 1650W x 450D x 740-760Hmm

Providing and placing Office Cabin Whose top and legs are made of 25mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 18 mm cover with Melamine Edge- Banding(PVC) 2 mm. Also legs are made of Particle board wood Grade E-1 (Environmental Friendly) thicness 25 mm, cover with Melamine. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Low Height Swing Door Storage, Body of storages made out 18 mm thick Particle Board (E-1 Grade), melamine finishes with 2 mm PVC edge-banding. E1 grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board- perforated method) for better in-house quality. This should comply with (EN 120-1992). Front of Low height Storages should be made out of 16 mm thick Particle Board (E-1 Grade),melamine finishes with 2 mm. PVC edge-banding fitted with extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Free Standing Table 1500W x 750D x 740Hmm,

Providing and placing Hybrid Panel based Workstations with following specifications:Frame Work, Partition and Cable management : Frame work shall consist of main spine and return spine of aluminium extruded section of minimum thickness of 1.2 mm. The overall thinkness of Panel base System should be minimum 60-70 mm. The thickness of main spine partition panel should be minimum 60-70 mm & Return spine partition panel should be minimum 25-30 mm The panel will be hollow inside to accommodate wiring for electrical/data and outer frame of panel should be made of extruded aluminium.The panel shall be made up of 3 mm thick MDF both sides of the wooden frame to create the hollow for the wire management. The panel outer aluminium frame is designed in such a way that it can be easily slide in to the columns/ Connectors by means of stacking one over the other. Horizontal race way should be 150-170 mm height aluminium profile. There shall be complete cable management arrangement with openable raceway above/ below worktop with provision for fitting electrical/data switches and holes for passing cable.Panel Finishes : Finishes of panel above the worktop can be fabric pinup/fabric/laminate + Glass/metal writable marker board or single finish tile with raceway on main spine. Finishes of main spine panel below the worktop the hollow panel should be made of MDF tile and 0.5mm thick steel sheet pasted on MDF which is powder coated with EPC finish 80-90 microns for durability on the inside as well on the outside. Raceway can be provided above/below the worktop.Connectors/ Brackets: End Post: Aluminium 60-70 mm width – 1180-1220mm Heightt.Two way post: Aluminium 30-70 mm width –1180-1220mm Height.Three way post: Aluminium 30-70 mm width –1180-1220mm Height Four way post: Aluminium 30-70 mm width – 1180-1220mm Height Brackets: Table top supported with 50-60mm width steel bracket. Table top to table top connector: 150-170 mm Width x 120-140 mm Depth width connector. Rect Workstation of size:- 1200mm (W) x 600mm (D) x 740mm(Worktop Height) x 1180-1220mm

Providing and placing Hybrid Panel based Workstations with following specifications:Frame Work, Partition and Cable management : Frame work shall consist of main spine and return spine of aluminium extruded section of minimum thickness of 1.2 mm. The overall thinkness of Panel base System should be minimum 60-70 mm. The thickness of main spine partition panel should be minimum 60-70 mm & Return spine partition panel should be minimum 25-30 mm The panel will be hollow inside to accommodate wiring for electrical/data and outer frame of panel should be made of extruded aluminium.The panel shall be made up of 3 mm thick MDF both sides of the wooden frame to create the hollow for the wire management. The panel outer aluminium frame is designed in such a way that it can be easily slide in to the columns/ Connectors by means of stacking one over the other. Horizontal race way should be 150-170 mm height aluminium profile. There shall be complete cable management arrangement with openable raceway above/ below worktop with provision for fitting electrical/data switches and holes for passing cable.Panel Finishes : Finishes of panel above the worktop can be fabric pinup/fabric/laminate + Glass/metal writable marker board or single finish tile with raceway on main spine. Finishes of main spine panel below the worktop the hollow panel should be made of MDF tile and 0.5mm thick steel sheet pasted on MDF which is powder coated with EPC finish 80-90 microns for durability on the inside as well on the outside. Raceway can be provided above/below the worktop.Connectors/ Brackets: End Post: Aluminium 60-70 mm width – 1180-1220mm Heightt.Two way post: Aluminium 30-70 mm width –1180-1220mm Height.Three way post: Aluminium 30-70 mm width –1180-1220mm Height Four way post: Aluminium 30-70 mm width – 1180-1220mm Height Brackets: Table top supported with 50-60mm width steel bracket. Table top to table top connector: 150-170 mm Width x 120-140 mm Depth width connector. TL Workststion: 1500Wx 750Dx x 740H, Side Table : 750 Wx 450Dx (Worktop Height) x 1180-1220mm

Providing and placing Meeting/ Discussion tables :Worktop shall be made out of 25mm thick E-1 grade (Environmental Friendly) particle board cover with laminate and all the edges of worktop shall be provided with machine pressed 1.5-2 mm thick ABS edge banding glued with hot melt EVA glue. E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The height of Worktop shall be 750 mm from ground level. Understructure: MS understructure with 50mm x 50mm C type square Straight leg, well supported with MS beams under table top to supported top & connected to leg to leg. Wire management: Access Flap and Switch Mounting Tray is provided in the table. It is Made from Matt silver Anodized Aluminium extrusion and plastic moulded components to facilitate access of Electrical/Data/Voice sockets access from Top. Powder coated switch mounting tray made from 0.8mm and 1.2mm MS sheet(IS:513) which is powder coated 80-90micron. Switches to be mounted on tray as per requirement. Provision for mounting 8Module Switch plate on switch mounting tray shall be provided. The product should be complete and as per approved sample and as per the direction of Engineer-In- charge.Completely conseled wiremanagement with vertical wire uptake from floor via middle leg/ Power pole having removable cover one side and wire seperator for data and wire seperation, segregates to hozizontal cable tray below Access Flap.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. 8 Pax Rect Shape Meeting Table : 3000W x 1050D x 740Hmm

Providing & Placing of Conference Table, whose top and legs are made of 38 mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mm PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 18 mm cover with Melamine Edge-Banding(PVC) 2 mm. Wire management: Access Flap and Switch Mounting Tray is provided in the table. It is Made from Matt silver Anodized Aluminium extrusion and plastic moulded components to facilitate access of Electrical/Data/Voice sockets access from Top. Powder coated switch mounting tray made from 0.8mm and 1.2mm MS sheet(IS:513) which is powder coated 80-90micron. Switches to be mounted on tray as per requirement. Provision for mounting 8Module Switch plate on switch mounting tray shall be provided. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. 15Pax Confernce Table: 5100W1 x 1600D x 740-760Hmm

Providing & Placing of Conference Table, whose top and legs are made of 38 mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mm PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 18 mm cover with Melamine Edge-Banding(PVC) 2 mm. Wire management: Access Flap and Switch Mounting Tray is provided in the table. It is Made from Matt silver Anodized Aluminium extrusion and plastic moulded components to facilitate access of Electrical/Data/Voice sockets access from Top. Powder coated switch mounting tray made from 0.8mm and 1.2mm MS sheet(IS:513) which is powder coated 80-90micron. Switches to be mounted on tray as per requirement. Provision for mounting 8Module Switch plate on switch mounting tray shall be provided. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. 27 Pax U Shape Confernce Table:8800W1 x 1600D x 740-760Hmm

Providing and placing in position medium back revolving Chair , Overall Chair size: 440-460W x 440-460Dx 750Hmm , BACKREST: The outer frame of the backrest made of injection moulded in black 20% Glass Filled Polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has fix lumber support for achieving comfortable seating posture.BACK SIZE :440Wx 390Hmm, SEAT: The seat is made up of 12 mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the plywood, Seat Size: 450Wx 440D x 420Hmm.SEAT FOAM:Foam made out of moulded polyurethane foam with the following properties. Average thickness of 65 mm (Depth- 450 mm) and with the following properties: Handle To Handle(Inside) – 470 mm Handle To Handle(Outside) – 570 mm, Armrests: Integrated adjustable armrest made of PP. The armrest shall be scratch resistant with suitable padding and tablet of size (should be as per manufacturer specification). Tablet (Flap) to be provided made of PP to be finished as desired with foldable mechanism on the right hand side as shown in the indicative image. The tablet should have the inbulit feature of cup holder . Frame: The Chair to be provided with Powder coated MS tubular frame & made of 27-32mm X 15mm- 20mm thick fitted with 4 nos. twin wheel csators . The above chair should be finished / completed as per above mentioned specifications including providing and fixing of other related materials including hardwares, etc, with suitable levellers, complete or as directed by the Engineer-in- Charge.CASTORS:50 mm: The castors are injection moulded 20% Glass Filled Polypropylene and diameter of castor is 50 mm. The castors are tested for 100000 cycles and will comply as per ANSI/BIFMA X 5.1 standards.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 Years warranty.

