Special repair to bldg. No. ET-204 at CME, Pune

Amount

Dismantling of single layer Mangalore Pattern roof tile laid dry complete all as specified and directed

All as per item No.1 above, but bedded in lime or cement mortar complete all as specified and directed.

Dismantling battens for tiles, shingles etc, of any size including tilting fillets spacing exc 15 cm complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position

Dismantling boarding, any description, fixed in any position with nails

S&F rolled sections as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W (Gde E-250) Quality A complete all as specified and directed.

S & F For 6 mm thick ms plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachmentding etc. complete all as specified and directed.

Preparation of new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a of red oxide primer complete all as specified and directed

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc. complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley, gutters etc. complete all as specified and directed.

S&F steel work in tubular trusses including special washer etc., purlins, rafters, completer using ERW or induction butt welded tubes conforming to I.s 1161-1979 grade St.-240 complete all as specified and directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing confirming to Fe 410 - W Gde - 250 quality A etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc. complete all as specified and directed.

S & F for 1 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) exc 1.5 but n. Exc 4.00 sqm each and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) n. exc 1.50 sqm each and removing from site complete all as sepcified and directed.

S & F powder coated Aluminium sliding windows three track with two glass shutters using 4 mm thick glass tinted Modi guard and one shutter with stainless steel wire gauge wire cloth 0.31mm nominal dia of wire and width of aperture 1.61mm, using Aluminium powder coated sect, Aluminium cleat, PVC track, bearing, handle lock rubber beading, etc complete including taking down old window of any size. Note Size of aluminum sections are as under :- (i) Three track top & vertical – Jindal main – 2010 Section No 20621. (ii) Three track bottom - Jindal main – 2010 Section No 20620. (iii) Shutter vertical section - Jindal main – 2010 Section No 20606. (iv) Shutter top & bottom - Jindal main – 2010 Section No 20604 (v) Shutter vertical middle (interlock) - Jindal main – 2010 Section No 20605.

S & F for 4 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane etc. complete all as specified and directed.

S & F for galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples etc. complete all as specified and directed.

M&L for framed work such as grills or grating etc with ends of bars shouldered as framed guard bars conforming to Fe-410-0 or 310-0 all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube etc all as specified and directed.

S & F factory made solid PVC moulded door shutter, 30 mm thick 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and directed.

S& fixed factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered panticle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified and directed.

S& fixed 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to recieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and directed.

S&F 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamferred, put together with glue pinned at joints etc. complete all as specified and directed

Mild steel works as in bands straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminious paint and sanded, complete all as specified and directed.

Cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as spd.

S&F 150mm hasp and staple, mild steel, wire type stove enamelled black, including bolt to hinge plate and fixed with screw. complete all as specified and directed.

S & F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as specified and directed.

M&L 200 mm aluminium anodised, barrel tower bolts of extruded section and fixed

M&L 150 mm aluminium anodised, barrel tower bolts of extruded section and fixed

S&F 125mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 150 mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 300mm long Aluninium alloy, anodised , sliding door bolt with hasp , staple, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F For 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit all as directed.

All as per item No 38 above, but 20mm bore

S&F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specifeid and directed.

Refixing 15mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc all as specified and directed

S&F 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specified and directed.

Refixing 20 mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc all as specified and directed

M& L For Cutting chases, pinning in stone concrete black or slab , making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth etc. complete all as specified and directed.

S&F in repair vitreous china wash basin, white, flat back, size 630x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, waste coupling complete all as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including seat cover complete all as specified and directed

S&F in repair 10 ltr capacity PVC valveless , syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including brackeet and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

S&F For in repair brass chromium plated two way bib cock fancy type, 15mm bore ( min Wt. 550 grams) of approved make by EIC/ GE etc. complete all as specified and directed.

S & F For brass chromium plated, 15 mm bore healthfoucet, ( flexy type) 1.00 mtr. Long of approved make by EIC/GE etc. complete all as specified and directed.

S&F in repair 15 mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type , screwed down high pressure, with or without lettered 'Hot' or 'Cold' woth long shanks and flynuts, screwed for iron pipe complete all as specified and directed.

S&F PVC in repair connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 15mm dia stop valve chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and directed.

