Renovation of 2nd Floor, Main Building NIScPR, Pusa

Amount

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including cutting chase in brick wall for fixing, rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. (i) Granite stone slab colour black, Cherry/Ruby red

(a) Area of slab upto 0.50 sqm

(b) Area of slab above 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Stone tile (polished) work for wall linning over 12 mm thick bed fo cement mortar 1:3 ( 1 cement : 3 coarse sand) and cement slurry @ 3.3 kg /sqm including pointing in white cement complete. (i) 8 mm thick (a) Granite of any colour and shade

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). (a) kiln seasoned and chemically treted hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : (a) 2nd class teak wood 50x12 mm

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

(a) For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) (i) Powder coated aluminium (minimum thickness of powder coating 50 micron)

(b) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) (i) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. (a) With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complet

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.0 mm thickness

Providing and fixing sun control film of 2 mil thickness and total solar energy rejection above 60% in required colour (of make Garware and equivalent) including removal of old film (whereever required) complete as per the direction of Engineer-in-charge.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 75x63x3.2 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : (a) 250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : (a) 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (a) Twin rubber stopper

Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete. (a) Kiln seasoned and chemically treated hollock wood

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete.

(a) 12 mm thick.

(b) 25 mm thick.

Providing and fixing 6mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge.

Providing and fixing 6mm thick Pinup Board in modular work Station all complete as per direction of Engineer-in-charge.

Providing and fixing Writing Board in modular work Station all all complete as per direction of Engineer-in-charge.

Providing and fixing aluminum U beading of required size to Pre-laminated/ flush door shutter, including fixing etc. complete as per direction of Engineer-in-charge.

Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).

(a) 18 mm thick

(b) 25 mm thick

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge.

Providing and fixing magnetic catcher of approved quality in cupboard /ward robe shutters, including fixing with necessary screws etc. complete Double strip (horizontal type)

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. (a) 50 mm

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. (a)125 mm

Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineerin- charge.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. (a) Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. (a) Double charge vitrified tile polished finish of size

(i) Size of Tile 600 x 600 mm

(ii) Size of Tile 600 x 1200 mm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

(a) 12.5 mm thick tapered edge gypsum moisture resistant board

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. sqm 1718.70. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. Complete

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Providing and applying plaster of paris putty of 2 mm or of more suitable thickness over plastered surface to prepare the surface even and smooth complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : (a) Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : (a) Of area 3 sq. metres and below

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 meters lead.

Dismantling aluminium doors, windows, fixed glazing including disposal of unserviceable surpplus material and stacking of serviceable material with in 50 metres lead as directed by Engineer-in-charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer (Make - CERA/ PARRYWARE/ HINDWARE)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (i) Concealed work, including cutting chases and making good the walls etc. (Make - SUPREME/ FINOLEX/ASTRAL/PRINCE/only) (a) 15 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall (Make - SUPREME/ FINOLEX/ASTRAL/PRINCE/only) (a) 15 mm nominal dia Pipes

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 g

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931: (a) 15mm nominal bore (Make - CERA/ PARRYWARE/ HINDWARE)

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. (a) 15 mm nominal bore with 45 cm length

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Providing and fixing 12 mm thick frameless toughened glass partition of approved brand and manufacture, including providing and fixing necessary arrangement fitting of "Ozone" make connectors glass to glass, glass to wall at any angle etc. including joining sealing to glass, glass to glass, wall to glass at any angle and making necessary holes etc. as per direction of Engineer- in - charge.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing double action hydraulic floor spring and making necessary holes including S.S. door handle (450mm x 30 mm dia hollow) & mid lock Of’ ‘’Ozone’’ make for fixing required door fittings, all complete as per direction of Engineer-in-charge.

S/fixing Frosted glass films on toughened glass partitions/doors any design copmlete as per direction of Engineer-in- Charge

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 (a) Upto 5 mm depth and 5 mm width

Providing and fixing sandwitches type signboards using 5mm A-cast clear acrylic base, 3mm A-cast clear acrylic front with SS spacers , high quality digital print on non-adhesive material complete as per satisfaction of engineer-in-charge

Providing and fixing vertical blinds 100mm Regular quality of MAC/VISTA make made from 100% polyester yarn coated with fade resistant polymer to ensure complete opaquity with zero light transmittance having suitable coating on exterior, including all fixtures and fittings complete in all respect as per choice, design and instructions of the engineer-incharge .

Providing and fixing PVC pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Make - SUPREME/ FINOLEX/ASTRAL/PRINCE/only)

Supplying and deploying adequate manpower for shifting of office equipment, stationary material, furniture items etc. from the site of work to the designated place and re-arranging the same to the site after work completion as per requirement complete as per direction of engineer-in-charge.

Buy Back Wooden Doors Shutter with frame/Chowkhat & its fittings complete as an is where basis taking out of NIScPR building premises including loading unloading and transportation etc. Complete.

Buy Back old dismantled Aluminium Sections taking out of NIScPR building premises including loading unloading and transportation etc. complete. The weight of the material will be ascertained on the basis of loading vehicle and the tare weight of the vehicle after weighting the same at weigh bridge (Dharam kaanta). The charges will be borne by the contractor.