Manufacturing, providing and Placing High Back revolving chairs for HON' SPEAKER'S ROOM Cabin Main Chair of make M/s Rockworth (as per finally approved sample by department) of following dimensions with the following specifications. Providing and placing High Back chairs. The seat, backrest & arm shall be made up of 12mm thick hot pressed plywood & upholstered with leatheritte and moulded medium density foam. Overall dimensions of Chair shall be, Width of Chair - 650- 670 mm, Depth of Chair - 665-685mm, Height of Chair-1170-1230mm as measured till pedestal . The back shall be designed with contoured lumber support for extra comfort. Medium density foam should be used in making seat & back which shall be moulded with density 45kg/m ³ and hardness load 16kgf. The seat and back should be arrested together with spine . The fixed armrest . The mechanism of the chair shall have following features: STG mechanism, 360 degree swivel type, Knee Tilt mechanism, Seat & back tilting ration of 1: 1.5, Front pivot for tilt with feet resting on ground ensuring more comfort, multiple locking position. Gas lift allows 10mm of height adjustment. The pedestal shall be made of die-cast aluminium base. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 670mm pitch-centre-dia 700-720mm with castors). The twin wheel castors shall be made of Nylon injection moulded in black color. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality.

Manufacturing, providing and Placing Mid Back revolving chairs for HON' SPEAKER'S ROOM Cabin Mid back visitor Chair of make M/s Rockworth (as per finally approved sample by department) of following dimensions with the Providing and placing High Back chairs. The seat, backrest & arm shall be made up of 12mm thick hot pressed plywood & upholstered with leatheritte and moulded medium density foam. Overall dimensions of Chair shall be, Width of Chair - 640- 660 mm, Depth of Chair - 645-665mm, Height of Chair-1010-1070mm as measured till pedestal . The back shall be designed with contoured lumber support for extra comfort. Medium density foam should be used in making seat & back which shall be moulded with density 45kg/m ³ and hardness load 16kgf. The seat and back should be arrested together with spine . The fixed armrest . The mechanism of the chair shall have following features: STG mechanism, 360 degree swivel type, Knee Tilt mechanism, Seat & back tilting ration of 1: 1.5, Front pivot for tilt with feet resting on ground ensuring more comfort, multiple locking position. Gas lift allows 10mm of height adjustment. The pedestal shall be made of die-cast aluminium base. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 670mm pitch-centre-dia 700-720mm with castors). The twin wheel castors shall be made of Nylon injection moulded in black color. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality.

Providing and placing in position High back chair with headrest, Overall chair size: 680Wx 660Dx 1150-1220Hmm, Chair should be high back, cushioned seat assembly, moulded plywood upholstered with moulded polyurethane foam & finished with Leatherite. Back size: (W) 520 - 540 mm (H) 660-680mm; Seat size: (L) 520mm - 540mm (W) 490 - 510mm with Polyurethane Foam. Polyurethane Foam: The polyurethane foam (Recyclable) of minimum density = 30 kg/ cum + 2 kg/cum fixed to moulded plywood and upholstered with Leathritte. Fixed armrest of premium quality of SS Chromed finish with PU cushion pads. Synchro mechanism: 360 degree revolving type, from pivot for tilt with multiple locking position & feet resting on ground for extra comfort. The pneumatic adjustment has an adjustment stroke of 70-120 mm, Pedestal Assembly: should have 5 star aluminium die cast with hard castors sutable for tiles flooring with adjustment, twin wheel castors & the pitch centre Dia is 650 +/- 50mm. (750 +/- 10mm with castors). Twin wheel castors: these are made of injection moulded in black PP having 50-60mm dia,complete in all respect. The above chair should be finished / completed as per above mentioned specifications including providing and fixing of other related materials including hardwares, etc. complete or as directed by the Engineer-in-Charge and conforming to the image having back curvature in longitudinal and in trasverse direction as per the image. All complete as per manufacturers specification. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality.

Manufacturing, providing and Placing Mid Back revolving chairs for LEADER OF OPPOSITION/PRINCIPAL SECRETARY'S/DEPUTY SPEAKER'S Cabin Mid back visitor Chair of make M/s Rockworth (as per finally approved sample by department) of following dimensions with the following specifications. Providing and placing in position Medium back Chair, Overall chair size: 680Wx 660Dx 980-1040Hmm, Chair should be high back, cushioned seat assembly, moulded plywood upholstered with moulded polyurethane foam & finished with Leatherite. Back size: (W) 520 - 540 mm (H) 490-540mm; Seat size: (L) 520mm - 540mm (W) 490 - 510mm with Polyurethane Foam. Polyurethane Foam: The polyurethane foam (Recyclable) of minimum density = 30 kg/ cum + 2 kg/cum fixed to moulded plywood and upholstered with Leathritte. Fixed armrest of premium quality of SS Chromed finish with PU cushion pads. Synchro mechanism: 360 degree revolving type, from pivot for tilt with multiple locking position & feet resting on ground for extra comfort. The pneumatic adjustment has an adjustment stroke of 70-120 mm, Pedestal Assembly: should have 5 star aluminium die cast with hard castors sutable for tiles flooring with adjustment, twin wheel castors & the pitch centre Dia is 650 +/- 50mm. (750 +/- 10mm with castors). Twin wheel castors: these are made of injection moulded in black PP having 50- 60mm dia,complete in all respect. The above chair should be finished / completed as per above mentioned specifications including providing and fixing of other related materials including hardwares, etc. complete or as directed by the Engineer-in- Charge and conforming to the image having back curvature in longitudinal and in trasverse direction as per the image. All complete as per manufacturers specification. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality.

Manufacturing, providing and Placing High Back revolving chairs for Confernce Room/ Director Cabin Main Chair of make M/s Rockworth (as per finally approved sample by department) of following dimensions with the following specifications. Providing and placing in position high back Revolving Chair with seat made up of insert moulded Polyurethane Foam upholstered Leathirte with curved seat in order to provide extra support and blood circulation. Insert moulded foam assembled over a load bearing HPL seat cover, Back is made of is made up of one piece injection moulded frame, inner frame upholstered with korean mesh and mounted on the main assembly. Armrests should be fixed with leathrite padded fixed over integrated aluminium support armrest. Base of chairs should be made of Aluminium Alloy with nylon castor. Chair should be of 360 degree swivel Posture Control with multi pointer locking and synchro tilt mechanism which allows three levels of adjustment. Overall size of Chair shall be - 680-730mm W x 680-730mm D x 1090-1180mm H. Seat size 400- 450 mm depth, Seat width of 500-540 mm Seat Height of 450-550mm with hydraulic height adjustability of 90-100mm. Effective back height from Seat - 570mm, polyurethane foam. Pedestal made of aluminium alloy fitted with 5 nos. twin wheel castors (castor wheel dia. 60-70 cm), base pedestal dia 60-70 mm and pitch center dia. 700-720mm with castors, twin wheel castors injection moulded in Nylon etc. all complete as per manufacturers specification, approved sample and direction of Engineer-in-Charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality.