S & F in repair overhead shower 100 mm dia round shape single flow (ABS Body Chrome plated with grey face plate ) with Rubit cleaning system complete fixed to ceiling all as specified and directed by Engineer-in Charge. Make - Jaquar Cat No. OHS-1989 or equivalent approved make indicated in list of makes in tender as approved by GE.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair 75 mm PVC (SWR) bend any radius complete all as specified and directed

S&F in repair 75mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

M&L in repair 75mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair 75mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) bend any radius complete all as specified and directed

S&F in repair 110 mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

M&L in repair 110 mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair stainless steel sink, made out of 1.00 mm thick sheet for kitched with plug, washer pipe cast iron cantilever brackets, connecting union overall size 495x420mm bowl size 410mm x 330mm x160mm all as specified and directed. Make: Nirali/Diamond/Blue King/Kingston/

S&F in repair Brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges complete all as specified and directed.

S&F For in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stain steel bracket guard and railing 60 cm long etc. complete all as specified and as directed.

S& F in repair Soap dish holder complete as specified and directed by Engr-in-Charge.

S&F Toilet paper holder, Stainless Steel any type as specified and directed by Engr-in-charge.

S& F in repair Brass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed

S&F in repairs 19/20mm dia MS pipe powder coated of approved colour as in decoirative type curtain rods all as specified and as directed.

S&F in repairs brackets powder of approved decorative type suitable for fixing curtain rods of 19/20mm dia pipe incl fixing screws, drilling etc as per sample approved by Engr-in-charge all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced ) in ground floors and pavings not exceedidng 15cm thickness (below or aboved ground level) all as specified and directed.

M&L for 75mm thick PCC type D-2 (1:4:8) using 20mm graded stone aggregate as in sub base etc complete all as specified and directed

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6.

Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

Non- skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc.complete all as specified and directed.

M& L for rendering 10mm thick cement mortar in 1:4 as in backing coat complete all as specified and directed

Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

M&L for glazed ceramic coloured tiles in verticle surface 350mmx250mmx7mm /450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat 10mm thick cement mortar in 1:4 complete all as specified and directed,

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premisses complete all as specified and directed.

M&L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M& L For 18 to 20 mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed..

Roundidng to edges of stone slabs, such as in steps, cooking plateform and other similar situation complete all as specified and directed.

Racking out joints/pointing to random rubble masonry, polygonal rubble uncoursed or brought upto course complete all as specified and directed.

M&L raised pointing in CM 1:4 to random or polygonal rubble, uncoursed or brought upto complete all as sepcified and directed,

Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key scrubbing down with water all as specified and directed.

M&L rendering 15mm thick on stone masonary surfaces in CM 1:6 finished even and smooth with sagol over and including dubbing coat average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L rendering 15mm thick on stone masonry surfaces in CM 1:4 finished even andfair and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over one coat primer on walls complete all as specified and directed.

M&L preparation of newly plastered or unplastered surfaces on wall surfaces and applying two coats of cement base paint complete all as specified and directed.

Demolition of brick or stone/boulder masonary , built in cement mortar including all quoins, aarches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L precast solid block masonry of block 1:3:6 type C-1 wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed.

M&L complete removal of existing treatment and applying 3mm thick Birla wall care putty and applying two coat of Oil Bond distermper white or tinned over an coat of primer on walls, etc all as specified and directed.

All as per item No.96 above, but two coat of cement base paint without wall care puttycomplete all as specified and directed.

Dismantling water tanks and removing to store capacity exc 500 & n.exc 1000 ltrs complete all as specified and directed.

S&F For 500 ltr. Capacity rotational moulded polyethylene water storage tanks cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

M&L 18/19mm thick Pre-laminated board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination , fixed with screw to timber frame including taking down existing board of any description complete all as specified and directed.

M&L cover fillet (lipping) of tempered hard board 40mm wide, 6mm thick and fixing with screw complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) in 30mm complete all as specified and directed.

S&F in repairs 40mm dia cupboard knobs fixed with nut, screws and washers of mild steel bright finish complete all as specified and directed.

S&F in repais 150mm hasp and staple, aluminium anodised , wire type stove enamelled black, including bolt to hinge plate and fixed with screw. complete all as specified and directed.

M&L 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size 24mm x38mm x 0.7mm, cross tee of size 24mm x 28mm x 0.7 mm using porpose made members interlocking to each other and 40mm x 3mm flat made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes etc all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction including taking down old ceiling Make of GI Grid work : Armstrong/Swastik/Techno Grid Make of 'E' board : Everest/Indian Gypsum/Armstrong or equivalent approved .

Cleaning of existing 100mm dia sewage line upto 1.00 mtr depth from ground level by rodding or by any means and blowing water through pipe for efficient functioning complete as specified and directed by Engr-in-Charge.

Cleaning of existing 150mm dia sewage line upto 1.00 mtr depth from ground level by rodding or by any means and blowing water through pipe for efficient functioning complete as specified and directed by Engr-in-Charge.

