SPECIAL REPAIRS OF FLOOR TILING AND REWIRING OF BUILDING NO P-175, WG-V OF CHQ WING ARTY CENTRE UNDER GE NASIK ROAD CAMP

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premises complete all as specifed and directed

Demoltion of unreinforced cement concrete in ground floor and paving not exceeding 15 cm thickness

M&L cement concrete 1:4:8 Type D2 (40 mm graded aggregate) Iin 75 mm thick sub base

M&L for rendering 10 mm thick on than fair faces of brick work or concrete surfaces in cement mortar 1:4 as backing coat for fixing tiles.

M&L Non-skid coloured ceramic tiles 7 to 8 mm thick square/rectangular) area of each tile exceeding 0.18Sqm but not exceeding 0.38 Sqm, in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile all as specified and directed by Engr-in-charge

M & L for coloured non skid ceramic tiles 7 to 8 mm thick area of each tile 0.18 sqm but not exc 0.38 sqm in floors, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in cement mortar 1:6 all as specified and directed by Engr-in-charge

Taking down cement plaster on brick or stone wall etc including raking out joints hacking for keys scrubbing down with water etc. including removing all the debris out side MD land

M&L for rendering 15 mm thick cement plaster on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 rendering is to be finished even and smooth without using extra cement

M&L preparation of old plastered or un-plastered by brooming down or steel wire brushing, scraping down smoke shoot, mould mass and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash on ceiling and all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of Acrylic weather proof exterior paint over water based primer(Make: APEX of Asian Paint or equivalent) complete all as specified and directed.

M & L for Complete removal of existing treatment on wall surfaces including preparation (i.e. brooming down plastered / unplastered surfaces complete) and applying two coats of Acrylic weather proof exterior paint over water based primer(Make: APEX of Asian Paint or equivalent) complete all as specified and directed.

M & L for Complete removal of existing treatment and applying 3 mm thick Birla white putty incl necessary repair and one coat of primer and two coats of OBD, white or tinted on walls all as specified and directed by Engr-In-Charge.

M&L for preparing plastered surfaces and applying two coats of oil bound distemper over one coat of primer including 3mm thick wall care putty on surfaces of walls complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc. Note - old serviceable switch/ socket/ regulator/ switch-socket/call bell/bell push shall be reused against apropriate items, all as specified and directed by Engr-in-Charge.

Taking down unserviceable/partly serviceable light fittings any type, tube light fitting and fixtures, etc, and making good to the disturbed surfaces of walls/floor etc to macth with existing surfaces including white washing/colour washing/distempering to match with existing wall / floor / ceiling finishes. NOTE- old serviceable fitting shall be reused against apropriate items, all as specified and directed by Engr-in-Charge

Taking down and hanging during point wiring of ceiling fan/exhaust fan of any size and sweep in proper manner and connecting up including provision of cable from ceiling rose or connector to fan all as per specified and directed by Engr-in-Charge

Dismantling unserviceable main switch/DBs with MCBs and wooden board including making good disturbed surface of wall.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surfaces.

Point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade surface casing capping not less then 20 mm width with MS sheet metal sunken switch/Terminal box 1.2 mm thick and ebonite switch board cover 3.0 mm thick or PVC moulded switch board and brass screws with cup washers including all necessary wall cutting and making good disturbed surface all as directed and specified . Note : Cutting chases and making good to match with the adjoining surface shall be included in the unit rate.

(a) One light point controlled by one, one way switch

(b) One ceiling /exhaust fan point controlled by one switch and regulator

(c) One 3 pin 5 amp socket out point on the same board with other switches.

(d) One3 pin 5 amps socket out let point on independent board

All as per same in item No 06 above but for one socket outlet 15 amp on independent board with 2.5 Sq. mm cable and 2.5 Sq.mm. earth wire.

S &F in repair Switch piano flush type single pole one way 5 amps.

S &F in repair Socket out let 2 in one, 5/3 pin 5Amp

S &F in repair Switch socket combination 5 Amps 5 pin flush type

S &F in repair Switch socket combination 5 in 1, 5 pin 5/15 Amps flush type universal .

S &F in repair Ceiling rose, surface bakelite 65x50 mm three terminal

S &F in repair Electronic regulator 100/120 Watt step type

Supply and fixing in repair of lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including LED bulb 9 watt.

S & F 20 Watt Batten (4 feet) suitable for LED T8 lamps including coneecting up with 2 core flexible coppper conductor cable and mounting clamps & PVC squre box 75x75mm - 2 Nos etc, all as specified and directed by Engr-in-Charge.