Manufacturing, providing and Placing Mid Back revolving chairs for Confernce Room/ Director Cabin Visitor Chair of make M/s Rockworth (as per finally approved sample by department) of following dimensions with the following specifications. Providing and placing in position medium back Revolving Chair with seat made up of insert moulded Polyurethane Foam upholstered Leathirte with curved seat in order to provide extra support and blood circulation. Insert moulded foam assembled over a load bearing HPL seat cover, Back is made of is made up of one piece injection moulded frame, inner frame upholstered with korean mesh and mounted on the main assembly. Armrests should be fixed with leathrite padded fixed over integrated aluminium support armrest. Base of chairs should be made of Aluminium Alloy with nylon castor. Chair should be of 360 degree swivel Posture Control with multi pointer locking and synchro tilt mechanism which allows three levels of adjustment. Overall size of Chair shall be - 680-730mm W x 680-730mm D x 950-1050mm H. Seat size 400- 450 mm depth, Seat width of 500-540 mm Seat Height of 450-550mm with hydraulic height adjustability of 90-100mm. Effective back height from Seat - 570mm, polyurethane foam. Pedestal made of aluminium alloy fitted with 5 nos. twin wheel castors (castor wheel dia. 60-70 cm), base pedestal dia 60-70 mm and pitch center dia. 700-720mm with castors, twin wheel castors injection moulded in Nylon etc. all complete as per manufacturers specification, approved sample and direction of Engineer-in-Charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality.

Manufacturing, providing and Placing High Back revolving chairs for Faculty /Office Cabin Main Chair of make M/s Rockworth- Crown Chair HB (as per finally approved sample by department) of following dimensions with the following specifications. Providing and placing High Back chairs Faculty/ Office Cabin. Chair Overall size: 680Wx 680Dx 1125-1215Hmm, Chair seat made up of insert moulded Polyurethane Foam upholstered with foam laminated mesh fabric, insert moulded foam assembled over a load bearing plastic seat cover, back is made up of two piece injection moulded frame, inner frame upholstered with mesh fabric and mounted on the main assembly, back adjustable lumbar support for achieving comfortable seating posture, seat size 450- 470 mm depth (approx.), 490-500 mm width (approx.), sub assembly back size 465-500mmW x 660- 690height. (approx.), effective back height from Seat - 550-570 mm (approx.), polyurethane foam for seat having density 65±4 kg/m3, armrest top injection moulded in polyurethane and mounted on the injection moulded height adjustable type armrest, armrest height adjustable up to 45mm (approx) in 3 steps & width movement adjustable, 360 degree revolving type. mechanism, single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position locking with antishock feature, pneumatic height adjustment of 85mm spine bracket made of aluminum die cast piece connecting to back with mechanism, pedestal made of die cast alunimium fitted with 5 nos. twin wheel castors (castor wheel dia. 60mm approx.), base pedestal dia 650mm (approx.) and pitch center dia. 700mm with castors, twin wheel castors injection moulded in Nylon etc. all complete as per manufacturers specification, approved sample and direction of Engineer-in-Charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Manufacturing, providing and Placing Mid Back revolving Visitor chairs forFaculty /Office of make M/s Rockworth - Crown MB (as per finally approved sample by department) of following dimensions with the following specifications. Providing and placing Mid Back chairs forFaculty /Office Cabin. Chair Overall size: 680Wx 680Dx 960-1050Hmm, , Chair seat made up of insert moulded Polyurethane Foam upholstered with foam laminated mesh fabric, insert moulded foam assembled over a load bearing plastic seat cover, back is made up of two piece injection moulded frame, inner frame upholstered with mesh fabric and mounted on the main assembly, back adjustable lumbar support for achieving comfortable seating posture, seat size 450- 470 mm depth (approx.), 490-500 mm width (approx.), sub assembly back size 465-500mmW x 660- 690height. (approx.), effective back height from Seat - 550-570 mm (approx.), polyurethane foam for seat having density 65±4 kg/m3, armrest top injection moulded in polyurethane and mounted on the injection moulded height adjustable type armrest, armrest height adjustable up to 45mm (approx) in 3 steps & width movement adjustable, 360 degree revolving type. mechanism, single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position locking with antishock feature, pneumatic height adjustment of 85mm spine bracket made of aluminum die cast piece connecting to back with mechanism, pedestal made of die cast alunimium fitted with 5 nos. twin wheel castors (castor wheel dia. 60mm approx.), base pedestal dia 650mm (approx.) and pitch center dia. 700mm with castors, twin wheel castors injection moulded in Nylon etc. all complete as per manufacturers specification, approved sample and direction of Engineer-in-Charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Manufacturing, providing and Placing High Back revolving chairs for Teacher of make M/s Rockworth -Sense HB (as per finally approved sample by department) of following dimensions with the following specifications. Providing and placing in position high back Revolving Chair with Adjustable headrest , Overall Chair size: 460-480W x 455- 480Dx 1220-1320Hmm , Backrest :The outer frame of the backrest made of injection moulded in black 20% Glass Filled Polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has fix lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black P.P. Lumber support size 280 mm (W) x 140 mm (H). Backrest size 780-810 mm (H) x 490-510mm (W). Spine made of reengineered black nylon. Backrest is tested for Static testing- 67kg (Functional Load) & 102 Kg (proof Loading) for 1 Min and cyclic testing- 57 Kg Loading for 1,20,000 cycles and will comply to ANSI/BIFMA X 5.1 standards. Seat : The seat is made up of 12 mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the plywood. Seat size 455-470mm(W) x 450-470 mm (D). Seating height is min.440mm and maxi. 540 mm respectively. Seat Foam: Foam made out of moulded polyurethane foam with the following properties. Average thickness of 65 mm (Width- 460-470 mm, Depth- 460-470 mm) and with the following properties: Density: 52-55 Kg/M³ , Hardness: 25±/3 KGF ,Compression Set: 10% Max ,Tensile Strength: 0.90 to 1.2 Kg/Cm² ,Resilience: 40%-60% ,Comfort / Indentation Hardness: 15.4 ,Weight: 650 gms ,Adjustable Armrest: Adjustable handle The armrest is made up of Thermo Polyurethane with 40 - 55 Shore Hardness and reinforced with 4 mm thick nylon insert. Arm pad size 235 mm (L) x 80 mm (W). The handle is fitted to the seat with seat/handle connecting strip assembly made of 35% Glass filled nylon 20 mm thick. Adjustable arm rest with height adjustment up to 70 mm. Minimum and Maximum height of armrest is 265 mm / 335 mm respectively. Arm Distance outside 640-650mm, Arm Distance inside 465-490mm .The front and back movement of armrest is 60 mm. The Handle is tested for Static Testing-75 Kg loading for 1 min (Functional Load) and 103 Kg for 15 secs (Proof Load) and cyclic testing- 41kgs for 60,000 cycles and will comply as per ANSI/BIFMA X 5.1. standards. Mechanism: single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position locking with antishock feature: Conventional mechanism with one lever control for lock and seat height adjustment. Mechanism made out of MS plate thickness is 3 mm and seat’s tilting angle is 3° - 10° and back tilting angle is 87° - 106°. Also, it has the back tension adjustment knob. The mechanism has a knob to adjust the back tilt tension and is tested for 300000 cycles as per ANSI/BIFMA X 5.1. Following are the approved mechanism options to use with the chair. Gaslift : Gas lift pipe diameter is 50 mm and has a height adjustment stroke of 112 mm. Gas lift tested for 100000 cycles as per ANSI/BIFMA X 5.1. Meets DIN 4550 Class – 4 and all applicable ANSI/BIFMA, EN performance standard. Base : Pedestal made of nylon base fitted with 5 nos. twin wheel castors (castor wheel dia. 60mm), base pedestal dia 60-70 mm and pitch center dia. 660-680mm with castors, twin wheel castors injection moulded in Nylon etc. all complete as per direction of Engineer-in-Charge. Nylon Base: The base is injection moulded in black 35% glass filled nylon and fitted with 5nos. The base is tested for static load of 1200 kg. Castors:.60 mm: The twin wheel castors are injection moulded in nylon 35% Glass Filled and diameter of castor is 60 mm. The castors are tested for 100000 cycles and will

