SPECIAL REPAIR TO BUILDING NO. ET-169 AND OTHER SANCTIONED WORK AT HATTIGOR MILITARY STATION UNDER GE RANGIA

Amount

Dismantling Unframed timber scantlings 40 Sq. cm and over in section and in any position, complete all as specified and as directed by Engineer-in-charge.

M&L for 2nd class hard wood in scantling wrought timber framed and fixed complete all as per specified and as directed by Engineer-in-charge.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, complete all as specified and as directed by Engineer-in-charge.

M & L for G I Wire netting 0.9 mm dia and 12 mm mesh lathing to wood or metal studding, joists, etc., in walls, ceilings, stanchions, beams, etc., including all laps, cutting and waste, complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engineer-in-charge.

Demolition of brick work built in cement mortar complete all as specified and as directed by Engineer-in-charge.

M&L for brick work with sub-class `B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius in cement mortar 1:6, complete all as per specified and as directed by Engineer-in-charge.

"M&L for 15 mm thick rendering on fair faces of brick work or one side of lathing in cement mortar (1:4), surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L rendering 10mm thick on other side of lathing in cement mortar 1:6 be finished fair & even without using extra cement, complete all as specified and as directed by Engineer-in-charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation,etc) or insulation board/Slabs/blankets of any thickness including cover fillets, complete all as specified and as directed by Engineer-in-charge.

M&L for 4mm thick Non Asbestos fiber Cement Designer E- board ceiling of size (595x595)mm fixed in powder coated GI frame (snapgrid) of standard section as per manufacturers instructions with the 3mm thick GI suspender in ceiling complete all as per specified and as directed by Engineer-in-charge.

Demolition of unreinforced cement concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge.

M&L for 75 mm thick Cement concrete type C1, 1:3:6 (using 20 mm graded stone aggregate) in footpath/ hard-standing / pavings / plinth protections, finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

Taking down shutters of any description not exc. 1 sqm each, complete all as specified and as directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each, complete all as per specified and as directed by Engineer-in-charge.

Taking down chowkat or frame not exceeding 1.5 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge.

M&L 35 mm thick second class hardwood glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc (without sash bar) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of member (Bottom 250mm, stiles 100mm, top 120mm & lock rail 160mm wide) as specified in SSR part I section & clause 8.24 (a) complete all as specified and as directed by Engineer-in-charge.

S&F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. for windows and ventilators etc complete all as per specified and as directed by Engineer-in-charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube in opening as per specification complete all as per specified and as directed by Engineer-in-charge.

Supply and fixing factory made solid PVC moulded door shutter 28 to 30mm thick (style), with 2,4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in the frame at site as per specification complete all as per specified and as directed by Engineer-in-charge.

S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides, complete all as per specified and as directed by Engineer-in-charge.

S & F 3 mm thick Sheet glass, ordinary quality in squares not exceeding 0.5 Sq. M in each pane fixed with cut & mitred beads, complete all as specified and as directed by Engineer-in-charge.

S & F galvanised mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge.

S&F 125mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge.

S & F 75 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C-21, complete all as per specified and as directed by Engineer-in-charge.

S&F 100 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C-21, complete all as per specified and as directed by Engineer-in-charge.

S & F 125 mm long Extruded Aluminium alloy handles, fabricated type, anodised, complete all as per specified and as directed by Engineer-in-charge.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised, complete all as per specified and as directed by Engineer-in-charge.

S&F aluminium alloy 300mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

S&F 300 mm long Helical door Spring of approved quality, complete all as per specified and as directed by Engineer-in-charge.

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

Dismantling boarding, any description fixed in any position with nails, complete all as specified and as directed by Engineer-in-charge.