Cleaning and bailing outof existing man holes 1.00 mtr deep (depth of manholes) by mechinical means using suction motor vehicle mounted and removing the same out of CME complex which incl removing slit, stone, solid particles to make smooth flow, complete as specified and directed by Engr-in-Charge.

All as per item 109 above, but depth of manholes exc 1.00 mtr but n.exc 2.00 mtr.

Excavation in trenches n.exc 1.50m wide and 1.50m depth for foundation, man hole etc and getting out in soft/loose soil

All as per item No.111 above, but in hard/dense soil

All as per item No.111 above, but in hard/dense soil

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete as specified and directed by Engr-in-Charge.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation and mass concrete complete as specified and directed by Engr-in-Charge.

Demolition of brick/ stone/PCC block masonry built in cement mortar/cement lime mortar all as specified and directed by Engr-in-charge.

M&L for precast plain cement concrete solid block masonry type C-1 1:3:6 (using 20 mm graded stone aggregate) , built in CM 1:6 exc, 10 cm width all as specified and directed by Engr-in-charge

M&L for rendering 15 mm thick cement plaster in CM 1:6 on stone masonry surface or other than fair face of brick work incl finishing even and smooth without using extra cement complete as specified and directed by Engr-in-Charge.

Taking down cement plaster of any description incl racking out joints, hacking for key etc complete as specified and directed by Engr-in-Charge.

M&L in repair for RCC drain pipes 150mm, class NP-3 laid in trenches and jointed complete with collar all as specified inlcuding demolition of old pipe complete as specified and directed by Engr-in-Charge.

All as item 120 above, but 200mm dia

M&L for PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in concrete bed to RCC drain pipes including packing under and hunching against side of pipes with concrete after they are laid and join ted, dia of pipe 150mm complete as specified and directed by Engr-in-Charge.

All as item 122 above, but 200mm dia

Returning, filling in, including spreading , levelling , watering and well ramming in layers not exceeding 25 cm in hard/dense soil complete as specified and directed by Engr-in-Charge.

Removing excavated material (soil) not.exceeding 50m and deposited where directed at a level not.exceeding 1.5 m above the starting point complete as specified and directed by Engr-in-Charge.

M&L for precast concete cover slab of 600 mm x 450 mm x 75mm thick for man holes with provision of collar all around to house the cover slab and collar fixed to wall of manhole in 1:6 cement mortar having smooth surface finish complete all as specified and directed by Engineer-in Charge.

M&L for precast concete cover slab of 600 mm x 600 mm x 75mm thick for man holes with provision of collar all around to house the cover slab and collar fixed to wall of manhole in 1:6 cement mortar having smooth surface finish complete all as specified and directed by Engineer-in Charge.

M&L for precast concete cover slab of 900 mm x 450 mm x 75 mm thick for man holes with provision of collar all around to house the cover slab and collar fixed to wall of manhole in 1:6 cement mortar having smooth surface finish complete all as specified and directed by Engineer-in Charge.

M&L for PCC (1:2:4) type B1, using 20mm graded stone aggregate as in coping, bands, plinth coarses, parapets, kerbs etc like incl weathering, slightly rounded or chamfered throating complete all as specified & directed.

M & L cutting hole in brick walls/stone walls exc one brick but not exc 2 bricks for any perpose and making good dismantled position in cement mortor 1:3 or cement concret 1:2:4 type B-1 as required complete all as specified and directed by Engineer-in Charge.

Taking down carefully aluminium point wiring (light, fan, socket or power), complete (fitting such as switches, ceiling rose, pendent, regulators etc) removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately and making dood disturbed surfaces of wall, floor to match with existing surface etc.

M&L for point wiring for ligh/fan with FRLS cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing/caping with all accessories and 1.00 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface/ flush type with PVC sheet for mounting fittings such as switches, sockets, fan regulators etc complete all as specified and directed for one light/fan /bell point controlled by one switch in and includinding taking old unserviceable point wiring. & Making good to disturbed surface of wall etc

One light point controlled by one switch 5 Amp

One Fan/ Exhaust fan point controlled by one switch

Socket outlet, three pin, 5 Amp, independent

Socket outlet, three pin 5 Amps on the same board

All as per Item No.132 above, but ,with stranded copper conductor 2.5 Sq. mm (nominal area), including PVC insulated stranded copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly complete all as specified.

Ceiling rose, surface Bakelite suitable for 3 pin 230 volt 50 Hz AC supply complete all as specified and directed.

Switch piano, flush type, single pole, one way, and 5 Amp, 230 volt complete all as specified and directed.

Switch piano, flush type, single pole, one way, and 15 Amp, 230 volt complete all as specified and directed.