Providing and placing in position medium back Revolving Chair, Overall Chair size: 460-480W x 455-480Dx 1000-1100Hmm ,Backrest :The outer frame of the backrest made of injection moulded in black 20% Glass Filled Polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has fix lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black P.P. Lumber support size 280 mm (W) x 140 mm (H). Backrest size 570-590 mm (H) x 490- 510mm (W). Spine made of reengineered black nylon. Backrest is tested for Static testing- 67kg (Functional Load) & 102 Kg (proof Loading) for 1 Min and cyclic testing- 57 Kg Loading for 1,20,000 cycles and will comply to ANSI/BIFMA X 5.1 standards. Seat : The seat is made up of 12 mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the plywood. Seat size 455-470mm(W) x 450-470 mm (D). Seating height is min.440mm and maxi. 540 mm respectively. Seat Foam: Foam made out of moulded polyurethane foam with the following properties. Average thickness of 55-65 mm with the following properties: Density: 52- 55 Kg/M³ , Hardness: 25±/3 KGF ,Compression Set: 10% Max ,Tensile Strength: 0.90 to 1.2 Kg/Cm² ,Resilience: 40%-60% ,Comfort / Indentation Hardness: 15.4 ,Weight: 650 gms ,Adjustable Armrest: Adjustable Handle : The armrest is made up of Thermo Polyurethane with 40 - 55 Shore Hardness and reinforced with 4 mm thick nylon insert. Arm pad size 235 mm (L) x 80 mm (W). The handle is fitted to the seat with seat/handle connecting strip assembly made of 35% Glass filled nylon 20 mm thick. Adjustable arm rest with height adjustment up to 70 mm. Minimum and Maximum height of armrest is 255 mm / 325 mm respectively. Arm Distance outside 640-650mm, Arm Distance inside 465-490mm .The front and back movement of armrest is 60 mm. The Handle is tested for Static Testing-75 Kg loading for 1 min (Functional Load) and 103 Kg for 15 secs (Proof Load) and cyclic testing- 41kgs for 60,000 cycles and will comply as per ANSI/BIFMA X 5.1. Standards. Mechanism: single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position locking with antishock feature: Conventional mechanism with one lever control for lock and seat height adjustment. Mechanism made out of MS plate thickness is 3 mm and seat’s tilting angle is 3°-10° and back tilting angle is 87°-106°. Also, it has the back tension adjustment knob. The mechanism has a knob to adjust the back tilt tension and is tested for 300000 cycles as per ANSI/BIFMA X 5.1. Following are the approved mechanism options to use with the chair. Gaslift: Gas lift pipe diameter is 50 mm and has a height adjustment stroke of 112 mm. Gas lift tested for 100000 cycles as per ANSI/BIFMA X 5.1. Meets DIN 4550 Class – 4 and all applicable ANSI/BIFMA, EN performance standard. Base:Pedestal made of nylon base fitted with 5 nos. twin wheel castors (castor wheel dia. 60mm), base pedestal dia 60-70 mm and pitch center dia. 660-680mm with castors, twin wheel castors injection moulded in Nylon etc. all complete as per direction of Engineer-in-Charge. Nylon Base: The base is injection moulded in black 35% glass filled nylon and fitted with 5nos. The base is tested for static load of 1200 kg. Castors:.60 mm: The twin wheel castors are injection moulded in nylon 35% Glass Filled and diameter of castor is 60 mm. The castors are tested for 100000 cycles and will comply as per ANSI/BIFMA X 5.1 standards. Fabric properties: Content :

Providing & Placing sofa with following specification ,Wooden structure of sofa to be fabricated using good quiality hardwood duly seasoned and applying anti-termite paint of approved brand & manufacture to ensure stability of the frame, On the wooden base frame of the sofa to be provided with M.S. helical spring, 1 side & 2 back with jute strips, with polyfill covered with jute & finished with thick marking cloth before doing fina finished with fabric (Titch). Seat - 40-45-32Kg/cum density PU Foam, 100mm thick, Back - 35-40Kg/cum density PU foam, 60mm thick, Sides (inside) - 40-45 Kg/cum density PU Foam, 45 mm thick Sides (outside) & back (back side) - 35-40 Kgcum density PU foam, 25mm thick. Seat shall rest on SS frame supported on legs made of SS chrome plated section of cone shape of height 225mm. All SS work should be in grade 304. Base of sofa should be made of 225mm H SS chrome plated curved base so as to give proper support to the seat. Height of the base of sofa shall be 200-250mm(approx). Finished width of arm shall be 100mm after upholstery work. Sofa to be fully upholstered using approved fabric (titch) of A grade of desired shade duly embossed including providing & fixing of all other related materials including hardwares etc. The sofa shall be provided with adjuster made uup of injection plastic in black color. The sofa can should be configured in different form as per the client requirement. Complete as directed by the Engineer in charge 2 seater sofa overall dimension - 1550mm W x 760-780mm D x 680-700mm H

Providing & Placing sofa with following specification ,Wooden structure of sofa to be fabricated using good quiality hardwood duly seasoned and applying anti-termite paint of approved brand & manufacture to ensure stability of the frame, On the wooden base frame of the sofa to be provided with M.S. helical spring, 1 side & 2 back with jute strips, with polyfill covered with jute & finished with thick marking cloth before doing fina finished with fabric (Titch). Seat - 40-45-32Kg/cum density PU Foam, 100mm thick, Back - 35-40Kg/cum density PU foam, 60mm thick, Sides (inside) - 40-45 Kg/cum density PU Foam, 45 mm thick Sides (outside) & back (back side) - 35-40 Kgcum density PU foam, 25mm thick. Seat shall rest on SS frame supported on legs made of SS chrome plated section of cone shape of height 225mm. All SS work should be in grade 304. Base of sofa should be made of 225mm H SS chrome plated curved base so as to give proper support to the seat. Height of the base of sofa shall be 200-250mm(approx). Finished width of arm shall be 100mm after upholstery work. Sofa to be fully upholstered using approved fabric (titch) of A grade of desired shade duly embossed including providing & fixing of all other related materials including hardwares etc. The sofa shall be provided with adjuster made uup of injection plastic in black color. The sofa can should be configured in different form as per the client requirement. Complete as directed by the Engineer in charge 1 seater sofa overall dimension - 810mm W x 760-780mm D x 680-700mm H

Providing & Placing sofa, with wooden structure fabricated using hardwood of approved quality, duly seasoned and anti- termite treated with approved chemical and methodology.The wooden base frame of the sofa shall be provided with M.S. helical spring along with high quality elastic belt 70-80mm, sides & back with 40-60mm elastic belt, seat & back covered with jute & foam covered with Polyfilla & finished with thick marking cloth before doing final finish with leatherette material The component specification shall be as follows Seat- 40-45Kg/cum density PU Foam, 100mm thick, Back– 32 - 40Kg/cum density PU foam, 50mm thick, Sides (inside)- 32-40 Kg/cum density PUFoam, 11mm thick Sides (outside) &back (back side) - 35-40 Kg cum density PU foam, 13mm thick. Seat shell rest on Wooden Legs supported solid wooden section of height 50-180mm. All Wooden work should be in White Ash / Teak wood polish with melamine & p.u coat Base of sofa should be infilled with suitable wooden sections so as to give proper support to the seat Height of the base of sofa. sofa shall be 75-220mm (Approx). Finished width of arm shall be 100 - 180mm (Approx) after upholstery work. Sofa to be fully upholstered using leatherette material of approved quality and shade , duly embossed including providing & fixing of all other required materials and hardware etc. all complete as directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. 2 seater sofa overall dimension - 1460mm W x 820-860mm D x 780-820mm H,