M&L for 2nd class hardwood 20mm clean sawn boarding with butt joints fixed with nails in any situation (except flooring and skirting), complete all as per specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated or semi-corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

S & F Mild steel work in hand rails, wind ties, posts and struts in fencing screwed or welded to shape as directed, including all necessary drilling, bolting or riveting etc., and similar work confirming to Fe 410 - O or Fe 310 - O, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of oil bound distemper on walls including one coat of chalk whiting primer, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing old distempared surfaces including washing, rubbing down and stopping and applying one coat of oil bound distemper on walls, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of cement base paint on wall over a coat of alkeli resistent primer, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing old painted surfaces including washing, rubbing down and stopping and applying one coat of cement based paint on walls, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing surfaces of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with two coats of cresote oil, complete all as specified and as directed by Engineer-in-charge.

M & L for preparation of old painted surface of wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M & L for preparation of newly untreated wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as per specified and as directed by Engineer-in-charge.

S&F coloured non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in CM 1:4 complete all as per specified and as directed by Engineer-in-charge.

M&L for Coloured Glazed ceramic tiles 250 x 350 x 6 or 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10 mm thick screed in CM (1:4) complete all as per specified and as directed by Engineer-in-charge.

Taking up or down 15 mm bore steel tubing and connections, complete all as per specified and as directed by Engineer-in-charge.

Taking up or down 20 mm bore steel tubing and connections, complete all as per specified and as directed by Engineer-in-charge.

Taking up or down 25 mm bore steel tubing and connections, complete all as per specified and as directed by Engineer-in-charge.

S&F GI tube 15 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge.

S&F GI tube 20 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge.

S&F GI tube 25 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge.

Dismentaling water tanks of capacity exc. 500 and not exc. 1000 ltrs, complete all as per specified and as directed by Engineer-in-charge.

S&F rotational moulded polyethylene water storage tanks (cylinderical, vertical with closed top) of 1000 Ltrs capacity hoisted and fixed in position, complete all as per specified and as directed by Engineer-in-charge.

S&F 20 mm dia ball valves, PTMT high pressureof expoxy coated aluminium rod and hign density plastic ball (200 gms), screwed for iron pipe or brass ferrule complete all as per specified and as directed by Engineer-in-charge.

S&F in repair gun metal globe or gate valve, with iron wheel head screwed both ends for iron pipe of 20 mm bore complete all as per specified and as directed by Engineer-in-charge.

M&L precast Coloured cement concrete chequered tiles 300x300x25mm thick set jointed and pointed in with grey cement and pigment laid over and including 20mm thick screed bed in CM 1:6 in floorings, complete all as per specified and as directed by Engineer-in-charge.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as per specified and as directed by Engineer-in-charge.

Removing excavated material not exc. 50 m & depositing where directed at a level not exc. 1.5 m above starting point complete all as per specified and as directed by Engineer-in-charge.

M&L for PCC (1:4:8) type D2 ( using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as per specified and as directed by Engineer-in-charge.

Forming embankments incl raising (or lowering) earth spreading in layer n. exe. 30 cm thick, watering, ramming/ rolling and finishing to reqd size and shape, etc, n. exe. 1.5m hing from base complete all as per specified and as directed by Engineer-in-charge.

Removing excavated material exc. 1.50 km and 5km depositing where directed at a level not exc. 1.5 m above starting point complete all as per specified and as directed by Engineer-in-charge

M&L for hard core of gauge exc. 63 mm but not exc.100 mm, deposited, spread and levelled in layers not exc. 150mm thick, watered and rolled/rammed to a true surface complete all as specified and as directed by Engineer-in-charge.

M&L 150 mm thick PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in floor, finished even and smooth using extra cement including necessary foem work complete all as specified and as directed by Engineer-in-charge.

M&L for forming 12mm thick expansion joint in 150mm thick slab filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound grade 'B' complete all as specified and as directed by Engineer-in-charge.

S&F 12mm thick fiber glass reinforced translucent plain sheeting fixed with coach screw and washer in roof, wall etc. complete all as specified and as directed by Engineer-in-charge.