Buy Back old dismantled M.S. Sections taking out of NIScPR building premises including loading unloading and transportation etc. complete. The weight of the material will be ascertained on the basis of loading vehicle and the tare weight of the vehicle after weighting the same at weigh bridge (Dharam kaanta). The charges will be borne by the contractor.

Wiring for light point / fan point/ exhaust fan point/ call bell point with1.5 sq mm FR PVC insulated, copper conductor single core cable in surface / recessed PVC conduit with modular switch( Legrand or equivalent) modular plate suitable GI box and earthing the point with 1.5 sq mm FR PVC insulated copper conductor single core cable of make:- Polycab/Havells/KEI etc. as required.

Group C point

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. Make:-Polycab/Havells/KEI

2 X 2.5 sq. mm + 1 X 2.5 sq mm earth wire

2 X 4 sq mm + 1 X 4 sq mm earth wire

2 X 6 sq mm + 1 X 6 sq mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. Make:-Delton/ Polycab/Havells

Laying of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. (cable will be supplied by NIScPR)

1 run of cable

Testing and Punching of Cat-6 cable in the existing RJ-45 wall sockets and network switches.

Supplying, installation, testing & commissioning of cubical type floor mounting supported by MS angle LT panel suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system having 1700W X 2175H X 400D MM (Approx.) fabricated in compartmentalized (preferably) design from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having 400 Amp capacity extensible type TPN aluminium alloy bus bars of high conductivity, bottom base channel of MS section, entire panel shall have a common copper earth bar of size 50 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with suitable PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in i/c providing following switch gears :- (a) MAIN INCOMER -01 No (b) CVS 400A 4P MCCB, 36KA T/M (Make - SCHNEIDER)- 01 No (c) SPREADER FOR 400A 4P MCCB (Make - SCHNEIDER)- 02 Nos (d) ROTARY HANDLE FOR 400A 4P MCCB (Make- SCHNEIDER)- 01 No. (e) INDICATING LIGHT 'R / Y / B' (Make - ESBEE)- 01 No (f) AMMETER, CL.1.0, (0-400A), DIGITAL (Make - CONZERV)- 01 No. (g) VOLTMETER, CL.1.0, (0-500VAC), DIGITAL (Make- CONZERV)- 01 No (h) ASS (Make - Salzer)- 01 No (i) VSS (Make - Salzer)- 01 No (j) CT- 400/5A, CL.1.0, 10VA, TAPE WOUND (Make - AE/HA)- 03 Nos. (k) CONTROL MCB, 6A, SP (Make - SCHNEIDER)- 03 Nos. (l) CT TERMINALS (Make - PH/CWELL)- 04 Nos. (m) NEUTRAL LINK (Make - REPUTE)- 01 Nos. Outgoings: (a) 100A, FP, MCCB- 12 nos, (b) CVS 100A 4P MCCB, 25KA T/M (Make - SCHNEIDER)- 01 no., (c) SPREADER FOR 100A 4P MCCB (Make- SCHNEIDER)-02 no, (d) ROTARY HANDLE FOR 100A 4P MCCB (Make - SCHNEIDER)-01 no., MCB OUTGOINGS: (a) 63A 4P MCB 10KA (Make - L&T)- 12 Nos (b) POWER TB (Make - PH/CWELL)- 48 nos. GENERAL ITEMS :- MS ENCLOSURE DULY POWDER COATED- 01 No. (a) AL. BUSBAR 400A TPN (Make - HINDALCO)- 01 No. (b) SIZE FOR EACH PH. 50X10MM- 02 Nos. (c) SIZE FOR NEUT. 50X05MM- 02 Nos. (d) SIZE FOR EARTH 50X05MM- 02 Nos. (e) BUS BAR SUPPORTS, HARD WARE- 01 No. (f) POWER & CONTROL WIRE ETC.- 01 No. (g) PANEL ASSEMBLE- 01 No.

Supplying , installation ,testing & commissioning of 630Amp,4-pole MCCB 36 KA with microprocessor release O/L, S/C , extended handle and spreader link for 630 amp FP MCCB including removal of old existing change over switch and fixing of new MCCB suitable to retrofitting in our LTpanel. The retrofitting work consists of removal and refabrication of front door opening if required, making & fixing of extension link suitable for 630 Amp ,changing of necessary internal busbar, modifications and fitment of MCCB in proper position and suitable for manual operation . Make:- Schneider/L&T/ABB

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate as required. Make:- Legrand/C&S/MK

5/6 amps switch

3 pin 5/6 A socket outlet

Telephone socket outlet

Supplying,installation,testing and commissioning of RJ 11 double telephone socket with shutter legrand make alongwith metal flush /PVC boxes legrand make and modular white plates legrand make on surface/ recess/ table trunking trench as required.Make:- Legrand/C&S/MK

Providing & fixing MDF 50- Pair with Krone including connections of telephone wire in the MDF/Krone etc complete as required. Make:- ADC Krone

Supplying,installation ,testing and commissioning of modular type legrand make internet point RJ 45 (Information outlet) with modular metal/PVC box and plate in floor or wall including cutting/ chasing etc complete as required. Make:- Legrand/C&S/MK