Providing & Placing sofa, with wooden structure fabricated using hardwood of approved quality, duly seasoned and anti- termite treated with approved chemical and methodology.The wooden base frame of the sofa shall be provided with M.S. helical spring along with high quality elastic belt 70-80mm, sides & back with 40-60mm elastic belt, seat & back covered with jute & foam covered with Polyfilla & finished with thick marking cloth before doing final finish with leatherette material The component specification shall be as follows Seat- 40-45Kg/cum density PU Foam, 100mm thick, Back– 32 - 40Kg/cum density PU foam, 50mm thick, Sides (inside)- 32-40 Kg/cum density PUFoam, 11mm thick Sides (outside) &back (back side) - 35-40 Kg cum density PU foam, 13mm thick. Seat shell rest on Wooden Legs supported solid wooden section of height 50-180mm. All Wooden work should be in White Ash / Teak wood polish with melamine & p.u coat Base of sofa should be infilled with suitable wooden sections so as to give proper support to the seat Height of the base of sofa. sofa shall be 75-220mm (Approx). Finished width of arm shall be 100 - 180mm (Approx) after upholstery work. Sofa to be fully upholstered using leatherette material of approved quality and shade , duly embossed including providing & fixing of all other required materials and hardware etc. all complete as directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. 1 seater sofa overall dimension - 820mm W x 820-860mm D x 780-820mm H,

Providing & fixing continuous Sofa with 18mm thick side & back cover decorative and lamination factory pressed BWP grade marine ply as per IS 710 of approved brand finished with fire retardant Fabric of approved make & necessary hardwood & plywood framing. Foam (Medium firm) density should be 33 lbs / cuft. Cost inclusive of Fabric as shown in image below. with wooden structure fabricated using hardwood of approved quality, duly seasoned and anti-termite treated with approved chemical and methodology.The wooden base frame of the sofa shall be provided with M.S. helical spring along with high quality elastic belt 70-80mm, sides & back with 40-60mm elastic belt, seat & back covered with jute & foam covered with Polyfilla & finished with thick marking cloth before doing final finish with leatherette material The component specification shall be as follows Seat- 40-45Kg/cum density PU Foam, 100mm thick, Back– 32 - 40Kg/cum density PU foam, 50mm thick, Sides (inside)- 32-40 Kg/cum density PUFoam, 11mm thick Sides (outside) &back (back side) - 35-40 Kg cum density PU foam, 13mm thick. Seat shell rest on Wooden Legs supported solid wooden section of height 50-180mm. All Wooden work should be in White Ash / Teak wood polish with melamine & p.u coat Base of sofa should be infilled with suitable wooden sections so as to give proper support to the seat Height of the base of sofa. sofa shall be 80-160mm (Approx). Finished width of arm shall be 90 - 120mm (Approx) after upholstery work. Sofa to be fully upholstered using leatherette material of approved quality and shade , duly embossed including providing & fixing of all other required materials and hardware etc. all complete as directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. 3 seater sofa overall dimension - 2050mm W x 640-680mm D x 700-740mm H, Seating Height 425mm

Providing & fixing continuous Sofa with 18mm thick side & back cover decorative and lamination factory pressed BWP grade marine ply as per IS 710 of approved brand finished with fire retardant Fabric of approved make & necessary hardwood & plywood framing. Foam (Medium firm) density should be 33 lbs / cuft. Cost inclusive of Fabric as shown in image below. with wooden structure fabricated using hardwood of approved quality, duly seasoned and anti-termite treated with approved chemical and methodology.The wooden base frame of the sofa shall be provided with M.S. helical spring along with high quality elastic belt 70-80mm, sides & back with 40-60mm elastic belt, seat & back covered with jute & foam covered with Polyfilla & finished with thick marking cloth before doing final finish with leatherette material The component specification shall be as follows Seat- 40-45Kg/cum density PU Foam, 100mm thick, Back– 32 - 40Kg/cum density PU foam, 50mm thick, Sides (inside)- 32-40 Kg/cum density PUFoam, 11mm thick Sides (outside) &back (back side) - 35-40 Kg cum density PU foam, 13mm thick. Seat shell rest on Wooden Legs supported solid wooden section of height 50-180mm. All Wooden work should be in White Ash / Teak wood polish with melamine & p.u coat Base of sofa should be infilled with suitable wooden sections so as to give proper support to the seat Height of the base of sofa. sofa shall be 80-160mm (Approx). Finished width of arm shall be 90 - 120mm (Approx) after upholstery work. Sofa to be fully upholstered using leatherette material of approved quality and shade , duly embossed including providing & fixing of all other required materials and hardware etc. all complete as directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. 2 seater sofa overall dimension - 1590mm W x 640-680mm D x 700-740mm H,Seating Height 425mm

Providing & fixing continuous Sofa with 18mm thick side & back cover decorative and lamination factory pressed BWP grade marine ply as per IS 710 of approved brand finished with fire retardant Fabric of approved make & necessary hardwood & plywood framing. Foam (Medium firm) density should be 33 lbs / cuft. Cost inclusive of Fabric as shown in image below. with wooden structure fabricated using hardwood of approved quality, duly seasoned and anti-termite treated with approved chemical and methodology.The wooden base frame of the sofa shall be provided with M.S. helical spring along with high quality elastic belt 70-80mm, sides & back with 40-60mm elastic belt, seat & back covered with jute & foam covered with Polyfilla & finished with thick marking cloth before doing final finish with leatherette material The component specification shall be as follows Seat- 40-45Kg/cum density PU Foam, 100mm thick, Back– 32 - 40Kg/cum density PU foam, 50mm thick, Sides (inside)- 32-40 Kg/cum density PUFoam, 11mm thick Sides (outside) &back (back side) - 35-40 Kg cum density PU foam, 13mm thick. Seat shell rest on Wooden Legs supported solid wooden section of height 50-180mm. All Wooden work should be in White Ash / Teak wood polish with melamine & p.u coat Base of sofa should be infilled with suitable wooden sections so as to give proper support to the seat Height of the base of sofa. sofa shall be 80-160mm (Approx). Finished width of arm shall be 90 - 120mm (Approx) after upholstery work. Sofa to be fully upholstered using leatherette material of approved quality and shade , duly embossed including providing & fixing of all other required materials and hardware etc. all complete as directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. 1 seater sofa overall dimension - 850mm W x 640-680mm D x 700-740mm H, Seating Height 425mm