Excavation in post holes (or similar holes) each not exc. 0.5 cum in soft/loose soil and getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing of surplus soil to a distance not exc. 50 meters and making good surface, complete all as per specified and as directed by Engineer-in-charge.

M&L for PCC 1:3:6 type C-2 (40mm graded stone aggregate) as in foundations, fillings and mass concrete complete all as per specified and as directed by Engineer-in-charge.

S&F MS steel work in tubular trusses including special shaped washers etc., complete using ERW or induction butt welded tubes confirming to IS 1161- 1979 graded St 240, complete all as per specified and as directed by Engineer-in-charge.

S&F rolled mild steel work in plates (plain or chequered) channels,square cut or notched (ordinary and counter sunk) forming holes,riveted, bolted or welded attechment conforming grade Fe-410-w (Gde-E-250) quality-A, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated steel or iron surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide, primer over 10cm width or girth complete all as specified and as directed by Engineer-in-charge.

M&L for painting lines, dashes, arrows, letters etc. on concrete ground and like not exc.10cm wide with road marking paint, white or golden yellow complete all as specified and as directed by Engineer-in-charge.

M&L for painting lines, dashes, arrows, letters etc. on concrete ground and like exc. 10cm wide with road marking paint, white or golden yellow complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge.

Taking down carefully aluminum/copper point wiring (light fan, socket or power) complete incl fittings and fixtures such as switches, sockets, light fittings, ceiling rose, pendants, lamp holders, shade conical, regulators etc and removing unserviceable fittings and fixtures with wiring cable, battens, wooden boards etc from site and making good disturbed surfaces of walls, floors, ceiling etc all complete all as specified and directed complete all as per specified and as directed by Engineer-in-charge.

Taking down carefully unserviceable main switches and DB’s including wooden boards and removing from site including making good disturbed surfaces of walls complete all as per specified and as directed by Engineer-in-charge.

Dismantling of house service brackets of any size and type and making good the distrubed wall surfaces complete all as per specified and as directed by Engineer-in-charge.

M&L for point wiring with 1.5 sqmm size (nominal area) PVC insulated unsheathed single core multi stranded FRLS copper conductor cable drawn into and incl PVC casing capping sleeves and caps of adequate width and length with all accessories and fittings like bends . elbow crosses etc with PVC round block and PVC terminal boxes with 3.00mm thick laminated sheet cover for mounting fittings etc like switches sockets and fan regulator incl 1.5 sqmm size PVC insulated multistranded FRLS copper conductor cable as earth continuity conductor and connected to earth dolly complete all as specified and as directed for one light point controlled by one switch, complete all as per specified and as directed by Engineer-in-Charge.

All as per serial item no. 82 above but for one ceiling fan/exhaust point controlled by one switch

All as per serial item no. 82 above but for one 3 pin socket combination 5 AMPs on independent board.

All as per serial item no. 82 above but for one 3 pin socket outlet 5 AMPs on same board.

All as per serial item no. 82 above but with 4 sqmm (nominal area) cable with 4.00 sq mm size copper earth continuity conductor of green colour for 3 pin socket outlet, 15 Amps on independent boards complete all as per specified and as directed by Engineer-in-Charge.

Supply and fix switch socket combination 05/16 Amp 6 pin flush type, complete all as specified and as directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 230 volts, flush type, 6 pin, 5 Amp flush type complete all as specified and as directed by Engineer-in-charge.

Supply and fix switch socket combination 6 Amp 5 pin flush type, complete all as specified and as directed by Engineer-in-charge.

Supply and fix switch piano flush type, 6 Amps 240 volts single pole one way, complete all as specified and as directed by Engineer-in-charge.

Supply and fix ceiling rose surface backelite three terminals, PVC/polycarbonate, insulated body, complete all as specified and as directed by Engineer-in-charge.

Supply and fix fan regulator electronic type, rotary step, Socket type 240 Volt, complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED tube light fittings with regal batten for LED, wall mounted, extruded head dissipation & separate with LED tube light (double side connection) 18 W LED 4', 230 V complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to tube light fitting complete all as specified and as directed by Engineer-in-charge.