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.Make:- Legrand/C&S/MK

Fixing of following sizes of PVC conduit along with accessories in surface/recess/table trench including cutting the wall and making good the same incase of recessed conduit as required. (PVC conduit pipe will be provided by NIScPR )

Supply andf ixing of following sizes of PVC conduit along with accessories in surface/recess/table trench including cutting the wall and making good the same incase of recessed conduit as required. Make:- Setia/AKG

Supply & fixing of suitable size unbreakable box deep on surface or in recess with suitable size modular plate cover in the front including providing and fixing 2 Nos 6/10/15 Amps modular type socket outlet with 2 nos 16 Amps modular type switch, connections, painting etc. complete as required. Make:- Legrand/C&S/MK

Supply & fixing of suitable size unbreakable box deep on surface or in recess with suitable size modular plate cover in the front including providing and fixing 3 Nos 6/10/15 Amps modular type socket outlet with 1 no. 16 Amps modular type switch and suitable blanking plate connections, painting etc. complete as required. Make:- Legrand/C&S/MK

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

300 mm width X 50 mm depth X 1.6 mm thickness

S/F following size/modules power strip consisting of multistandard modular socket (3nos) +16 amp switch (1 no) modular Make :- Legrand/C&S/MK

8 Module

Supplying & fixing 'C' series, SP MCB : Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'C' series, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make:-Legrand/C&S/MK

Single Pole

Supplying and fixing following rating miniature circuit breaker 'c' series in the existing MCB DB complete with connections, testing and commissioning etc as required. Make:-Legrand/C&S/MK

MCB 32 Amp DP 240 V

MCB 40 Amp SP 240 V

MCB 63 Amp TPN 415 V

MCB 40 Amp DP 240 V

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board , 240 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (but without MCB/ RCCB/ Isolator)Make:- Legrand/C&S/MK

12 way ,Double Door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . Make:- Legrand/C &S/MK

4 way (4 + 12), Double door

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. Make:- Legrand/C&S/MK

100 A,30KA,FPMCCB

125 A,36KA,FPMCCB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required. Make:- Legrand

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) Make:- Legrand/C&S/MK

4 way (4 + 12), Double door

Supply&fixing one number metal one way enclosures of DPX 160 ER MCCBs no of modules 3P & 4P on surface with drilling holes and making connections etc complete as required. Make:- Legrand/C&S/MK

Supplying, installation, testing & commissioning of 34W, LED light fitting suitable for armstrong ceiling and grid ceiling of cut size 595mm X595mm X65mm (LXWXH) with complete electronic driver as required including all needed materials i.e hanging of lights with metallic chain for completing the work.Make:- Havells/ Philips/Disano

Supplying, installation, testing & commissioning of 15 W recess mounting downlighter with pressure die cast aluminium heat sink and diffuser in white powder coated finish with integral electronic low THD LED driver driver suitable for armstrong ceiling and grid ceiling of cut size Ø 138mm, height 90mm as required including all needed materials for completing the work.Make:-Havells/Philips/Disano

Supply and fixing rigid PVC trunking for cable management of follwing size along with the accessories i.e end cap clip in surface/ recess/hanging including cutting the wall and making good the same.Make:-AKG

25mmX30mm(WxH)

45mmX45mm(WX H)

60mmX75mm(WxH)

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.Make:-Havells/Almonard/Crompton

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.Make:-Legrand/C&S/MK

Splicing of 6 core fibre optical armoured cable, outdoor single mode with LIU terminations as required.

Dismatling of existing light fittings ,armoured cables ,switch plates,distribution boards, MCBs, earthing wires ,metal boxes etc complete as required and deposite the same to the engineer incharge.

Supplying of one number ISI mark following sizes aluminium conductor XLPE insulated armoured power cable of 1.1 KV grade as required. Make:-Polycab/Havells/ KEI

4 core X 6 sqmm

4 core X 16 sqmm

4 core X 25 sqmm

4 core X 35 sqmm

4 core X 300 sqmm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aliminium conductor cable of 1.1 KV grade as required.Make:- Dowells

4 core X 6 sqmm

4 core X 16 sqmm

4 core X 25 sqmm

4 core X 35 sqmm

4 core X 300 sqmm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Upto 35sqmm(Clamped with 1 mm thick saddle)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp

Providing and fixing 10 SWG Dia wire on surface or in recess for loop earthing as reqd.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supply and fixing of suitable size copper refrigerent pipe with proper insulation along with control wiring ,power cable and PVC drain pipe for interconection of outdoor units and indoor units along with.

Installation/re-location of existing split type air conditioning units( only indoor ) including power cable ,PVC channel,drain pipe including top-up of referigerant etc for the split A/C unit complete in all respect( But without power points).

Buy back the dismantled existing GI AC ducts and supporting iron members and old reinforced bars from brick walls etc. taking out of NISCAIR building premises including loading unloading and transportation etc. complete. The weight of the material will be ascertained on the basis of loaded vehicle and the tare weight of the vehicle after weighing the same at weigh bridge.

Mahendru Consultants

S P CONSTRUCTION