Providing and fixing in position of Auditorium Chairs With Writable tablet of overall dimensions of 515mm (W) x 720mm (D) x 980mm (H). Seat Height from floor should be of 440mm as per Ergonomic standards. The chairs should have following description :The dimensions after push back shall be 515mm wide and seat and Backrest should be made with cutting and moulded foam covered by acrylic fabric.The shell should made up of plywood cover of termite, fire resistant plywood and should be capable of bearing minimum height of 120 kgs.Seat should be with buffering mechanism to enable soft closing of seat when it is folded and all hole on seat shelf should be noise absorbing.Armrest of chairs should be of fixed type made out of wood and should be provided with option of folding table to be used as writing pad.Legs of chairs should be made with cold rolled cold annealed steel duly powder coated with 80-100 micron thickness to provide smooth and clean surface.Seat should be foldable to enable comfortable seating, maintenance and to provide space utilization to walk around. Seat and Back should be wrapped with Titch make O-Farbic of desire colour as per Engineer-Incharge with zero formaldehyde glue. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Manufacturing, providing and placing in position machine made factory assembled Seminar Hall Table of make M/s Rockworth (as per finally approved sample by department) of following dimensions with the following specifications. Supplying, and placing in position of Table of size: 3600Wx 750D x 1000/740Hmm . Whose top and Side Panel/legs are made of 38mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thicness 16 mm cover with Melamine Edge-Banding(PVC) 2 mm. Also legs are made of Particle board wood Grade E-1 (Environmental Friendly) thicness 38 mm, cover with Melamine. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Manufacturing, providing and Placing Center & Corner table of make M/s Rockworth (as per finally approved sample by department) of following dimensions with the following specifications. Providing and fixing tables of Centre table Size - 1100mm W x 500mm D x 365mm H for whose top & Base are made of Particle board wood Grade E-1(Environmental Friendly), thickness 19mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty

Providing and fixing tables of Side table Size - 450mm W x 450mm D x 365mm H for whose top & Base are made of Particle board wood Grade E-1(Environmental Friendly), thickness 19mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty

Providing and fixing tables of Centre table Size - 1200mm W x 600mm D x 400mm H, for whose top is made of Particle board wood Grade E-1(Environmental Friendly), thickness 25 mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992).The understructure is made of teak wood leg With MS Bracket for support.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Providing and fixing tables of Side table Size - 500mm W x 500mm D x 365mm H, for whose top is made of Particle board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992).The understructure is made of teak wood leg With MS Bracket for support.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Providing & Placing Reception desk Top & Legs are made up of 38mm thick E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The exposed edge of worktop shall be secured with 2mm thick PVC edge banding tape of approved colour. The top shall be made of 38mm thick pre laminated particle board with PVC edges. Front hanging panel is madeout of 18mm thick Decorative E1 Gedae board . The product should be from approved make, Complete as per specification mentioned above & image under the guidance and aprroval of project architect/consultant & engineer in charge. Drawer Unit : 3 drawer Melamine(1D+1D+1F ) pedestal of overall dimensions internal and external dimensions 420 mm (W) x 450 mm (D) x 600 mm ( H). Drawer body should be made of E1 grade 1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The exposed edge of worktop shall be secured with 2mm thick PVC edge banding tape of approved colour.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Reception Table : 2800Wx 750/300Dx 1100/740Hmm

Providing ,Supplying , fixing and commisoning factory built GANDHI JI STATUE made by brass and diamension are 3.2 m x 3.2 x 4 m is erected by two hydras and complete fitting on a RCC base as per direction of Engineer-in-charge.

Providing, Suppling and fixing of WATER PURIFIER FILTER - SODA ASH DOSER, AUTOMATIC CHLORINE DOSER WITH 100 LTR TANK, MULTIGRADE FILTER (MODEL - TATA -2472,4 RON REMOVAL FILTER (MODEL- 2472-4" T/B TATA), TATA MAKE IRF (3672) for LAKE BODY FILTRATION WORK along with CPVC pipes including all fittings and CPVC cement Solvent including all Service Charges, trenching, refilling & testing of joints completed as per direction of Engineer in Charge.

PLUMBING ITEMS Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 32 mm dia nominal dia. Pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 40 mm dia nominal dia. Pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia nominal dia. Pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 65 mm dia nominal dia. Pipe

EXTRA HVAC NEW ITEMS Supply, Installation, Testing and commissioning of factory built ceiling Suspended chilled water double skin type horizontal/vertical air handling units made of 25mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 4 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for varialbe frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation,150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification and of following capacities. CS AHU-2750 CFM 50mm Static

Supply, Installation, Testing and commissioning of factory built ceiling Suspended chilled water double skin type horizontal/vertical air handling units made of 25mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 4 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for varialbe frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation,150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification and of following capacities. CS AHU-4800 CFM 50mm Static

Supply, Installation, Testing and commissioning of factory built ceiling Suspended chilled water double skin type horizontal/vertical air handling units made of 25mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 4 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for varialbe frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation,150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification and of following capacities. CS AHU-5500 CFM 50mm Static

Butter fly Valve (Manual) with CI body SS Disc,Nitrile Rubber Seal & O-Ring PN 16 pressure rating for chilled water/hot water circulation as specified. 50 mm dia. (32 mm thick insulation)

Y-Strainer of Ductile CI Body flanged ends with stainless steel strainer for chilled/hot water circulation including insulation as specified. 50 mm dia. (32 mm thick insulation)

Providing and fixing in position the industrialty pepressure gauges with gunmetal / brass valves complete as required.

Providing & Fixing in position the mercury in glass with industrial type thermometers.

Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 25mm Dia

Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 50mm Dia

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 25mm Dia dia. (19 mm thick insulation)

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 40mm Dia dia. (19 mm thick insulation)

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 50mm Dia dia. (19 mm thick insulation)

Supply, Installation, Testing and commissioning of factory built ceiling Suspended chilled water double skin type horizontal/vertical air handling units made of 25mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 4 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for varialbe frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation,150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification and of following capacities. CS AHU-1100 CFM 45mm Static

Supply, Installation, Testing and commissioning of factory built ceiling Suspended chilled water double skin type horizontal/vertical air handling units made of 25mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 4 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for varialbe frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation,150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification and of following capacities. CS AHU-1500 CFM 45mm Static

Supply, Installation, Testing and commissioning of factory built ceiling Suspended chilled water double skin type horizontal/vertical air handling units made of 25mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 4 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for varialbe frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation,150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification and of following capacities. CS AHU-1900 CFM 45mm Static

Supply of the following Ball Valves duly insulated as per specifications and drawings. Ball valve shall be screwed type brass/bronze lever operated, quarter turn ball valve (screwed type) of full flow with bronze /forged brass hard chrome plated ball with setting & gland of superior quality of preferably PN 16 rating. 25mm Dia

Supply of the following Ball Valves with strainer duly insulated as per specifications and drawings. Ball valve shall be screwed type brass/bronze lever operated, quarter turn ball valve (screwed type) of full flow with bronze /forged brass hard chrome plated ball with setting & gland of superior quality of preferably PN 16 rating. 25mm Dia

DRAIN PIPING : Providing and fixing of PVC drain pipe of 6 Kg /cm2 pressure rating complete with 6mm thick closed cell nitrile rubber insulation with mechanical protection (Aluminium laminated face), fittings, supports, valves as per specifications & drawings. 32 mm dia

Supply of ducted Inline Fans of GSS construction duly powder coated (rectangular box type for upto 20 mm WG SP and circular type for 10 mm WG SP) with centrifugal blower and motor encased in sheet metal casing, canvas connection etc. The Fan motor shall be suitable for operation on 220 V± 10%, 50 Hz, 1 phase AC supply. The Fan assembly shall conform to specifications and in accordance with requirements of drawings and Schedule of Quantities. Air Quantity : 600 CFM Static Pressure : 10 mm wg Motorrating : As Required

Supply of AMCA certified for sound and air performance (FEG) Tube Axial fan complete with tube casing in MS standard construction powder coated, aluminium impeller with adjustable blade angles,vibration isolator and directly coupled to TEFC Sq.cage induction motor, suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. as per specification & drawing complete as required. Air Quantity :1500-1600 CFM Static Pressure : 20 mm wg Duty : Corridor FA

Supply of AMCA certified for sound and air performance (FEG) Tube Axial fan complete with tube casing in MS standard construction powder coated, aluminium impeller with adjustable blade angles,vibration isolator and directly coupled to TEFC Sq.cage induction motor, suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. as per specification & drawing complete as required. Air Quantity :2400-2700 CFM Static Pressure : 20 mm wg Duty : Corridor FA

Supply of AMCA certified for sound and air performance (FEG) Tube Axial fan complete with tube casing in MS standard construction powder coated, aluminium impeller with adjustable blade angles,vibration isolator and directly coupled to TEFC Sq.cage induction motor, suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. as per specification & drawing complete as required. Air Quantity :14000 CFM Static Pressure : 30 mm wg Duty : lift well press.