Supply and fix angle type lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting including 10 Watt LED Lamp complete all as specified and as directed by Engineer-in-charge.

S&F PVC rectangular block for mounting, DBs, etc. with 3mm thick plastic laminated sheet cover of size 250 x 200 x 50 mm deep complete all as specified and as directed by Engineer-in-charge.

Supply and fix sheet metal enclosure powder painted for MCB SPN 8 way DB double door with din rail and suitable bus bar including making good to the disturbed surface matching with the existing complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SPN 240 Volts 6-32 Amp breaking capacity 10 KA rating complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SP 240 Volts 6 to 32 Amps breaking capacity 10 KA rating complete all as specified and as directed by Engineer-in-charge.

S&F in repair 1100 volts grade heavy duty 16 sqmm cable PVC insulated stranded aluminum conductor served with inner sheathing of PVC tape and overall PVC sheathed for service connection suspended by insulating hangers not more than 1 Mtr apart including 4 mm suspension wire one twin core cable flat or circular, complete all as specified and as directed by Engineer-in-charge.

Taking down old ceiling fan/exhaust fan and refixing after cleaning to its original position/location and testing complete all as specified and as directed by Engineer-in-charge.

S&F building security light fittings 1x 15 Watt LED New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP openning seperate driver compartment with IP65 protection and impact resistance of IK07 and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size, complete all as specified and as directed by Engineer-in-charge.

S&F House service bracket (Hook type) complete with 40 mm dia GI pipe 3.00 m long, medium grade, two Nos. of 90 degree bends, M.S hook and stay or guy complete all as per specified and as directed by Engineer-in-charge.

S&F building light bracket made out of GI tubing 25 mm bore medium grade 1.20 Mtr long bend to required shape as in bracket for street light fittings fixed with two pair or MS flat iron 40mm x 5mm size and 30cm long clamp of required shape with bolts nuts and washers suitable for steel tubular pole including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-charge.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 5 of SSR PT 1, 1991 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) including taking down old unserviceable one, complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

M & L for 9 meter long hot dipped galvanised octagonal pole with top A/F 70 mm bottom A/F 130 mm made out of 3mm thick HT sheet along with base plate of size 200x200x16mm including 150 mm long single arm bracket made out of 48 mm dia GI pipe and M20x600 mm long 'J' type EN8 grade foundation bolts along with template including the following:- (a) MCB SP 6A 230V, 10KA mounted on 3mm thick hylamsheet-1 No (b) 4 way connector bolt type 2 Nos alongwith locking arrangement weather proof and water proof control space. Note :- (a) The rate quoted deemed to include the cost 50 mm PVC pipe from cable trench to center of the pole concrete and 'J' type EN8 grade foundation bolts. (b) The rate quoted deemed to included the cost of connecting of incoming and outgoing cable in new octagonal poles through PVC pipe including taking out loop extending upto juction box connecting complete including necessary earth work.

S&F PVC insulated, electric cable with copper conductor, 1100 volts grade having cross-sectional area 2.5 Sqmm 3 Core complete all as specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 10 mm dia. and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge.

M&L for RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in footing and column up to ground level complete all as per specified and as directed by Engineer-in-charge.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed by Engineer-in-charge.

S&F 150Watt street light fittings suitable for New generation energy saving and environmental friendly long life versatile pressure die cast aluminium housing with high power LED as lighting source , potted driver compartment, toughend glass with IP66 protection and impact resistance of IK07 complete all as specified and as directed by Engineer-in-charge.

S&F XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminum conductor, 1100Volt grade on walls with fixing acessories of size 16 Sqmm 2 Core including testing complete all as specified and as directed by Engineer-in-charge.

Supply & laying 32 mm dia High density polyethylene pipes (HDPE) for Cable protection of pressure rating 6 kgf/cm2 laid in trenches complete all as specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

M/S SITAL BUILDERS