S & F 20 Watt LED Tube Light (4 feet) suitable for T8 Batten including provision of suitable type of bipin holders- 02 Nos for each fitting, internal wiring of old fitings/fixtures if required, all as specified and directed by Engr-in-Charge

Supply & fix LED tube light along with fixture,10 W, 2 Feet including coneecting up with 2 core flexible coppper conductor cable and mounting clamps & PVC squre box 75x75mm - 2 Nos etc, all as specified and directed by Engr-in-Charge .

Refixing of tube light from exisiting position to new position as required at site all as directed and specified . (Note:- The old serviceable fittings will be used as removed against item No-2 above)

Refixing of wooden/PVC rectangular block for mounting, switches, sockets,fan regulator, call bell, bell push etc. with 3 mm thick plastic laminated sheet cover/helum sheet of ISI mark as required on ground including casing capping /conduit of any size, all as specified and directed by Engr-in-Charge. (Old serviceable material will be used as removed against item No-14 above)

Refixing of DB's including MCB's of any size, all as specified and directed by Engr-in-Charge. (Old serviceable material will be used as removed against item No-14 above)

Supply and fix LED security/street light 15 W IP 65 , including coneecting up with 2/3 core flexible coppper conductor cable , compete all as specified and directed by Engr-in-Charge.

Fabrication,supply & fixing of GI pipe bracket up to 40 mm dia- 0.9m long & 2 set of clamps made out of 30x5mm ms flat & fixed with anchor bolt suitable for 12/15 w LED security light fitting

Material and labour for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 2.5 Sqmm, earth continuity conductor of size 2.5 Sqmm to be drawn through and including PVC CASING CAPING not less then 20mm dia medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge. Notes:- Two wires of 2.5 sqmm and one wire of 2.5 sqmm for earthing and one run of PVC casing/caping shall be measured as one unit.

Material and labour for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 4 Sqmm, earth continuity conductor of size 4 Sqmm to be drawn through and including PVC casing capping not less then 32mm dia medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge. Notes:- Two wires of 4 sqmm and one wire of 4 sqmm for earthing and one run of PVC casing capping shall be measured as one unit.

Material and labour for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through and including PVC CASING CAPPING not less then 32mm dia medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge. Notes:- Two wires of 6 sqmm and one wire of 6 sqmm and one run of PVC casing capping shall be measured as one unit.

S & F 4 way MCCB powerline vertical DBs in double door suitable for TP/FP MCCB, bus bar with current rating capacity upto 160A, IP-43-IK09 protection grade complete all as specified and directed by Engr-in-Charge,

S & F in repair for MCB DB made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, IP-43-IK09 protection grade , 415 Volts TPN with 4 way Double door including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed

S & F in repair, MCB DB made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, earth bar and Din rail , 240Volts SPN with 8 way Double door , IP-43-IK09 protection grade including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed

S & F in repair MCB DB made of sheet steel enclosures with detachable gland plates for flush/surface mounting with bus bars, neutral links and earth bar (without mcbs) , 240Volts SPN with 6 way Double door , IP-42 protection grade including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed

S & F in repair MCB DB made of sheet steel, powder painted with bus bar 200 A, neutral link, earth bar and Din rail , 240 Volts SPN with 4 way Double door IP-43-IK09 protection grade including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed

Supply and fix in repair for MCB TPN 415 Volts, 'C' series, breaking capacity 10 KA of rating 63Amps

Supply and fix in repair for MCB SPN 240 Volts, 'C' series, breaking capacity 10 KA of rating 63Amps

Supply and fix in repair for MCB SPN 240 Volts, 'C' series, breaking capacity 10 KA of rating 32-40 Amps

Supply and fix in repair for MCB SP 6-32 Amps 'C' series, breaking capacity 10 KA of rating

S & F in repair MCCB TPN 100Amps , 415Volts, 25KA ,4 pole.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in gound (Earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connecting to the galvanised iron earth lead wire of 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and earht strip protected by provision of GI light grade pipe 15 mm light grade bore including provision of pit in PCC (1:2:4) type B-1 using 20 mm graded of stone aggregate with PCC cover including 20mm bore pipe for wetering perforated at bottom 1.75 mtr long placed on top edge of earth plate common salt and charcoal (not less than 40 Kgs, 80 Kgs each) filling with fixing arrangement funnel wire mesh and earth work in hard dense soil returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electircal plate No 03 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion.

Vinod Enterprises

M/S SAMEER SUBHASH PATANI

Anand Trading Co

Kaushalya Buildcon

M/s. JBSR ENTERPRISES.

M/S K. K. Construction

SHILPVED

SHRI SWAPNAYOG ENTERPRISES

Alpha Construction

Samruddhi Construction