Supply of AMCA certified for sound and air performance (FEG) Tube Axial fan complete with tube casing in MS standard construction powder coated, aluminium impeller with adjustable blade angles,vibration isolator and directly coupled to TEFC Sq.cage induction motor, suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. as per specification & drawing complete as required. Air Quantity :19000 CFM Static Pressure : 30 mm wg Duty : stair press.

Supply of AMCA certified for sound and air performance (FEG) Tube Axial fan complete with tube casing in MS standard construction powder coated, aluminium impeller with adjustable blade angles,vibration isolator and directly coupled to TEFC Sq.cage induction motor, suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. as per specification & drawing complete as required. Air Quantity :32500 CFM Static Pressure : 30 mm wg Duty : lift lobby press.

Supply of AMCA certified for sound and air performance (FEG) Tube Axial fan complete with tube casing in MS standard construction powder coated, aluminium impeller with adjustable blade angles,vibration isolator and directly coupled to TEFC Sq.cage induction motor, Class H insulation 2 hr fire rated at 250C as per UL/BSEN suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. as per specification & drawing complete as required. Air Quantity :36500 CFM Static Pressure : 30 mm wg Duty : Corridor EA at terrace

REINSTALLATION WORK ReInstallation, testing commisiining of all existing air-conditioning FCU and make it oprational in all respect without any fault.These all item executed judicially. FCU capcity is as follows. - 2.5TR FCU

ReInstallation, testing commisiining of all existing air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 4800CFM CS AHU

ReInstallation, testing commisiining of all existing AXIAL FAN AND make it oprational in all respect without any fault.These all item executed judicially. FAN capcity is as follows. - 2600CFM AXIAL FAN

DISMANTLING WORK Dismantling/unistallation of existing AXIAL FAN which is not use in drawing, & shifting in storage area OR SPECIFIED LOCATION . FAN capcity is as follows. - 2600CFM AXIAL

Dismantling/unistallation of existing AXIAL FAN which is not use in drawing, & shifting in storage area OR SPECIFIED LOCATION . FAN capcity is as follows. - 1000-2100CFM AXIAL

Dismantling/unistallation of existing air-conditioning AHU which is not use in drawing, & shifting in storage area . AHU capcity is as follows. - 1600CFM CS AHU

Dismantling/unistallation of existing air-conditioning AHU which is not use in drawing, & shifting in storage area . AHU capcity is as follows. - 1000CFM CS AHU

Dismantling/unistallation of existing air-conditioning AHU which is not use in drawing, & shifting in storage area . AHU capcity is as follows. - 1350CFM CS AHU

Dismantling/unistallation of existing air-conditioning AHU which is not use in drawing, & shifting in storage area . AHU capcity is as follows. - 3650CFM CS AHU

Dismantling/unistallation of existing air-conditioning AHU which is not use in drawing, & shifting in storage area . AHU capcity is as follows. - 4000CFM CS AHU

Dismantling/unistallation of existing air-conditioning AHU which is not use in drawing, & shifting in storage area . AHU capcity is as follows. - 5200CFM Fm AHU

Dismantling/unistallation of existing air-conditioning AHU which is not use in drawing, & shifting in storage area . AHU capcity is as follows. - 5700CFM Fm AHU

Dismantling/unistallation of existing air-conditioning AHU which is not use in drawing, & shifting in storage area . AHU capcity is as follows. - 7500CFM Fm AHU

Dismantling/unistallation of existing air-conditioning FCU which is not use in drawing, & shifting in storage area . FCU capcity is as follows. - 1.0TR FCU

WATER PURIFIER FILTER - SODA ASH DOSER

AUTOMATIC CHLORINE DOSER WITH 100 LTR TANK

MULTIGRADE FILTER (MODEL - TATA -2472)

4 RON REMOVAL FILTER (MODEL- 2472-4" T/B TATA)

TATA MAKE IRF (3672)

SERVICE CHARGE - FITTING & INSTALLATION

LOCAL TRANSPORT

Butter fly Valve (Manual) with CI body SS Disc,Nitrile Rubber Seal & O-Ring PN 16 pressure rating for chilled water/hot water circulation as specified. 50 mm dia.

Butter fly Valve (Manual) with CI body SS Disc,Nitrile Rubber Seal & O-Ring PN 16 pressure rating for chilled water/hot water circulation as specified. 100 mm dia

Butter fly Valve (Manual) with CI body SS Disc,Nitrile Rubber Seal & O-Ring PN 16 pressure rating for chilled water/hot water circulation as specified. 80 mm dia

Butter fly Valve (Manual) with CI body SS Disc,Nitrile Rubber Seal & O-Ring PN 16 pressure rating for chilled water/hot water circulation as specified. 65 mm dia

Butter fly Valve (Manual) with CI body SS Disc,Nitrile Rubber Seal & O-Ring PN 16 pressure rating for chilled water/hot water circulation as specified. 40 mm dia

Butter fly Valve (Manual) with CI body SS Disc,Nitrile Rubber Seal & O-Ring PN 16 pressure rating for chilled water/hot water circulation as specified. 32 mm dia(Ball valve)

Butter fly Valve (Manual) with CI body SS Disc,Nitrile Rubber Seal & O-Ring PN 16 pressure rating for chilled water/hot water circulation as specified. 25 mm dia (Ball valve)

Butter fly Valve (Manual) with CI body SS Disc,Nitrile Rubber Seal & O-Ring PN 16 pressure rating for chilled water/hot water circulation as specified. 20 mm dia (Ball valve)

Y-Strainer of Ductile CI Body flanged ends with stainless steel strainer for chilled/hot water circulation including insulation as specified. 50 mm dia

Y-Strainer of Ductile CI Body flanged ends with stainless steel strainer for chilled/hot water circulation including insulation as specified. 40 mm dia

Y-Strainer of Ductile CI Body flanged ends with stainless steel strainer for chilled/hot water circulation including insulation as specified. 32 mm dia

Y-Strainer of Ductile CI Body flanged ends with stainless steel strainer for chilled/hot water circulation including insulation as specified. 25 mm dia

Y-Strainer of Ductile CI Body flanged ends with stainless steel strainer for chilled/hot water circulation including insulation as specified. 20 mm dia

Providing and fixing in position the industrialty pepressure gauges with gunmetal / brass valves complete as required.

Providing & Fixing in position the mercury in glass with industrial type thermometers.

Providing and fixing Auto air vents (Brass MOC) of following size-20 MM

Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 25mm Dia

Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 50mm Dia

Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 40 mm dia

Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 32 mm dia

Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 20 mm dia

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 25mm Dia dia. (19 mm thick insulation)

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 50mm Dia dia.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 200 mm dia.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 150 mm dia.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 125 mm dia.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 100 mm dia.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 80 mm dia.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 65 mm dia.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building & at terrace (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 40-55 Kg / cu m density, insulation material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180,thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation,with reinforced 7 mil woven glass fiber covering in and applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. 32 mm dia.

Insulated Chilled Water Pipeing (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 Kg / cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g pilythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip (as per IS : 1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7 mm thick MS sheet for pipes of 400mm dia and above. 200 mm dia.

Insulated Chilled Water Pipeing (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 Kg / cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g pilythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip (as per IS : 1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7 mm thick MS sheet for pipes of 400mm dia and above. 150 mm dia.

Insulated Chilled Water Pipeing (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 Kg / cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g pilythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip (as per IS : 1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7 mm thick MS sheet for pipes of 400mm dia and above. 125 mm dia.