Socket outlet multipurpose having provision for 3 pin, 6 Amp and 2 pin, 6 Amp, piano flush type complete all as specified and directed.

Socket outlet multipurpose having provision for 3 pin, 15 Amp and 3 pin, 5 Amp, piano flush type complete all as specified and directed.

Supply and fix step fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply

Supply and fixing bell push flush type , 5 amps , 240 volts

Supply and fixing Bell AC, 230 volts single pole

Supply and fix surface wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver for LED tube complete with retrofit LED energy saving recess/surface mounted luminaries, high efficiency diffuser for soft glare fee light of capacity 20 watt suitabe of operation on 230 volt 50 Hz AC supply complete all as specified and as directed by Engineer-in-charge.

S&F building security LED light fitting 35 Watt , energy saving and environmental friendly long life LED fitting made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 including suitable size bracket incl taking down old UNSV one.

Taking down ceiling fan of any size/sweep after disconnecting the wire from existing ceiling rose and refixing the same after cleaning dust, oiling greasing etc including providing flexible three core from ceiling rose to connector of fan

Taking down electric water heater (geyser) of any 25/50 ltr capacity and refixing the same after repair alongwith connected accessories such as PVC connection pipe, fastner etc complete all as specified and directed. Note : cost for spare parts required for repair of geyser is deemed to be inclusive in the unit rate of this item.

Supply and fix exhaust fan AC single phase 230/ 240 volts of size 250 mm sweep, 1400 rpm, with louvers and all fixing arrangements such as plywood 18mm thick of suitable size all as specified and directed.

S&F in replacement enclosure, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps, 240 volt incl taking down old UNSV one.

Supply and fix sheet metal enclosures TPN DB 4 way 415 volts double door

Supply & fix MCB 4 Pole 'B' series 100 amps capacity AC 415 V,10kA complete all as specified and directed

S&F Sub main wiring with approved colour coding as per IS with Two single core PVC insulated cable with stranded copper conductor of size 06 Sq. mm nominal area and drawing into PVC conduit including PVC insulated 06 Sqmm (nominal area) stranded copper conductor earth wire complete. NOTE : Two runs of 06 sqmm cable, one run of 06 sqmm earth cable and one run of PVC conduit will be measured as one unit

S & F in replacement MCB distribution board Double door SPN 240 volts 8 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc incl taking down old unserviceable one.

Supply and fixing of MCB Single pole rated capacity 5 to 32 A, 240 V breaking capacity 10 KA C series. Make - Indoasian /Schneider/Siemens

Supply and fixing of MCB Single pole and neutral rating capacity 40 to 63 Amp, 240 V breaking capacity 9KA C series. Make - Indoasian /Schneider/Siemens

M&L for earthing complete with GI earth plate electrode 60x60cmx6mm thick burried directly in ground in earth pit not less than 2.25 mtr depth below normal ground level with top edge of the plate vertically to depth of not less than 1.5 mtr below ground level connected to & including GI lead 4 mm dia as earthing lead connecting to equipment by means of GI bolts & nuts etc with provision of charcoal and salt etc all as per electrical plate No-3 of SSR part-I 2009 including RCC cover and MS angle iron frame, watering with GI pipe 20 mm dia (medium grade) & MS funnel, concrete pit including excavation and earthwork in any strata and testing on completion etc. complete all as specified and directed by Engineer-in-charge.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for taking out cable etc for repairs / laying cables etc and getting out in following type of strata complete all as specified and as directed by the Engineer-in-Charge.

Soft/Loose soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by the Engineer-in-Charge.

Removal of excavated material [soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M & L for bituminous road cutting to a width of 45 cm and depth 50 cm for laying LT UG cables and making good with cement concrete 1:3:6 type C 1 (using 20 mm graded stone aggregate)

Supply, laying and testing cable XLPE insulated screened pvc bedded galvanised steel strip or wire armoured , electric power cables ( heavy duty) with stranded aluminium conductor 1100 volts grade in trenches/ passing through pipe/fixing on walls, floors etc incl using suitable clamp of cross sectional area 3.5 core 25 Sqmm in and including taking out old one all as specified and directed.

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 50 mm and inner dia 38 mm polythylene with smoooth inernal and profiled external surface for non pressue under ground cable incl couplers & bends complete all as specified and directed.

Supplying and laying GI tubing light grade of size 40mm dia bore for encasing cables for mechanical protection, laid under Plinth / Floors/ Paths Culverts or fixed on wall or concealed in wall/floor or along poles or as street light poles or as street light mounting bracket with complete accessories such as bends/ sockets/ reducers/ saddles incl necessary threading/drilling works all as specified and directed by Engr-in-charge.

Mukund Engineers and Contractors