Insulated Chilled Water Pipeing (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 Kg / cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g pilythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip (as per IS : 1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7 mm thick MS sheet for pipes of 400mm dia and above. 100 mm dia.

Insulated Chilled Water Pipeing (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 Kg / cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g pilythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip (as per IS : 1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7 mm thick MS sheet for pipes of 400mm dia and above. 80 mm dia.

Insulated Chilled Water Pipeing (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 Kg / cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g pilythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip (as per IS : 1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7 mm thick MS sheet for pipes of 400mm dia and above. 65 mm dia.

Insulated Chilled Water Pipeing (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 Kg / cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g pilythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip (as per IS : 1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7 mm thick MS sheet for pipes of 400mm dia and above. 50 mm dia.

Insulated Chilled Water Pipeing (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 Kg / cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g pilythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip (as per IS : 1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7 mm thick MS sheet for pipes of 400mm dia and above. 32 mm dia.

Insulated Chilled Water Pipeing (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 Kg / cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g pilythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip (as per IS : 1322 as amended up to date) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7 mm thick MS sheet for pipes of 400mm dia and above. 25 mm dia.

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 4800CFM-12.1TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1.0TR FCU-1000 CFM

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 2.5TR FCU-1000 CFM

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1.0TR FCU-400 CFM

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 3650CFM-5.1TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1000CFM-1.23TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1100CFM-1.5TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1050CFM-1.7TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1350CFM-2.66TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1350CFM-2.1TR CSU AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1500CFM-1.37TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1700CFM-3.1TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1900CFM-3TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 2100CFM-4.07TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 2050CFM-3.3 CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 4800CFM-9.5TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 2750CFM-5.1TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 3650CFM-5.1TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 3000CFM-5.3TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 4000CFM-6.9TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 5500CFM-11.1TR CS AHU Static Pressure:-40 mm WC Pressure 4RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 4800CFM-12.57TR FM AHU Static Pressure:-65 mm WC Pressure 6RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning AHU & FCU and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 7500CFM FM AHU Static Pressure:-65 mm WC Pressure 6RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Supply and instalation, testing commisiining of all air-conditioning TFA and make it oprational in all respect without any fault.These all item executed judicially. AHU capcity is as follows. - 1225 CFM-7 TR TFA CSU AHU Static Pressure:-65 mm WC Pressure 6RD Cooling Coil or As Required Meeting Functional Requirement,(Filter -MERV-8 - 90% efficiency Down to 10 Micron) cooling coil- (CHW)

Providing and fixing of PVC drain pipe of 6 Kg /cm2 pressure rating complete with 9mm thick closed cell nitrile rubber insulation, fittings, supports as per specifications & drawings. 32 mm Dia

Providing and fixing of PVC drain pipe of 6 Kg /cm2 pressure rating complete with 9mm thick closed cell nitrile rubber insulation, fittings, supports as per specifications & drawings. 40 mm Dia

Providing and fixing of PVC drain pipe of 6 Kg /cm2 pressure rating complete with 9mm thick closed cell nitrile rubber insulation, fittings, supports as per specifications & drawings. 50 mm Dia

Air distribution Systems Supply & installation of rectangular duct fabricated out of GSS ducts with 120 GSM coating GSS slip joints and end flanges to suit site condition complete with Galvanised slotted channel for bottom support of minimum thickness 2mm . 24 G

Air distribution Systems Supply & installation of rectangular duct fabricated out of GSS ducts with 120 GSM coating GSS slip joints and end flanges to suit site condition complete with Galvanised slotted channel for bottom support of minimum thickness 2mm . 22 G

Air distribution Systems Supply & installation of rectangular duct fabricated out of GSS ducts with 120 GSM coating GSS slip joints and end flanges to suit site condition complete with Galvanised slotted channel for bottom support of minimum thickness 2mm . 20 G

supply and installation of the GSS volume control dampers made of 18 G GSS frame and 20 G GSS blades

Supply and installation of the duct mounted fire dampers made of 18 G GSS frame and 20 G blades ( fuse link type)

Supplying, fixing, testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers, complete as required. Measured on neck size.

Supplying, fixing, testing commissioning of return air diffusers of powder coated aluminium without aluminium volume control dampers, complete as required. Measured on neck size.

Supplying, fixing, testing & commissioning of powder coated extruded aluminium section supply air grills linear/descrete with aluminium volume control dampers in AC area as requied.

Supplying, fixing, testing & commissioning of canvass connection at AHU/FCU mouth measured on area of air flow.

INSULATION WORKS Thermal insulation of the ducting with 19 mm nitrile rubber insulation AL foil faced with PVC tape with class o material having density of 50 kg/cum with k value of .032w/mk

Acoustic insulation of the duct with 12 mm thick open cell elastomeric insualtion with density of 210 kg/cum , with k value of .55 w/mk stuck with sr 998 adhesive for the initial 6 rmt of the duct

AHU PANEL FLOOR PANEL. Supply, installation, testing and commissioning of following distribution boards totally enclosed compartmentalized, cubicle floor mounted, indoor type IP:42, factory fabricated with 2 mm thick CRCA sheet, with Aluminium bus bars (both for main and neutral bus bars), complete with switch/mountings cable terminations, inter-connections as required, for 415 volts, 3 phase, 4 wire 50 HZ AC supply for DOL STARTER.

Supply, installation, testing and commissioning of following distribution boards totally enclosed compartmentalized, cubicle floor mounted, indoor type IP:42, factory fabricated with 2 mm thick CRCA sheet, with Aluminium bus bars (both for main and neutral bus bars), complete with switch/mountings cable terminations, inter-connections as required, for 415 volts, 3 phase, 4 wire 50 HZ AC supply for STAR DELTA STARTER.

LT Cables Supply, installation, testing and commissioning of XLPE insulated, PVC sheathed Overall FRLS, armoured, 1.1 KV grade aluminium/Copper conductor cables IS:7098 (Part 1) marked , including cable tray and end termination for AC Plant Room at Roof. 3cx 6 qmm cable , CU.Armoured cable.

LT Cables Supply, installation, testing and commissioning of XLPE insulated, PVC sheathed Overall FRLS, armoured, 1.1 KV grade aluminium/Copper conductor cables IS:7098 (Part 1) marked , including cable tray and end termination for AC Plant Room at Roof. 3cx 4 sqmm cable , CU.Armoured cable.

LT Cables Supply, installation, testing and commissioning of XLPE insulated, PVC sheathed Overall FRLS, armoured, 1.1 KV grade aluminium/Copper conductor cables IS:7098 (Part 1) marked , including cable tray and end termination for AC Plant Room at Roof. 3cx 2.5 sqmm cable , CU.Armoured cable.

LT Cables Supply, installation, testing and commissioning of XLPE insulated, PVC sheathed Overall FRLS, armoured, 1.1 KV grade aluminium/Copper conductor cables IS:7098 (Part 1) marked , including cable tray and end termination for AC Plant Room at Roof. 3cx1.5 sqmm Cu cable.

LT Cables Supply, installation, testing and commissioning of XLPE insulated, PVC sheathed Overall FRLS, armoured, 1.1 KV grade aluminium/Copper conductor cables IS:7098 (Part 1) marked , including cable tray and end termination for AC Plant Room at Roof. 2.5 sqmm wire

LT Cables Supply, installation, testing and commissioning of XLPE insulated, PVC sheathed Overall FRLS, armoured, 1.1 KV grade aluminium/Copper conductor cables IS:7098 (Part 1) marked , including cable tray and end termination for AC Plant Room at Roof. 7cx 1.5 sqmm cable , CU.Armoured cable.

Supplying,testing and commissioning of M,S Channel,Angle and plate ETC.

HIGH-TECH ECOGREEN CONTRACTORS LLP (BID ID -271559)